Temperature and alkaline hydroxide treatment effects on hydrogen sorption characteristics of multi-walled carbon nanotube–graphite mixture

Temperature and alkaline hydroxide treatment effects on the surface area and pore structure of the cathode deposit multi-walled carbon nanotube (MWCNT)–graphite mixture were investigated in a temperature range of 600–800 °C. Hydrogen sorption properties of the MWCNT–graphite mixture samples were studied by varying the alkaline hydroxide-activation temperature. Pore characterization of modified MWCNT–graphite mixture was performed with the observation of adsorption–desorption isotherms of N₂ at 77 K. Hydrogen sorption of the non-treated and treated MWCNT–graphite mixture was carried out using a volumetric apparatus at 77 K. The highest surface area of the sample was obtained as 275 m² g^?1 by treatments with KOH at 600 °C. The increase in the specific surface area of MWCNT–graphite sample mixture was about 13 times. The maximum amount of hydrogen adsorbed on the MWCNT–graphite sample mixture was found as 0.75 and 0.54 wt.% by chemical treatments with KOH at 600 °C and NaOH at 700 °C, respectively whereas it was 0.01 wt.% for the original sample. The hydrogen sorption capacity was enhanced considerably by KOH treatments at 600 °C.     

LaNiO3 nanopowder prepared by an ‘amorphous citrate’ route

Aqueous solution techniques are simple and easy to use technological methods for preparing single-phase ceramic powders with controlled and homogeneous grain size. This study presents the preparation of ferroelectric LaNiO₃ ceramic samples by a gel-method using low sintering temperatures and the evolution of the amorphous complex and LaNiO₃ nanocrystallites with temperature.Ferroelectric LaNiO₃ powders were prepared using an ‘amorphous citrate’ route. X-ray diffraction, Raman scattering and electron microscopy techniques were used to characterize the obtained products after thermal treatments at between 550 and 750 °C and revealed the formation of LaNiO₃ nanocrystallites of perovskite structure with homogeneous grain size after thermal treatment at 650, 700 and 750 °C, with particle sizes of ∼30, 42 and 65 nm, respectively. Raman spectra exhibit the characteristic band of the LaNiO₃ perovskite-phase at 392 cm⁻¹ and decreasing band width with temperature, an effect associated to the observed change in grain size.     

Synthesizing carbon nanotubes and carbon nanofibers over supported-nickel oxide catalysts via catalytic decomposition of methane

Supported-NiO catalysts were tested in the synthesis of carbon nanotubes and carbon nanofibers by catalytic decomposition of methane at 550 °C and 700 °C. Catalytic activity was characterized by the conversion levels of methane and the amount of carbons accumulated on the catalysts. Selectivity of carbon nanotubes and carbon nanofiber formation were determined using transmission electron microscopy (TEM). The catalytic performance of the supported-NiO catalysts and the types of filamentous carbons produced were discussed based on the X-ray diffraction (XRD) results and the TEM images of the used catalysts. The experimental results show that the catalytic performance of supported-NiO catalysts decreased in the order of NiO/SiO₂ > NiO/HZSM-5 > NiO/CeO₂ > NiO/Al₂O₃ at both reaction temperatures. The structures of the carbons formed by decomposition of methane were dependent on the types of catalyst supports used and the reaction temperatures conducted. It was found that Al₂O₃ was crucial to the dispersion of smaller NiO crystallites, which gave rise to the formation of multi-walled carbon nanotubes at the reaction temperature of 550 °C and a mixture of multi-walled carbon nanotubes and single-walled carbon nanotubes at 700 °C. Other than NiO/Al₂O₃ catalyst, all the tested supported-NiO catalysts formed carbon nanofibers at 550 °C and multi-walled carbon nanotubes at 700 °C except for NiO/HZSM-5 catalyst, which grew carbon nanofibers at both 550 °C and 700 °C.     

Catalytic hydrogen transfer of ketones over atomic layer deposited highly-dispersed platinum nanoparticles supported on multi-walled carbon nanotubes

Hydrogen transfer of ketones, catalyzed by highly-dispersed platinum nanoparticles supported on multi-walled carbon nanotubes (MWCNTs), was studied. Pt nanoparticles were deposited on gram quantities of non-functionalized MWCNTs by atomic layer deposition (ALD) at 300 °C, using (methylcyclopentadienyl) trimethylplatinum and oxygen as precursors. TEM analysis showed that ~ 1.4 nm Pt nanoparticles were highly dispersed on MWCNTs. The heterogeneous hydrogen-transfer reactions of acetophenone indicated that an acetophenone conversion of 100% and a 1-phenylethanol selectivity of 99.0% could be obtained with a ketone to Pt mass ratio of 24,690 and a ketone to KOH mass ratio of 22 at 150 °C for 5 h. The selectivity of the Pt/MWCNT catalyst was higher than that of the commercial Pt/C catalyst, due to the highly-dispersed, uniform Pt nanoparticles and the unique porous structures of the Pt/MWCNT catalyst. The high stability of the Pt/MWCNT catalyst was demonstrated by reutilization of the catalyst. The high reactivity and selectivity of this catalyst for hydrogen transfer reduction were also demonstrated for other ketones.     

