Oxygen barrier,free volume,and blending properties of fully bio-based polyamide 11/poly(vinyl alcohol) blends

Fully bio-based polyamide 11 (PA11) was melt-blended with poly(vinyl alcohol) (PVA) with varying degrees of polymerization (DP) to prepare PA11_xPVA^z_y. The PA11_xPVA^z_y films demonstrated the lowest oxygen transmission rates (OTR) and free volume characteristics, when PVA contents of each PA11_xPVA^z_y series reached a corresponding critical concentration. The minimum OTR and free volume characteristics obtained for the optimal PA11_xPVA^z_y films reduced significantly with decreasing PVA DPs. The OTR of the optimal PA11_xPVA^z_y blown film was 1.07 cm³ m⁻² day⁻¹ atm⁻¹, which is near to that of the ethylene-vinyl alcohol copolymer high-barrier polymer. The results of dynamical, mechanical, and other experimental characterizations demonstrated that PA11 and PVA are compatible to some extent when PVA concentrations are less-than or equal to the respective critical values. The enhanced oxygen permeation resistance and free volume characteristics for optimal PA11_xPVA^z_y films are at least partly ascribed to the improved hydrogen-bonded molecular interactions between PA11 CO groups and PVA O─H groups. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48562.     

Properties of polyamide 612/poly(vinyl alcohol) blends and their impact on free volume and oxygen barrier properties

Oxygen transmission rates and free volume properties (i.e. average volumes of free-volume-cavities (V_f), mean number of the free volume cavities per unit volume (I₃) and fractional free volume (F_v)) values of bio-based polyamide 612 (PA612)/poly(vinyl alcohol) (PVA) (i.e. PA612_xPVA⁰³_y, PA612_xPVA⁰⁵_y, PA612_xPVA⁰⁸_y and PA612_xPVA¹⁴_y) blend films were reduced to a minimum value, when their PVA content reached corresponding optimal values of 25, 20, 15 and 10 wt%, respectively. The minimum oxygen transmission rate, V_f, I₃ and F_v value obtained for the best PA612₉₀PVA¹⁴₁₀, PA612₈₅PVA⁰⁸₁₅, PA612₈₀PVA⁰⁵₂₀ and PA612₇₅PVA⁰³₂₅ bio-based blown films reduced considerably with decreasing PVA degrees of polymerization. As evidenced by the results of dynamical mechanical analysis, differential scanning calorimetry, wide angle X-ray diffraction and Fourier transform infrared spectroscopic experiments, PA612 and PVA are miscible to some extent at the molecular level when their PVA contents are ≤ the corresponding optimal values. The significantly improved oxygen barrier and free volume properties for the PA612_xPVA^z_y blend films with optimized compositions is at least in part to the enhanced intermolecular interactions between PA612 carbonyl groups and PVA hydroxyl groups.     

The effect of poly(vinyl alcohol) hydrolysis on the properties of its blends with nylon 6

An investigation of the properties of the blends of nylon 6 (PA6) and poly(vinyl alcohol) (PVA) with varying degrees of hydrolysis was conducted. A near disappearance of the characteristics of the α‐form PVA crystals, crystallization exotherms, and hydrogen‐bonded hydroxyl groups and the tensile properties originally associated with the PVA molecules of PA6_xPVA PA6_xPVA, and PA6_xPVA specimens was observed as the PVA contents of the specimens became equal to or less than their corresponding ‘‘critical’’ values at 16.7 wt%, 33.3 wt%, and 50 wt%, respectively. These results support the idea that PVA molecules are miscible with PA6 molecules to some extent at the molecular level as the PVA contents of the blends become equal to or less than their corresponding critical PVA contents. In this article, we have proposed the possible reasons accounting for these properties of the PA6_xPVA_y series specimens with a varying degree of hydrolysis. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Evaluation of RuxWySez Catalyst as a Cathode Electrode in a Polymer Electrolyte Membrane Fuel Cell

