Attempts to reduce NOx exhaust emissions by using reformulated biodiesel

Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from diesel engines. Under some conditions, however, biodiesel produced from certain feedstocks has been shown to cause an increase in nitrogen oxides (NO_x). This is of special concern in urban areas that are subject to strict environmental regulations. Although soy-based biodiesel may increase the emission of nitrogen oxides, it is the most easily accessible in North America. We investigated two routes to reformulate soy-based biodiesel in an effort to reduce nitrogen oxide emissions. In one of these, soy-oil methyl esters were modified by conversion of a proportion of the cis bonds in the fatty acid chains of its methyl esters to their trans isomers. In the other approach, polyol derivatives of soybean oil were transesterified to form soy methyl polyol fatty acid esters. The NO_x emissions of these modified biodiesels were then examined, using a Yanmar L100 single cylinder, four stroke, naturally aspirated, air cooled, direct injection diesel engine. Using either isomerized methyl oleate or isomerized soy biodiesel, at 20% blend level in petroleum diesel (‘B20’), nitrogen oxide emissions were elevated by between 1.5 and 3 percentage points relative to the combustion of a B20 blend of commercial biodiesel. Nitrogen oxide emissions were reduced in proportion to blend level during the combustion of polyol biodiesel, with a 20% blend in petrodiesel resulting in a reduction of about 4.5 percentage points relative to the emissions of a comparable blend of commercial soy biodiesel.     

A numerical investigation into the anomalous slight NOx increase when burning biodiesel; A new (old) theory

Biodiesel is a notable alternative to petroleum derived diesel fuel because it comes from natural domestic sources and thus reduces dependence on diminishing petroleum fuel from foreign sources, it likely lowers lifecycle greenhouse gas emissions, and it lowers an engine's emission of most pollutants as compared to petroleum derived diesel. However, the use of biodiesel often slightly increases a diesel engine's emission of smog forming nitrogen oxides (NO_x) relative to petroleum diesel. In this paper, previously proposed theories for this slight NO_x increase are reviewed, including theories based on biodiesel's cetane number, which leads to differing amounts of charge preheating, and theories based on the fuel's bulk modulus, which affects injection timing. This paper proposes an additional theory for the slight NO_x increase of biodiesel. Biodiesel typically contains more double bonded molecules than petroleum derived diesel. These double bonded molecules have a slightly higher adiabatic flame temperature, which leads to the increase in NO_x production for biodiesel. Our theory was verified using numerical simulations to show a NO_x increase, due to the double bonded molecules, that is consistent with observation. Further, the details of these numerical simulations show that NO_x is predominantly due to the Zeldovich mechanism.     

Exhaust emissions from a diesel powered vehicle fuelled by soybean biodiesel blends (B3-B20) with ethanol as an additive (B20E2-B20E5)

The effects of diesel oil-soybean biodiesel blends on a passenger vehicle exhaust pollutant emissions were investigated. Blends of diesel oil and soybean biodiesel with concentrations of 3% (B3), 5% (B5), 10% (B10) and 20% (B20) were used as fuels. Additionally, the effects of anhydrous ethanol as an additive to B20 fuel blend with concentrations of 2% (B20E2) and 5% (B20E5) were also studied. The emissions tests were carried out following the New European Driving Cycle (NEDC). The results showed that increasing biodiesel concentration in the fuel blend increases carbon dioxide (CO₂) and oxides of nitrogen (NO_X) emissions, while carbon monoxide (CO), hydrocarbons (HC) and particulate matter (PM) emissions are reduced. The addition of anhydrous ethanol to B20 fuel blend proved it can be a strategy to control exhaust NO_X and global warming effects through the reduction of CO₂ concentration. However, it may require fuel injection modifications, as it increases CO, HC and PM emissions.     

