Micromechanical modeling of compressive behavior in freeze-casted ceramic

In this study, a novel computational micromechanical framework is proposed to predict the effective mechanical properties of the ice-templated ceramics under off-axis compressive loading. The mechanical behavior is simulated by a computational micromechanical model and validated against experimental results. Smeared cracking approach was used to describe failure in ice-templated alumina. The representative volume element (RVE) was developed based on the honeycomb analogy of lamellar walls considering the morphology of the material. The periodic boundary conditions were applied in RVE to simulate bulk behavior of the material. The compression testing was conducted on the ice-templated alumina samples to obtain the effective compressive moduli and strength with different loading angles. Digital image correlation method was used to measure strain field during the experiment and quantify the effective misalignment angle corresponding to porous material. The effective stiffness and strength obtained from RVE analysis compared well with experimental results. The proposed micro-mechanical RVE model allows for determining the properties of the ice-templated porous ceramic for various off-axis angles.     

Hierarchical Structure of Porous Silicon Nitride Ceramics with Aligned Pore Channels Prepared by Ice‐Templating and Nitridation of Silicon Powder

A unique hierarchical porous structure of silicon nitride ceramic with 76.5% porosity is fabricated by combining an ice‐templating method and nitridation for a silicon powder. The porous silicon nitride ceramics were composed of a lamellar structure with aligned pore channels and ceramic walls filled with fibrous whiskers. This study is focused on the influences of freezing rate on the microstructures and properties of the silicon nitride ceramics. The properties were characterized by compressive strength and gas permeability, which were shown to vary with controlled microstructure. The compressive strength and the permeability reached up to 32.2 MPa and 0.035^?12 m², respectively.     

Fabrication of high strength and thermal insulation porous ceramics via adjusting the fiberglass contents

Fiberglass porous ceramics were successfully prepared via a foam-gelcasting process with fiberglass and glass particles. The effects of fiber content on the rheology of foaming slurries and the structure and mechanical properties of as-prepared porous ceramics were investigated. The results showed that as the ratio of fiberglass to glass particles increased, the thixotropy of slurries decreased, which affected the foamability of slurries. When the ratio of fiberglass to particle was 75:25, the slurries exhibited excellent flowability and outstanding foamability, which was beneficial to optimize the structure of pores and improve the properties of the porous ceramics. The porosity, compressive strength, and thermal conductivity of porous ceramics with a content of 75 wt.% fiberglass treated at 750°C were 78.3%, 2.15 MPa, and .11 W/(m·K) (room temperature), respectively. Therefore, the prepared porous ceramics with a ratio of fiberglass to particle 75:25 were regarded as an ideal candidate for thermal insulation materials.     

Effects of fiber aspect ratio and fabrication temperature on the microstructure and mechanical properties of elastic fibrous porous ceramics by press-filtration method

The inherent brittleness of fibrous porous ceramics (FPCs) results in their fragility, limiting their application in thermal protection. In this paper, a novel elastic fibrous porous ceramic (EFPCs) with quasi-layered structure were successfully prepared by facile press-filtration method. To further investigate the characteristics of EFPCs, the effect of fiber aspect ratio and fabrication temperature on the microstructures and properties were studied. Results demonstrated that both fiber aspect ratio and fabrication temperature had influence on the microstructure and mechanical properties on EFPCs. The prepared EFPCs exhibited low density (0.124–0.181 g cm^?3), relatively high compressive stress (0.096–0.377 MPa) compared to flexible fibrous ceramics, high porosity (91.73%–94.86%) and low thermal conductivity (～0.03 W m^?1 k^?1). According to these excellent properties, the EFPCs may have potential use in thermal insulation fields.     

Porous YSZ Ceramics Reinforced by Different Kinds of Fibers

Porous YSZ ceramics reinforced by different fibers were prepared by gel‐casting with 15% solid content and pressureless sintering. The four kinds of fibers (mullite, aluminosilicate, Al₂O₃, and YSZ fibers) were added into the YSZ ceramics with the same 10% vol content. After sintered at 1500°C for 2 h, aluminosilicate and mullite fibers could not be found in the samples of porous YSZ ceramics, which showed they reacted with YSZ ceramics at high temperature, while YSZ and Al₂O₃ fibers still kept perfect after sintering. Furthermore, the influences of fiber content, sintering temperature, porosity of matrix materials on compressive strength and porosity of the porous YSZ ceramics were studied. The results showed that Al₂O₃ fiber showed more obvious reinforcing effect than YSZ fiber on porous YSZ ceramics. The fiber‐reinforcing effects depend on fiber content, sintering temperature, and porosity of matrix materials. The fiber addition can improve the shrinkage behavior of porous ceramics during sintering and strengthen the skeleton of porous ceramics.     

