Natural rubber/ethylene propylene diene blends for high insulation iron crossarms

This research studied the composition and behavior of natural rubber (NR) and ethylene propylene diene monomer (EPDM) blends at various carbon black concentrations (0–30 phr) in terms of electrical resistivity, dielectric breakdown voltage testing, and physical properties. The blends having electrical properties suitable for application in high‐insulation iron crossarms were selected for investigation of compatibility and increased physical properties. The effect of the homogenizing agent concentration on improvement of compatibility of blends was studied by scanning electron microscopy, pulsed nuclear magnetic resonance spectroscopy, and rheology techniques. We also examined mechanical properties such as tensile strength, tear strength, elongation at break, and hardness. The NR/EPDM blends filled with a fixed concentration of silica were investigated for ozone resistance. A carbon black content as high as 10 phr is still suitable for the insulation coating material, which can withstand electrical voltage at 10 kVac. Addition of the homogenizing agent at 5 phr can improve the mechanical compatibility of blends, as evidenced by the positive deviation of shear viscosity of the rubber blend, that is, the calculated shear viscosity being higher than that of experimental data. Moreover, the pulsed NMR results indicated that the spin‐spin relaxation (T₂) of all three components of the rubber blend was compressed upon the addition of the homogenizing agent. The ratio of NR/EPDM in the blend to best resist the ozone gas is 80/20 with the addition of silica of 30 phr into the blend. Also, the NR/EPDM filled with silica had a decreased change in thermal and mechanical properties of blends after thermal aging. The synergistic effect of silica content and high NR content (80) in 20 phr EPDM could improve antioxidation by ozone in the absence of a normal antioxidant for natural rubber. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3401–3416, 2004     

Formulation and morphology of kaolin-filled rubber composites

In the present work the formulation and morphology of novel kaolin-filled rubber composites were investigated. The kaolin-filled rubber composites were obtained by filling rubbers such as natural rubber (NR), styrene–butadiene rubber (SBR), polybutadiene rubber (ER), nitrile butadiene rubber (NBR), ethylene propylene diene monomer (EPDM), chloroprene rubber (CR) and methyl vinyl silicon rubber (MVQ). The best formulation of filled rubbers was determined by determining the mechanical and thermal properties of the composites. Structural characterization was carried out by using infrared spectroscopy (IR) and a polarizing light microscope (PLM). The kaolin/rubber composites have outstanding mechanical and thermal properties except elongation at break, and good compatibility. The best formulation of kaolin filled rubbers is respectively 40 parts per hundred rubber (phr), 40 phr, 50 phr, 40 phr, 50 phr, and 50 phr for NR, SBR, BR, NBR, EPDM and CR. Kaolin can replace silica in the specific rubber products, and is suitable to reinforce more steric rigid rubber.     

Poly(styrene)‐ and Poly(styrene‐co‐methyl methacrylate)‐graft‐hydrogenated natural rubber latex: Aspect on synthesis,properties, and compatibility

The undesirable properties of natural rubber (NR) can be improved via hydrogenation and graft copolymerization. Hydrogenated NR (HNR) latex was prepared via diimide reduction and then grafted with styrene (ST) or ST/methyl methacrylate (MMA) to form poly(ST)‐graft‐HNR (poly(ST)‐g‐HNR, GHNRS) or poly(ST‐co‐MMA)‐g‐HNR (GHNRSM), respectively. For the grafting of ST monomer onto HNR particles, the %monomer conversion and %grafting efficiency (%GE) were monitored as functions of %hydrogenation, monomer and initiator concentrations, temperature, and time. Under the optimum condition (HNR with 54.3% hydrogenation; 100 phr of ST, 1 phr of initiator at 50°C for 8 h), maximum %conversion and %GE of 44.6% and 36.9%, respectively, were achieved. Thermogravimetric analysis revealed that the HNR grafted with ST or ST/MMA had higher decomposition temperature than an ungrafted one. When these graft products were blended at 10% (w/w) with acrylonitrile‐butadiene‐styrene (ABS) resin, the GHNRS/ABS and GHNRSM/ABS composites exhibited the higher flexural strength and heat aging tolerance compared to the ungrafted HNR/ABS composite. Scanning electron microscopy (SEM) also showed the higher degree of homogeneity at the fractural surface, supporting the higher compatibility between the ABS and the GHNRS or GHNRSM phases in the blends. J. VINYL ADDIT. TECHNOL., 22:100–109, 2016. © 2014 Society of Plastics Engineers     

Effect of silanized silica nanofiller on tack and green strength of selected filled rubbers

