Multiphase zinc and magnesium mono-substituted calcium phosphates derived from cuttlefish bone: A multifunctional biomaterials

Biomimetic calcium phosphate (CaP) systems mono-substituted with zinc (Zn²⁺) and magnesium (Mg²⁺) ions were prepared from a biogenic source (cuttlefish bone) by wet precipitation method. The results revealed that the as-prepared powders were composed of calcium-deficient carbonated hydroxyapatite (HAp), octacalcium phosphate (OCP), and amorphous calcium phosphate (ACP), while the heat-treated powders consisted of HAp, α-tricalcium phosphate (α-TCP), and β-tricalcium phosphate (β-TCP). In addition to Zn²⁺ and Mg²⁺ ions, the presence of CO₃^2?, Sr²⁺ and Na ⁺ ions was detected with elemental analysis, which can be attributed to the use of cuttlefish bone as a natural precursor of Ca²⁺ ions. The data obtained by XRD study demonstrated the decrease in lattice parameters in the OCP and β-TCP phases for Zn-substitution and Mg-substitution in the HAp, OCP, and β-TCP phases. Zn²⁺ occupies the Ca(1,3,4,6,7,8) sites in OCP and Ca(1,2,3,4) sites in β-TCP, while Mg²⁺ occupies the Ca(2) sites in HAp and the Ca(4,5) sites in β-TCP. Phase transformation study under simulated physiological conditions for 7 days showed the transformation of OCP and ACP into the thermodynamically more stable HAp. Characterization of the zeta-potential showed positively charged populations for all prepared CaP powders, while all samples showed high bovine serum albumin adsorption capacity. The culture of human embryonic kidney cells showed that the prepared CaPs are non-cytotoxic and that viability of the cells increases during the culture period. All powders obtained showed antibacterial activity towards Gram-negative Escherichia coli and low antibacterial effect against Gram-positive Staphylococcus aureus, as determined by viability analysis during 48 h. Inhibition zone analysis and observation of the morphology after 24 h showed no antibacterial properties.     

MG63 osteoblast cell response on Zn doped hydroxyapatite (HAp) with various surface features

The clinical success of implant is governed by implant-surface and bone cell interaction that promote osseointegration and long term stability. Calcium hydroxyapatite (HAp) is a widely used bioceramic material for orthopedic and dental applications, which promotes bone tissue generation. Doped hydroxyapatite using various metallic ions is often reported to enhance this osteoconductive property. The objective of this study was to synthesize zinc doped HAp, to investigate the osteoblast cell response on this doped HAp and find out separately the effect of doping and different surface parameters on cell response. Slip casting technique was used to prepare pure and doped HAp specimens which were sintered at 1100 °C and 1250 °C. Different porosities, pore sizes were generated along with different surface roughness so as to understand the effect of these extrinsic parameters on cell culture. MG63 osteoblast cells were used for a maximum period of two weeks. Metabolic activity, adhesion and proliferation rate study of osteoblast cells on doped HAp showed significantly better response than pure HAp. Effect of doping was found to be more prominent than the effect of surface roughness.     

Synthesis of Eu-doped hydroxyapatite whiskers and fabrication of phosphor layer via electrophoretic deposition process

Highly biocompatible and efficiently luminescent whiskers of the hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, HAp) doped with various concentrations (0-5 at.%) of europium were prepared by hydrothermal synthesis and the Eu-doped Hap-coating layers onto the surface of titanium substrate were fabricated by the electrophoretic deposition (EPD) process for fluorescent probe application. The maximum doping concentration of Eu accommodating into the host lattice of HAp was detected as ~1.5 at.% and all the hydrothermally synthesized Eu-doped HAp whiskers were found to have high crystallinity and orientation growth along the c-axis by X-ray diffraction (XRD) identification. The valence of the doped Eu was identified as trivalent and divalent coexistence at a concentration percentage of Eu³⁺: Eu²⁺ = 78%: 22% by X-ray photoelectron spectroscopy (XPS) spectra. The replacement site of the doped Eu ions in the crystal structure of HAp host was clarified by Rietveld refinement. The whisker morphology of the hydrothermally synthesized particle was demonstrated by field-emission scanning electron microscopy (FE-SEM) observation and their component elements were analyzed by energy dispersive X-ray (EDX) mapping. The photoluminescence (PL) emissions of the Eu-doped HAp whiskers and fabricated their coating layers were both revealed mainly at ~615 nm (⁵D₀ → ⁷F₂) and ~697 nm (⁵D₀ → ⁷F₄), which is a wavelength that easily transmitting through living system for biological imaging. The PL emission are falling in the region of reddish orange and belonging to color temperature below 1500 K. Decay time and internal and external quantum efficiencies (QEs) were also measured to reveal them depending on the doping concentration of Eu. The hydrothermally prepared Eu-doped HAp whiskers would be aimed at biomedical application, due to their promising fluorescent function of probe for in vivo imaging in medical diagnose by utilizing the superior biocompatibility of the HAp host and highly efficient luminescent property of the Eu activator.     