Y_2O_3添加剂对SiC复相多孔陶瓷烧结性能和力学性能的影响

利用添加造孔剂法制备SiC复相多孔陶瓷。研究了Y2O3添加剂对SiC复相多孔陶瓷的烧结温度及烧结体力学性能的影响机理。结果表明:Y2O3的加入大大降低了SiC复相多孔陶瓷烧结温度,样品的力学性能有所提高,抗弯强度提高18.46%,稀土氧化物占总质量3%时能提高SiC复相多孔陶瓷的抗氧化性,氧化速率降低了66.7%。YAG相在SiC晶界均匀分布,细晶,裂纹偏转及晶界桥联是SiC复相多孔陶瓷的增韧的机理。     

Effect of organic fibers addition on digital light processing for Al2O3 porous ceramics

Porous ceramics based on additive manufacturing have great application potential in many industries, including filtration, catalysis, and heat insulation. In this research, we propose a method for manufacturing porous ceramics with connected channels structure through ceramic digital light processing (DLP) and organic fiber decomposition. The crossed fibers in the green body, working as a pore-forming agent, were decomposed and removed to form connected channels in ceramic. It was confirmed that ball milling changed the fiber morphology during slurry preparation, which was beneficial to promote fibers crossing. Besides, we focused on the influence of the “Sponge Compression effect” during the DLP process, which affected the fibers distribution. The existence of fibers in the green body resulted in uneven pressure distribution during the debinding process, providing a potential source of cracks. Results show that this method can produce channels with a diameter of 100 μm and high connectivity, providing great potential in fabricating high connectivity porous ceramics with complex shapes and structures.     

Synthesis and characterization of mullite-ZrO2 porous fibrous ceramic for highly efficient oil-water separation

This work aimed to proposing a new strategy for preparing the mullite-ZrO₂ porous fibrous ceramic used as alternative matrix material for oil-water separation by the aqueous gel-casting method. The properties of the fabricated porous fibrous ceramics in terms of microstructure, phase composition, apparent porosity, bulk density and compressive strength were investigated and the separation behavior was predicted by analyzing the structural changes. It is demonstrated that the phase composition of green bodies consisted of bayerite, boehmite, ZrSiO₄ and YSZ, and the sintered sample contained mullite, ZrO₂ and YSZ. As the YSZ fibers increased, the porosity of the fabricated porous ceramic increased with the maximum value of 70.65% due to the formation of more pores caused by YSZ fibers. Moreover, a significant increase in compressive strength (up to 9.52–21.86 MPa) was observed with the increase of YSZ fibers. Therefore, the fabricated porous ceramics could be appropriative for advanced applications of separation membranes for oil-water separation.     

Enhancing thermal insulation and mechanical strength of porous ceramic through size-graded MA Hollow Spheres

In this study, a series of porous ceramics were prepared using different ratios of small and large size MA hollow ceramic spheres as pore-forming agents, and their thermal insulation properties were investigated. The results showed that increasing the proportion of small size hollow ceramic spheres could effectively decrease the thermal conductivity and improve the compressive strength of the porous ceramics. The optimal porous ceramic was prepared with a ratio of 10∼50 of small and large size hollow ceramic spheres, which had a thermal conductivity of 0.368 W/(m·K) at 800 °C and a compressive strength of 22.43 MPa. Microscopic analysis indicated that the enhanced thermal insulation and mechanical properties were due to the improved pore structure and the enhanced bonding strength between the ceramic spheres and the matrix. The findings provide valuable insights for the development of high-performance thermal insulation materials.     

A facile approach for preparing Al2O3 reticulated porous ceramics with optimized closed-cell struts and excellent mechanical properties

Reticulated porous ceramics (RPCs) are of great value in applications such as non-ferrous alloys and flue gas filtration. For the purpose of further enhancing the mechanical properties of RPCs without drastically reducing their apparent porosity, a new route to improve the mechanical properties of the strut by constructing a closed-cell structure was proposed to fabricate Al₂O₃ reticulated porous ceramics (ARPCs). The effects of cryolite on the generation of closed pores, the microstructure, and the mechanical performance of struts were investigated. It was found that the addition of cryolite promoted the densification of the pore walls within the struts during sintering. Furthermore, ARPCs added with 10 wt% cryolite achieved an apparent porosity of nearly 80%, while exhibiting excellent mechanical strength and thermal-shock resistance, with compressive strength and residual strength ratio significantly increased by 56% and 11%, respectively, compared to the samples without cryolite addition.     