Exhaust emissions and fuel properties of partially hydrogenated soybean oil methyl esters blended with ultra low sulfur diesel fuel

Important fuel properties and emission characteristics of blends (20 vol.%) of soybean oil methyl esters (SME) and partially hydrogenated SME (PHSME) in ultra low sulfur diesel fuel (ULSD) were determined and compared with neat ULSD. The following changes were observed for B20 blends of SME and PHSME versus neat ULSD: improved lubricity, higher kinematic viscosity and cetane number, lower sulfur content, and inferior low-temperature properties and oxidative stability. With respect to exhaust emissions, B20 blends of PHSME and SME exhibited lower PM and CO emissions in comparison to those of neat ULSD. The PHSME blend also showed a significant reduction in THC emissions. Both SME and PHSME B20 blends yielded small increases in NO_x emissions. The reduction in double bond content of PHSME did not result in a statistically significant difference in NO_x emissions versus SME at the B20 blend level. The test engine consumed a greater amount of fuel operating on the SME and PHSME blends than on neat ULSD, but the increase was smaller for the PHSME blend.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Mitigation of NOx emissions from a jatropha biodiesel fuelled DI diesel engine using antioxidant additives

Biodiesel offers cleaner combustion over conventional diesel fuel including reduced particulate matter, carbon monoxide and unburned hydrocarbon emissions. However, several studies point to slight increase in NO_x emissions (about 10%) for biodiesel fuel compared with conventional diesel fuel. Use of antioxidant additives is one of the most cost-effective ways to mitigate the formation of prompt NO_x. In this study, the effect of antioxidant additives on NO_x emissions in a jatropha methyl ester fuelled direct injection diesel engine have been investigated experimentally and compared. A survey of literature regarding the causes of biodiesel NO_x effect and control strategies is presented. The antioxidant additives L-ascorbic acid, α tocopherol acetate, butylated hydroxytoluene, p-phenylenediamine and ethylenediamine were tested on computerised Kirloskar-make 4 stroke water cooled single cylinder diesel engine of 4.4 kW rated power. Results showed that antioxidants considered in the present study are effective in controlling the NO_x emissions of biodiesel fuelled diesel engines. A 0.025%-m concentration of p-phenylenediamine additive was optimal as NO_x levels were substantially reduced in the whole load range in comparison with neat biodiesel. However, hydrocarbon and CO emissions were found to have increased by the addition of antioxidants.     

Emission characteristics using methyl soyate–ethanol–diesel fuel blends on a diesel engine

A blend of 20% (v/v) ethanol/methyl soyate was prepared and added to diesel fuel as an oxygenated additive at volume percent levels of 15 and 20% (denoted as BE15 and BE20). We also prepared a blend containing 20% methyl soyate in diesel fuel (denoted as B20). The fuel blends that did not have any other additive were stable for up to 3 months. Engine performance and emission characteristics of the three different fuels in a diesel engine were investigated and compared with the base diesel fuel. Observations showed that particulate matter (PM) emission decreased with increasing oxygenate content in the fuels but nitrogen oxides (NO_x) emissions increased. The diesel engine fueled by BE20 emitted significantly less PM and a lower Bosch smoke number but the highest NO_x among the fuel blends tested. All the oxygenate fuels produced moderately lower CO emissions relative to diesel fuel. The B20 blend emitted less total hydrocarbon (THC) emissions compared with base diesel fuel. This was opposite to the fuel blends containing ethanol (BE15, BE20), which produced much higher THC emission.     

Modeling effect of the biodiesel mixing ratio on combustion and emission characteristics using a reduced mechanism of methyl butanoate

This paper describes a modeling study on the effects of the mixing ratio of biodiesel derived from rice on combustion and emission characteristics. In order to model ignition and combustion processes, a combined mechanism of methyl butanoate and n-heptane was used after modifying some reaction constants. The oxygen content of rice oil was maintained at the measured value (11 vol.%) by assuming that one mole of rice oil was composed of one mole of methyl butanoate and two moles of n-heptane. The fuel property library of the KIVA code was expanded to include physical properties such as density and surface tension of rice oil (i.e., biodiesel). In addition, a discrete multi-component fuel evaporation model was employed to model the fuel injection, atomization, and evaporation.Calculated pressure histories and carbon monoxide (CO) and hydrocarbon (HC) emissions of the present study agreed reasonably with experiments at a 100 MPa injection pressure and a 10° BTDC injection timing for D100, BD20, and BD40. However some discrepancies were observed in predicting nitrogen oxide (NO_x) emissions. The effect of the start of injection timing on fuel consumption and CO emissions were also studied.     