Processing of hydroxyapatite and its composites using ceramic fused filament fabrication (CF3)

In this article, we report the fabrication of hydroxyapatite (HAp) and its composites with 7.75 vol% Si₃N₄ (HAp10SN) using ceramic fused filament fabrication (CF³). Homogeneous feedstock with 40 vol% ceramic powder was prepared and used to extrude filaments for further printing using a desktop printer. Our results showed that the addition of Si₃N₄ to HAp increases the feedstock viscosity. However, the filaments and CF³ parts made using HAp and HAp10SN feedstocks exhibited comparable densities without gross defects. We have obtained relatively smoother CF³ parts with HAp10SN than pure HAp, which is attributed to their high feedstock viscosity and formation of liquid phase during sintering. Sintering at 1250 °C for 4 h in air, after thermal debinding, resulted in a relative density of ~85% with HAp and tricalcium phosphate (TCP) as major constituents. Sintered HAp10SN samples also revealed almost 70% reduction in the grain size and 4-fold increase in the hardness compared to pure HAp. Our results indicate that the CF³ processed HAp10SN samples containing ~15% porosity, Si₃N₄ particles and Si-substituted HAp/TCP have strong potential as bone replacements.     

Optimizing liquid phase promotion effect by modifying powder specific surface area in Si4+/Mg2+ co-doped transparent Yb:YAG ceramics

Utilizing the Si⁴⁺/Mg²⁺ co-doping has been considered an effective approach to fabricate highly transparent ceramics. However, the optimum doping concentration has been reported with considerable uncertainties. In this work, highly transparent Yb:YAG ceramics were obtained via the solid-state method and the sintering behavior is discovered to be closely related to both the doping concentration of Si⁴⁺/Mg²⁺ and the specific surface area (S_BET) of powders. S_BET is effectively modified by setting the ball-milling time, where the maximum S_BET (30.914 m²/g) is achieved with 24 h ball-milling time. With increasing S_BET, less Mg²⁺ is required for better optical properties. When S_BET equals 30.914 m²/g, the highest in line transmittance @ 1100 nm of 84.85% is obtained with Si⁴⁺/Mg²⁺ doping concentrations of 0.50 wt% and 0.05 wt%, respectively. The relation between S_BET and optimum doping concentration is explained by the different magnitudes of liquid phase promotion required for different contact areas between powder particles.     

Increase ionic conductivity of a Zn2+/F− synergy Na3Zr2Si2PO12 solid electrolyte for sodium metal batteries

Na₃Zr₂Si₂PO₁₂ (NZSP) solid-state electrolyte is considered one of the most promising solid-state electrolyte because of their excellent electrochemical and thermal stability. Even though, the low conductivity of NZSP solid-state electrolytes hinders practical application. Therefore, an anions/cations co-assisting strategy is proposed by introducing the Zn²⁺ and F⁻. The influence of adding different amounts of Zn²⁺ and F⁻ on the Na⁺ conductivity of NZSP was investigated computationally and experimentally. The Zn²⁺/F⁻ co-assisting (Na_3.3Zr_1.85Zn_0.15Si₂PO₁₂) solid-state electrolyte exhibits the ionic conductivity of 0.722 mS cm⁻¹ at 30 °C, and the activation energy of ∼0.237 eV. Its applicability in a solid-state battery is tested, and the assembled Na/Na₃V₂(PO₄)₃ (NVP) battery exhibits an outstanding electrochemical performance of 98.4% capacity retention after being cycled at 0.5 C. Moreover, DFT calculations also have been used to demonstrate the effect of doping on the crystal structure and space migration energy barrier. This research provides new ideas for improving the electrochemical properties of inorganic solid electrolytes.     

