Morphology of polyimide fibers derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline

As one member of high performance fibers, aromatic polyimide fibers possess many advantages, such as high strength, high modulus, high and low temperature resistance, and radiation resistance. However, the preparation of the high performance fibers is so difficult that the commercial fibers have not been produced except P84 with good flame retardancy. In this report, a polyimide was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydianiline (ODA) and the fibers were prepared from its solution by a dry‐jet wet‐spinning process. The formation of the as‐spun fibers in different coagulation bath composition was discussed. Scanning electron microscope (SEM) was employed to study the morphology of the as‐spun fibers. As a result, the remnant solvent existed in the as‐spun fibers generated from coagulation bath of alcohol and water. There were many fibrils and microvoids with the dimension of tens of nanometers in the fibers. One could observe the obvious fibrillation and the drawn fibers. The measurement for the mechanical properties of the fibers with a drawing ratio of 5.5 indicated that tensile strength and initial modulus were 2.4 and 114 GPa, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 669–675, 2004     

Highly crystalline and oriented high‐strength poly(ethylene terephthalate) fibers by using low molecular weight polymer

High‐strength poly(ethylene terephthalate) (PET) fibers were obtained using low molecular weight (LMW) polymervia horizontal isothermal bath (hIB), followed by postdrawing process. We investigated the unique formations of different precursors, which differentiated in its molecular orientation and crystalline structures from traditional high‐speed spinning PET fibers. Sharp increase in crystallinity was observed after drawing process even though the fibers showed almost no any crystallinity before the drawing. Properties of as‐spun and drawn hIB and control filaments at different process conditions were compared. As would be expected, performances of resulted treated undrawn and drawn fibers have dramatically improved with developing unique morphologies. Tenacities more than 8 g/d for as‐spun and 10 g/d for drawn treated fibers after just drawn at 1.279 draw ratio were observed. These performances are considerably higher than that of control fibers. An explanation of structural development of high‐strength fibers using LMW polymer spun with hIB is proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42747.     

超高相对分子质量PPTA树脂及其高模量芳纶的研究

对高相对分子质量聚对苯二甲酰对苯二胺(PPTA)树脂进行了表征,开展了添加超高相对分子质量PPTA树脂与普通相对分子质量PPTA树脂共混进行液晶纺丝得到高强度和高模量芳纶的结构表征与性能试验,同时对芳纶的力学性能与其PPTA树脂相对分子质量的关系进行了研究。结果表明,芳纶的力学性能与其PPTA聚合体的相对分子质量紧密相关,如果PPTA树脂的相对分子质量不够高,加上液晶纺丝和高模量热处理过程分子链的进一步降解,高模量芳纶的制备就无法实现。在系统研究PPTA聚合反应规律,特别是聚合诱导相互转变规律及其影响因素研究基础上,通过调控连续聚合的反应条件,在1 000 t/a连续聚合生产线上制备出比浓对数粘度高达9.2 dl/g的超高相对分子质量PPTA树脂;用超高相对分子质量PPTA树脂与通用级PPTA树脂(比浓对数粘度6.8 dl/g)混合进行纺丝,制备出高强度的芳纶,并进一步热处理得到高强度和高模量的芳纶。     

Effects of water on drawability,structure, and mechanical properties of poly(vinyl alcohol) melt‐spun fibers

Poly(vinyl alcohol) (PVA) melt‐spun fibers with circular cross‐section and uniform structure, which could support high stretching, were prepared by using water as plasticizer. The effects of water content on drawability, crystallization structure, and mechanical properties of the fibers were studied. The results showed that the maximum draw ratio of PVA fibers decreased with the increase of water content due to the intensive evaporation of excessive water in PVA fibers at high drawing temperature. Hot drying could remove partially the water content in PVA as‐spun fibers, thus reducing the defects caused by the rapid evaporation of water and enhancing the drawability of PVA fibers at high drawing temperature. The decreased water content also improved the orientation and crystallization structure of PVA, thus producing a corresponding enhancement in the mechanical properties of the fibers. When PVA as‐spun fibers with 5 wt % water were drawn at 180 °C, the maximum draw ratio of 11 was obtained and the corresponding tensile strength and modulus reached ～0.9 GPa and 24 GPa, respectively. Further drawing these fibers at 215 °C and thermal treating them at 220 °C for 1.5 min, drawing ratio of 16 times, tensile strength of 1.9 GPa, and modulus of 39.5 GPa were achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45436.     

