Effect of epoxidized soybean oil on mechanical properties of woven jute fabric reinforced aromatic and aliphatic epoxy resin composites

A systematic study was performed to describe the effect of epoxidized soybean oil (ESO) on storage modulus, glass transition temperature (T _g) and mechanical properties in epoxy resin composites reinforced by jute fabric. In addition to aromatic diglycidylether of bisphenol‐A (DGEBA) resin, a glycerol (GER)‐and a pentaerythritol (PER)‐based aliphatic resin was applied as base resin, which can be also synthesized from renewable feedstock. Based on strip tensile test results, the usual alkali treatment of jute fabric was avoided. By increasing the ESO‐content in aliphatic composites the T _g increases, whereas in case of DGEBA, it decreases. The results indicate that although ESO has a significant softening effect, the jute fiber‐reinforced DGEBA composite can be replaced without significant compromise in mechanical properties by a potentially fully bio‐based composite consisting of 25 mass% ESO‐containing aliphatic PER‐reinforced by jute fibers. POLYM. COMPOS., 38:884–892, 2017. © 2015 Society of Plastics Engineers     

Mechanical characterization of woven carbon fiber composites with poly(methyl methacrylate)–modified epoxy matrices

The influence of the modification of epoxy matrices with poly(methyl methacrylate) (PMMA) on the fracture behavior of composite laminates based on woven carbon fibers has been investigated. Three‐point flexural, short beam shear (SBS) and end‐notched flexural tests (ENF) have been carried out. Microstructural features have been investigated by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Dynamic mechanical thermal analysis of the different epoxy matrices and their corresponding composites shows the power of this technique for microstructural studies. Fracture behavior is compared with that shown by similar bifunctional (DGEBA) epoxy matrix composites. In spite of the two‐phase structure obtained in tetrafunctional (TGDDM) epoxy matrix‐based systems for all PMMA contents, only a small improvement in fracture toughness and interlaminar shear strength properties was obtained. In contrast, for DGEBA bulk matrices and composites, a higher enhancement of fracture toughness was obtained, as a consequence of the lower crosslink densities of bifunctional matrices.     

Electrically conductive composites based on epoxy resin containing polyaniline–DBSA‐ and polyaniline–DBSA‐coated glass fibers

Four kinds of polyaniline (PANI)‐coated glass fibers (GF–PANI) combined with bulk PANI particles were synthesized. GF–PANI fillers containing different PANI contents were incorporated into an epoxy–anhydride system. The best conductivity behavior of the epoxy/GF–PANI composites was obtained with a GF–PANI filler containing 80% PANI. Such a composite shows the lowest percolation threshold at about 20% GF–PANI or 16% PANI (glass fiber‐free basis). The PANI‐coated glass fibers act as conductive bridges, interconnecting PANI particles in the epoxy matrix, thus contributing to the improvement of the conductivity of the composite and the lower percolation threshold, compared with that of a epoxy/PANI–powder composite. Particularly, the presence of glass fibers significantly improves the mechanical properties, for example, the modulus and strength of the conductive epoxy composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1329–1334, 2004     

Enzyme‐mediated surface modification of jute and its influence on the properties of jute/epoxy composites

Surface modification of jute fibers is necessary to improve the adhesion and interfacial compatibility between fibers and resin matrix before using fibers in polymer composites. In this study, dodecyl gallate (DG) was enzymatically grafted onto the jute fiber by laccase to endow the fiber with hydrophobicity. A hand lay‐up technique was then adopted to prepare jute/epoxy composites. Contact angle and wetting time measurements showed that the surface hydrophobicity of the jute fabric was increased after the enzymatic graft modification. The water absorption and thickness swelling of the DG‐grafted jute fabric/epoxy composite were lower than those of the other composites. The tensile and dynamic mechanical properties of the jute/epoxy composites were enhanced by the surface modification. Scanning electron microscopy images revealed stronger fiber–matrix adhesion in composites with modified fibers. Therefore, the enzymatic graft modification increased the fiber–matrix interface area. The fiber–matrix adhesion was enhanced, and the mechanical properties of the composites were improved. POLYM. COMPOS., 38:1327–1334, 2017. © 2015 Society of Plastics Engineers     