Solution-based fabrication and electrical properties of CaBi4Ti4O15 thin films

Ferroelectric CaBi₄Ti₄O₁₅ (CBT) thin films were prepared by spin coating technology using solution-based fabrication. The as-deposited CBT thin films were crystallized below 600 °C and the layered perovskite were crystallized at 700 °C using CFA processing in air. The enhancement of ferroelectric properties in CBT thin films for MFIS structures were investigated and discussed. Compared the Bi₄Ti₃O₁₂ (BIT), the CBT showed the better physical and electrical characteristics. The 700 °C annealed CBT thin films on SiO₂/Si substrate showed random orientation and exhibited large memory window curves. The maximum capacitance, memory window and leakage current density were about 250 pF, 2 V, and 10^?5 A/cm², respectively.     

Investigation of Li5Cr7Ti6O25 as novel anode material for high-power lithium-ion batteries

In this work, Li₅Cr₇Ti₆O₂₅ as a new anode material for rechargeable batteries is fabricated through a simple sol-gel method at different calcination temperatures. The X-ray diffraction, scanning electron microscopy, high resolution transmission electron microscopy, charge/discharge curve and cyclic voltammograms are utilized to study the crystal structures, morphologies and electrochemical properties of as-obtained Li₅Cr₇Ti₆O₂₅ samples. The impact of calcination temperatures on morphologies and electrochemical properties of Li₅Cr₇Ti₆O₂₅ is discussed in detail. The test result shows that the 800 °C is a proper calcination temperature for Li₅Cr₇Ti₆O₂₅ with excellent electrochemical properties. Cycled at 200 mA g⁻¹, it displays a high initial reversible capacity of 146.6 mA h g⁻¹ and retains a considerable capacity of 130.8 mA h g⁻¹ after 300 cycles. Even cycled at large current density of 500 mA g⁻¹, the initial reversible capacity of 129.6 mA h g⁻¹ with the capacity retention of 88% after 300 cycles is achieved, which is obviously higher than that of Li₅Cr₇Ti₆O₂₅ prepared at 700 °C (80.5 mA h g⁻¹ and 68%) and 900 °C (98.4 mA h g⁻¹ and 80%). In addition, in-situ XRD analysis reveals that Li₅Cr₇Ti₆O₂₅ exhibits a reversible structural change during lithiation and delithiation processes. The above prominent electrochemical performance indicates the great potential of the Li₅Cr₇Ti₆O₂₅ obtained at 800 °C as anode material for rechargeable batteries.     

Evaluating the photocatalytic activity of Pt/TNT film catalyst

TiO₂ nanotubes (TNT) were prepared by a hydrothermal method from the commercially available TiO₂-P25. Five types of TNT were produced at different temperatures (120 °C, 130 °C, and 150 °C) and by using different reaction times (12 h, 24 h, and 30 h). The photocatalytic reactor that was used is a film catalytic reactor, in which the height of the catalyst is 1.0 mm. The BET and FESEM analysis results showed that TNT130-24 (130 °C, 24 h) and TNT150-12 (150 °C, 12 h) possessed well-formed tubular structures with a high specific surface area (282.9–316.7 m² g⁻¹) and large pore volumes (0.62–0.70 cm³ g⁻¹). However, TNT120-30 (120 °C, 30 h) presented the best photocatalytic activity upon CO removal due to the synergistic effect of TiO₂ nanotubes and TiO₂ particles. After the TNT catalysts were modified with Pt particles, the removal efficiency was in the order of Pt/TNT120-30>Pt/TNT130-24>Pt/P25. Pt/TNT120-30 showed 99% removal efficiency in a continuous photoreactor with a high space velocity of 1.79×10⁴ h⁻¹. The results of the TEM and DRS analyses confirmed that the Pt particles enhanced the photocatalytic reaction, which was attributed to the well-dispersed nature of the 1 nm nanoscaled Pt particles on the surfaces of the TNT catalysts, and narrowed the band gap from 3.22 eV to 3.01 eV.     