Structure and property changes of polyamide 6 during the gel‐spinning process

Polyamide 6 (PA6) gels were prepared by the dissolution of PA6 powder in formic acid with CaCl₂ as a complexing agent. The concentration of the polymer was 16% w/v. PA6 fibers were obtained through gel‐spinning, drawing, decomplexation, and heat‐setting processes. The structure and properties of the fibers at different stages were characterized with differential scanning calorimetry, thermogravimetric analysis, X‐ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. The experiment results indicate that the melting transition of the as‐spun fibers obtained by the extrusion of the PA6/CaCl₂/HCOOH solution into a coagulation bath through a die disappeared. A porous structure existed in the as‐spun fibers, which led to poor mechanical properties. Compared with the as‐spun fibers, the melting and glass‐transition temperatures of the decomplexed and drawn fibers retained their original values from PA6, the degree of crystallinity increased, the porous structure disappeared, and the mechanical properties were improved. The maximum modulus and tensile strength obtained from the drawn fibers in this study were 32.3 GPa and 530.5 MPa, respectively, at the maximum draw ratio of 10. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4449–4456, 2013     

High tensile strength fiber of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] processed by two‐step drawing with intermediate annealing

High tensile strength fibers of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] [P(3HB‐co‐3HH)], a type of microbial polyesters, were processed by one‐step and two‐step cold‐drawn method with intermediate annealing. Thermal degradation behaviors were characterized by differential scanning calorimeter and gel permeation chromatography measurements. Thermal analyses were revealed that molecular weights decreased drastically within melting time at a few minute. One‐step cold‐drawn fiber with drawing ratio of 10 showed tensile strength of 281 MPa, while tensile strength of as‐spun fiber was 78 MPa. When two‐step drawing was applied for P(3HB‐co‐3HH) fibers, the tensile strength was led to 420 MPa. Furthermore, the optimization of intermediate annealing condition leads to enhance the tensile strength at 552 MPa of P(3HB‐co‐3HH) fiber. Wide‐angel X‐ray diffraction measurements of these fibers suggest that the fibers with high tensile strength include much amount of the planer‐zigzag conformation (β‐form) as molecular conformation together with 2₁ helix conformation (α‐form). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41258.     

Direct drawing of gel fibers enabled by twist‐gel spinning process

A new twist‐gel spinning process for ultrahigh molecular weight polyethylene fibers is demonstrated which significantly increases the extraction rate of nonvolatile spin solvent while simultaneously reducing the consumption of extraction solvent by more than 75%. Applying twist to the gel fiber enables it to be directly hot‐drawn, allowing conventional solvent extraction to proceed significantly faster. While solvent extraction effectiveness is largely enhanced, the new process does not show reduced fiber properties. The tensile strength, Young's modulus, surface morphology, and geometry are relatively unaffected when compared to fibers produced using the conventional gel‐spinning process. The new twist‐gel spinning process is expected to improve the processing efficiency of gel‐spun high‐strength fibers, promoting broad expansion of these high performance fibers into applications that were previously prohibitive due to extremely slow production. POLYM. ENG. SCI., 55:1389–1395, 2015. © 2015 Society of Plastics Engineers     

The influence of drawing,twisting, heat setting,and untwisting on the structure and mechanical properties of melt-spun high-density polyethylene fiber

The variation of crystalline morphology and mechanical properties of polyethylene fibers was studied as they were sequentially melt spun, drawn, twisted, heat set, and untwisted. Twisting of as-melt spun fibers was also investigated. The morphology was characterized using wideangle x-ray diffraction, small-angle x-ray diffraction, and scanning electron microscopy techniques. Drawing results in high crystalline orientation, fibrillation, and large increases in modulus and tensile strength. Effects due to variation of spinning conditions were noted. Twisting either as-spun or drawn fibers decreased the axial orientation, modulus, tensile strength, and usually also the elongation to break. The changes in these properties increased with twist angle. Twisting also caused transformation of a small fraction of the sample to the monoclinic form of polyethylene. Heat setting caused healing of voids generated during drawing and increased the perfection and periodicity of the stacking of lamellar crystals along the fiber axis. Heat setting also caused the monoclinic polyethylene to transform back to the orthorhombic form, and it increased the modulus and tensile strength. Untwisting returned the orientation in the fiber to essentially that which it would have if it had not been twisted, but untwisting also resulted in the formation of kink bands.     