BACKGROUND: Tack and green strength of filled and gum (unfilled) natural rubber (NR), poly(styrene‐co‐butadiene) rubber (SBR), polybutadiene rubber (BR) and (SBR‐BR) blend with different loadings of reinforcement agent, silanized silica nanofiller (Coupsil 8113), were studied and the results compared and discussed. RESULTS: It was found that silica was fully dispersed in rubber matrix after 13 min of mixing. In addition, with some exceptions for NR and (SBR‐BR) blend, filler loading decreased the tack strength of the studied filled rubbers. Green strength and Mooney viscosity increased with filler loading for all studied filled rubbers but with different rates and amounts. The optimum filler loadings for NR and (SBR‐BR) filled blend were 30 and 10 phr, respectively. Tacks of NR filled rubbers were much higher than those of synthetic filled rubbers. CONCLUSION: It was concluded that filler loading alters substantially the tack and green strength of the rubbers under investigation. Copyright © 2009 Society of Chemical Industry     

Short fibers as reinforcement of rubber compounds

The effect of aramid, glass and cellulose short fibers on the processing behavior, crosslinking density and mechanical properties of natural rubber (NR), ethylene‐propylene‐diene terpolymer rubber (EPDM) and styrene‐butadiene rubber (SBR) has been investigated. Two fiber percentages (10 and 20 phr) were added to the rubber. The results have shown that the above‐mentioned fibers, especially aramid fibers, are effective reinforcing agents for these rubbers, giving rise to a significant increase in mechanical properties, such as tensile modulus and strength, and tear and abrasion resistance. Moreover, a significant decrease in the time to reach 97% of curing, t′_c (97) is observed, which indicates that the fibers tend to increase the vulcanization rate, regardless of the rubber used. Fibers give also rise to an increase in crosslinking, especially the aramid fibers.     

Effects of EPDM‐g‐MAH compatibilizer and internal mixer processing parameters on the properties of NR/EPDM blends: An analysis using response surface methodology

This study evaluates the effects of ethylene‐propylene‐diene‐monomer grafted maleic anhydride (EPDM‐g‐MAH) and internal mixer melt compounding processing parameters on the properties of natural rubber/ethylene‐propylene‐diene rubber (NR/EPDM) blends. Using Response Surface Methodology (RSM) of 2⁵ two‐level fractional factorial, we studied the effects of NR/EPDM ratio, mixing temperature, Banbury rotor speed, mixing period, and EPDM‐g‐MAH contents in NR/EPDM blends. The study found that the presence of EPDM‐g‐MAH in NR/EPDM blends had a predominant role as a compatibilizing agent, which affected the processability and properties of the final material. We also determined the model fitting with constant determination, R² of 99.60% for tensile strength (TS) response with a suggested combination of mixing process input parameters. The reproducibility of the proposed mixing strategy was then confirmed through model validation with a minor deviation at +2.303% and higher desirability of 0.960. This study is essential in providing a process design reference for NR/EPDM blends preparation by melt‐blending and the role of a compatibilizer from the systematic Design of Experiment (DOE) approach. The experimental findings were further supported with swelling and cross‐link density measurements, differential scanning calorimetry analysis, and observation of fracture morphology using a scanning electron microscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42199.     

Sol‐gel process of alkyltriethoxysilane in latex for alkylated silica formation in natural rubber

Sol‐gel process of alkyltriethoxysilanes that was dispersed in natural rubber latex was used to generate alkylated silica particles inside the rubber matrix. Three types of alkyltriethoxysilanes were chosen, i.e., vinyltriethoxysilane (VTOS), ethyltriethoxysilane (ETOS), and i‐butyltriethoxysilane (BTOS), as they differed in the type of one substituent group. Together with tetraethoxysilane (TEOS), a typical precursor for silica formation, all silanes were studied for their conversion to silica and subsequent reinforcement capabilities in sulfur‐vulcanized rubber. The in situ generated silicas were fine and well dispersed in the rubber matrix, as analyzed by SEM and TEM. Solid‐state ²⁹Si‐NMR technique was used to confirm the presence of alkyl substituents on the silica particles buried inside the rubber matrix. Tensile and tear properties of the in situ silica‐filled NR vulcanizates were higher than those of the vulcanizate prepared by conventional mixed method. Among the three alkyltriethoxysilanes used, only VTOS, when used as a mixture with TEOS, did not cause a reduction in silica formation. The resulting vinylated silica tended to enhance the tensile modulus and resistant to tear of the rubber vulcanizates. Cure characteristic and swelling behavior in toluene of the silica‐containing vulcanizates were also investigated. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of NR/EPDM blends using response surface methodology

The effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of natural rubber/ethylene–propylene–diene rubber (NR/EPDM; 70 : 30 phr) blends were studied. The compounds were prepared by melt compounding method. Using response surface methodology of two‐level full factorial, the effects of ENR‐50 contents (?1 : 5 phr; +1 : 10 phr), mixing temperature (?1 : 50°C; +1 : 110°C), rotor speed (?1 : 40 rpm; +1 : 80 rpm), and mixing time (?1 : 5 min; +1 : 9 min) in NR/EPDM blends were evaluated. Cure characteristics and tensile properties were selected as the responses. The significance of factors and its interaction was analyzed using ANOVA and the model's ability to represent the system was confirmed using the constant of determination, R² with values above 0.90. It was found that the presence of ENR‐50 has the predominant role on the properties of NR/EPDM blends. The addition of ENR‐50 significantly improved cure characteristics and tensile strength up to 5.12% and 6.48% compared to neat NR/EPDM blends, respectively. These findings were further supported by swell measurement, differential scanning calorimetry, and scanning electron microscopy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40713.     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Optimization of accelerators on curing characteristics,tensile, and dynamic mechanical properties of (natural rubber)/(recycled ethylene‐propylene‐diene‐monomer) blends

The migration of sulfur from natural rubber (NR) compound to the ground waste ethylene‐propylene‐diene monomer (EPDM) rubber phase may have caused the cure incompatibility between these two rubbers. Optimization of accelerators had been adopted to overcome the cure incompatibility in NR/(R‐EPDM) blends as well as to get increased curative distribution. In this study, blends of NR and R‐EPDM were prepared. The effect of accelerator type on curing characteristics, tensile properties, and dynamic mechanical properties of 70/30/NR/(R‐EPDM) blend was investigated. Four types of commercial accelerators were selected [ie, N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , N‐cyclohexyl‐benzothiazyl‐sulfenamide (CBS), tetramethylthiuram disulfide, and 2‐mercaptobenzothiazol]. It was found that the tensile strength of the blends cured in the presence of CBS was relatively higher than the other three accelerators. Scanning electron micrographs of CBS‐cured NR/(R‐EPDM) blends exhibited more roughness and cracking path, indicating that higher energy was required toward the fractured surface. The high crosslinking density observed from the swelling method could be verified from the storage modulus (E′) and damping factor (tan δ) where (tetramethylthiuram disulfide)‐cured NR/(R‐EPDM) blends provided a predominant degree of crosslinking followed by N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , CBS, and 2‐mercaptobenzothiazol, respectively. J. VINYL ADDIT. TECHNOL., 21:79–88, 2015. © 2014 Society of Plastics Engineers     

The partial replacement of silica or calcium carbonate by halloysite nanotubes as fillers in ethylene propylene diene monomer composites

The effect of partial replacement of silica or calcium carbonate (CaCO₃) by halloysite nanotubes (HNTs) on the curing behavior, tensile properties, dynamic mechanical properties, and morphological characteristics of ethylene propylene diene monomer (EPDM) composites was studied. Five different compositions of EPDM/Silica/HNT and EPDM/CaCO₃/HNT compounds (i.e. 100/30/0, 100/25/5, 100/15/15, 100/5/25, and 100/0/30 parts per hundred rubber (phr)) were prepared on a two‐roll mill. The results indicated that the replacement of CaCO₃ by HNTs increased the tensile strength, elongation at break (E_b), and tensile modulus of composites from 0 to 30 phr of HNTs whereas for silica, the maximum tensile strength and E_b occurred at 5 phr loading of HNTs with an enhanced stress at 300% elongation (M300). The curing results show that, with replacement of silica or CaCO₃ by HNTs, the cure time (t₉₀) and cure rate (CRI) were decreased and increased, respectively. Scanning electron microscopy investigation confirmed that co‐incorporation of 5 phr of HNTs with silica would improve the dispersion of silica and enhanced the interactions between fillers and EPDM matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Silica‐modified SBR/BR blends