Thermal,mechanical, and dielectric studies on the DGEBA epoxy blends by using liquid oxidized poly(1,2‐butadiene) as a reactive component

Liquid oxidized poly(1,2‐butadiene) (LOPB) with multi epoxy groups is synthesized to modify diglycidyl end‐caped poly(bisphenol A‐co‐epichlorohydrin) (DGEBA) cured by 4,4′‐diaminodiphenyl sulfone (DDS). FTIR spectra shows that DGEBA and LOPB can be effectively cured by DDS, and the epoxide rubber particles are evenly distributed in the composites till their addition up to 20 wt % of DGEBA as seen from the scanning electron microscope (SEM). Their decomposition temperatures (Td) increase with the increase in LOPB addition at around 10 wt % of DGEBA while the Td for the composite containing 20 wt % LOPB of DGEBA is lower than that of the neat epoxy. The addition of LOPB improves their storage moduli and especially these values at temperatures higher above 150 °C; all the composites exhibit higher glass transition temperature (T_g) than that of the neat epoxy, and the maximum T_g reaches up to 255 °C for the composite containing 15 wt % LOPB of DGEBA. The incorporation of LOPB effectively decreases their dielectric constants and the composite with 10 wt % LOPB of DGEBA possesses the lowest one. The synergic improvements in their various properties are attributed to the networks formation via covalent linkage between the two phases in these reactive blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44689.     

Mechanical and dynamic mechanical studies of epoxy/VAc‐EHA/HMMM IPN–jute composite systems

Epoxy [50:50 mixture of Di‐Glycidyl Ether of Bis‐Phenol A (DGEBA) and Epoxidized Novolac (EPN)] was solution blended with Vinyl Acetate‐2‐ Ethylhexylacrylate (VAc‐EHA) resin in aqueous medium, in varying weight fractions, with Hexamethoxymethylmelamine (HMMM) as a crosslinker and data was compared with a control. The present work was aimed to optimize the tensile strength, dynamic mechanical strength, impact strength, and toughness by preparing a blend followed by jute composites of a semi‐ and full interpenetrating network (IPN). In control experiments epoxy alone was crosslinked (semi‐IPN), whereas the DGEBA‐EPN and VAc‐EHA/HMMM were crosslinked separately (full‐IPN), using jute as the substrate for making composites. Composites of full‐IPN systems of epoxy/VAc‐EHA system had higher moduli and UTS than the semi‐IPN systems. Dynamic mechanical study showed that full‐IPN systems have higher T_g values than semi‐IPN systems. The impact strength increases with increasing proportions of VAc‐EHA copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 958–963, 2004     

Preparation and characterization of epoxidate poly(1,2‐butadiene)–toughened diglycidyl ether bisphenol‐A epoxy composites

By the oxidation of liquid poly(1,2‐butadiene) (LPB) with H₂O₂/HCOOH, epoxidate poly(1,2‐butadiene) (ELPB) was obtained as a toughening agent to prepare diglycidyl ether bisphenol‐A (DGEBA) epoxy composites by using V115 polyamide(PA) as a cross‐linking agent. DGEBA, ELPB, and the composites were effectively cured by PA at 100°C for 2 h followed by postcuring at 170°C for 1 h. Thermal gravimetric analysis results in air and nitrogen atmosphere showed that the thermal stability of composites could be improved by the addition of ELPB. Compared with DGEBA/PA, the composites exhibited a decrease in strength at yield but an increase in strain at break with the increase in ELPB amount. The composite with 10% ELPB exhibited both thermal stability and tenacity superior to those of DGEBA/PA and composites with 5 and 20% ELPB, respectively. The improvements in thermal and mechanical properties of composites depended on the formation of Inter Penetrating Networks (IPN) among DGEBA/PA/ELPB and their distributions in the matrix. At an appropriate ELPB amount, the IPN, mostly made of DGEBA/PA/ELPB, may be distributed more evenly in the matrix; less ELPB resulted in the formation of IPN mainly made of DGEBA/PA; excessive addition of ELPB resulted in the local aggregation of ELPB/PA and phase separations. The toughening mechanism was changed from chemically forming IPN made of DGEBA/PA/ELPB to physically reinforcing DGEBA/PA by ELPB/PA with the increase in ELPB addition. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical and morphological properties of carbon fiber reinforced–modified epoxy composites