Microstructure,mechanical behavior and oxidation resistance of disorderly assembled ZrB2-based short fibrous monolithic ceramics

Axially aligned fibrous monolithic ceramics present non-catastrophic fracture behavior via crack deflection and delamination along cell boundaries. However, severe in-plane anisotropy and time-consuming preparation procedures prevent their extensive promotion. The introduction of high content of weak phase components with poor oxidation resistance in weak interface destroys the excellent oxidation resistance of ceramic matrix. In this work, ZrB₂-based short fibrous monolithic (SFM) ceramics with in-plane isotropic mechanical properties and excellent oxidation resistance were easily prepared by hot pressing randomly assembled short ceramic fibers. The microstructure and mechanical behavior of ZrB₂-based SFM ceramics densified at various temperatures were systematically investigated. The mechanical properties of ZrB₂-based SFM ceramics slightly improved with the increase of sintering temperature. ZrB₂-based SFM ceramics exhibited excellent oxidation resistance and remained intact without macroscopic cracks after ablation for 615 s in oxyacetylene flame with maximum temperatures exceeding 2150 °C. The oxidation behavior was analyzed in detail.     

Lamellar BaTiO3 and its composites fabricated by the freeze casting technique

In this investigation, the freeze casting technique was employed to fabricate ceramic–epoxy composites. Porous BaTiO₃ ceramics exhibited lamellae architectures with strong anisotropy but with poor mechanical property. BaTiO₃–epoxy composites in longitudinal direction showed high dielectric constants which were 1 order of magnitude higher than those of conventional composites with randomly distributed ceramic particles. With the addition of alumina, the compressive strength of porous BaTiO₃ ceramics could be enhanced and the dielectric constants of ceramic–epoxy composites were lowered, but they were still much higher than those of the traditional composites. In a word, the properties of the composites could be optimized by adding proper amount of alumina.     

用冰模板法制备定向结构氧化锆多孔陶瓷

以冰为造孔模板制备氧化锆多孔陶瓷。采用扫描电镜观察微观结构,并测量其气孔率和体积密度。结果表明:经过冷冻干燥工艺及高温烧结后,获得了定向排列的多孔结构。多孔陶瓷的气孔率为29.09%,体积密度为1.37g/cm3。     

Performance study of foam ceramics prepared by direct foaming method using red mud and K-feldspar washed waste

In this study, foam ceramics were prepared via a direct foaming method at high temperatures (1080–1120 °C), using red mud (RM) and K-feldspar washed waste (KFW) as the raw materials and SiC as the foaming agent, respectively. The chemical compositions and crystalline phases of the raw materials as well as the structural and mechanical properties of the foam ceramics were investigated. By adjusting the formulation and sintering process parameters, the porous structure of the foam ceramics could be effectively modulated. In addition to some residual crystalline phases in the raw materials, new phases, including rutile (TiO₂) and anorthite (CaAl₂Si₂O₈), were generated in foam ceramics. The compressive strength of the foam ceramics decreased with an increase in the KFW/RM ratio and sintering temperature, which was mainly related to the low density of the foam ceramics and the poor support of the pore walls to the structure. Among all the foam ceramics investigated, the foam ceramic with the KFW/RM ratio of 1:1, SiC content of 1 wt%, sintering temperature of 1100 °C and sintering time of 60 min showed the best overall performance with a bulk density, an apparent porosity, an average pore size and a compressive strength of 0.77 g/cm³, 61.89%, 0.52 mm, and 3.64 MPa, respectively. Its excellent porous structure and mechanical properties rendered it suitable for application as insulation materials or decorative materials for building partition walls.     

A review of the research progress on the interface between oxide fiber and oxide ceramic matrix

Oxide ceramics have excellent high temperature performance, superior thermal and chemical stability, which can be used in high temperature oxidizing environments, while oxide ceramics generally have low toughness and are prone to catastrophic damage... Oxide ceramics can be reinforced by high performance ceramic fibers to improve the fracture strength and fracture toughness, thus expanding its application in high-temperature components such as aero-engine combustion chambers and tail nozzles. The interface between fiber and matrix is an important factor that determines the performance of the composites. By tailoring the interface, the energy dissipation mechanisms such as fiber debonding and fiber pull-out can be brought into play to avoid the catastrophic damage of the composites. This review paper summarizes the recent research progress of the oxide fiber/oxide ceramic matrix composites interface. The mechanical properties of the interface and the design principles of the interface engineering are discussed, and types of interfaces and coating preparation methods are reviewed.     