The synthesis of a hybrid graphene–nickel/manganese mixed oxide and its performance in lithium-ion batteries

Mixing of aqueous suspensions of delaminated NiMn layered double hydroxide (LDH) and graphene oxide leads to the instantaneous precipitation of a hybrid material that after calcination under inert atmosphere at 450 °C leads to Ni₆MnO₈ nanoparticles deposited on larger reconstituted graphene sheets. This material exhibits electrical conductivity similar to graphite, superparamagnetism and can be used as an anode for Li-ion batteries. A maximum capacity value of 1030 mA h g^?1 was found during the first discharge, and capacity values higher than 400 mA h g^?1 were still achieved after 10 cycles. The methodology used here should allow the preparation of a large variety of hybrid graphene-metal oxide materials starting from other LDHs in which the properties derived from both constituents coexist.     

Preparation and characterization of BaCe0.95Tb0.05O3−α hollow fibre membranes for hydrogen permeation

BaCe_0.95Tb_0.05O_3?α (BCTb) perovskite hollow fibre membranes were fabricated by spinning the slurry mixture containing 66.67 wt% BCTb powder, 6.67 wt% polyethersulphone (PESf) and 26.67 wt% N-methyl-2-pyrrolidone (NMP) followed by sintering at elevated temperatures. The influence of sintering temperature on the membrane properties was investigated in terms of crystal phase, morphology, porosity and mechanical strength. In order to obtain gas-tight hollow fibres with sufficient mechanical strength, the sintering temperature should be controlled between 1350 and 1450 °C. Hydrogen permeation through the BCTb hollow fibre membranes was carried out between 700 and 1000 °C using 50% H₂–He mixture as feed on the shell side and N₂ as sweep gas in the fibre lumen. The measured hydrogen permeation flux through the BCTb hollow fibre membranes reached up to 0.422 μmol cm^?2 s^?1 at 1000 °C when the flow rates of the H₂–He feed and the nitrogen sweep were 40 mL min^?1 and 30 mL min^?1, respectively.     

Evaluation of the La0.75Sr0.25Mn0.8Co0.2O3−δ system as cathode material for ITSOFCs with La9Sr1Si6O26.5 apatite as electrolyte

In the past years, a major interest has been devoted to decrease the working temperature of solid oxide fuel cells (SOFCs) down to about 700 °C.Apatite materials (La_10?xSr_xSi₆O_27?x/2) are attractive candidates for solid electrolytes, with a high ionic conductivity at 700 °C, a chemical and a dimensional stability for a pO₂ ranging from 10^?25 to 0.2 atm. A perovskite oxide (La_0.75Sr_0.25Mn_0.8Co_0.2O_3?δ) has been used as a cathode material.Symmetrical cathode/electrolyte/cathode cells were fabricated by stacking layers obtained by tape casting of apatite and perovskite powders and co-sintering at 1400 °C for 2 h in air.Impedance spectroscopy measurements were performed on these cells in order to determine the electrode resistance. It has been shown that the latter decreases with the porosity content of the cathode and with the use of a composite material (apatite/perovskite) instead of a simple perovskite.     

Synthesis of high purity narrow-width carbon nanotubes

We have succeeded in controlling the width of multi-walled carbon nanotubes (MWCNT) by physical manipulation and pretreatment of the catalyst prior to reaction in a CO/H₂ reactant mixture. Since the size of the metal catalyst particle determines the width of the nanotube, we have investigated the notion of introducing a dispersing agent into the catalyst formulation that facilitates fragmentation and prevents sintering of the granules during the reduction step. Inclusion of 5 wt.% silica into a Fe–Ni (6:4) catalyst was found to reduce the average width of MWCNT from about 40 to 20 nm, when the bimetallic was reacted in CO/H₂ (1:4) at 670 °C. On the other hand, when 5 wt.% NaCl was used as the dispersant the average width of the MWCNT was decreased to about 11 nm. The impact of both the catalyst pre-treatment and various post-treatment procedures on the width and purity of the final MWCNT product is discussed.     

Development of PLZT dielectrics on base metal foils for embedded capacitors

We have deposited Pb_0.92La_0.08Zr_0.52Ti_0.48O₃ (PLZT) films on nickel and copper substrates to create film-on-foil capacitors that exhibit excellent dielectric properties and superior breakdown strength. Measurements with PLZT films on LaNiO₃-buffered Ni foils yielded the following: relative permittivity of 1300 (at 25 °C) and 1800 (at 150 °C), leakage current density of 6.6 × 10^?9 A/cm² (at 25 °C) and 1.4 × 10^?8 A/cm² (at 150 °C), and mean breakdown field strength ≈2.5 MV/cm. With PLZT deposited directly on Cu foils, we observed dielectric constant ≈1100, dielectric loss (tan δ) ≈0.06, and leakage current density of 7.3 × 10^?9 A/cm² when measured at room temperature.     