The oxygen reduction reaction (ORR) on Ru_xW_ySe_z is of great importance in the development of a novel cathode electrode in a polymer electrolyte membrane fuel cell (PEMFC) technology. The Ru_xW_ySe_z electrocatalyst was synthesised in an organic solvent for 3 h. The powder was characterised by transmission electron microscopy (TEM), and powder X‐ray diffraction (XRD). The electrocatalyst consisted of agglomerates of nanometric size (∼50–150 nm) particles. In the electrochemical studies, rotating disc electrode (RDE) and rotating ring‐disc electrode (RRDE) techniques were used to determine the oxygen reduction kinetics in 0.5 M H₂SO₄. The kinetic studies include the determination of Tafel slope (112 mV dec^–1), exchange current density at 25 °C (1.48 × 10^–4 mA cm^–2) and the apparent activation energy of the oxygen reaction (52.1 � 0.4 kJ mol^–1). Analysis of the data shows a multi‐electron charge transfer process to water formation, with 2% H₂O₂ production. A single PEMFC with the Ru_xW_ySe_z cathode catalysts generated a power density of 180 mW cm^–2. Performance achieved with a loading of 1.4 mg cm^–2 of a 40 wt% Ru_xW_ySe_z and 60 wt% carbon Vulcan (i.e. 0.56 mg cm^–2 of pure Ru_xW_ySe_z). Single PEMFC working was obtained with hydrogen and oxygen at 80 °C with 30 psi.     

Drawing and ultimate tenacity properties of polyamide 6/attapulgite composite fibers

The drawing and ultimate tenacity properties of the Polyamide 6 (PA6)/Attapulgite (ATP) composite fiber specimens prepared at varying modified ATP (mATP) contents and drawing condition were systematically investigated. As evidenced by Fourier transform infrared (FTIR) and morphological analysis, demarcated translucent resins were found firmly attached on the surfaces of ATP nanofibers. The specific surface areas of the mATP specimens reached a maximum value at 381 m²/g as the weight ratios of silane coupling agents to ATP nanofibers reached an optimum value at 1.0. The percentage crystallinity and melt shear viscosity values measured at varying shear rates of PA6_x(mATP)_y specimens increased consistently as their mATP contents increased. In contrast, melting temperatures of PA6_x(mATP)_y specimens reduced slightly as their mATP contents increased. At a fixed drawing temperature and rate, the achievable draw ratio (D_ra) values of PA6_x(mATP)_y as‐spun fiber specimens approach a maximum value, as their mATP contents are close to the 0.2 wt % optimum value. The maximum D_ra values obtained for PA6_99.8(mATP)_0.2 as‐spun fiber specimens reached another maximum, when their drawing temperatures and rates approached the optimum values at 120°C and 50 mm/min, respectively. At a fixed draw ratio, the tenacity values of PA6_x(mATP)_y drawn fiber specimens drawn at the optimum drawing temperature and rate reached a maximum value, as their mATP contents approached the 0.2 wt % optimum value. Possible reasons accounting for the interesting morphological, specific surface area, drawing, orientation, and ultimate tenacity properties found for the PA6_x(mATP)_y fiber specimens are proposed. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Direct electrochemical detection of pyruvic acid by cobalt oxyhydroxide modified indium tin oxide electrodes

An enzyme-free electrode was fabricated by anodic electrodeposition of cobalt oxyhydroxide film on an ITO electrode (CoO_x(OH)_y/ITO) for direct electrochemical detection of pyruvic acid (PA) in solution. Scanning electron microscopy (SEM) and atom force microscopy (AFM) were employed to characterize the morphology of CoO_x(OH)_y film. Cyclic voltammetry (CV) was used to investigate the electrochemical properties of PA on CoO_x(OH)_y/ITO in order to select the optimal potential for the chronoamperometric detection of PA. It was found that the CoO_x(OH)_y/ITO electrode served as an excellent PA sensor with a linear detection range of 1.00 μM to 1.91 mM, a detection limit of 0.55 μM, and a high sensitivity of 417.1 μA mM⁻¹ cm⁻². Moreover, the response time of CoO_x(OH)_y/ITO to PA is less than 10 s, which is the shortest for PA detection reported in literature using electrochemical method. These properties and the high stability of CoO_x(OH)_y/ITO made it a good candidate for developing electrochemical enzyme-free PA sensing device.     