In situ modulus enhancement of polypropylene monofilament through blending with a liquid‐crystalline copolyester

An immiscible blend of poly(propylene) (PP) with a thermotropic liquid‐crystalline polymer (TLCP, trade name Rodrun LC5000), a copolyester of 80/20 mol ratio of p‐hydroxy benzoic acid and polyethylene terephthalate was prepared in a twin‐screw extruder. The blend extrudate was fabricated as monofilament by using a single‐screw extruder equipped with a fiber line. The as‐spun filament was drawn at 120°C to enhance molecular orientation. Morphology, thermal, tensile, and dynamic mechanical properties of both as‐spun and drawn monofilaments were investigated. Almost continuously long TLCP fibers dispersed in PP matrix were obtained in the composite as‐spun monofilaments. The maximum modulus was found in 15 wt % TLCP/PP composite as‐spun filament, an increase of about 2.4 times that of the as‐spun neat PP. For the drawn filaments, the 10 wt % TLCP/PP composite showed a maximum modulus, an increase of about 1.5 times that of the drawn neat PP. The increase in the moduli was attributed not only to the reinforcement by TLCP fibrils with very high aspect ratio but also to the increases in PP crystallinity and molecular orientation through the drawing process. A remarkable improvement in the dynamic mechanical properties of the composite monofilaments was observed, especially in the high‐temperature region. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90:1337–1346, 2003     

超高相对分子质量PET纤维的拉伸和热处理工艺

研究了超高相对分子质量ＰＥＴ纤维后拉伸和热处理工艺。结果表明,提高拉伸倍数和一定条件下的热处理可明显提高纤维的强度和模量,聚合体相对分子质量和纺丝浓度及拉伸温度对纤维的可拉伸性有重要影响。乙二醇作为一种热处理介质,可提高纤维强度和模量。增加热处理张力,可以明显地提高纤维的强度。     

Novel aromatic polyimide fiber with biphenyl side‐groups: Dope synthesis and filament internal morphology control

A new organic‐soluble aromatic polyimide with biphenyl side‐groups has been synthesized from 4,4′‐oxydiphthalic anhydride and 3,5‐diamino‐benzonic‐4′‐biphenyl ester (DABBE) via a one‐step polymerization in m‐cresol. A higher molecular weight polyimide has been obtained by the addition of chlorotrimethylsilane (TMSCl) in the solution of DABBE to form, in situ, silylated diamine. The optimum mole amount of TMSCl relative to the number of amino groups is 100%. This polyimide is soluble in m‐cresol, allowing fibers to be spun from isotropic solution using a dry‐jet wet spinning method. Based on a ternary phase diagram of m‐cresol, ethanol, and water, controlling of the internal morphology of as‐spun fibers has been achieved by varying the rate of polyimide coagulation through adjustment of nonsolvent/solvent miscibility in the coagulation bath. Scanning electron microscopic pictures show that filament internal morphologies ranged from porous‐like to fully solid. The solid as‐spun fibers can be drawn at high temperatures (>330°C) under tension to high drawn ratios (up to 6×), which produces a remarkable increase in tensile strength to about 1.0 GPa and an initial modulus higher than 60 GPa. POLYM. ENG. SCI. 46:123–128, 2006. © 2005 Society of Plastics Engineers     

Processing,structure, and properties of gel spun PAN and PAN/CNT fibers and gel spun PAN based carbon fibers

Polyacrylonitrile (PAN) and PAN/carbon nanotube (PAN/CNT) fibers were manufactured through dry‐jet wet spinning and gel spinning. Fiber coagulation occurred in a solvent‐free or solvent/nonsolvent coagulation bath mixture with temperatures ranging from ?50 to 25°C. The effect of fiber processing conditions was studied to understand their effect on the as‐spun fiber cross‐sectional shape, as well as the as‐spun fiber morphology. Increased coagulation bath temperature and a higher concentration of solvent in the coagulation bath medium resulted in more circular fibers and smoother fiber surface. as‐spun fibers were then drawn to investigate the relationship between as‐spun fiber processing conditions and the drawn precursor fiber structure and mechanical properties. PAN precursor fiber tows were then stabilized and carbonized in a continuous process for the manufacture of PAN based carbon fibers. Carbon fibers with tensile strengths as high as 5.8 GPa and tensile modulus as high as 375 GPa were produced. The highest strength PAN based carbon fibers were manufactured from as‐spun fibers with an irregular cross‐sectional shape produced using a ?50°C methanol coagulation bath, and exhibited a 61% increase in carbon fiber tensile strength as compared to the carbon fibers manufactured with a circular cross‐section. POLYM. ENG. SCI., 55:2603–2614, 2015. © 2015 Society of Plastics Engineers     

