In situ preparation of SiC/Si3N4-NW composite powders by combustion synthesis

Large-scale composite powders containing silicon carbide (SiC) particles and silicon nitride nanowires (Si₃N₄-NWs) were synthesized in situ by combustion synthesis (CS). In this process, a mixture of silicon, carbon black, polytetrafluoroethylene (PTFE) and a small amount of iron powders was used as the precursor. The products were characterized by XRD, SEM, EDS and TEM. The particles are equiaxed with diameters in the micron range, and the in situ formed nanowires are straight with uniform diameters of 20-350 nm and lengths of tens of microns. The Si₃N₄-NWs are characterized to be α-phase single crystals grown along the [1 0 1] or [1 0 0] direction. VLS and SLGS processes are proposed as the growth mechanisms of the nanowires. The as-synthesized powders have great potential for use in the preparation of high-performance SiC/Si₃N₄-NW composites.     

Influence of H2/NH3 mixtures on the composition of SiCNYO and SiCNAl(O) nanopowders

We performed pyrolysis of SiCNAlH and SiCNYOH nanopowder precursors under a reactive atmosphere (Ar/NH₃/H₂) with various compositions of ammonia (NH₃) and dihydrogen (H₂) to diminish C content, which is deleterious for thermal stability and sintering of the powders. This paper continues a previous work on the fabrication of an Si₃N₄/SiC composite without free C by studying the effect of H₂ on the C/N atomic ratio of the powder. We studied the influence of the nature of the gaseous mixture (Ar/NH₃/H₂) on the powder composition. Elemental analysis showed that the introduction of H₂ in the pyrolysis atmosphere limited the decomposition of NH₃ and allowed for control of the C/N ratio. This behaviour can be explained by the structural evolution observed by ²⁹Si NMR spectrometry but also by Fourier transform infrared and Raman spectroscopy. An Si₃N₄/SiC composite, with traces of free C, was obtained after post-pyrolysis heat treatment of the powders synthesized with 10 wt.% of H₂ and 25 wt.% NH₃.     

Thermal shock resistance of in situ formed Si2N2O–Si3N4 composites by gelcasting

Thermal shock resistance of Si₂N₂O–Si₃N₄ composites was evaluated by water quenching and subsequent three-point bending tests of strength diminution. Si₂N₂O–Si₃N₄ composites which was prepared with in situ liquid pressureless sintering process using Yb₂O₃ and Al₂O₃ powders as sintering additives by gelcasting showed no macroscopic cracks and the critical temperature difference (ΔT_c) could be up to 1400 °C. A mass of pores existed in the sintered body and the irregular shaped fibers extended from the pores increased the thermal shock property.     

The influence of mechanochemical activation on combustion synthesis of Si3N4

This study addresses itself in the performance of Si₃N₄ combustion synthesis, occurred in the presence of Si₃N₄ and NH₄Cl powders in N₂ atmosphere of 6 MPa. Mechanochemical activation of Si powder, achieved via high-energy attrition milling up to 24 h, increases the intensity and the efficiency of the reactions between Si and N₂ as well as combustion temperature. Benign processing conditions, anticipated with lower mechanochemical activation of Si powder, low N₂ pressures, and low combustion temperatures, favor formation of α-Si₃N₄.     

Microstructure and mechanical characterization of Si3N4/nickel-based superalloy joints with Ti/Au/Ni interlayers

The Si₃N₄ ceramic was joined to nickel-based superalloy via partial transient liquid phase bonding with Ti/Au/Ni interlayers. The interfacial microstructure and strength of joints were examined by methods of scanning electron microscopy, transmission electron microscopy, X-ray diffraction and a three-point flexural test. The results revealed the joint between Si₃N₄ and Ni interlayer consisted of TiN layer, Au-rich phase, Ni-rich phase and tiny TiO phase. The highest flexural strength of 211?MPa was achieved at room temperature, and the high-temperature strength of joints reached up to 117?MPa when testing at 1073?K. Post-bonding treatment indicated the joint strength of 120?MPa was obtained after annealing in air at 1073?K for 100?h, which exhibited superior oxidation resistant.     