Synthesis of Na2FePO4F/C and its electrochemical performance

Using NaF as the only Na precursor, fluorophosphate Na₂FePO₄F/C materials have been synthesized via the solid-state reaction. Na₂FePO₄F starts to form at 300 °C, becomes the sole crystalline form between 400 and 600 °C, and decomposes at 650 °C. Comparing with the theoretical capacity of 124 mAh g^?1, the sample prepared at 600 °C delivered a discharge capacity of 118 mAh g^?1. The outstanding electrochemical performance is believed to result from the good crystallization and high purity of the synthesized materials. The capacity retentions at 0.5 C and 2 C are 95.8% and 89.8%, respectively, of that at 0.05 C. Furthermore, a discharge capacity of 122 mAh g^?1 is maintained under the cycling between 2.0 and 5.2 V vs. Li/Li⁺, indicating that the second Na⁺ is not extracted from the Na₂FePO₄F lattice.     

Ce0.9Gd0.1O1.95 supported La0.6Sr0.4Co0.2Fe0.8O3−δ cathodes for solid oxide fuel cells

Lanthanum-based iron- and cobalt-containing perovskite has a high potential as a cathode material because of its high electro-catalytic activity at a relatively low operating temperature in solid oxide fuel cells (SOFCs) (600–800). To enhance the electro-catalytic reduction of oxidants on La_0.6Sr_0.4Co_0.2Fe_0.8O_3?δ (LSCF), Ga doped ceria (Ce_0.9Gd_0.1O_1.95, GDC) supported LSCF (15LSCF/GDC) is successfully fabricated using an impregnation method with a ratio of 15 wt% LSCF and 85 wt% GDC. The cathodic polarization resistances of 15LSCF/GDC are 0.015 Ω cm², 0.03 Ω cm², 0.11 Ω cm², and 0.37 Ω cm² at 800 °C, 750 °C, 700 °C, and 650 °C, respectively. The simply mixed composite cathode with LSCF and GDC of the same compositions shows 0.05 Ω cm², 0.2 Ω cm², 0.56 Ω cm², and 1.20 Ω cm² at 800 °C, 750 °C, 700 °C, and 650 °C, respectively. The fuel cell performance of the SOFC with 15LSCF/GDC shows maximum power densities of 1.45 W cm^?2, 1.2 W cm^?2, and 0.8 W cm^?2 at 780 °C, 730 °C, and 680 °C, respectively. GDC supported LSCF (15LSCF/GDC) shows a higher fuel cell performance with small compositions of LSCF due to the extension of triple phase boundaries and effective building of an electronic path.     

Template-assisted synthesis of PbTiO3 nanotubes

Nanotubes of ferroelectric lead titanate (PbTiO₃) have been made by a template-assisted method. An equimolar Pb–Ti sol was dropped onto porous alumina membranes and penetrated into the channels of the template. Single-phase PbTiO₃ perovskite nanotubes were obtained by annealing at 700 °C for 6 h. The nanotubes had diameters of 200–400 nm with a wall thickness of approximately 20 nm. Excess PbO or annealing in a Pb-containing atmosphere was not necessary in order to achieve single-phase PbTiO₃ nanotubes. The influence of the heating procedure and the sol concentration is discussed.     

Deposition of highly oriented lanthanum nickel oxide thin film on silicon wafer by CSD

This paper describes the orientation control and the electrical properties of the chemical solution deposition (CSD) derived LaNiO₃ (LNO) thin film. The LNO precursor solutions were prepared using lanthanum nitrate and nickel acetate as La and Ni source, and ethanol or 2-methoxyethanol and 2-aminoethanol mixed solution as solvents. The LNO films were spin-coated using these precursor solutions and annealed at the temperature from 500 to 700 °C. The resulting LNO film annealed at 700 °C derived from 2-methoxyethanol and 2-aminoethanol mixed solvent exhibited (1 0 0)-orientation, with some surface cracks and pores, and relatively higher resistivity of 2.49 × 10⁻³ Ω cm. The LNO film derived from 2-methoxyethanol and 2-aminoethanol mixed solvent annealed at 700 °C in an oxygen atmosphere showed highly (1 0 0)-orientation, with higher density, a few cracks and pores, and exhibited a good electrical resistivity of 7.27 × 10⁻⁴ Ω cm.     