Preferential occupancy of metal ions in the hydroxyapatite solid solutions synthesized by hydrothermal method

The solid solutions in the systems of Ca-Cd HAp [Ca_10−xCd_xHAp (x = 0–10)], Ca-Sr HAp [Ca_10−xSr_xHAp (x = 0–10)] and Ca-Pb HAp [Ca_10−xPb_xHAp (x = 0–10)], were successfully synthesized at 200 °C for 12 h under hydrothermal conditions. The site of the metal ions in the solid solutions was analyzed by the Rietveld method. The results of the Rietveld analysis indicated that the metal ions of Pb²⁺, Sr²⁺, and Cd²⁺ all preferentially occupied M (2) sites in the apatite structure. The preferential occupancy of the metal ions in M (2) sites were explained mainly by their ionic radius and electronegativity.     

Type-A zeolites with hydroxyapatite surface layers formed by an ion exchange reaction

To enhance adsorption of harmful ions on type-A zeolites (LTA), hydroxyapatite (HAp) thin layers were synthesized on the LTA surface by an ion exchange reaction of Ca²⁺ for NH₄⁺ under hydrothermal treatment. The temperatures and durations in the reactions were varied ranging from 25 to 200 °C and from 1 to 168 h. The samples synthesized were characterized by X-ray diffraction method (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer–Emmet–Teller method (BET). The structure of LTA was not destroyed by the hydrothermal treatments at 25 to 160 °C for 8 h and also at 120 °C for 1 to 72 h. The yield of HAp grown on the LTA surface, synthesized at 120 °C for 8 h, showed a maximum value of 0.82. The morphologies of HAp were dependent mainly on the temperatures. The specific surface area remained unchanged in the treatments at 25 to 40 °C for 8 h, as compared to the specific surface area of Ca-LTA, however up to 80 °C, the value decreased with an increase of exchange temperature.     

Theoretical prediction on structure evolution and optimal properties of silicon modified hexagonal boron nitride as interphase in SiCf/SiC composite

To predict the effects of Si doping on hexagonal boron nitride (h-BN) and to achieve a balance between mechanical and oxidation properties for the interphase modification in SiC_f/SiC composites, we herein calculate and analyze the crystal structures and mechanical properties of (BN)₆₄Si_x (x = 4, 8, 16, 32) models by means of density functional theory (DFT) calculations and ab initio molecular dynamics (aiMD) simulations. The possible trends of crack deflection and self-healing ability are discussed. The modeling shows an obvious transition of (BN)₆₄Si_x from the layered crystal structure and anisotropic mechanical property to amorphous structure and isotropic mechanical property as the Si doping content up to 36.1 wt%. Regarding to the application of interphase in SiC_f/SiC composites, (BN)₆₄Si₁₆ model structure possess the highest debonding potential according to Cook and Gordon’s criteria and illustrates the higher self-healing capacity at elevated temperature.     

Enhanced electrical properties of In-Ga-Sn-O thin films at low-temperature annealing

Electrical and optical properties of In-Ga-Sn-O (IGTO) thin films deposited by radio-frequency magnetron sputtering were investigated according to annealing temperatures. While IGTO films remained an amorphous phase even after a heat treatment at temperature up to 500 °C, Hall measurements showed that annealing temperature had a significant impact on electrical properties of IGTO thin films. After investigating a wide range of annealing temperatures for samples from as-deposited state to 500 °C, IGTO film annealed at 200 °C exhibited the best electrical performance with a conductivity of 229.31 Ω^?1cm^?1, a Hall mobility of 36.89 cm²V^?1s^?1, and a carrier concentration of 3.85 × 10¹⁹ cm^?3. Changes in proportions of oxygen-related defects and percentages of Sn²⁺ and Sn⁴⁺ ions within IGTO films according to annealing temperatures were analyzed with X-ray photoelectron spectroscopy to determine the cause of the superb performance of IGTO at a low temperature. In IGTO films annealed at 200 °C, Sn⁴⁺ ions acting as donor defects accounted for a high percentage, whereas hydroxyl groups working as electron traps showed a significantly reduced percentage compared to the as-deposited film. Optical band gaps of IGTO films obtained from UV–visible spectrum were 3.38–3.47 eV. The largest band gap value of 3.47 eV for the IGTO film annealed at 200 °C could be attributed to an increase in Fermi-level due to an increase of carrier concentration in the conduction band. These spectroscopic results well matched with electrical properties of IGTO films according to annealing temperatures. Excellent electrical properties of IGTO thin films annealed at 200 °C could be largely due to Sn donors besides oxygen vacancies, resulting in a significant increase in free carriers despite a low annealing. temperature.     