Performance of compression ignition engine with mahua (Madhuca indica) biodiesel

The performance of biodiesel obtained from mahua oil and its blend with high speed diesel in a Ricardo E6 engine has been presented in this paper together with some of its fuel properties. These properties were found to be comparable to diesel and confirming to both the American and European standards. Engine performance (brake specific fuel consumption, brake thermal efficiency and exhaust gas temperature) and emissions (CO, smoke density and NO_x) were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The reductions in exhaust emissions and brake specific fuel consumption together with increase brake power, brake thermal efficiency made the blend of biodiesel (B20) a suitable alternative fuel for diesel and thus could help in controlling air pollution.     

Comparative evaluation of performance and emission characteristics of jatropha, karanja and polanga based biodiesel as fuel in a tractor engine

Non-edible jatropha (Jatropha curcas), karanja (Pongamia pinnata) and polanga (Calophyllum inophyllum) oil based methyl esters were produced and blended with conventional diesel having sulphur content less than 10 mg/kg. Ten fuel blends (Diesel, B20, B50 and B100) were tested for their use as substitute fuel for a water-cooled three cylinder tractor engine. Test data were generated under full/part throttle position for different engine speeds (1200, 1800 and 2200 rev/min). Change in exhaust emissions (Smoke, CO, HC, NO_x, and PM) were also analyzed for determining the optimum test fuel at various operating conditions. The maximum increase in power is observed for 50% jatropha biodiesel and diesel blend at rated speed. Brake specific fuel consumptions for all the biodiesel blends with diesel increases with blends and decreases with speed. There is a reduction in smoke for all the biodiesel and their blends when compared with diesel. Smoke emission reduces with blends and speeds during full throttle performance test.     

Real-time and robust estimation of biodiesel blends

Biodiesel as a renewable alternative fuel produces lower exhaust emissions with the exception of nitrogen oxides (NO_x) when compared to the conventional diesel fuel. Reducing nitrogen oxides produced from engines running on biodiesel requires proper engine controller adaptations that are linked to the specifics of the fuel blend. Therefore, online estimation of fuel blend is a critical step in allowing diesel engines to maintain performance while simultaneously meeting emission requirements when operating on biodiesel blends. Presented in this paper are three different model-based biodiesel blend estimation strategies using: (i) crankshaft torsionals, (ii) NO_x emissions measurement from the exhaust stream, and (iii) oxygen content measurement of the exhaust stream using a wide-band UEGO sensor. Each approach is investigated in terms of the accuracy and robustness to sensor errors. A sensitivity analysis is conducted for each method to quantify robustness of the proposed fuel blend estimation methods.     

Biodiesel engine performance and emissions in low temperature combustion

Engine performance and emission comparisons were made between the use of soy, Canola and yellow grease derived B100 biodiesel fuels and an ultra-low sulphur diesel fuel in the high load engine operating conditions. Compared to the diesel fuel engine-out emissions of nitrogen oxides (NO_x), a high-cetane number (CN) biodiesel fuel produced comparable NO_x while the biodiesel with a CN similar to the diesel fuel produced relatively higher NO_x at a fixed start of injection. The soot, carbon monoxide and un-burnt hydrocarbon emissions were generally lower for the biodiesel-fuelled engine. Exhaust gas recirculation (EGR) was then extensively applied to initiate low temperature combustion (LTC) mode at medium and low load conditions. An intake throttling valve was implemented to increase the differential pressure between the intake and exhaust in order to increase and enhance the EGR. Simultaneous reduction of NO_x and soot was achieved when the ignition delay was prolonged by more than 50% from the case with 0% EGR at low load conditions. Furthermore, a preliminary ignition delay correlation under the influence of EGR at steady-state conditions was developed. The correlation considered the fuel CN and oxygen concentrations in the intake air and fuel. The research intends to achieve simultaneous reductions of NO_x and soot emissions in modern production diesel engines when biodiesel is applied.     