Two‐stage drawing process to prepare high‐strength and porous ultrahigh‐molecular‐weight polyethylene fibers: Cold drawing and hot drawing

High‐strength and porous ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers have been prepared through a two‐stage drawing process. Combined with tensile testing, scanning electron microscopy, and small‐angle X‐ray scattering, the mechanical properties, porosity, and microstructural evolution of the UHMWPE fibers were investigated. The first‐stage cold drawing of the gel‐spun fibers and subsequent extraction process produced fibers with oriented lamellae stacks on the surface and plentiful voids inside but with poor mechanical properties. The second‐stage hot drawing of the extracted fibers significantly improved the mechanical properties of the porous fibers because of the formation of lamellar backbone networks on the surface and microfibrillar networks interwoven inside to support the voids. With various processing conditions, the optimized mechanical properties and porosity of the prepared UHMWPE fibers were obtained a tensile strength of 1.31 GPa, a modulus of 10.1 GPa, and a porosity of 35%. In addition, a molecular schematic diagram is proposed to describe structural development under two‐stage drawing, including void formation and lamellar evolution. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42823.     

PVA凝胶纺丝工艺对纤维结构与性能的影响

讨论了聚乙烯醇（ＰＶＡ）凝胶纺丝过程中的凝固浴、初生冻胶丝的溶剂萃取和干燥收缩以及干冻胶丝超拉伸、热定型等工艺条件对ＰＶＡ纤维结构和性能的影响，并制备出拉伸强度和模量分别为１１．３和４３０ｃＮ／ｄｔｅｘ的高强高模ＰＶＡ纤维。     

Spinning and drawing properties of ultrahigh‐molecular‐weight polyethylene fibers prepared at varying concentrations and temperatures

The concentrations and temperatures of ultrahigh‐molecular‐weight polyethylene (UHMWPE) gel solutions exhibited a significant influence on their rheological and spinning properties. The shear viscosities of UHMWPE solutions increased consistently with increasing concentrations at a constant temperature above 80°C. Tremendously high shear viscosities of UHMWPE gel solutions were found as the temperatures reached 120–140°C, at which their shear viscosity values approached the maximum. The spinnable solutions are those gel solutions with optimum shear viscosities and relatively good homogeneity in nature. Moreover, the gel solution concentrations and spinning temperatures exhibited a significant influence on the drawability and microstructure of the as‐spun fibers. At each spinning temperature, the achievable draw ratios obtained for as‐spun fibers prepared near the optimum concentration are significantly higher than those of as‐spun fibers prepared at other concentrations. The critical draw ratio of the as‐spun fiber prepared at the optimum concentration approached a maximum value, as the spinning temperature reached the optimum value of 150°C. Further investigations indicated that the best orientation of the precursors of shish‐kebab‐like entities, birefringence, crystallinity, thermal and tensile properties were always accompanied with the as‐spun fiber prepared at the optimum concentration and temperature. Similar to those found for the as‐spun fibers, the birefringence and tensile properties of the draw fibers prepared at the optimum condition were always higher than those of drawn fibers prepared at other conditions but stretched to the same draw ratio. Possible mechanisms accounting for these interesting phenomena are proposed.     

Melt spinning of high‐strength fiber from low‐molecular‐weight polypropylene

Polypropylene (PP) with high melt flow index (MFI) or low molecular weight, although desired in melt spinning for enhanced productivity, is difficult to be spun into high‐strength fiber using the standard process where extensive jet stretching is applied. In this work, a processing route involving minimal jet stretch has been explored. A two‐stage hot drawing procedure in the solid state was found to be suitable for producing high‐strength fiber from low‐molecular‐weight PP with an ultrahigh MFI of 115 g/10 min. Fibers produced achieve a maximum tensile strength and Young's modulus of approximately 600 MPa and 12 GPa, respectively. The melt temperature of the fiber reached 170.8°C, approximately 5°C higher than that of the original resin. Wide‐angle X‐ray diffraction (WAXD) study shows that the stable α‐monoclinic crystalline structure is developed during the drawing process. A well‐oriented crystalline structure along the fiber axis is generated, having a crystalline orientation factor as high as 0.84. POLYM. ENG. SCI., 56:233–239, 2016. © 2015 Society of Plastics Engineers     