Diopside–Ca-Tschermak clinopyroxene based glass–ceramics processed via sintering and crystallization of glass powder compacts

The suitability of three new glass compositions for producing diopside–Ca-Tschermak clinopyroxene based glass–ceramics (GCs) was investigated. With respect to the formula of diopside, the first investigated composition resulted from the substitution 0.2(Si⁴⁺ + Mg²⁺) ↔ 0.4 Al³⁺, which leads to a composition of 80 mol.% diopside and 20 mol.% Ca-Tschermak. The substitutions in the second compositions were 0.25(Ca²⁺ + Si⁴⁺) ↔ 0.25(Y³⁺ + B³⁺) and 0.2(Si⁴⁺ + Mg²⁺) ↔ 0.4Al³⁺, and in the third composition 0.2Ba²⁺ ↔ 0.2Ca²⁺ and 0.2(Si⁴⁺ + Mg²⁺) ↔ 0.2(B³⁺ + Al³⁺). The influence of these substitutions on glass crystallization and the properties of the GCs produced between 850 and 1000 °C was experimentally investigated. The experimental results showed that the easily cast glasses, after melting at 1580 °C for 1 h, are prone to surface crystallization. Augite is predominantly crystallized, but Ca- and Ba-aluminosilicates can also form, according to the substitutions. The stability of the assemblage of the crystalline phases over a wide temperature range (850–1000 °C) and prolonged heat treatment (up to 50 h) and the properties of the produced GCs indicate a high potential of these compositions for several functional applications.     

Red-emitting enhancement of Bi4Si3O12:Sm3+ phosphor by Pr3+ co-doping for White LEDs application

In this account, Bi₄Si₃O₁₂:Sm³⁺ and (Bi₄Si₃O₁₂:Sm³⁺, Pr³⁺) red phosphors were prepared by solution combustion method fueled by citric acid at 900 °C for 1 h. The effects of co-doping Pr³⁺ ions on red emission properties of Bi₄Si₃O₁₂:Sm³⁺ phosphors, as well as the mechanism of interaction between Sm³⁺ and Pr³⁺ ions were investigated by various methods. X-ray diffraction (XRD) and Scanning electron microscopy (SEM) revealed that smaller amounts of doped rare earth ions did not change the crystal structure and particle morphology of the phosphors. The photoluminescence spectroscopy (PL) indicated that shape and position of the emission peaks of (Bi₄Si₃O₁₂:Sm³⁺, Pr³⁺) phosphors excited at λ_ex=403 nm were similar to those of Bi₄Si₃O₁₂:Sm³⁺ phosphors. The strongest emission peak was recorded at 607 nm, which was attributed to the ⁴G_5/2→⁶H_7/2 transition of the Sm³⁺ ion. The photoluminescence intensities of Bi₄Si₃O₁₂:Sm³⁺ phosphors were significantly improved by co-doping with Pr³⁺ ions and were maximized at Sm³⁺ and Pr³⁺ ions doping concentrations of 4 mol% and 0.1 mol%, respectively. The characteristic peaks of Sm³⁺ ions were displayed in the emission spectra of (Bi₄Si₃O₁₂:Sm³⁺, Pr³⁺) phosphors excited at respectively λ_ex=443 nm and λ_ex=481 nm (Pr:³H₄→³P₂, ³H₄→³P₀). This indicated the existence of Pr³⁺→Sm³⁺ energy transfer in (Bi₄Si₃O₁₂:Sm³⁺, Pr³⁺) phosphors.     

Calcium-magnesium-alumina-silicate (CMAS) resistant Ba2REAlO5 (RE = Yb,Er, Dy) ceramics for thermal barrier coatings

Calcium-magnesium-alumina-silicate (CMAS) attack has been a great challenge for the application of thermal barrier coatings (TBCs) in modern turbine engines. In this study, a series of prospective TBC candidate materials, Ba₂REAlO₅ (RE = Yb, Er, Dy), are found to have high resistance to CMAS attack. The rapid formation of a continuous crystalline layer on sample surface contributes to this desirable attribute. At 1250 °C, Ba₂REAlO₅ dissolve in the molten CMAS, accumulating Ba, RE and Al in the melt, which could trigger the crystallization of celsian, apatite and wollastonite crystals. Especially, the formation of the crystalline layer in the Ba₂DyAlO₅ sample is the fastest. This study also reveals that Ba is a useful element for altering CMAS composition to precipitate celsian. Thus, doping Ba²⁺ in yttria partially stabilized zirconia or other novel TBCs might be an attractive way of mitigating CMAS attack.     