Solubility of a diesel–biodiesel–ethanol blend,its fuel properties,and its emission characteristics from diesel engine

In this work, we studied the phase diagram of diesel–biodiesel–ethanol blends at different purities of ethanol and different temperatures. Fuel properties (such as density, heat of combustion, cetane number, flash point and pour point) of the selected blends and their emissions performance in a diesel engine were examined and compared to those of base diesel. It was found that the fuel properties were close to the standard limit for diesel fuel; however, the flash point of blends containing ethanol was quite different from that of conventional diesel. The high cetane value of biodiesel could compensate for the decrease of the cetane number of the blends caused by the presence of ethanol. The heating value of the blends containing lower than 10% ethanol was not significantly different from that of diesel. As for the emissions of the blends, it was found that CO and HC reduced significantly at high engine load, whereas NO_x increased, when compared to those of diesel. Taking these facts into account, a blend of 80% diesel, 15% biodiesel and 5% ethanol was the most suitable ratio for diesohol production because of the acceptable fuel properties (except flash point) and the reduction of emissions.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.     

Effect of biodiesel blends on North American heavy‐duty diesel engine emissions

We conducted an assessment of North American heavy‐duty engine emission test results for biodiesel from 49 experimental studies, including both engine dynamometer and vehicle test results. Comparison with a commercial database showed that the engines in the emissions database are not representative of the existing North American in‐use fleet as of 2007; more than 50% of the tested engines were of 1995 or earlier vintage. Nevertheless, the results show that the use of a common biodiesel blend (B20) consistently reduces emissions of particulate matter, hydrocarbons, and carbon monoxide by 10–20%. Tests with B20 show varying effects on oxides of nitrogen (NO_x). If results for pre‐1992 two‐cycle 6V‐92TA(E) engines (which represent 0.2% of the 2007 in‐use fleet but 28% of the engines tested) are removed, then there is no statistical evidence that the average NO_x emissions from B0 and B20 are different (p value of 0.50 for an estimated average increase of 1%). Several researchers have used changes in engine calibration to eliminate any NO_x penalty associated with B20 (in engines that show an increase in NO_x with B20), while still maintaining the advantages of B20 in reducing other pollutants. The emissions effect of B20 on heavy‐duty diesel truck emissions did not show any correlation with model year or type of fuel injection equipment.     

Experimental investigation on injection characteristics of bioethanol-diesel fuel and bioethanol-biodiesel blends

This paper analyses the fuel injection characteristics of bioethanol-diesel fuel and bioethanol-biodiesel blends considered as fuel for diesel engines. Attention is focused on the injection characteristics which significantly influence the engine characteristics and subsequently the exhaust emissions. In this context the following injection characteristics have been investigated experimentally: fuelling, injection timing, injection delay, injection duration, mean injection rate, and injection pressure. The tested fuels were neat mineral diesel fuel, neat biodiesel made from rapeseed oil, bioethanol/diesel fuel and bioethanol/biodiesel blends up to 15% (v/v) bioethanol with an increment of 5%. The fuels blends were experimentally investigated in a fuel injection M system at rated condition (FL, 1100 rpm), peak torque (FL, 850 rpm), and maximum pump speed (1100 rpm) for different partial loads (PL 75% and PL 50%), at ambient temperature.It has been proven that for all operating regimens tested, the addition of bioethanol to biodiesel reduces fuelling, injection timing, injection duration, mean injection rate and maximum injection pressure and increases injection delay compared to pure biodiesel. Meanwhile, increasing bioethanol in diesel fuel shows no significant variations or a slightly increase in fuelling, injection timing, injection duration, and mean injection rate and a decrease in injection delay and maximum injection pressure, compared to pure diesel fuel.The influence of bioethanol in biodiesel is much more significant that in diesel fuel; it has a beneficial effect on biodiesel injection characteristics because bioethanol addition brings them nearer to the diesel fuel one and it is expected to decrease biodiesel NO_x emissions.     