Epoxy, prepared through aminomethyl 3,5,5‐trimethylcyclohexylamine hardening of diglycidylether of bisphenol‐A (DGEBA) prepolymer, toughened with polycarbonate (PC) in different proportions, and reinforced with carbon fiber, was investigated by differential scanning calorimetry, tensile and interlaminar shear strength testing, and scanning electron microscopy (SEM). A single glass transition temperature was found in all compositions of the epoxy/PC blend system. The tensile properties of the blend were found to be better than that of the pure epoxy matrix. They increased with PC content up to 10%, beyond which they decreased. The influence of carbon fiber orientation on the mechanical properties of the composites was studied, where the fiber content was kept constant at 68 wt %. Composites with 45° fiber orientation were found to have very weak mechanical properties, and the mechanical properties of the blend matrix composites were found to be better than those of the pure epoxy matrix composites. The fracture and surface morphologies of the composite samples were characterized by SEM. Good bonding was observed between the fiber and matrix for the blend matrix composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3529–3536, 2006     

Surface modification and physical properties of various UHMWPE‐fiber‐reinforced modified epoxy composites

Two surface modification methods—plasma surface treatment and chemical agent treatment—were used to investigate their effects on the surface properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers. In the analyses, performed using electron spectroscopy for chemical analysis, changes in weight, and scanning electron microscope observations, demonstrated that the two fiber‐surface‐modified composites formed between UHMWPE fiber and epoxy matrix exhibited improved interfacial adhesion and slight improvements in tensile strengths, but notable decreases in elongation, relative to those properties of the composites reinforced with the untreated UHMWPE fibers. In addition, three kinds of epoxy resins—neat DGEBA, polyurethane‐crosslinked DGEBA, and BHHBP‐DGEBA—were used as resin matrices to examine the tensile and elongation properties of their UHMWPE fiber‐reinforced composites. From stress/strain measurements and scanning electron microscope observations, the resin matrix improved the tensile strength apparently, but did not affect the elongation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 655–665, 2007     

Propylene‐ethylene copolymer nanocomposites: Epoxy resin grafted nanosilica as a reinforcing filler

In the present work it is shown that low nanoparticle‐loaded polymer composites with improved mechanical performance can be prepared by a conventional melt blending technique in which the nanoparticles are chemically pregrafted by diglycidyl ether of bisphenol‐A (DGEBA). Two composites, each with 2.5 wt% filler, were developed. The first one was obtained by melt blending propylene‐ethylene copolymer (EP) with nanosilica in a co‐rotating sigma internal mixer. The second one was obtained by melt blending the same EP, but with DGEBA grafted nanosilica. The addition of epoxy resin grafted nanosilica to the polymer matrix produced a homogeneous dispersion of particles in the form of micro domains. The results of tensile tests indicate that epoxy resin grafted nanosilica particles (SiO₂‐g‐DGEBA) provide EP with stiffening, strengthening, and toughening effects at a 2.5 wt% loading level. This is a much lower level compared to most particulate fillers used for composites. There was no noticeable improvement in the mechanical properties when nanosilica was added to the neat polymer. However, the addition of SiO₂‐g‐DGEBA particles to the polymer matrix led to an increase of both elastic modulus and toughness (from 0.36 to 0.54 GPa, and 19.06 to 21.05 MJ/m³, respectively). POLYM. ENG. SCI., 26:806–812, 2005. © 2005 Society of Plastics Engineers     