SrCo0.9Sc0.1O3−δ perovskite hollow fibre membranes for air separation at intermediate temperatures

SrCo_0.9Sc_0.1O₃ (SCSc) perovskite powders with sub-micron particle size were synthesized by a modified Pechini method combined with a post-treatment of sintering and ball-milling. From the prepared powders, the SCSc hollow fibre membranes with asymmetric structure and gas-tight property were fabricated by spinning a polymer solution containing 58.4 wt% SCSc followed by sintering at 1200 °C for 5 h. The oxygen permeation properties of the obtained SCSc fibres were measured under air/He gradients at 500–800 °C. This showed the oxygen flux of 1 mL cm^?2 min^?1 at 750 °C and 4.41 mL cm^?2 min^?1 at 900 °C. Modeling analysis reveals that the oxygen permeation process is predominated by oxygen surface exchange kinetics with an activation energy of 95.0 kJ mol^?1. The SCSc membranes showed excellent oxygen permeation performance while exhibiting high structural and permeating stability at intermediate temperatures (500–800 °C).     

Characteristics of highly (001) oriented (K,Na)NbO3 films grown on LaNiO3 bottom electrodes by RF magnetron sputtering

(K,Na)NbO₃ ferroelectric films were grown on LaNiO₃ coated silicon substrates by RF magnetron sputtering. The conductive LaNiO₃ films acted as seed layers and induced the highly (001) oriented perovskite (K,Na)NbO₃ films. Such films exhibit saturated hysteresis loops and have a remnant polarization (2P_r) of 23 μC/cm², and coercive field (2E_c) of 139 kV/cm. The films showed a fatigue-free behavior up to 10⁹ switching cycles. A high tunability of 65.7% (@300 kV/cm) was obtained in the films. The leakage current density of the films is about 6.0×10^?8 A/cm² at an electric field of 50 kV/cm.     

High glass transition temperature bio-based copolyesters from poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and isosorbide

New renewable copolymers were prepared from reactive bis-hydroxylated poly(3-hydroxybutyrate-co-3-hydroxyvalerate) oligomers (PHBHV-diol), isosorbide and 1,4-phenylene diisocyanate. First, microwave (MW)-assisted alcoholysis in the presence of ethylene glycol provides a rapid and straightforward method for engineering PHBHV-diol, with molar masses ranging from 700 to 4100 g mol^?1. These well-defined oligoesters were further used for the preparation of random copolymers of PHBHV-diol and isosorbide bridged with 1,4-phenylene diisocyanate via urethanization. The molar masses (M_n) of most copolyesters are about 10,000 g mol^?1 with polydispersities (DPI) in the range of 1.2–1.9. The dependence of the solid-state structures on the length of PHBHV block was carefully investigated. The incorporation of isosorbide units into the PHBHV backbone increased the glass-transition temperatures from +5 °C up to +34 °C.     

Studies on spinel cobaltites,MCo2O4 (M = Mn,Zn, Fe,Ni and Co) and their functional properties

Optimization of electrodes for charge storage with appropriate processing conditions places significant challenges in the developments for high performance charge storage devices. In this article, metal cobaltite spinels of formula MCo₂O₄ (where M = Mn, Zn, Fe, Ni and Co) are synthesized by oxalate decomposition method followed by calcination at three typical temperatures, viz. 350, 550, and 750 °C and examined their performance variation when used as anodes in lithium ion batteries. Phase and structure of the materials are studied by powder x-ray diffraction (XRD) technique. Single phase MnCo2O4,ZnCo2O4 and Co3O4 are obtained for all different temperatures 350 °C, 550 °C and 750 °C; whereas FeCo₂O₄ and NiCo₂O₄ contained their constituent binary phases even after repeated calcination. Morphologies of the materials are studied via scanning electron microscopy (SEM): needle-shaped particles of MnCo₂O₄ and ZnCo₂O₄, submicron sized particles of FeCo₂O₄ and agglomerated submicron particle of NiCo₂O₄ are observed. Galvanostatic cycling has been conducted in the voltage range 0.005–3.0 V vs. Li at a current density of 60 mA g^?1 up to 50 cycles to study their Li storage capabilities. Highest observed charge capacities are: MnCo₂O₄ – 365 mA h g^?1 (750 °C); ZnCo₂O₄ – 516 mA h g^?1 (550 °C); FeCo₂O₄ – 480 mA h g^?1 (550 °C); NiCo₂O₄ – 384 mA h g^?1 (750 °C); and Co₃O₄ – 675 mA h g^?1 (350 °C). The Co₃O₄ showed the highest reversible capacity of 675 mA h g^?1; the NiO present in NiCo₂O₄ acts as a buffer layer that results in improved cycling stability; the ZnCo₂O₄ with long needle-like shows good cycling stability.