Luminescence properties of Eu activated Ba2Si5N8 red phosphors with various Eu contents

This study was carried out to characterize the crystal structure and luminescence properties of Eu²⁺ doped red-emitting Ba₂Si₅N₈ phosphor. In this research, Ba₂Si₅N₈ phosphors with various Eu compositions were prepared by normal pressure sintering (NPS). Ba₃N₂, Si₃N₄ and Eu₂O₃ were sintered at a high temperature in a mixture of N₂ and H₂. The crystal structure was analyzed by X-ray diffraction(XRD), and the photoluminescence(PL) properties of the Eu²⁺ - activated Ba₂Si₅N₈ phosphors were evaluated as a function of the Eu²⁺ activator concentration. The red-emitting Ba₂Si₅N₈ phosphors showed a broad excitation band range as well as high quantum output.     

TiO2 photocatalyst loaded on hydrophobic Si3N4 support for efficient degradation of organics diluted in water

TiO₂ photocatalyst loaded on Si₃N₄ (TiO₂/Si₃N₄) was prepared by a conventional impregnation method and its photocatalytic performance for the degradation of organics (2-propanol) diluted in water was compared with that of TiO₂ photocatalysts (TiO₂/SiO₂, TiO₂/Al₂O₃, and TiO₂/SiC) loaded on various types of supports (SiO₂, Al₂O₃, and SiC). The formation of the well-crystallized anatase phase of TiO₂ was observed on the calcined TiO₂/Si₃N₄ photocatalyst, while a small anatase phase of TiO₂ was observed on the TiO₂/SiC photocatalyst and amorphous TiO₂ species was the main component on the TiO₂/SiO₂ and TiO₂/Al₂O₃ photocatalysts. The measurements of the water adsorption ability of photocatalysts indicated that the TiO₂/Si₃N₄ photocatalyst exhibited more hydrophobic surface properties in comparison to other support photocatalysts. Under UV-light irradiation, the TiO₂/Si₃N₄ photocatalyst decomposed 2-propanol diluted in water into acetone, CO₂, and H₂O, and finally, acetone was also decomposed into CO₂ and H₂O. The TiO₂/Si₃N₄ photocatalyst showed higher photocatalytic activity than TiO₂ photocatalyst loaded on other supports. The well-crystallized TiO₂ phase deposited on Si₃N₄ and the hydrophobic surface of Si₃N₄ support are important factors for the enhancement of photocatalytic activity for the degradation of organic compounds in liquid-phase reactions.     

Coating Gd2O3:Eu phosphors with silica by solid-state reaction at room temperature

Silica coating on Gd₂O₃:Eu particles was obtained by a simple method, e.g. solid-state reaction at room temperature. The urea homogeneous precipitation method was used to synthesize the Gd₂O₃:Eu cores. Transmission electron microscopy (TEM) shows that the core particles are spherical with submicrometer size which is the soft agglomerates with nanometer crystallites. The TEM morphology of coated particles shows that a thin film is coated on the surface of Gd₂O₃:Eu cores. Scanning electron microscopy (SEM) and energy-dispersive spectrometer (EDS) analysis indicate that the coating of silica can be used to avoid agglomeration of Gd₂O₃:Eu particles to obtain smaller particles. X-ray photoelectron spectra (XPS) show that silica is coated on the surface of core particles by forming the chemical bond. Photoluminescence (PL) spectra conform that Gd₂O₃:Eu phosphors remain well-luminescent properties by the silica coating.     

Paper derived SiC–Si3N4 ceramics for high temperature applications

Biomorphic Si₃N₄–SiC ceramics have been produced by chemical vapour infiltration and reaction technique (CVI-R) using paper preforms as template. The paper consisting mainly of cellulose fibres was first carbonized by pyrolysis in inert atmosphere to obtain carbon bio-template, which was infiltrated with methyltrichlorosilane (MTS) in excess of hydrogen depositing a silicon rich silicon carbide (Si/SiC) layer onto the carbon fibres. Finally, after thermal treatment of this Si/SiC precursor ceramic in nitrogen-containing atmosphere (N₂ or N₂/H₂), in the temperature range of 1300–1450 °C SiC–Si₃N₄ ceramics were obtained by reaction bonding silicon nitride (RBSN) process. They were mainly composed of SiC containing α-Si₃N₄ and/or β-Si₃N₄ phases depending on the nitridation conditions. The SiC–Si₃N₄ ceramics have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and Raman spectroscopy. Thermal gravimetric analysis (TGA) was applied for the determination of the residual carbon as well as for the evaluation of the oxidation behaviour of the ceramics under cyclic conditions. The bending strength of the biomorphic ceramics was related to their different microstructures depending on the nitridation conditions.     