Rheological,mechanical, optical,and transport properties of blown films of polyamide 6/residual monomer/montmorillonite nanocomposites

Exfoliated nanocomposites of polyamide 6 (PA6) with residual monomer and an organically treated montmorillonite (3 and 5 wt %) were produced by twin‐screw extrusion. The composites had their steady state, dynamic, and transient rheological properties measured by parallel‐plates rheometry; their exfoliation level was characterized by wide angle X‐rays diffraction (WAXD) and transmission electron microscopy (TEM). The characterization showed as follows: (i) the nanoclay's lamellas were well dispersed and distributed thru the PA6, (ii) the postpolymerization of the residual monomer produced more branched chains than linear ones in the pure PA6, (iii) the nanoclay's lamellas acted as entanglement points in the nanocomposites, and (iv) the molecular weight of the PA6 in the nanocomposites decreased. Blown films of the nanocomposites were produced by single screw extrusion; the die pressure during the film blowing of the nanocomposites strongly decreased. The tensile mechanical properties of the blown films were also measured. Along the machine direction (MD), the best mechanical properties were obtained with the 5 wt % nanocomposite, whereas along the transverse direction (TD), the 3 wt % nanocomposite had the best behavior. The glass transition temperature (T_g) of the blown films was measured by dynamic mechanical thermal analyses (DMTA). The 5 wt % nanocomposite had the highest T_g of all the films. The optical properties were measured by spectrophotometry; the nanoclay decreased the films' haze, but the level of transmittance was not affected. The water vapor and oxygen permeability rates of the nanocomposites films were found to be lower than in the pure PA6 blown film as a result of a tortuosity effect. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Realizing the invariant electrostrain response and low hysteresis via multicomponent coordination in Pb-based ceramics

High-performance piezoelectric materials are essential in many piezoelectric devices. However, the composition of piezoelectric materials usually has a great influence on their performance. In this work, xBi(Mg_1/2Ti_1/2)O₃–yPbZrO₃–zPbTiO₃ (xBMT–yPZ–zPT; 0.2 ≤ x ≤ 0.4, 0.25 ≤ y ≤ 0.4, and 0.35 ≤ z ≤ 0.4) ternary ceramics with different compositions were synthesized and it was found that the strain response was not sensitive to the composition. The crystal structure, strain response, ferroelectric properties, and temperature stability of xBMT–yPZ–zPT ceramics were investigated in detail. X-ray diffraction patterns show that all the as-prepared xBMT–yPZ–zPT ceramics with x = 0.2, 0.3, 0.4, and 0.5 possess a perovskite structure. Under an external electric field of 6 kV mm⁻¹, the strain values of xBMT–yPZ–zPT ternary ceramics with x = 0.2, 0.3, 0.4, and 0.5 were 0.30%, 0.31%, 0.30%, and 0.27%, respectively. In addition, the strain hysteresis of these ternary ceramics is also almost the same and low. These merits make xBMT–yPZ–zPT piezoelectric ceramics have broad application prospects in the field of commercial actuators.     

Structural characterization of hydrophilic polymer blends/montmorillonite clay nanocomposites

The nanocomposite films comprising polymer blends of poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), poly(ethylene oxide) (PEO), and poly(ethylene glycol) (PEG) with montmorillonite (MMT) clay as nanofiller were prepared by aqueous solution casting method. The X‐ray diffraction studies of the PVA–x wt % MMT, (PVA–PVP)–x wt % MMT, (PVA–PEO)–x wt % MMT and (PVA–PEG)–x wt % MMT nanocomposites containing MMT concentrations x = 1, 2, 3, 5 and 10 wt % of the polymer weight were carried out in the angular range (2θ) of 3.8–30°. The values of MMT basal spacing d₀₀₁, expansion of clay gallery width W_cg, d‐spacing of polymer spherulite, crystallite size L and diffraction peak intensity I were determined for these nanocomposites. The values of structural parameters reveal that the linear chain PEO and PEG in the PVA blend based nanocomposites promote the amount of MMT intercalated structures, and these structures are found relatively higher for the (PVA–PEO)–x wt % MMT nanocomposites. It is observed that the presence of bulky ester‐side group in PVP backbone restricts its intercalation, whereas the adsorption behavior of PVP on the MMT nanosheets mainly results the MMT exfoliated structures in the (PVA–PVP)–x wt % MMT nanocomposites. The crystallinities of the PEO and PEG were found low due to their blending with PVA, which further decreased anomalously with the increase of MMT concentration in the nanocomposites. The decrease of polymer crystalline phase of these materials confirmed their suitability in preparation of novel solid polymer nanocomposite electrolytes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40617.     