The purpose of this article is that the silica‐modified SBR/BR blend replaces natural rubber (NR) in some application fields. The styrene‐butadiene rubber (SBR) and cis‐butadiene rubber (BR) blend was modified, in which silica filler was treated with the r‐Aminopropyltriethoxysilane (KH‐550) as a coupling agent, to improve mechanical and thermal properties, and compatibilities. The optimum formula and cure condition were determined by testing the properties of SBR/BR blend. The properties of NR and the silica‐modified SBR/BR blend were compared. The results show that the optimum formulawas 80/20 SBR/BR, 2.5 phr dicumyl peroxide (DCP), 45 phr silica and 2.5 mL KH‐550. The best cure condition was at 150°C for 25 min under 10 MPa. The mechanical and thermal properties of SBR/BR blend were obviously modified, in which the silica filler treated with KH‐550. The compatibility of SBR/BR blend with DCP was better than those with benzoyl peroxide (BPO) and DCP/BPO. The crosslinking bonds between modified silica and rubbers were proved by Fourier transform infrared analysis, and the compatibility of SBR and BR was proved by polarized light microscopy (PLM) analysis. The silica‐modified SBR/BR blend can substitute for NR in the specific application fields. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

新型白炭黑改性橡胶研究

采用2种新型白炭黑替代常用白炭黑来改性天然橡胶（NR）、顺丁橡胶（BR）、丁笨橡胶（SBR）、三元乙丙橡胶（EPDM）、丙烯酸酯橡胶（ACM）和硅橡胶。研究不同用量和不同种类的白炭黑对上述几种橡胶进行改性,通过对硬度、扯断伸长率、拉伸强度、磨耗和耐老化性能的测试,确定白炭黑的最佳用量和最适宜的种类。结果表明：白炭黑填料用量为80份时效果最好,普通白炭黑适合做EPDM的补强剂,碱法白炭黑对NR、SBR和ACM的改性效果更好,而酸法白炭黑改性的橡胶拉伸强度和硬度很小,不适于补强;白炭黑对硅橡胶的改性效果不好,得到的产品硬度很小,无法进行力学性能测试。     

Effects of fillers,maleated ethylene propylene diene diene rubber,and maleated ethylene octene copolymer on phase morphology and oil resistance in natural rubber/nitrile rubber blends

The phase morphology and oil resistance of 20/80 NR/NBR blends filled with different types of fillers and copolymers were investigated. In the case of filler effect, N220, N330, and N660 carbon blacks with different particle sizes were used. Additionally, the blends filled with nonblack‐reinforcing fillers, that is, precipitated and silane‐treated silica, were investigated. To study the compatibilization effect, maleated ethylene propylene diene rubber (EPDM‐g‐MA) and maleated ethylene octene copolymer (EOR‐g‐MA) were added to the blends. The results revealed that the addition of filler, either carbon black or silica, to the blend caused a drastic decrease in NR dispersed phase size. Carbon blacks with different particle sizes did not produce any significant difference in NR dispersed phase size under the optical microscope. Silica‐filled blends showed lower resistance to oil than did the carbon black–filled blends. In addition, it was determined that neither EOR‐g‐MA nor EPDM‐g‐MA could act as a compatibilizer for the blend system studied. The oil resistance of the blends with EPDM‐g‐MA is strongly affected by the overall polarity of the blend. In the case of EOR‐g‐MA, the oil resistance of the blends is significantly governed by both overall polarity of the blend and phase morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1156–1162, 2003     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Design and properties of a series of high‐temperature thermoplastic elastomeric blends from polyamides and functionalized rubbers

A series of high‐temperature thermoplastic elastomers (TPEs) and thermoplastic vulcanisates (TPVs) were successfully developed based on two different types of heat resistant polyamide (PA) (25 parts by weight)—PA‐12 and PA‐6, in combination with three different functionalized rubbers (75 parts by weight) of varying polarity, e.g., maleic anhydride grafted ethylene propylene diene terpolymer (MA‐g‐EPDM), sulphonated ethylene propylene diene terpolymer, and carboxylated acrylonitrile butadiene rubber, by melt mixing method. These rubbers have low level of unsaturation in its backbone, and the plastics showed high melting range. Thus, the developed TPEs and TPVs were expected to be high temperature resistant. Resol type resin was used for dynamic vulcanization to further increase the high temperature properties of these blends. Interestingly, initial degradation temperature of the prepared blends was much higher (421 °C for MA‐g‐EPDM/PA‐12) than the other reported conventional TPEs and TPVs. Fourier transform infrared analysis described the interactive nature of the TPEs and TPVs, which is responsible for their superior properties. The maximum tensile strength with lowest tension set was observed for the carboxylated acrylonitrile butadiene rubber/PA‐12 TPV. Mild increase in mechanical properties without any degradation was observed after recycling. Dynamic mechanical analysis results showed two distinct glass transition temperatures and indicated the biphasic morphology of the blends, as evident from the scanning electron microscopy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45353.     