Synthesis and physicochemical study of bisphenol‐C‐formaldehyde‐toluene diisocyanate polyurethane–jute and jute–rice husk/wheat husk composites

Bisphenol‐C‐formaldehyde‐toluene‐2,4‐di isocyanate polyurethane (PU) has been synthesized at room temperature and used for the fabrication of jute and jute–rice husk/wheat husk hybrid composites. PU–jute and PU–jute–RH/WH composites were prepared under pressure of 30.4 MPa at room temperature for 8 h, while PU–jute–RH/WH composites were prepared under same pressure at 110°C for 5 h. PU–jute composite has good tensile strength and flexural strength (50–53 MPa), while PU–jute–RH/WH hybrid composites have moderate tensile strength (9–11 MPa) and a fairly good flexural strength (15–31 MPa). Composites possess 1.1–2.2 kV electric strength and 0.94–1.26 × 10¹² ohm cm volume resistivity. Water absorption in PU–jute composite is different in water (9.75%), 10% HCl (12.14%), and 10% NaCl (6.05%). Equilibrium water uptake time in salt environment is observed 96 h, while in pure water and acidic environments it is 192 h. In boiling water equilibrium water content and equilibrium time are found to be 21.7% and 3 h, respectively. Water absorption increased 2.2 times in boiling water, whereas equilibrium time reduced 64 times. Thus, PU–jute composite has excellent hydrolytic stability against boiling water, 10% HCl, and 10% NaCl solutions. Fairly good mechanical and electrical properties and excellent hydrolytic stability of composites signify their usefulness for low cost housing units and in electrical and marine industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2363–2370, 2006     

Influence of fiber modification on interfacial adhesion and mechanical properties of pineapple leaf fiber‐epoxy composites

Three kinds of surface treatment, that is, the alkalization (5% w/v NaOH aqueous solution), the deposition of diglycidyl ether of bisphenol A (DGEBA) from toluene solution (1% w/v DGEBA), and the alkalization combined with the deposition of DGEBA (5% w/v NaOH/1% w/v DGEBA) were applied to modify interfacial bonding and to enhance mechanical properties of pineapple leaf fiber (PALF) reinforced epoxy composites. The fiber strength and strain were measured by single fiber test and the fiber strength variation was assessed using Weibull modulus. Furthermore, a fragmentation test was used to quantify the interfacial adhesion of PALF‐epoxy composite. It was verified that the interfacial shear strength of modified PALFs was substantially higher than that of untreated PALF by almost 2–2.7 times because of the greater interaction between the PALFs and epoxy resin matrix. The strongest interfacial adhesion was obtained from the fibers that had been received the alkalization combined with DGEBA deposition. Moreover, the flexural and impact properties of unidirectional PALF‐epoxy composites were greatly enhanced when reinforced with the modified PALFs due to an improvement in interfacial adhesion, particularly in the synergetic use of 5% NaOH and 5% NaOH/1% DGEBA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and mechanical properties of unidirectional sisal– epoxy composites

Plant fibers are of increasing interest for use in composite materials. They are renewable resources and waste management is easier than with glass fibers. In the present study, longitudinal stiffness and strength as well as morphology of unidirectional sisal–epoxy composites manufactured by resin transfer molding (RTM) were studied. Horseshoe‐shaped sisal fiber bundles (technical fibers) were nonuniformly distributed in the matrix. In contrast to many wood composites, lumen was not filled by polymer matrix. Technical sisal fibers showed higher effective modulus when included in the composite material than in the technical fiber test (40 GPa as compared with 24 GPa). In contrast, the effective technical fiber strength in the composites was estimated to be around 400 MPa in comparison with a measured technical fiber tensile strength of 550 MPa. Reasons for these phenomena are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2358–2365, 2002     

A Comparative Study on the Mechanical Properties of Jute and Sisal Fiber Reinforced Polymer Composites