Laser ablation of Ga-Sb-Te thin films monitored with quadrupole ion trap time-of-flight mass spectrometry

Laser ablation of Ga-Sb-Te chalcogenide thin films prepared by radiofrequency magnetron co-sputtering was monitored with quadrupole ion trap time-of-flight mass spectrometry (QIT-TOF-MS). The mass spectra of 11 thin films of various compositions (Ga: 0–53.1, Sb: 0–52.0, and Te: 0–100.0 at. %) were recorded. Several series of unary (Ga_x, Sb_y, and Te_z) binary (Ga_xSb_y, Ga_xTe_z, and Sb_yTe_z), and ternary Ga_xSb_yTe_z clusters were identified in both positive and negative ion modes. Stoichiometry of observed clusters was determined. Up to 18 binary clusters (positively and negatively charged) were detected for thin film with low Sb content of 6.5 at. %. The highest number (4) of ternary clusters was observed for thin film with high Te content of 66.7 at. %. The number of generated clusters and their peaks intensity varied according to the chemical composition of thin films. Altogether, 41 clusters were detected. The laser ablation monitoring shows laser-induced fragmentation of thin film structure. The relation of clusters stoichiometries to the chemical composition of thin films is discussed. The fragmentation can be diminished by covering a surface of thin films with paraffin's, glycerol, or trehalose sugar thin layers. The stoichiometry of generated clusters shows partial structural characterization of thin films.     

Mechanical properties of films of poly(vinyl alcohol) derived from vinyl trifluoroacetate

In order to study the influence of the stereoreguralities of polymer chains on the mechanical properties of films of poly(vinyl alcohol) (PVA)_(VTFA) derived from vinyl trifluoroacetate, the strength of the film was measured. In the case of undrawn PVA_(VTFA) films, Young's modulus and strength at break were the smallest at the annealing temperature of about 100°C. It is considered to be due to the melt of small microcrystals and the increase in mobility of chains in amorphous parts. Young's moduli of undrawn PVA_(VTFA) films were in the range of 1.50–3.75 GPs and the values were higher than that (0.17–0.36 GPa) of undrawn film of commercial PVA with the low concentration of syndiotacticity and the high concentration of head-to-head bounds. In the case of drawn, annealed PVA_(VTFA) films, the maximum Young's modulus was about 20 GPa.     

Characterization and Properties of Reactive Poly(lactic acid)/Polyamide 610 Biomass Blends

A low molecular weight bisphenol‐A type epoxy resin was used as a reactive compatibilizer for poly(lactic acid) (PLA)/polyamide 610 (PA 610) biomass blends. To the best of our knowledge, this blend is the first biomass PA 610 blend in the literature. The epoxy functional groups could react with the terminal groups of both PLA and PA 610. An ester–amide interchange reaction led to a polyester–polyamide copolymer formation, and improved the compatibility of PLA and PA 610. The blends with epoxy resin showed an enhancement in the phase dispersion and interfacial adhesion compared with the blend without epoxy resin. The differential scanning calorimetry (DSC) analysis showed that the crystallization peak temperatures decreased with increasing epoxy content. The melting temperature of PA 610 decreased with the addition of PLA, but remained unchanged with increased compatibilizer dosages. The dynamic mechanical analysis (DMA) showed that the glass transition temperature (T_g) of the blend, with the addition of 0.5 phr epoxy resin, slightly increased compared with that of neat PLA. However, the T_g of the blends remained unchanged with increasing epoxy resin content, and the higher content of epoxy resin in the blends resulted in improved mechanical properties and higher melt viscosity. The unnotched impact test showed that PA 610 could toughen PLA with the addition of epoxy resin. Moreover, the no‐break unnotched impact behavior was observed with the medium content of the compatibilizer, improving the notch sensitivity of PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2563–2571, 2013     