Engine performance and emission characteristics of marine fish-oil biodiesel produced from the discarded parts of marine fish

Biodiesel is recognized as a clean alternative fuel or as a fuel additive to reduce pollutant emissions from combustion equipment. Because cultivated land is too limited to grow seed-oil plants sufficient to produce both food and biodiesel, non-land-based oleaginous materials have been considered important sources for the production of the latter. In this study, the discarded parts of mixed marine fish species were used as the raw material to produce biodiesel. Marine fish oil was extracted from the discarded parts of mixed marine fish and refined through a series of pretreatment processes. The refined marine fish oil was then transesterified with methyl alcohol to produce biodiesel, which was used thereafter as engine fuel to investigate its engine performance and emission characteristics. The experimental results show that, compared with commercial biodiesel from waste cooking oil, marine fish-oil biodiesel has a larger gross heating value, elemental carbon and hydrogen content, cetane index, exhaust gas temperature, brake fuel conversion efficiency, NO_x and O₂ emissions, and black smoke opacity and a lower elemental oxygen content, fuel consumption rate, brake-specific fuel consumption rate, equivalence ratio, and CO emission. Compared with ASTM No. 2D diesel, both marine fish-oil and waste cooking-oil biodiesels appear to have a lower gross heating value, cetane index, exhaust gas temperature, equivalence ratio, black smoke opacity, elemental carbon content, and CO emission and a higher fuel consumption rate and elemental oxygen content.     

Experimental investigation of mineral diesel fuel, GTL fuel, RME and neat soybean and rapeseed oil combustion in a heavy duty on-road engine with exhaust gas aftertreatment

The effects of mineral diesel fuel, gas-to-liquid fuel, rapeseed methyl ester, neat soybean and neat rapeseed oil on injection, combustion, efficiency and pollutant emissions have been studied on a compression ignition heavy duty engine operated near full load and equipped with a combined exhaust gas aftertreatment system (oxidation catalyst, particle filter, selective catalytic NO_x reduction). In a first step, the engine calibration was kept constant for all fuels which led to differences in engine torque for the different fuels. In a second step, the injection duration was modified so that all fuels led to the same engine torque. In a third step, the engine was recalibrated in order to keep the NO_x emissions at an equal level for all fuels (injection pressure, injection timing, EGR rate). The experiments show that the critical NO_x emissions were higher (even behind the exhaust gas aftertreatment systems) for oxygenated fuels in case of the engine not being recalibrated for the fuel. GTL and the oxygenated fuels show lower emissions for some pollutants and higher efficiency after recalibration to equal NO_x levels.     

Engine performance and emission characteristics of a three-phase emulsion of biodiesel produced by peroxidation

Biodiesel, which is produced from vegetable oils, animal fats or used cooking oils, can be used as an alternative fuel for diesel engines. The high oxygen content of biodiesel not only enhances its burning efficiency, but also generally promotes the formation of more nitrogen oxides (NO_x) during the burning process. Fuel emulsification and the use of NO_x inhibitor agents in fuel are considered to be effective in reducing NO_x emissions. In the study reported herein, soybean oil was used as raw oil to produce biodiesel by transesterification reaction accompanied by peroxidation to further improve the fuel properties of the biodiesel, which was water washed and distilled to remove un-reacted methanol, water, and other impurities. The biodiesel product was then emulsified with distilled water and emulsifying surfactant by a high-speed mechanical homogenizer to produce a three-phase oil-droplets-in-water-droplets-in-oil (i.e. O/W/O) biodiesel emulsion and an O/W/O emulsion that contained aqueous ammonia, which is a NO_x inhibitor agent. A four-stroke diesel engine, in combination with an eddy-current dynamometer, was used to investigate the engine performance and emission characteristics of the biodiesel, the O/W/O biodiesel emulsion, the O/W/O biodiesel emulsion that contained aqueous ammonia, and ASTM No. 2D diesel. The experimental results show that the O/W/O emulsion has the lowest carbon dioxide (CO₂) emissions, exhaust gas temperature, and heating value, and the largest brake specific fuel consumption, fuel consumption rate, and kinematic viscosity of the four tested fuels. The increase of engine speed causes the increase of equivalence ratio, exhaust gas temperature, CO₂ emissions, fuel consumption rate, and brake specific fuel consumption, but a decrease of NO_x emissions. Moreover, the existence of aqueous ammonia in the O/W/O biodiesel emulsion curtails NO_x formation, thus resulting in the lowest NO_x emissions among the four tested fuels in burning the O/W/O biodiesel emulsion that contained aqueous ammonia.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.