Enhanced cycling performance of Fe3O4-graphene nanocomposite as an anode material for lithium-ion batteries

Fe₃O₄-graphene nanocomposite was prepared by a gas/liquid interface reaction. The structure and morphology of the Fe₃O₄-graphene nanocomposite were characterized by X-ray diffraction, scanning electron microscopy and high-resolution transmission electron microscopy. The electrochemical performances were evaluated in coin-type cells. Electrochemical tests show that the Fe₃O₄-22.7 wt.% graphene nanocomposite exhibits much higher capacity retention with a large reversible specific capacity of 1048 mAh g⁻¹ (99% of the initial reversible specific capacity) at the 90th cycle in comparison with that of the bare Fe₃O₄ nanoparticles (only 226 mAh g⁻¹ at the 34th cycle). The enhanced cycling performance can be attributed to the facts that the graphene sheets distributed between the Fe₃O₄ nanoparticles can prevent the aggregation of the Fe₃O₄ nanoparticles, and the Fe₃O₄-graphene nanocomposite can provide buffering spaces against the volume changes of Fe₃O₄ nanoparticles during electrochemical cycling.     

Structure and electrochemical performance of nanostructured Fe3O4/carbon nanotube composites as anodes for lithium ion batteries

Polyvinyl alcohol (PVA) was used as a hydrogen bond functionalizing agent to modify multi-walled carbon nanotubes (CNTs). Nanoparticles of Fe₃O₄ were then formed along the sidewalls of the as-modified CNTs by the chemical coprecipitation of Fe²⁺ and Fe³⁺ in the presence of CNTs in an alkaline solution. The structure and electrochemical performance of the Fe₃O₄/CNTs nanocomposite electrodes have been investigated in detail. Electrochemical tests indicated that at the 145th cycle, the CNTs-66.7 wt.%Fe₃O₄ nanocomposite electrode can deliver a high discharge capacity of 656 mAh g⁻¹ and stable cyclic retention. The improvement of reversible capacity and cyclic performance of the Fe₃O₄/CNTs nanocomposite could be attributed to the nanosized Fe₃O₄ particles and the network of CNTs.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Electrochemical characterization of amorphous LiFe(WO4)2 thin films as positive electrodes for rechargeable lithium batteries

Amorphous LiFe(WO₄)₂ thin films have been fabricated by radio-frequency (R.F.) sputtering deposition at room temperature. The as-deposited and electrochemically cycled thin films are, respectively, characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, selected area electron diffraction, and X-ray photoelectron spectra techniques. An initial discharge capacity of 198 mAh/g in Li/LiFe(WO₄)₂ cells is obtained, and the electrochemical behavior is mostly preserved in the following cycling. These results identified the electrochemical reactivity of two redox couples, Fe³⁺/Fe²⁺ and W⁶⁺/W^x+ (x = 4 or 5). The kinetic parameters and chemical diffusion coefficients of Li intercalation/deintercalation are estimated by cyclic voltammetry and alternate-current (AC) impedance measurements. All-solid-state thin film lithium batteries with Li/LiPON/LiFe(WO₄)₂ layers are fabricated and show high capacity of 104 μAh/cm² μm in the first discharge. As-deposited LiFe(WO₄)₂ thin film is expected to be a promising positive electrode material for future rechargeable thin film batteries due to its large volumetric rate capacity, low-temperature fabrication and good electrode/electrolyte interface.     

Structure and electrochemical properties of nanocarbon-coated Li3V2(PO4)3 prepared by sol-gel method

A liquid-based sol-gel method was developed to synthesize nanocarbon-coated Li₃V₂(PO₄)₃. The products were characterized by XRD, SEM and electrochemical measurements. The results of Rietveld refinement analysis indicate that single-phase Li₃V₂(PO₄)₃ with monoclinic structure can be obtained in our experimental process. The discharge capacity of carbon-coated Li₃V₂(PO₄)₃ was 152.6 mAh/g at the 50th cycle under 1C rate, with 95.4% retention rate of initial capacity. A high discharge capacity of 184.1 mAh/g can be obtained under 0.12C rate, and a capacity of 140.0 mAh/g can still be held at 3C rate. The cyclic voltammetric measurements indicate that the electrode reaction reversibility is enhanced due to the carbon-coating. SEM images show that the reduced particle size and well-dispersed carbon-coating can be responsible for the good electrochemical performance obtained in our experiments.     