Miscibility and phase structure of binary blends of poly(L‐lactide) and poly(vinyl alcohol)

Blend films of poly(L ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA) were obtained by evaporation of hexafluoroisopropanol solutions of both components. The component interaction, crystallization behavior, and miscibility of these blends were studied by solid‐state NMR and other conventional methods, such as Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WAXD). The existence of two series of isolated and constant glass‐transition temperatures (T_g's) independent of the blend composition indicates that PLLA and PVA are immiscible in the amorphous region. However, the DSC data still demonstrates that some degree of compatibility related to blend composition exists in both PLLA/atactic‐PVA (a‐PVA) and PLLA/syndiotactic‐PVA (s‐PVA) blend systems. Furthermore, the formation of interpolymer hydrogen bonding in the amorphous region, which is regarded as the driving force leading to some degree of component compatibility in these immiscible systems, is confirmed by FTIR and further analyzed by ¹³C solid‐state NMR analyses, especially for the blends with low PLLA contents. Although the crystallization kinetics of one component (especially PVA) were affected by another component, WAXD measurement shows that these blends still possess two isolated crystalline PLLA and PVA phases other than the so‐called cocrystalline phase. ¹³C solid‐state NMR analysis excludes the interpolymer hydrogen bonding in the crystalline region. The mechanical properties (tensile strength and elongation at break) of blend films are consistent with the immiscible but somewhat compatible nature of these blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 762–772, 2001     

Ultradrawing and ultimate tensile properties of ultrahigh molecular weight polyethylene composite fibers filled with functionalized nanoalumina fillers

Ultradrawing and ultimate tensile properties of ultrahigh molecular weight polyethylene (UHMWPE) composite fibers were successfully improved by the addition of nanoalumina (NAL), acid treated nanoalumina (ATNAL), and/or functionalized nanoalumina (FNAL). As evidenced by FTIR and TEM analyses, maleic anhydride grafted polyethylene (PE_g‐MAH) molecules were successfully grafted onto ATNAL fillers. The specific surface areas of FNAL fillers reached a maximal value at 516 m²/g, as they were modified using an optimal weight ratio of PE_g‐MAH to ATNAL at 8. Achievable draw ratio (D_ra) values of UHMWPE/NAL (F₁₀₀A_y), UHMWPE/ATNAL (F₁₀₀A_x%‐8‐y) and/or UHMWPE/FNAL (F₁₀₀A_x%‐8FPE^z_y) as‐prepared fibers approached a maximal value as NAL, ATNAL, and/or FNAL contents reached an optimal value at 0.1, 0.1, and 0.075 phr, respectively. The maximal D_ra values of F₁₀₀A_x%‐8FPE^z_0.075 as‐prepared fiber specimens were significantly higher than those of F₁₀₀A_0.1 and F₁₀₀A_x%‐8‐0.1 as‐prepared fiber specimens. In which, the maximal D_ra values obtained for F₁₀₀A_x%‐8FPE^z_0.075 as‐prepared fibers reached another maximal value as FNAL fillers were modified using an optimal weight ratio of PE_g‐MAH to ATNAL at 8. The ultimate tensile strength value of F₁₀₀A_2%‐8FPE⁸_0.075 drawn fiber reached 6.4 GPa, which was about 2.4 times of that of the UHMWPE drawn fibers prepared at the same optimal UHMWPE concentration and drawing condition. POLYM. ENG. SCI., 55:2205–2214, 2015. © 2015 Society of Plastics Engineers     

Effects of Plasticizing on Mechanical and Viscous Characteristics of Poly(vinyl alcohol): A Comparative Study between Glycerol and Diethanolamine

