Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) reinforced by poly(lactic acid) fibers

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) (PBSA) reinforced by poly(lactic acid) (PLA) fibers were developed by hot compression and characterized by Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analyzer, and tensile testing. The results show that PBSA and PLA are immiscible, but their interface can be improved by processing conditions. In particular, their interface and the resulting mechanical properties strongly depend on processing temperature. When the temperature is below 120 °C, the bound between PBSA and PLA fiber is weak, which results in lower tensile modulus and strength. When the processing temperature is higher (greater than 160 °C), the relaxation of polymer chain destroyed the molecular orientation microstructure of the PLA fiber, which results in weakening mechanical properties of the fiber then weakening reinforcement function. Both tensile modulus and strength of the composites increased significantly, in particular for the materials reinforced by long fiber. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43530.     

Thermal,mechanical, and rheological properties of polylactide/poly(1,2‐propylene glycol adipate)

Polylactide (PLA) was melt blended with poly(1,2‐propylene glycol adipate) (PPA) in a Thermo‐Haake mixer. Thermal, mechanical, and rheological properties of the blends were investigated by means of differential scanning calorimetry, dynamic mechanical analysis, tensile test, and small amplitude oscillatory shear rheometry. PPA lowered the glass transition temperature and increased the ability of PLA to cold crystallization. With the increase in PPA content (5–25 wt%), the blends showed decreased tensile strength and Young's modulus; however, impact strength and elongation‐at‐break along were dramatically increased due to the plastic deformation. Morphological results of PLA/PPA blends showed that PPA was good compatible with PLA. The plasticization effect of PPA was also manifested by the lowering of dynamic storage modulus and viscosity in the melt state of the blends compared with neat PLA. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Toughening of poly(lactic acid) with the renewable bioplastic poly(trimethylene malonate)

The aim of this work was to enhance poly(lactic acid)'s (PLA) flexibility and ductility by blending it with another bioplastic. Poly(trimethylene malonate) (PTM), developed as part of this study, was synthesized from 1,3‐propane diol and malonic acid via melt polycondensation. Blend films of PLA and PTM were prepared by solvent casting from chloroform. Differential scanning calorimetry and thermogravimetric analysis were used to show shifted phase transitions and a single glass‐transition temperature, indicating miscibility of PTM in the blend films. Morphology and mechanical characterizations of the PLA/PTM blend films were performed by atomic force microscopy using a quantitative nanomechanical property mapping mode, tensile testing, and scanning electron microscopy. Miscible blends exhibited Young's modulus and elongation at break values that can significantly extend the usefulness of PLA in commercial applications. The blending of PTM with PLA resulted in films with a 27‐fold increase in toughness compared with neat PLA film. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40888.     

Improved processability and performance of biomedical devices with poly(lactic acid)/poly(ethylene glycol) blends

To improve the processability of micropolymer‐based devices used for biomedical applications, poly(lactic acid) (PLA) was melt‐blended with poly(ethylene glycol)s (PEGs) of different molecular weights (MWs; weight‐average MWs = 200, 800, 2000, and 4000; these PEGS are referred to as PEG200, PEG800, PEG2000, and PEG4000, respectively, in this article). The thermal properties, mechanical properties, and rheological properties of the PLA and the PLA–PEG blends were investigated. The tensile samples’ morphologies showed that the low‐MW PEGs filled molds well. The rheological properties confirmed that the low‐MW PEGs decreased the complex viscosity, and improved the processability. With decreasing PEG MW, the PLA glass‐transition temperature decreased. The nanoindenter data show that the addition of PEG decreased the modulus and hardness of PLA. The morphologies of the tensile samples showed that with increasing PEG MW, the thicknesses of the core layers increased gradually. The elongation at break was improved by approximately 247% with the addition of PEG200. Such methods can produce easily processed biological materials for producing biomedical products. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45194.     