Effect of TiO2 supporting layer on Fe2O3 photoanode for efficient water splitting

For an electrochemical water splitting system, titanate nanotubular particles with a thickness of ∼700 nm produced by a hydrothermal process were repetitively coated on fluorine-doped tin oxide (FTO) glass via layer-by-layer self-assembly method. The obtained titanate/FTO films were dipped in aqueous Fe solution, followed by heat treatment for crystallization at 500 °C for 10 min in air. The UV–vis absorbance of the Fe-oxide/titanate/FTO film showed a red-shifted spectrum compared with the TiO₂/FTO coated film; this red shift was achieved by the formation of thin hematite-Fe₂O₃ and anatase-TiO₂ phases verified using X-ray diffraction and Raman results. The cyclic voltammetry results of the Fe₂O₃/TiO₂/FTO films showed distinct reversible cycle characteristics with large oxidation–reduction peaks with low onset voltage of I–V characteristics under UV–vis light illumination. The prepared Fe₂O₃/TiO₂/FTO film showed much higher photocurrent densities for more efficient water splitting under UV–vis light illumination than did the Fe₂O₃/FTO film. Its maximum photocurrent was almost 3.5 times higher than that obtained with Fe₂O₃/FTO film because of the easy electron collection in the current collector. The large current collection was due to the existence of a TiO₂ base layer beneath the Fe₂O₃ layer.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Electrochemistry of V2ON with lithium

V₂ON thin film has been successfully fabricated by reactive dc sputtering method and annealing process and was investigated for its electrochemistry with lithium. The reversible discharge capacities of V₂ON/Li cells cycled between 0.01 and 4.0 V were found in the range of 803–915 mAh g⁻¹ during the first 50 cycles. By using ex situ scanning electron microscopy, transmission electron microscopy, selected-area electron diffraction and X-ray photoelectron spectroscopy measurements, the reversible transformation between nanocrystalline V₂ON and well dispersed V, Li₂O, Li₃N nano-composites were revealed in the lithium electrochemical reaction. V₂ON thin film exhibits high reversible capacity and good cycle performance with remarkable lower polarization than VN thin film.     

Preparation and cycling performance of Aland F co-substituted compounds Li4AlxTi5−xFyO12−y

Li₄Al_xTi_5−xF_yO_12−y compounds were prepared by a solid-state reaction method. Phase analyses demonstrated that both Al³⁺ and F⁻ ions entered the structure of spinel-type Li₄Ti₅O₁₂. Charge-discharge cycling results at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.5 and 0.5 V showed that the Al³⁺ and F⁻ substitutions improved the first total discharge capacity of Li₄Ti₅O₁₂. However, Al³⁺ substitution greatly increased the reversible capacity and cycling stability of Li₄Ti₅O₁₂ while F⁻ substitution decreased its reversible capacity and cycling stability slightly. The electrochemical performance of the Al³⁺-F⁻-co-substituted specimen was better than the F⁻-substituted one but worse than the Al³⁺-substituted one.     

Synthesis of LiNi0.9Co0.1O2 from Li2CO3, NiO or NiCO3, and CoCO3 or Co3O4 and their electrochemical properties

Cathode active materials with a composition of LiNi_0.9Co_0.1O₂ were synthesized by a solid-state reaction method at 850 °C using Li₂CO₃, NiO or NiCO₃, and CoCO₃ or Co₃O₄, as the sources of Li, Ni, and Co, respectively. Electrochemical properties, structure, and microstructure of the synthesized LiNi_0.9Co_0.1O₂ samples were analyzed. The curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂ for the first charge–discharge and the intercalated and deintercalated Li quantity Δx were studied. The destruction of unstable 3b sites and phase transitions were discussed from the first and second charge–discharge curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂. The LiNi_0.9Co_0.1O₂ sample synthesized from Li₂CO₃, NiO, and Co₃O₄ had the largest first discharge capacity (151 mA h/g), with a discharge capacity deterioration rate of −0.8 mA h/g/cycle (that is, a discharge capacity increasing 0.8 mA h/g per cycle).     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

A promising sol-gel route based on citric acid to synthesize Li3V2(PO4)3/carbon composite material for lithium ion batteries

Li₃V₂(PO₄)₃/carbon composite material was synthesized by a promising sol-gel route based on citric acid using V₂O₅ powder as a vanadium source. Citric acid acts not only as a chelating reagent but also as a carbon source, which enhance the conductivity of the composite material and hinder the growth of Li₃V₂(PO₄)₃ particles. The structure and morphology of the sample were characterized by TG, XRD and TEM measurements. XRD results reveal that Li₃V₂(PO₄)₃/carbon was successfully synthesized and has a monoclinic structure with space group P2₁/n. TEM images show Li₃V₂(PO₄)₃ particles are about 45 nm in diameter embeded in carbon networks. Galvanostatic charge/discharge and cyclic voltammetry measurements were used to study its electrochemical behaviors which indicate the reversibility of the lithium extraction/insertion processes. Li₃V₂(PO₄)₃/carbon performed in a voltage window (3.0-4.8 V) exhibits higher discharge capacity, better cycling stability and its discharge capacity maintains about 167.6 mAh/g at a current density of 28 mA/g after 50 cycles.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Optimum synthesis of Li2Fe1−xMnxSiO4/C cathode for lithium ion batteries