Although plasticizing materials by modification with small-molecular chemicals has been extensively utilized in the industrial community, processing poly(vinyl alcohol) (PVA) at high concentrations (C_PVA) or with a high degree of polymerization (DP) remains challenging. Optimization the plasticizing conditions is one means of addressing this issue. In this study, two types of frequently used plasticizers, glycerol (GLY) and diethanolamine (DEA), are chosen to plasticize PVA resin with a DP of 2400. Both PVA/plasticizer films possess excellent optical transmittance and mechanical ductility, whereas the films blended with DEA exhibit higher strength than the PVA/GLY films. The viscosity variation in the temperature (T_op)–C_PVA space is monitored by real-time viscous flow testing, demonstrating that DEA is more effective for reducing the viscosity of PVA, which should improve the processability, facilitating film-forming from concentrated solutions. Furthermore, density functional theory calculations and molecular dynamics simulations illustrate that the PVA/DEA system has a lower binding energy, longer hydrogen bond length, and higher isotropic diffusion coefficient, indicating a stable hydrogen bond network and homogenous dispersion of the plasticizer, leading to good solution fluidity and mechanical performance. This study is significant for guiding the design and manufacture of optically transparent, high-performance PVA films as polarizer precursor.     

Tunable color emission in LaScO3:Bi3+,Tb3+,Eu3+ phosphor

LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ (x = 0 − 0.04, y = 0 − 0.05, z = 0 − 0.05) phosphors were prepared via high-temperature solid-state reaction. Phase identification and crystal structures of the LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ phosphors were investigated by X-ray diffraction (XRD). Crystal structure of phosphors was analyzed by Rietveld refinement and transmission electron microscopy (TEM). The luminescent performance of these trichromatic phosphors is investigated by diffuse reflection spectra and photoluminescence. The phenomenon of energy transfer from Bi³⁺ and Tb³⁺ to Eu³⁺ in LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ phosphors was investigated. By changing the ratio of x, y, and z, trichromatic can be obtained in the LaScO₃ host, including red, green, and blue emission with peak centered at 613, 544, and 428 nm, respectively. Therefore, two kinds of white light-emitting phosphors were obtained, LaScO₃:0.02Bi³⁺,0.05Tb³⁺,zEu³⁺ and LaScO₃:0.02Bi³⁺,0.03Eu³⁺,yTb³⁺. The energy transfer was characterized by decay times of the LaScO₃:xBi³⁺, yTb³⁺, zEu³⁺ phosphors. Moreover absolute internal QY and CIE chromatic coordinates are shown. The potential optical thermometry application of LaScO₃:Bi³⁺,Eu³⁺ was based on the temperature sensitivity of the fluorescence intensity ratio (FIR). The maximum S_a and S_r are 0.118 K⁻¹ (at 473.15 K) and 0.795% K⁻¹ (at 448.15 K), respectively. Hence, the LaScO₃:Bi³⁺,Eu³⁺ phosphor is a good material for optical temperature sensing.     

Hydrophobic surface properties of fluoropolyetherimide blends for pervaporation membranes

The well‐known polyetherimide (ULTEM 1000) is obtained by step‐reaction of bisphenol. A diphthalic anhydride (BAPA) with m‐phenylene diamine and newly related fluorinated poly etherimides synthesized from BAPA and 2,3‐bis(2,2,3,3,4,4,5,5,5‐nonafluoropentyl)butan‐1,4 diamine (NFD) led to compatible blends over the entire range of composition. Miscible one‐phase blends have been suggested by a good correlation of T_g versus NFD monomer unit weight fraction (w) (Fox and Couchman equations) and a regular morphology by scanning electron microscopy. Surface energy of blend films fell from 45.3 to 27.4 mJ m^?2 for w ≥ 0.1 corresponding to a NFD molar fraction y ≥ 0.06. Cast‐evaporated films from fluorinated copolyetherimides and blends with y < 0.15 were ductile and gave conveniently hydrophobic non‐porous membranes that withstood the experimental conditions of pervaporation tests. Copyright © 2003 Society of Chemical Industry     

Interfacial slip‐stick transition induced by reactive compatibilization in ethylene‐co‐butyl acrylate elastomer dispersed polyamide 6 blend subjected to high shear flow and extensional flow