Synthesis of poly(butyl acrylate)—laponite nanocomposite nanoparticles for improving the impact strength of poly(lactic acid)

This work aims at preparing and characterizing poly(butyl acrylate) (PBA)—laponite (LRD) nanocomposite nanoparticles and nanocomposite core (PBA‐LRD)‐shell poly(methyl methacrylate) (PMMA) nanoparticles, on the one hand, and the morphology and properties of poly(lactic acid) (PLA)‐based blends containing PBA‐LRD nanocomposite nanoparticles or (PBA‐LRD)/PMMA core–shell nanoparticles as the dispersed phase, on the other hand. The PBA and (PBA‐LRD)/PMMA nanoparticles were synthesized by miniemulsion or emulsion polymerization using LRD platelets modified by 3‐methacryloxypropyltrimethoxysilane (MPTMS). The grafting of MPTMS onto the LRD surfaces was characterized qualitatively using FTIR and quantitatively using thermogravimetric analysis (TGA). The amounts of LRD in the PBA‐LRD nanocomposites were characterized by TGA. The PBA/PMMA core–shell particles were analyzed by ¹H‐NMR. Their morphology was confirmed by SEM and TEM. Mechanical properties of (PBA‐LRD)/PLA blends and (PBA‐LRD)/PMMA/PLA ones were tested and compared with those of the pure PLA, showing that core–shell particles allowed increasing impact strength of the PLA while minimizing loss in Young modulus and tensile strength. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Properties of soy protein isolate/poly(ethylene‐co‐ethyl acrylate‐co‐maleic anhydride) blends

Blends of soy protein isolate (SPI) with 10, 20, 30, 40, and 50% poly(ethylene‐co‐ethyl acrylate‐co‐maleic anhydride) (PEEAMA), with or without addition of 2.0 wt % methylene diphenyl diisocyanate (MDI), were prepared by mixing with an intensive mixer at 150°C for 5 min, and then milling through a 1‐mm sieve. Blends were then compression‐molded into a tensile bar at 140°C. Thermal and mechanical properties and water absorption of the blends were studied by differential scanning calorimetry (DSC), dynamical mechanic analysis (DMA), a test of modulus and tensile strength (with an Instron tensile tester), a water absorption test, and scanning electron microscopy (SEM). The blends showed two composition‐dependent glass transition temperatures. Furthermore, as the SPI content increased, the melting temperature of PEEAMA remained constant but the heat of fusion decreased. These results indicate that SPI and PEEAMA were partially miscible. Morphology observations support these results. Increasing the PEEAMA content resulted in decreases in the modulus and tensile strengths and increases in the elongation and toughness of the blends. Water absorption of the blends also decreased with increased PEEAMA content. Incorporating MDI further decreased the water absorption of the blends. The mechanism of water sorption of SPI was relaxation controlled, and that of the blends was diffusion controlled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 407–413, 2003     

The effect of composition on the dynamic and mechanical properties of natural rubber–poly(methylmethacrylate) blends

The miscibility of the components in natural rubber–poly(methylmethacrylate) blends for potential use as reinforced rubbers was evaluated using the glass transition temperatures, peak widths of the loss tangent peak at the glass transition and the complex heat capacity data obtained from dynamic mechanical thermal analysis (DMTA), and modulated differential scanning calorimetry (MDSC). In addition, the effect of the poly(methylmethacrylate) content on the dynamic mechanical and the physical properties such as tensile behavior and hysteresis loss was studied. DMTA and MDSC data clearly indicated that the blends were phase‐separated. Nevertheless, the glass transition temperature of the natural rubber component in the 30–50 wt % NR/PMMA blends has shifted to higher temperatures compared to the natural rubber treated under the same condition, indicating some limited extent of mixing of components in these blends. The physicomechanical properties including moduli at 100, 300, and 500% and tensile strength of the NR/PMMA blends were determined. Incorporation of PMMA into NR matrix improved the strength properties of the NR/PMMA blends prepared reasonably akin to interpenetrating polymer networks (IPN) polymerization method. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Hydrolytic stability of polylactide and poly(methyl methacrylate) blends

The hydrolytic stability of polylactide/poly(methyl methacrylate) (PLA/PMMA) blends prepared using a twin‐screw extrusion process was investigated. The effects of hydrolysis were monitored in neutral and alkaline media at 80 °C by tracking the changes in molecular weight distribution, weight loss, water uptake, and crystallization behavior. The crystallinity of PLA in blends prior to hydrolysis was shown to be largely hindered by the presence of PMMA. However, PLA recrystallized rapidly during hydrolysis. The PMMA in the blends was shown to provide increased hydrolytic and structural stability to the blends. In the neutral medium, the presence of PMMA delayed and reduced the weight loss but did not significantly affect PLA degradation kinetics. On the other hand, in the alkaline medium, the weight loss rate was strongly decreased in presence of PMMA and the kinetics of degradation was shown to be depend on PMMA content. The microstructure of these blends throughout the hydrolysis process was also examined by scanning electron microscopy. A porous structure, with interconnected pores in the 20–50 nm range, was developed due to the selective removal of PLA. Based on these morphological observations, erosion mechanism of PLA/PMMA blends was discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45991.     