The aim of the present study is to investigate and compare the mechanical properties of raw jute and sisal fiber reinforced epoxy composites with sodium hydroxide treated jute and sisal fiber reinforced epoxy composites. This is followed by comparisons of the sodium hydroxide treated jute and sisal fiber reinforced composites. The jute and sisal fibers were treated with 20% sodium hydroxide for 2 h and then incorporated into the epoxy matrix by a molding technique to form the composites. Similar techniques have been adopted for the fabrication of raw jute and sisal fiber reinforced epoxy composites. The raw jute and sisal fiber reinforced epoxy composites and the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites were characterized by FTIR. The mechanical properties (tensile and flexural strength), water absorption and morphological changes were investigated for the composite samples. It was found that the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites exhibited better mechanical properties than the raw jute and raw sisal fiber reinforced composites. When comparing the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites, the sodium hydroxide treated jute fiber reinforced composites exhibited better mechanical properties than the latter.     

Impact toughness,viscoelastic behavior,and morphology of polypropylene–jute–viscose hybrid composites

In this investigation, we studied the impact toughness and viscoelastic behavior of polypropylene (PP)–jute composites. In this study, we used viscose fiber as an impact modifier and maleated PP as a compatibilizer. The toughness of the composites was studied with conventional Charpy and instrumental falling‐weight impact tests. The composites’ viscoelastic properties were studied with dynamic mechanical analysis. The results show that the incorporation of viscose fibers improved the impact strength and toughness to 134 and 65% compared to those of the PP–jute composites. The tan δ peak amplitude also increased with the addition of the impact modifier and indicated a greater degree of molecular mobility. The thermal stability of the composites was evaluated with thermogravimetric analysis. The addition of 2 wt % maleated polypropylene (MAPP) to the impact‐modified composite improved the impact strength and toughness to 144 and 93%, respectively. The fiber–matrix morphology of the fracture surface and the Fourier transform infrared spectra were also studied to ascertain the existence of the type of interfacial bonds. Microstructural analysis showed the retention of viscose fibers in the composites compared to the more separated jute fibers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42981.     

Role of gamma radiation and EGDMA on the physico–mechanical properties of jute fabrics/polypropylene composites

Jute fabrics reinforced polypropylene (PP) composites (45 wt % fiber) were prepared by compression molding and their mechanical properties were investigated. Both jute fabrics and PP sheets were treated with gamma radiation (250–1,000 krad dose) at a rate of 350 krad/h. Irradiated jute fabrics were soaked into ethylene glycol dimethacrylate (EGDMA) solutions (5–40% by weight) and cured in an oven at different temperatures (40–100°C) for 60 min. The percentage of polymer loading (PL) was evaluated and found that 20% EGDMA‐treated jute fabrics contains the highest PL. Composites made of 20% EGDMA‐treated jute fabrics were studied further. It was found that the treatment using the EGDMA improved the mechanical properties of the composites significantly. Scanning electron microscopy and aging properties of untreated and treated composites were performed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Synthesis and studies of the physical properties of polyaniline and polyurethane‐modified epoxy composites

Two series of toughened, semiconductive polyaniline (PANI)/polyurethane (PU)‐epoxy (PANI/PU‐EPOXY) nano‐composites were prepared using a conductive polymer, PANI, and PU prepolymer‐modified‐diglycidyl ether of bisphenol A (DGEBA) epoxy. First, the PU prepolymer‐modified epoxy oligomer was synthesized by a stoichiometric reaction between the terminal isocyanate groups of the PU prepolymer and the pendent hydroxyl groups of the epoxide. PU prepolymers were made either of polyester (polybutylene adipate, PBA) or polyether (polypropylene glycol, PPG) segments. The composites were characterized by thermal, morphological, mechanical, and electrical studies. Impact strength was enhanced 100% in PU (PPG 2000)‐modified composites; whereas, only ca. 30–50% increases in impact strength were observed for the other modified composites. In addition, the thermal stability of this composite proved superior to that of neat epoxy resin, regardless of a PU content at 27.5 wt%. Scanning electron microscopy (SEM) morphology study showed that the spherical PU (PPG 2000) particles (ca. 0.2–0.5 μm) dispersed within the matrix accounts for these extraordinary properties. The conductivity of the composite increased to ca. 10^?9–10^?3 S cm^?1 upon addition of PANI when tested in the frequency range 1 kHz–13 MHz. This study demonstrated a useful way to simultaneously improve the toughness and conductivity of the epoxy composite, thus rendering it suitable for electromagnetic interference and various charge dissipation applications. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Dynamic mechanical properties of particle‐reinforced EPDM composites