Effect of alumina fiber content on pore structure and properties of porous ceramics

Porous Al₂O₃ ceramics with different contents of alumina fibers were prepared by gel-casting process. The effects of Al₂O₃ fiber content on pore size distribution, porosity, compressive strength, and load-displacement behavior of the ceramic materials were investigated. Initial results showed that with the increase of Al₂O₃ fiber content, the pore size and porosity of the material is increased, and the compressive strength is decreased. However, upon increasing the fiber content from 50 wt% to 67 wt%, the performance of the samples changed greatly. The compressive strength of the material increased, while the porosity remained unchanged, the pore size increased greatly, and the shape of the load displacement curve changed. It showed that when the fiber content increased from 50 wt% to 67 wt%, the loading body in the fiber-reinforced porous ceramics changed from particles to fibers.     

First printing of continuous fibers into ceramics

This article reports a novel method for three-dimensional (3D) printing of continuous fibers into ceramics to improve the mechanical properties of printed ceramics, which is difficult in other 3D printing technologies. The ceramics were derived by pyrolysis of thermoplastic ceramic precursor feedstocks, which were prepared by two methods. One is homogeneously mixing thermoplastic resins and ceramic precursors. The feedstocks prepared by this method exhibit good thermoplastic properties and can be extruded into filaments. Ceramics were obtained by heating the feedstocks to 1100°C in argon atmosphere. The ceramics were amorphous and remained stable during 1100-1300°C; at 1400°C they decomposed into β–SiC with simultaneous volatile gas generation. Above 1400°C, their quality decreased significantly due to cracking of ceramic skeletons. The other method is directly heating, extruding and printing the ceramic precursor. The precursors showed good printability and complex ceramic structures were printed with continuous carbon fibers inside. The continuous carbon fibers improved the flexural strength of pyrolytic ceramics, which is about 7.6 times better than that of the ceramics without fibers. The novel method unravels the potential of 3D printing of continuous fibers into ceramics with complex lightweight structures to improve the strength.     

Structure and properties of Al2O3-bonded porous fibrous YSZ ceramics fabricated by aqueous gel-casting

To meet requirements for high porosity and high strength, novel aqueous gel-casting process has been successfully developed to fabricate Al₂O₃-bonded porous fibrous YSZ ceramics with ρ-Al₂O₃ and YSZ fibers as raw materials. Microstructure, phase composition, apparent porosity, bulk density, thermal conductivity, and compressive strength of fabricated porous ceramics were investigated, and effects of fiber content on properties were discussed. According to results, bird nest 3D mesh with interlaced YSZ fibers and Al₂O₃ binder was formed, ensuring the ability to obtain high performance, lightweight ceramics. An increase in the number of YSZ fibers led to more complex interlaced arrangement of fibers and denser network structure of porous ceramics at retaining their stability. Furthermore, their apparent porosity and bulk density increased, whereas thermal conductivity and compressive strength decreased with increasing the fiber content. In particular, comparatively high porosity (71.1–72.7%), low thermal conductivity (0.209–0.503 W/mK), and relatively high compressive strength (3.45–4.24 MPa) were obtained for as-prepared porous ceramics, making them promising for applications in filters, thermal insulation materials, and separation membranes.     

Preparation of porous SiC ceramics skeleton with low-cost and controllable gradient based on liquid crystal display 3D printing

In recent years, the demand for gradient porous ceramics is increasing in engineering field. By traditional process, the disadvantage of prepared gradient porous ceramics is its low porosity and uncontrollable pore gradient, which limits the wide application of gradient porous ceramics. In this study, the gradient porous ceramic skeleton (GPCS) was prepared by combining liquid crystal display (LCD) 3D printer with liquid silicon infiltration (LSI). Experimental results showed that the mass of ceramic powder in the ceramic slurry with optimal printing performance accounts for 45% of the mass of photosensitive resin, and the thermal decomposition rate of photosensitive resin is faster in the range of 300–450 °C. Furthermore, the effect of LSI temperature on the composition, microstructure and mechanical properties of GPCS was investigated. The GPCS is expected to be applied in the fields of energy storage, heat transfer and biofouling, among others.     

Fabrication and properties of C/SiC porous ceramics by grinding-mould pressing-sintering process

High temperature resistant porous ceramics are considered to be prime candidates for applications in the transpiration cooling system of a hypersonic vehicle. This paper describes a new preparation process including grinding-mould pressing-sintering process, which is successfully used to fabricate C/SiC porous ceramics with high compressive strength and excellent permeability. The effects of carbon fiber content on the microstructure, mechanical property, pore size distribution and permeability of this porous ceramic are investigated in detail. The results indicate that this porous ceramic prepared in this study exhibits high compressive strength (～270.82 MPa) and excellent permeability (～3.937 × 10^?8 mm²). The C/SiC porous ceramics fabricated in this study will have potential application in active thermal protection systems.