Mechanical properties of poly(styrene‐co‐acrylonitrile)‐modified epoxy resin/glass fiber composites

Poly(styrene‐co‐acylonitrile) was used to modify diglycedyl ether of bisphenol‐A type epoxy resin cured with diamino diphenyl sulfone and the modified epoxy resin was used as the matrix for fiber‐reinforced composites (FRPs) to get improved mechanical properties. E‐glass fiber was used as fiber reinforcement. The tensile, flexural, and impact properties of the blends and composites were investigated. The blends exhibited considerable improvement in mechanical properties. The scanning electron micrographs of the fractured surfaces of the blends and tensile fractured surfaces of the composites were also analyzed. The micrographs showed the influence of morphology on the properties of blends. Results showed that the mechanical properties of glass FRPs increased gradually upon fiber loading. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

From microstructure to mechanical properties of compatibilized polylactide/thermoplastic starch blends

Bio‐degradable polymer blends of polylactic acid/thermoplastic starch (PLA/TPS) were prepared via direct melt blending varying order of mixing of ingredients fed into the extruder. The effect of interface interactions between PLA and TPS in the presence of maleic anhydride (MA) compatibilizer on the microstructure and mechanical properties was then investigated. The prepared PLA/TPS blends were characterized by scanning electron microscopy, differential scanning calorimetry (DSC), tensile, and rheological measurements. Morphology of PLA/TPS shows that the introduction of MA into the polymer matrix increases the presence of TPS at the interface region. DSC results revealed the reduction of glass transition temperature of PLA with contributions from both TPS and MA. The crystallization temperature was decreased by the addition of MA leading to reduction of overall crystallization of PLA/TPS blend. The mechanical measurements show that increasing MA content up to 2 wt % enhances the modulus of PLA/TPS more than 45% compared to the corresponding blends free of MA compatibilizer. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44734.     

Mechanical properties of natural fiber hybrid composites based on renewable thermoset resins derived from soybean oil,for use in technical applications

Natural fiber composites are known to have lower mechanical properties than glass or carbon fiber reinforced composites. The hybrid natural fiber composites prepared in this study have relatively good mechanical properties. Different combinations of woven and non‐woven flax fibers were used. The stacking sequence of the fibers was in different orientations, such as 0°, +45°, and 90°. The composites manufactured had good mechanical properties. A tensile strength of about 119 MPa and Young's modulus of about 14 GPa was achieved, with flexural strength and modulus of about 201 MPa and 24 GPa, respectively. For the purposes of comparison, composites were made with a combination of woven fabrics and glass fibers. One ply of a glass fiber mat was sandwiched in the mid‐plane and this increased the tensile strength considerably to 168 MPa. Dynamic mechanical analysis was performed in order to determine the storage and loss modulus and the glass transition temperature of the composites. Microstructural analysis was done with scanning electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) copolymer on the properties of polylactide/poly(methyl methacrylate) blend

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) P(S‐co‐GMA) copolymer on the properties of melt blended polylactide/poly(methyl methacrylate) (PLA/PMMA) 80/20 (wt %) composition was studied. In the literature high ductility levels were achieved by melt blending PLA with different additives. However, the gained ductility was counter balanced with drastic drops in strength and modulus values. The novelty of this work was the preparation of PLA‐based blends with polylactide content higher than 75 wt % which showed an impact resistance value improvement of about 60% compared with the neat PLA and maintained similar tensile strength and modulus values as well as glass transition temperature to neat PLA. The addition of only 3 pph of copolymer to PLA/PMMA blend improved the impact resistance almost 100%. The chemical reaction between PLA/PMMA blend and P(S‐co‐GMA) copolymer were analyzed by FTIR, rotational rheometry, and GPC/SEC. Phase structure and morphology were studied by Differential Scanning Calorimetry and Scanning Electronic Microscopy. Tensile and impact properties as well as thermal stability were also studied. Results showed that as the amount of copolymer in the blend was increased then higher was average molecular weight and polydispersity index. After the addition of P(S‐co‐GMA) copolymer to the PLA/PMMA blend the impact resistance, elongation at break and thermal stability were improved while tensile strength and elastic modulus remained almost unaltered. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43935.     