The dynamic mechanical property of particle‐reinforced ethylene–propylene–diene monomer (EPDM) matrix composites has been studied by using a dynamic mechanical thermal analyzer (DMTA). The individual composite has been reinforced with the various reinforcing particles as follows: silicon carbide particles (SiCps) of 60 μm in average diameter with various volume fractions (i.e., 10–40%); copper (Cu) and aluminum (Al) particles with 20 vol %; and SiCps with 6 and 36 μm in different average diameters with 20 vol % over the total composite volume. It is shown from the experimental results that the dynamic elastic modulus values increase and the composites with 40 vol % SiCps exhibit higher tan δ values through the entire rubbery phase after the glass transition region compared with the composites with lower particle volume percentages. This shows that the composites with 20 vol % Cu particles have the higher dynamic elastic modulus but the lower peak tan δ value than the composites with other particles of 20 vol % do. Scanning electron microscopy results show that the effective particle volume in the composite with Cu particles is higher than the other composites, although the same particle volume fraction of 20% has been used. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1595–1601, 2003     

An efficient fully bio‐based reactive diluent for epoxy thermosets: 2‐[(Oxiran‐2‐ylmethoxy) methyl] furan versus a petroleum‐based counterpart

Furfuryl alcohol and bio‐based epichlorohydrin were used to prepare a fully bio‐based reactive diluent, 2‐[(oxiran‐2‐ylmethoxy) methyl] furan (FOM). After spectral characterization, FOM was blended with epoxy resin, diglycidylether bisphenol A (DGEBA), at different ratios for reducing the viscosity. For a comparison, Cardura (one of the most common commercial reactive diluents), was separately incorporated to DGEBA. Amine‐curing process of the blends was recorded by FTIR and DSC. Similar trends of curing progression for DGEBA containing the reactive diluents were observed. Thermogravimetric analysis and dynamic mechanical thermal analysis, mechanical (hardness, adhesion, and stress–strain) and morphological properties were also investigated to study characteristics of the epoxy matrices formulated with FOM or Cardura. It was concluded that FOM could be considered as an efficient reactive diluent in formulations of polymer composites, structural adhesives and surface coatings based on epoxy resins. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44957.     

Study of jute fiber reinforced polyester composites by dynamic mechanical analysis

Cyanoethylation of jute fibers in the form of nonwoven fabric was studied, and these chemically modified fibers were used to make jute–polyester composites. The dynamic mechanical thermal properties of unsaturated polyester resin (cured) and composites of unmodified and chemically modified jute–polyester were studied by using a dynamic mechanical analyzer over a wide temperature range. The data suggest that the storage modulus and thermal transition temperature of the composites increased enormously due to cyanoethylation of fiber. An increase of the storage modulus of composites, prepared from chemically modified fiber, indicates its higher stiffness as compared to a composite prepared from unmodified fiber. It is also observed that incorporation of jute fiber (both unmodified and modified) with the unsaturated resin reduced the tan δ peak height remarkably. Composites prepared from cyanoethylated jute show better creep resistance at comparatively lower temperatures. On the contrary, a reversed phenomenon is observed at higher temperatures (120°C and above). Scanning electron micrographs of tensile fracture surfaces of unmodified and modified jute–polyester composites clearly demonstrate better fiber–matrix bonding in the case of the latter. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1505–1513, 1999