Improvement of the high temperature properties of the LiYO2–Si3N4 system by removing residual Li

Effects of the vaporization of residual Li on the microstructure, oxidation behavior and high temperature properties of a low-temperature pressureless sintered Si₃N₄ using LiYO₂ additive were investigated. The oxidation and creep resistance of the Si₃N₄ was improved after an annealing at 1650 °C because residual Li, which deteriorated the high temperature properties of the Si₃N₄, could be mostly removed. The high temperature deformation of the Si₃N₄ was strongly suppressed after the annealing treatment. The annealed specimens retained 64% of the room temperature strength at 1300 °C in air. The present investigation reports a method to improve the high temperature properties of Si₃N₄.     

Improved electrochemical performance of La0.7Sr0.3MnO3 and carbon co-coated LiFePO4 synthesized by freeze-drying process

Carbon coated LiFePO₄ particles were first synthesized by sol-gel and freeze-drying method. These particles were then coated with La_0.7Sr_0.3MnO₃ nanolayer by a suspension mixing process. The La_0.7Sr_0.3MnO₃ and carbon co-coated LiFePO₄ particles were calcined at 400 °C for 2 h in a reducing atmosphere (5% of hydrogen in nitrogen). Nanolayer structured La_0.7Sr_0.3MnO₃ together with the amorphous carbon layer forms an integrate network arranged on the bare surface of LiFePO₄ as corroborated by high-resolution transmission electron microscopy. X-ray diffraction results proved that the co-coated composite still retained the structure of the LiFePO₄ substrate. The twin coatings can remarkably improve the electrochemical performance at high charge/discharge rates. This improvement may be attributed to the lower charge transfer resistance and higher electronic conductivity resulted from the twin nanolayer coatings compared with the carbon coated LiFePO₄.     

In situ preparation of Si3N4–TiN composite by pyrolysis of polytitanosilazane (PTSZ)

Si₃N₄–TiN composite powders were obtained by in situ pyrolysis of polytitanosilazane. Dense Si₃N₄–TiN composites were prepared by hot-pressing at 1800 °C under 20 MPa for 2 h without sintering additive. Crystallization of amorphous PTSZ powders occurred between 1400 and 1500 °C with major phases, α-Si₃N₄, β-Si₃N₄, and small amount of phase TiN. Mechanical properties and microstructure of Si₃N₄–TiN composites were characterized. The results showed that the mechanical strength was 620 MPa, the fracture toughness was 7.8 MPa m^1/2 and the Vickers hardness was 8.5 GPa. SEM analysis indicated that Si₃N₄–TiN composite possessed excellent fracture toughness because TiN grains produced by in situ pyrolysis were well dispersed in Si₃N₄ matrix.     

C2H2 gas sensor based on Ni-doped ZnO electrospun nanofibers

Pure and Ni-doped ZnO nanofibers were synthesized using the electrospinning method. The morphology, crystal structure and optical properties of the nanofibers were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy, respectively. It is found that Ni doping does not change the morphology and crystal structures of the nanofibers, and the ultraviolet emissions of ZnO nanofibers present red shift with increasing Ni doping concentration. C₂H₂ sensing properties of the sensors based on the nanofibers were investigated. The results show that the C₂H₂ sensing properties of ZnO nanofibers are effectively improved by Ni doping, and 5 at% Ni-doped ZnO nanofibers exhibit a maximum sensitivity to C₂H₂ gas.     

Synthesis of carbon-free Si3N4/SiC nanopowders using silica fume

We have investigated a possible method of synthesizing carbon-free, nano-silicon nitride-silicon carbide (Si₃N₄/SiC) powders from the waste silica fume for the first time, using the integrated mechanical and thermal activation (IMTA) process. This novel process results in the formation of nano-Si₃N₄/SiC powders at 1465 °C with crystallite sizes as small as 45 nm. In order to synthesize carbon-free nano-Si₃N₄/SiC powders, two different approaches, one using the H₂ gas and the other using air, have been studied for their effectiveness in removing the free carbon present. It is found that the H₂ treatment is not very effective although both Si₃N₄ and SiC are stable during the H₂ treatment. In contrast, removing the free carbon using air is effective, and the limited oxidation of nano-Si₃N₄ and SiC can be achieved if the air treatment is terminated soon after the free carbon is eliminated. This study has provided a clear pathway and understanding for effectively synthesizing carbon-free, nano-Si₃N₄/SiC powders from the silica fume.     