High corrosion resistance of magnesium coated with hydroxyapatite directly synthesized in an aqueous solution

Anticorrosion coatings are crucial for practical applications of magnesium alloys, which are used to reduce the weight of vehicles, aircraft, electronics enclosures etc. Hydroxyapatite (HAp) potentially offers high corrosion resistance and no environmental toxicity because its thermodynamic structural stability is high and it is a basic component of bone. However, direct synthesis of HAp on magnesium in aqueous solutions has been a scientific challenge because Mg ions prevent HAp crystallization. A new method of direct synthesis of HAp on magnesium was developed using a Ca chelate compound, which can maintain a sufficiently high concentration of Ca ions on the magnesium surface to overcome prevention of HAp crystallization with Mg ions. Highly crystallized HAp coatings were successfully formed on pure magnesium and AZ series alloys. Corrosion behavior of HAp-coated pure magnesium was examined by cyclic dry and wet tests with 1 g m⁻² NaCl on the surface and polarization tests in a 3.5 wt% NaCl solution. A HAp-coated pure magnesium showed no noticeable corrosion pits after the dry and wet test. HAp-coated specimens showed 10³-10⁴ times lower anodic current density than as-polished specimen in the polarization test. The results demonstrate the remarkable anticorrosion performance of HAp coatings on magnesium for the first time.     

Enhanced energy storage performance and temperature stability achieved by a synergic effect in Nd3+/Ga3+ co-doped (Na0.5Bi0.5)TiO3 -based ceramics

(1-x)(0.75(Na_0.5Bi_0.5)TiO₃-0.25SrTiO₃)-xNdGaO₃ ceramics (NBST-xNG, x = 0–0.06) were fabricated through a solid-state reaction method. High-valent Nd³⁺ ions enter the perovskite A-site to occupy Bi vacancies resulting from the volatilization of Bi, inhibiting the formation of oxygen vacancies and contributing to an enhanced breakdown electric field (E_b). Low-valent Ga³⁺ ions enter the B-site to substitute for Ti⁴⁺ ions, resulting in the formation of random electric fields (REFs) at the B-site due to co-occupying hetero-valence ions of Ga³⁺/Ti⁴⁺, which significantly reduces ferroelectric hysteresis. Therefore, a synergic effect of A- and B-sites co-doping was realized in NBST-xNG ceramics. Benefitting from this synergic effect, an enhanced recoverable energy storage density (W_rec) of 2.88 J/cm³ and an efficiency (η) of 83% are simultaneously obtained in NBST-0.04NG ceramics under a moderate electric field (E) of 200 kV/cm. Compared with most NBT-based ceramics, the values of (η vs W_rec/E²) for NBST-0.04NG ceramics show an obvious advantage, indicating excellent potential for application as an energy storage material. Moreover, W_rec and η of NBST-0.04NG ceramics exhibit excellent temperature stability from 30 °C to 200 °C due to the enhanced correlation strength of polar nanoregions (PNRs) and local structural stability. This work provides a potential strategy to improve the energy storage performance of NBT-based ceramics via the synergic effect of A- and B-site co-doping.     

A multifunctional strontium/silver-co-substituted hydroxyapatite derived from biogenic source as antibacterial biomaterial

The bioactive properties of hydroxyapatite (HAp) facilitate bone regeneration, however, its physico-chemical and bioactive properties can be further enhanced by ionic substitutions within the crystalline lattice. In this work, substitution with Sr²⁺ and Ag⁺ ions was investigated for the improvement of osseointegration and antibacterial activity in potential treatment of traumatic bone injuries. A series of single substituted HAp with Sr²⁺ or Ag⁺ ions and Ag/Sr-co-substituted HAp with different degrees of substitution (0, 1, 2.5, and 5 mol%) were obtained by wet precipitation from cuttlefish bone. Rietveld refinement indicated successful Ca²⁺ substitution by increasing cell parameters due to the larger ionic radii of Sr²⁺ and Ag⁺ compared to Ca²⁺, which was confirmed by elemental mapping showing uniform distribution of substituent cations. Characterization of the zeta-potential of Ag/Sr-co-substituted HAp showed negatively charged populations, at potentials not lower than ?15 mV. Increasing the degree of substitution resulted in decreasing zeta-potential. The higher absorption capacity of bovine serum albumin was determined on Ag/Sr-co-substituted HAp powders as compared to non-substituted HAp. All Ag-substituted HAps have shown an antibacterial activity towards Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli, as determined by inhibition zone, viability analysis and scanning electron microscopy. In addition, non-cytotoxicity towards human cells was confirmed by in vitro tests with embryonic kidney 293 and mesenchymal stem cells.     