Preparation of poly(lactic acid) fiber by dry‐jet‐wet‐spinning. I. Influence of draw ratio on fiber properties

Poly(lactic acid) fiber was prepared by dry‐jet‐wet spinning of the polymer from chloroform solution and with methanol as the precipitating medium. The as‐spun fiber was subsequently made into high strength fiber by two‐step process of drawing at a temperature of 90°C and subsequent heat setting in the temperature range of 120°C. The draw ratio had significant influence on the crystallinity and the tensile strength of the fiber. The fiber with the tenacity of 0.6 GPa and modulus of 8.2 GPa was achieved at a draw ratio of 8. The differential scanning calorimetry revealed an increase in the glass‐transition temperature with the increase in the draw ratio, which suggests the orientation of chains during the drawing process. The surface morphology of the filament as revealed by scanning electron microscopy shows that fibers are porous in nature, but a significant reduction in the porosity and pore size of the fiber was observed with the increase in the draw ratio. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1239–1246, 2006     

Preparation and properties of poly(ε‐caprolactone) self‐reinforced composites based on fibers/matrix structure

Self‐reinforced poly(ε‐caprolactone) (PCL) composites were prepared from bi‐component PCL yarns composed of PCL drawn fibers and PCL matrix by a combined process of yarns winding and hot‐pressing. Series of PCL polymers with different melting points were synthesized and used as matrix. PCL melt‐spun fibers were subject to different draw ratios and functioned as reinforcement. During the process of hot‐pressing, the matrix with low melting points melted and bonded the unmelted drawn fibers together creating self‐reinforced composites, the morphologies of which were examined by scanning electron microscope. Tensile testing of the composites was performed along the longitudinal and transverse directions separately. The longitudinal tensile test results showed that the Young's modulus and strength at break of the self‐reinforced composites were 59% and 250% higher than that of pure PCL. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44673.     

Controlling of threadline dynamics via a novel method to develop ultra‐high performance polypropylene filaments

A detailed study was conducted to investigate the effects of horizontal isothermal bath (hIB) on the production of ultra‐high performance polypropylene filaments. Two different commercial PP polymers were used with the melt flow rate of 4.1 and 36 g/10 min. The optimum process conditions depended on polymer molecular weight. Fibers showed distinct precursor morphology for each at each optimum process condition. However, two sets of filaments demonstrated similar fiber tenacity and modulus of about 7 and 75 g d^?1, respectively, for as‐spun and more than 12 g d^?1 for tenacity and more than 190 g d^?1 for modulus values of drawn fibers after just 1.49 draw ratio. The mean value for the modulus after the drawing process for the high melt flow rate was 196 g d^?1. The theoretical modulus of PP is 35–42 GPa¹⁹, (275–330 g d^?1), shows the hIB fiber's modulus performance is approaching its theoretical maximum value. Fibers had greatly improved thermal properties, degree of crystallinity, crystalline and amorphous orientation factors. The hIB spinning system produced highly oriented and predominantly amorphous structure for as‐spun fibers and a well‐defined, highly oriented crystalline fibrillar and amorphous structure after drawing process with the draw ratios lower than 1.5. POLYM. ENG. SCI., 55:327–339, 2015. © 2014 Society of Plastics Engineers     

High strength polyethylene fibers from high density polyethylene/organoclay composites

High strength fibers were prepared from high density polyethylene (HDPE)/organically modified montmorillonite (OMMT) composites. X‐ray diffraction study revealed that the composites were of conventional or phase‐separated type. As‐spun composite fibers were found to have higher drawability than as‐spun HDPE fiber. As a result of an increased drawability, fibers with much higher mechanical properties were obtained. The highest modulus and tensile strength obtained in the present study were 38 GPa and 1.7 GPa, respectively. Study of internal morphology suggests that the role of OMMT is to suppress a defect formation and allows the fiber to be drawn to higher draw ratio. Analysis of the mechanical properties of the fibers using a Griffith type relationship suggested that the fibers have much smaller defects and the predicted attainable strength for the fiber is much higher than that previously predicted for melt‐spun and hot drawn fiber. POLYM. ENG. SCI., 47:943–950, 2007. © 2007 Society of Plastics Engineers