Li₂Fe_1−xMn_xSi0₄/C cathode materials were synthesized by mechanical activation-solid-state reaction. The effects of Mn-doping content, roasting temperature, soaking time and Li/Si molar ratio on the physical properties and electrochemical performance of the Li₂Fe_1−xMn_xSi0₄/C composites were investigated. The materials were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM), charge-discharge tests and AC impedance measurements. SEM images suggest that the morphology of the Li₂Fe_1−xMn_xSi0₄/C composite is sensitive to the reaction temperature. Samples synthesized at different temperatures have different extent of agglomeration. Being charged-discharged at C/32 between 1.5 and 4.8 V, the Li₂Fe_0.9Mn_0.1Si0₄/C synthesized at the optimum conditions shows good electrochemical performances with an initial discharge capacity of 158.1 mAh g⁻¹ and a capacity retention ratio of 94.3% after 30 cycles. AC impendence investigation shows Li₂Fe_0.9Mn_0.1SiO₄/C have much lower resistance of electrode/electrolyte interface than Li₂FeSiO₄/C.     

Pulsed laser deposited FeOF as negative electrodes for rechargeable Li batteries

FeOF thin film has been successfully fabricated by reactive pulsed laser deposition for the first time, and its electrochemical behavior was examined as a negative electrode active material in lithium-ion batteries. The electrochemical properties of the as-deposited FeOF thin film during the first charging and discharging have been investigated by the galvanostatic cycling and cyclic voltammetry measurements. By using ex situ X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected-area electron diffraction measurements (SAED), it can be found that FeOF was initially decomposed into Fe⁰, LiF, and Fe₂O₃ after discharging to 1.0 V. The newly formed Fe₂O₃ is then subsequently reduced into Li₂O and Fe⁰ after further discharging to 0.01 V. In the subsequent cycle, the reduction peaks at 0.76 V and the oxidation-reduction peaks at 1.6 and 1.9 V could be attributed to the reversible decomposition and formation of Li₂O with the conversion reaction of Fe₂O₃ into Fe.     

The influence of preparation conditions on electrochemical properties of LiNi0.5Mn1.5O4 thin film electrodes by PLD

LiNi_0.5Mn_1.5O₄ thin films were prepared by pulsed laser deposition (PLD) on stainless steel substrates. The growth of the films has been studied as a function of substrate temperature and oxygen partial pressure in deposition, using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). Electrochemical properties of LiNi_0.5Mn_1.5O₄ thin film cathodes were investigated using cyclic voltammetry and galvanostatic charge/discharge against a lithium anode. The initial capacity and capacity retention of the films are highly dependent on the crystallinity and purity of the films. LiNi_0.5Mn_1.5O₄ thin films grown at 600 °C in an oxygen partial pressure of 200 mTorr are well crystallized with high purity, exhibiting excellent capacity retention between 3 and 5 V with a LiPF₆-based electrolyte.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 cathode materials by using a supercritical water method in a batch reactor

LiNi_1/3Co_1/3Mn_1/3O₂ and LiCoO₂ cathode materials were synthesized by using a supercritical water (SCW) method with a metal salt solution in a batch reactor. Stoichiometric LiNi_1/3Co_1/3Mn_1/3O₂ was successfully synthesized in a 10-min reaction without calcination, while overlithiated LiCoO₂ (Li_1.15CoO₂) was synthesized using the batch SCW method. The physical properties and electrochemical performances of LiNi_1/3Co_1/3Mn_1/3O₂ were compared to those of Li_1.15CoO₂ by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and charge/discharge cycling tests. The XRD pattern of LiNi_1/3Co_1/3Mn_1/3O₂ was found to be similar to that of Li_1.15CoO₂, showing clear splitting of the (0 0 6)/(1 0 2) and (1 0 8)/(1 1 0) peak pairs as particular characteristics of the layered structure. In addition, both cathode powders showed good crystallinity and phase purity, even though a short reaction time without calcination was applied to the SCW method. The initial specific discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders at a current density of 0.24 mA/cm² in 2.5-4.5 V were 149 and 180 mAh/g, and their irreversible capacity loss was 20 and 17 mAh/g, respectively. The discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders decreased with cycling and remained at 108 and 154 mAh/g after 30 cycles, which are 79% and 89% of the initial capacities. Compared to the overlithiated LiCoO₂ cathode powders, the LiNi_1/3Co_1/3Mn_1/3O₂ cathode powders synthesized by SCW method had better electrochemical performances.     

Preparation and characterization of ramsdellite Li2Ti3O7 as an anode material for asymmetric supercapacitors

Ramsdellite Li₂Ti₃O₇ was first synthesized via sol-gel process with good crystallity of an average particle size of 0.175 μm. The product was thoroughly investigated as a lithium intercalation compound, and as an active anode material in asymmetric supercapacitors coupling with activated carbon as cathode. Lithium intercalation reactions were found occurring at 1.32 and 1.62 V versus Li/Li⁺, respectively. A reversible specific capacity of 150 mA h g⁻¹ at 1C was obtained on Li₂Ti₃O₇ electrode in a nonaqueous electrolyte. The charge current was found to strongly influence the anodic discharge capacity in the asymmetric cell. The capacity retention at 10C charge-discharge rate was found to be 75.9% in comparison with that at 1C.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.