Mechanical properties of poly(lactic acid) and wheat starch blends with methylenediphenyl diisocyanate

Poly(lactic acid) (PLA) and wheat starch are biodegradable polymers derived from renewable sources. A previous study showed that thermally blending starch and PLA in the presence of methylenediphenyl diisocyanate (MDI) enhanced the mechanical properties of the blends. In this work, blends of PLA with various levels of wheat starch and MDI were hot mixed at 180°C then hot‐pressure molded at 175°C to form test specimens. The blends were characterized for mechanical properties, fracture microstructure, and water absorption. Pure PLA had a tensile strength of 62.7 MPa and elongation of 6.5%. The blend with 45% wheat starch and 0.5 wt % MDI gave the highest tensile strength of about 68 MPa with about 5.1% elongation. The blend with 20% starch and 0.5 wt % MDI had the lowest tensile strength of about 58 MPa with about 5.6% elongation. Dynamic mechanical analysis showed that storage modulus increased and tan δ decreased as starch level increased, but almost leveled off when starch level reached 45% or higher. Water absorption of the blends increased significantly with starch content. Yet the blend, if water proofed on its surface, has potential for short‐term disposable applications. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1257–1262, 2002; DOI 10.1002/app.10457     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part II: Mechanical and thermal properties

A novel process has been developed to manufacture poly(methyl methacrylate) (PMMA) pultruded parts. The mechanical and dynamic mechanical properties, environmental effects, postformability of pultruded composites and properties of various fiber (glass, carbon and Kevlar 49 aramid fiber) reinforced PMMA composites have been studied. Results show that the mechanical and thermal properties (i.e. tensile strength, flexural strength and modulus, impact strength and HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest impact strength and HDT, while carbon fiber/PMMA composites show the highest tensile strength, tensile and flexural modulus, and glass fiber/PMMA composites show the highest flexural strength. Experimental tensile strengths of all composites except carbon fiber/PMMA composites follow the rule of mixtures. The deviation of carbon fiber/PMMA composite is due to the fiber breakage during processing. Pultruded glass fiber reinforced PMMA composites exhibit good weather resistance. They can be postformed by thermoforming, and mechanical properties can be improved by postforming. The dynamic shear storage modulus (G′) of pultruded glass fiber reinforced PMMA composites increased with decreasing pulling rate, and G′ was higher than that of pultruded Nylon 6 and polyester composites.     

Compatibilization of poly(lactic acid)/high impact polystyrene interface using copolymer poly(stylene‐ran‐methyl acrylate)

In this work, a surfactant‐free emulsion polymerization method was utilized to synthesize poly(styrene‐ran‐methyl acrylate) (PSMA) at a styrene/(methyl acrylate) mole ratio of 75/25 with the aim to compatibilize high impact polystyrene (HIPS)/poly(lactic acid) (PLA) interface. HIPS/PLA blends with different PSMA contents were prepared. Their phase morphologies, mechanical properties, and rheological and crystallization behaviors were investigated using scanning electron microscopy, tensile tests, rotational rheometry, and differential scanning calorimetry. The rheological results showed that the complex viscosity, storage moduli, and loss moduli of PLA/HIPS blends were enhanced with increasing PSMA content. A decrease in the degree of crystallinity of PLA in PLA/HIPS blends with the addition of PSMA was observed in the differential scanning calorimetry results. It was also revealed that the addition of a small amount of PSMA can effectively improve the compatibility and thus the interfacial adhesion of the PLA/HIPS blends, thereby reducing the size of the HIPS dispersion phase. When 1 wt % of PSMA was used, compared with the PLA/HIPS blends without PSMA, the tensile strength and notched Charpy impact strength of PLA/HIPS blends were improved by 95.3% and 104.8%, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45799.     