A comparison of the properties of rice husk ash,silica, and calcium carbonate filled 75 : 25 NR/EPDM blends

The effects of incorporation of three different fillers, i.e., rice husk ash (RHA), silica, and calcium carbonate (CaCO₃), over a loading range of 0–60 phr on the curing characteristics, processability, mechanical properties, and morphology of 75 : 25 natural rubber (NR)/ethylene‐propylene‐diene monomer (EPDM) blends were studied using a conventional vulcanization system. Filler loading and type influence the processability of the blends in which RHA and CaCO₃ offer better processing advantage over silica. The best improvement in the tensile and tear strength and abrasion resistance of the 75 : 25 NR/EPDM blends with additional fillers was achieved when filled with silica. However, RHA and CaCO₃ were better in resilience property compared to that of silica. The RHA filled blends showed higher failure properties and abrasion resistance but lower ozone resistance than that containing CaCO₃. Scanning electron micrographs revealed that the morphology of the blend filled with silica is finer and more homogenous compared to the blend filled with RHA and CaCO₃. According to these observations, RHA can be used as a cheaper filler to replace CaCO₃ in rubber blends where improved mechanical properties are not so critical. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

New approach for preparation of dry natural rubber nanocomposites through acid‐free co‐coagulation: Effect of organoclay content

Natural rubber (NR) vulcanizates exhibit good mechanical properties compared to vulcanizates of synthetic rubbers. Incorporation of a conventional filler at higher loadings to NR enhances its modulus, while reduction in tensile strength and elongation. This paper presents a new strategy for development of a NR‐clay nanocomposite with enhanced mechanical properties by incorporation of lower loadings (2–8 phr) of cetyl trimethyl ammonium bromide modified montmorillonite clay (OMMT‐C) under acid‐free environment. The effect of OMMT‐C loading on cure characteristics, rubber‐filler interactions, crosslink density, dynamic mechanical thermal properties, and mechanical properties were evaluated. Incorporation of OMMT‐C accelerated the vulcanization process and enhanced mechanical properties. X‐ray diffraction analysis and scanning electron microscopy images revealed that the formation of intercalated clay structures at lower OMMT‐C loadings, and clay aggregates at higher loadings. A nanocomposite at OMMT‐C loading of 2 phr exhibited the best balanced mechanical properties, and was associated with highest crosslink density and rubber–filler interactions. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46502.     

Effect of adhesive‐coated glass fiber in natural rubber (NR), acrylonitrile rubber (NBR), and ethylene–propylene–diene rubber (EPDM) formulations. II. Effect of cyclic loading,abrasion, and accelerated aging

Treated glass fibers (RICS, 3 and 6 mm in length) were added at a concentrations of 10, 20, and 30 phr in natural rubber (NR), nitrile rubber (NBR), and ethylene–propylene–diene comonomer (EPDM) formulations, in both plain and carbon black mixes. The compounds were mixed in two‐roll mill and were evaluated for their resistance to hot‐air aging, abrasion, compression set, Goodrich heat buildup, De Mattia fatigue, and for NR mixes, adhesion in the tensile mode. The vulcanizates of the three rubbers showed resistance to hot‐air aging. Abrasion resistance was poor for NR, and it improved with carbon black addition in the presence of treated glass fiber in NBR. In carbon‐black‐added EPDM vulcanizates, the abrasion resistance and fatigue resistance were better. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1124–1135, 2004     

Application of lime kiln dust as a filler in the natural rubber industry

Lime kiln dust (LKD) obtained from kraft chemical recovery systems by conversion of calcium carbonate (CaCO₃) back into calcium oxide (CaO) for reuse in the causticizing process, is mainly composed of CaCO₃. A two‐stage conventional mixing procedure was used to incorporate LKD into natural rubber (NR). For comparison purposes, four commercial fillers, stearic acid coated CaCO₃, ground CaCO₃, silica, and carbon black, were also used. The effect of these fillers on the curing characteristics and mechanical properties of NR materials at various loadings ranging from 0 to 60 phr were studied. The results indicate that the use of LKD filler resulted in a lower Mooney viscosity and shorter curing time in the NR materials. The incorporation of LKD into NR improved the Young's modulus and hardness but decreased the tensile strength and tear strength. However, LKD was better in processability than the commercial fillers. Scanning electron micrographs revealed that the morphology of the rubbers filled with reinforcing fillers, such as silica and carbon black, was finer and more homogeneous compared to the those of the rubbers filled with LKD and commercial CaCO₃. The dispersion of LKD and commercial CaCO₃ fillers in the rubber matrix was discontinuous, which in turn, generated a weak structure compared with the reinforcing fillers. According to these observations, LKD could be used as a cheaper filler for NR materials where improved mechanical properties are not critical. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011