The effect of phase interaction induced by reactive compatibilization during high shear and extensional flow in polyamide (PA6) and ethylene‐co‐butyl acrylate (EBA) blends was studied using advanced dual bore capillary rheometer. The viscosity‐composition behavior of the uncompatibilized PA6/EBA blends exhibited negative deviation behavior from log‐additivity rule. The interfacial slip mechanism, operative between the matrix PA6 and dispersed EBA during shear flow was studied by the use of Lin's and Bousmina‐Palierne‐Utracki (BPU) model for viscosity for the blends under the processing conditions. On the other hand, the compatibilized PA6/EBA‐g‐MAH^0.49/EBA blends with varying dispersed phase volume fraction show positive deviation behavior. The reactive compatibilizers EBA‐g‐MAH^0.49 and EBA‐g‐MAH^0.96 increased the phase interaction with adequate reduction in the dynamic interfacial tension, which favored the particle break‐up and stabilized the morphology in the compatibilized blends. The extensional viscosity of the blends has enhanced because of the inclusion of EBA in all the uncompatibilized and compatibilized blends. The melt elasticity and elasticity function were systematically studied from first normal stress coefficient functions (ψ₁). The variation in the recoverable shear strain (γ_R), shear rate dependent relaxation time (λ) and shear compliance (J_c) under various shear rates were thoroughly analyzed for all the blend compositions. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Free‐volume hole properties of two kinds thermoplastic nanocomposites based on polymer blends probed by positron annihilation lifetime spectroscopy

Two type of nanocomposites—an immiscible blend, high density polyethylene/polyamide 6 (HDPE/PA‐6) with organomodified clay, and a compatibilized blend, high density polyethylene grafted with acrylic acid/PA‐6 (PEAA/PA‐6) with organomodified clay—were prepared via melt compounding. X‐ray diffraction and transmission electron microscopy results revealed that the clay was intercalated and partially exfoliated. Positron annihilation lifetime spectroscopy has been utilized to investigate the free‐volume hole properties of two type of nanocomposites. The results show a negative deviation of free‐volume size in PEAA/PA‐6 blend, and a positive deviation in HDPE/PA‐6 blend, and I₃ has a greater negative deviation in compatibilized blend than in immiscible blend due to interaction between dissimilar chains. For nanocomposites based on polymer blends, in immiscible HDPE/PA‐6/organomodified clay system, the variation of free‐volume size with clay content is not obvious and the free‐volume concentration and fraction decreased. While in the case of compatibilized PEAA/PA‐6/organomodified clay nanocomposites, complicated variation of free‐volume properties due to interactions between two phases and organomodified clay was observed. And the interaction parameter β shows the interactions between polymers and organomodified clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2463–2469, 2006     

A transdermal diltiazem hydrochloride delivery device using multi-walled carbon nanotube/poly(vinyl alcohol) composites

Membranes with high strength and elasticity are of great demand in patch therapy. Similar membranes have been developed by combining carboxy-functionalized multiwalled carbon nanotube (c-MWCNT) with different poly(vinyl alcohol) (PVA) as potential diltiazem delivery device through aqueous mixing. High molecular weight PVA (PVA_H) produced stronger interaction with c-MWCNT than low molecular weight PVA (PVA_L) preferably at low concentration. Positive changes in favor of PVA_H in infrared and solid state ¹³C nuclear magnetic resonance spectroscopy, wide angle X-ray scattering, thermal stability, morphology and dry and wet mechanical properties clearly demonstrate that. Fibrillar c-MWCNT array at 1 wt.% in PVA_H (PVA_H/1) has drastically improved PVA crystalline cell dimension, tensile strength (201%) and elongation (196%) than neat PVA_H whereas the similar improvement is much less (100% and 185%) in PVA_L (PVA_L/1) due to globular morphology. Instead, c-MWCNT performed better at 0.5 wt.% in PVA_L (PVA_L/0.5). The kinetic data reflects better encapsulation and slower release by PVA_H (5.87%) than PVA_L (10.17%) due to greater interfacial interaction.