Luminescence and electrical properties of Eu-modified Bi0.5Na0.5TiO3 multifunctional ceramics

The Eu³⁺-modified Bi_0.5Na_0.5TiO₃ (BNT) ceramics have been fabricated by the solid-state reaction method. The impact of Eu³⁺ doping on the structure, photoluminescence, and electrical properties has been studied by XRD, SEM, PL spectra, and LCR meter. X-ray diffraction analysis reveals that the crystal structure of the samples is well matched with the trigonal perovskite, and the optimal temperature of presintering is 880°C. The Eu³⁺-doped BNT ceramics show excellent red fluorescence at 614 nm corresponding to the ⁵D₀→⁷F₂ transition of Eu³⁺ under 466 nm excitation and relatively long fluorescence lifetime. The BNT-0.02Eu ceramic density is up to 5.68 g/cm³ and the relative density is up to 94.6% with sintering temperature 1075°C. The piezoelectric constant (d₃₃) of samples has been significantly improved up to 110 pC/N by Eu³⁺ doping. The BNT-0.03Eu ceramic presintered at 880°C and sintered at 1050°C has good dielectric properties and excellent luminescence properties. Eu³⁺-doped BNT ceramics make it potential applications for novel integrated electro-optical and multifunctional devices.     

Effect of Mn doping on hydrolysis of low-temperature synthesized metastable alpha-tricalcium phosphate

In the present work, effect of Mn doping on hydrolysis rate of low-temperature synthesized metastable α-tricalcium phosphate (α-TCP) was investigated. α-TCP powders containing different amount of Mn²⁺ ions (0, 0.5 and 1 mol%) were synthesized by wet co-precipitation process, followed by annealing and crystallization of as-precipitated amorphous calcium phosphate at 700 °C. It was demonstrated that the presence of Mn²⁺ ions significantly retards hydrolysis rate of α-TCP. While pristine α-TCP fully hydrolyzed with a conversion to calcium-deficient hydroxyapatite in 10 h, complete hydrolysis of α-TCP doped with 0.5 and 1 mol% of Mn occurred only after 20 and 35 h, respectively. Initial and final products were characterized by X-ray diffraction (XRD) analysis, infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). Chemical composition of starting and fully hydrolyzed α-TCP powders was determined by inductively coupled plasma optical emission spectrometry (ICP-OES).     

Synthesis,Crystal Structure,and Luminescence Properties of Y4Si2O7N2: Eu2+ Oxynitride Phosphors

Y₄Si₂O₇N₂: Eu²⁺ phosphor has been prepared by a pretreatment method. Reduction in Eu³⁺ ions into Eu²⁺ by the use of hydrogen iodide (HI) is verified by X‐ray absorption near‐edge structure (XANES) and electrode potential analysis. Y₄Si₂O₇N₂: Eu²⁺ phosphor has a broad emission band in the range of 400–500 nm. Furthermore, the effect of Zr doping on the structure and luminescence properties of Y₄Si₂O₇N₂: Eu²⁺ phosphor is researched. It found that the Zr doping leads to an emission blueshift, and improves the luminescence intensity and thermal quenching behavior of Y₄Si₂O₇N₂: Eu²⁺ phosphors. Prospectively, the pretreatment approach could be extended to develop other Eu²⁺‐doped compounds.     

Lightweight porous silica-alumina ceramics with ultra-low thermal conductivity

Thermal protection has always been an important issue in the energy, environment and aerospace fields. Porous ceramics produced by the particle-stabilized foaming method have become a competitive material for thermal protection because of their low density and low thermal conductivity. However, the study of porous ceramics for composite systems using particle-stabilized foaming method was relatively rare. Here, silica-alumina composite porous ceramics were prepared by particle-stabilized foaming method, which was achieved by tailoring the surface charges of silica and alumina through adjustment of the pH. Porous ceramics exhibited porosity as high as 97.49% and thermal conductivity (25 °C) as low as 0.063 W m^?1 K^?1. The compressive strength of porous ceramics sintered at 1500 °C with a solid content of 30 wt% could reach 0.765 MPa. Based on the light weight and excellent thermal insulation properties, the composite porous ceramic could be used as a potential thermal insulation material in the spacecraft industry.