Low-temperature pressureless sintering of Al2O3-SiC-Ni nanocermets in air environment

This paper introduces a simplified method for low-temperature pressureless sintering of Al₂O₃-Ni-SiC nanocermets in air environment. In this method, a thin and continuous Ni shell was coated on the surface of Al₂O₃ particles using electroless deposition method. The composite powders were subsequently compressed to prepare bulk specimens. By preventing the ceramic particles from direct contact during the densification of green specimens, sintering temperature of cermet materials was reduced from that of Al₂O₃ (>?1400?°C) to the range of Ni solid-phase sintering temperature. Furthermore, dissolution of a low amount of phosphorus in the composition of Ni coatings caused the further decrease of the sintering temperature to 800?°C. At such low temperatures, pressureless sintering of the cermets in the air environment was successfully performed instead of the common hot pressing process in a reducing atmosphere. Optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDS) and X-ray diffraction (XRD) characterizations indicated that the microstructure of such sintered samples consists of a continuous Ni network surrounding Al₂O₃ grains, without any structural defects or Ni oxidation. Furthermore, mechanical properties of the cermet materials were improved through reinforcement of the continuous Ni network by different amounts of SiC nanoparticles. The results showed that Al₂O₃-Ni-5?wt% SiC nanocermets sintered at 800?°C obtain the highest compressive strength of 242.5?MPa, hardness of 56.8 RA, and the lowest wear weight loss of 0.04?mg/m.     

Neural network modeling and analysis of gel casting preparation of porous Si3N4 ceramics

Based on orthogonal experimental results of porous Si₃N₄ ceramics by gel casting preparation, a three-layer back propagation artificial neural network (BP ANN) was developed for predicting the performances of porous Si₃N₄ ceramics. The results indicated that BP ANN was a very useful and accurate tool for the prediction and optimization of porous Si₃N₄ ceramics performances. By using the developed ANN model, the influences of the compositions on performances of porous Si₃N₄ ceramics were investigated, and some important conclusions were drawn as follows: for the flexural strength of Si₃N₄ ceramics, solid loading has an optimum value where can achieve a maximum value, and the optimum solid loading decreases with the increase of monomer content; the porosity of sintering body monotonically decreases with the increase of solid loading, and it increases with monomer content; the porosity of sintering body monotonically increases with the increase of the ratio of crosslinking agent to monomer.     

Matrix–filler interactions in polysilazane-derived ceramics with Al2O3 and ZrO2 fillers

Interactions between a poly(vinyl)silazane and Al₂O₃ or Y₂O₃-stabilised ZrO₂ fillers were studied during the fabrication of polysilazane-derived bulk ceramics in order to investigate the influence of oxide fillers on resulting properties. Specimens were produced by coating of the filler powders with the polysilazane, warm-pressing of the resulting composite powders, and pyrolytic conversion in flowing N₂ at various temperatures between 1000 °C and 1400 °C. Significant differences in densification were observed, depending on the filler used. Reactions between the polysilazane-derived matrix and Al₂O₃ or ZrO₂ at temperatures ≥1300 °C resulted in the formation of Si₅AlON₇ or ZrSiO₄, respectively. Reactivity in the polysilazane-derived component was a result of SiO₂ contamination caused primarily by adsorbed species on the filler particle surface. Knowledge of polysilazane/filler interface processes is found to be decisive for the prediction of properties such as shrinkage and porosity, which heavily influence performance of a material.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Joining of Si3N4 to Si3N4 using a AuPd(Co,Ni)–V filler alloy and the interfacial reactions

Au38.0–Pd28.0–Co18.0–Ni7.0–V9.0 (in wt%) alloy was designed as a filler for joining Si₃N₄. The filler alloy showed a contact angle of 77.2° on Si₃N₄ ceramic at 1473 K. The Si₃N₄/Si₃N₄ joint brazed with the rapidly-solidified filler foils at 1443 K for 10 min exhibits an average three-point bend strength of 320.7 MPa at room temperature and the strength values are 217.9 MPa and 102.9 MPa at 1073 K and 1173 K respectively. The interfacial reaction products were composed of V₂N and Pd₂Si, and the elements Co and Ni in the brazing alloy did not participate in the interfacial reactions. The coarse-network-like distribution of refractory Pd₂Si compound within the Au–Pd–Co–Ni alloy matrix throughout the joint contributes to the stable high-temperature joint strengths.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.