Effects of annealing time and temperature on the crystallinity and heat resistance behavior of injection‐molded poly(lactic acid)

The effects of annealing time and temperature on the crystallinity of injection‐molded poly(lactic acid) (PLA) were investigated using differential scanning calorimetry and wide‐angle x‐ray diffraction. Differential scanning calorimetry, tensile test, and dynamic mechanical analysis showed that an increase in crystallinity in the PLA parts from the annealing treatment offers several benefits such as a higher glass transition temperature, better heat resistance, and greater storage modulus and tensile strength. Based on the experimental data, the degree of crystallinity, annealing time, and annealing temperature were found to closely follow the time–temperature superposition relationship. Namely, a master curve could be constructed based on either the Williams–Landel–Ferry equation or the Arrhenius relationship by shifting the crystallinity isotherms in the logarithmic scale horizontally along the log‐time axis. This relationship provides a quantitative guideline for annealing postinjection‐molded PLA parts to improve the heat resistance and mechanical properties. An increase of over 17% and 26% in tensile strength was achieved at an annealing temperature of 80°C for 30 min and 65°C for 31 h, respectively. POLYM. ENG. SCI. 2013. © 2012 Society of Plastics Engineers     

Crystallization,morphology, and mechanical behavior of polylactide/poly(ε‐caprolactone) blends

Optically pure polylactides, poly(L ‐lactide) (PLLA) and poly(D ‐lactide) (PDLA), were blended across the range of compositions with poly(ε‐caprolactone) (PCL) to study their crystallization, morphology, and mechanical behavior. Differential scanning calorimetry and dynamic mechanical analysis (DMA) of the PLA/PCL blends showed two T_gs at positions close to the pure components revealing phase separation. However, a shift in the tan δ peak position by DMA from 64 to 57°C suggests a partial solubility of PCL in the PLA‐rich phase. Scanning electron microscopy reveals phase separation and a transition in the phase morphology from spherical to interconnected domains as the equimolar blend approaches from the outermost compositions. The spherulitic growth of both PLA and PCL in the blends was followed by polarized optical microscopy at 140 and 37°C. From tensile tests at speed of 50 mm/min Young's modulus values between 5.2 and 0.4 GPa, strength values between 56 and 12 MPa, and strain at break values between 1 and 400% were obtained varying the blend composition. The viscoelastic properties (E′ and tan δ) obtained at frequency of 1 Hz by DMA are discussed and are found consistent with composition, phase separation, and crystallization behavior of the blends. POLYM. ENG. SCI., 46:1299–1308, 2006. © 2006 Society of Plastics Engineers     

Preparation and characterization of poly(lactic acid)/recycled polypropylene blends with and without the coupling agent,n-(6-aminohexyl)aminomethyltriethoxysilane

Blends of polylactide (PLA) and recycled polypropylene (rPP) were prepared by melt-processing using a corotating twin-screw extruder and subsequent pelletizing of the extrudates for injection molding. The PLA/rPP blends were characterized by Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), rheometer (MCR-102), scanning electron microscopy(SEM), tensile tests, and impact measurements. The results indicate that the PLA/rPP blend is immiscible and has a two-phase structure. TGA revealed enhancement of the thermal stability of the blends upon addition of rPP. The storage modulus, loss modulus, and complex viscosity of the blends increased with rPP concentration. Mechanical studies showed that introduction of rPP results in a decrease in tensile strength and modulus and enhancement of the impact strength of PLA in the blends. The effects of a silane coupling agent on the morphology and on the tensile and impact properties of the rPP blends of silane-modified PLA were also examined. SEM studies suggest that silane is an effective interfacial modifier. Thus, better interfacial adhesion was observed with silane-modified blends as compared with unmodified blends. Silane also improved the mechanical properties of the modified blends. The blends reached maximum tensile strength at 1.5 wt.% silane (relative to modified PLA content), and impact strength increased with increasing silane concentration. These results confirm the enhancing effect of silane on modified PLA/rPP blends.     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Enhancement of PVC/ENR blend properties by poly(methyl acrylate) grafted oil palm empty fruit bunch fiber

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150°C, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Young's modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Young's modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the impact strength, UTS, and elongation at break of the composites were found to decrease with the increase in fiber loading. An increase in elongation at break and UTS and decrease in the flexural and Young's modulus was observed with the addition of PMA‐g‐OPEFB fiber compared to ungrafted fiber. This observation indicates that grafting of PMA onto OPEFB impart some flexibility to the blend. The morphology of cryogenically fractured and tensile fracture surfaces of the composites, examined by a scanning electron microscope shows that the adhesion between the fiber and the matrix is improved upon grafting of the OPEFB fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008