Microstructure and properties of carbon fiber sized with pickering emulsion based on graphene oxide sheets and its composite with epoxy resin

The Graphene oxide (GO) sheets were used for preparing the epoxy resin Pickering emulsion. The particle size and the zeta potential of the Pickering emulsion were measured to evaluate its stability. The stable emulsion could be served as the film former of sizing agent for carbon fiber (CF). The effect of the Pickering emulsion stabilized by GO sheets on the properties of CF and the interfacial adhesion property of CF reinforced composite were investigated. Scanning electron microscopy (SEM) images showed that there existed a layer of sizing agent film with GO sheets evenly on the CF surface. Abrasion resistance and stiffness values of CF were tested and the results indicated that the sized CF conformed to the requirement of CF handleability. The interlaminar shear strength (ILSS) test indicated that the interfacial adhesion of the composite could be greatly improved. The fracture surfaces of CF composites were examined by SEM after ILSS tests. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42285.     

Interfacial microstructure and properties of carbon fiber-reinforced unsaturated polyester composites modified with carbon nanotubes

To improve the interfacial properties in carbon fiber (CF)-reinforced unsaturated polyester (UP) composites, we directly introduced functionalized carbon nanotubes dispersed in the fiber sizing onto the fiber surface. For comparing the influence of polymer type on sizing effect, two different polymers (UP MR13006 and water-soluble epoxy (EP)) were used to prepare sizing agent. Morphology and surface energy of CFs were examined by scanning electron microscopy and dynamic contact angle analysis test. Tensile strength was investigated in accordance with ASTM standards. Mechanical properties of the composites were investigated by interlaminar shear strength (ILSS) and impact toughness. Test results indicate that TS, ILSS, and impact toughness were enhanced simultaneously. For UP matrix, the sizing agent containing UP has better reinforcing and toughening effect than the sizing agent containing water-soluble EP.     

Preparation of emulsion‐type thermotolerant sizing agent for carbon fiber and the interfacial properties of carbon fiber/epoxy resin composite

A modified resin was synthesized through the reaction between dodecylamine and tetraglycidyldiaminodiphenylmethane (TGDDM), which was used as the film former of sizing agent for carbon fiber (CF). The sizing agents were prepared through phase inversion emulsification method. Fourier transform infrared spectroscopy (FTIR) was utilized to analyze the modified resin. Particle sizes of the sizing agents were tested to evaluate their stabilities. Differential scanning calorimetry (DSC) results demonstrated that the glass transition temperature (T_g) of the modified TGDDM is much higher than the T_g of the cured epoxy resin E‐44. The influences of the sizing treatment on CF were investigated by abrasion resistance, fluffs, and stiffness tests. The maximum abrasion resistance increased by 172.8%, compared with the abrasion resistance of the desized CF. Interlaminar shear strength (ILSS) results of the CF/TGDDM composites indicated that the interfacial adhesion between CF and matrix resin was greatly improved after CF was sized. The maximum ILSS value could obtain a 29.16% improvement, compared with the ILSS of the desized CF composite. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41882.     

Study on the mechanical properties and microstructure of high-performance carbon fiber/epoxy composites

A high-toughness epoxy has been prepared using carboxyl-terminated butadiene acrylonitrile (CTBN) as a toughening agent to modify the AG-80 epoxy resin. High-performance carbon fiber/epoxy (CF/EP) composites are fabricated using the CTBN-toughened epoxy resin as the matrix and two types of CF, namely, T800SC and T800HB, as reinforcement. The mechanical properties of the matrix, surface properties of the CFs, tensile properties, and fracture morphologies of the composites are systematically investigated to elucidate the key factors influencing interfacial bonding in high-performance CF/EP composites. The results reveal that the most significant improvement in toughness is achieved when the CTBN content is 6.90 wt.% in the epoxy resin. Owing to the high content of polar functional groups and excellent surface wettability of T800SC, the T800SC/EP composite exhibits superior mechanical properties compared with the T800HB/EP composite.     

Incorporation of silicon dioxide nanoparticles at the carbon fiber‐epoxy matrix interphase and its effect on composite mechanical properties

Functionalized silicon dioxide nanoparticles (nano‐fSiO₂) were uniformly deposited on the surface of carbon fibers (CFs) using a coating process which consisted of immersing the fibers directly in a suspension of nano‐fSiO₂ particles and epoxy monomers in 1‐methyl‐2‐pyrrolidinone (NMP). The 0° flexural properties, 90° flexural properties, and Interlaminar shear strength (ILSS) mechanical properties of unidirectional epoxy composites made with nano‐fSiO₂+epoxy sized carbon fibers, with control fibers, and with epoxy‐only sized fibers were measured and compared. An obvious increase of the fiber/matrix adherence strength was obtained with the nano‐fSiO₂+epoxy coating. The nano‐fSiO₂+epoxy sized CF/epoxy composites showed a relative increase of 15%, 50%, and 22% in comparison to control fibers, for the Interlaminar shear strength, the 90^° flexural strength and the 90° flexural modulus, respectively, but little e difference was measured between the different systems for the 0° flexural properties. The observation of the fracture surfaces by scanning electron microscopy of composite fracture confirmed the improvement of the interfacially dependent mechanical properties. POLYM. COMPOS., 38:1474–1482, 2017. © 2015 Society of Plastics Engineers     

Preparation and properties of water‐soluble‐type sizing agents for carbon fibers

A water‐soluble epoxy resin was synthesized by the reaction between novolac epoxy resin (F‐51) and diethanolamine. Then, the modified F‐51 was mixed with poly(alkylene glycol allyl glycidyl ether) as a film former of a sizing agent. A series of water‐soluble sizing agents for carbon fiber (CF) were prepared. The modified F‐51 was analyzed by Fourier Transform infrared spectroscopy. The surface morphology of the CF was characterized by scanning electron microscopy. The effects of the sizing agent on the handling characteristics were investigated by abrasion resistance, fluffs, and breakage and stiffness tests. The results show that the abrasion resistance of the sized CF increased by 114.5% and reached 2344 times and the mass of fabric hairiness decreased to 3.2 mg. The interlaminar shear strength (ILSS) test indicated that the interfacial adhesion of the composite could be greatly improved. The ILSS of the sized CF composite could reach a maximum value of 42.40 MPa. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39843.     

Evolution of the wettability between carbon fiber and epoxy as a function of temperature and resin curing

This article focuses on experimental studies on the wetting behavior between different carbon fibers (CFs) and epoxy as function of temperature, hardener addition, and progressive curing of the resin. The results indicate that surface sizing plays a key role in wettability of the CF with epoxy. There is a critical temperature for good‐wetting of DGEBA‐DDS mixture/CF. Complete wetting can be obtained for resin/CF after a period of curing time. Moreover, chemical reactions can not only improve the wettability but also strengthen interactions between the curing resin and CF. These results could provide an essential implication for understanding the formation process of interphase region of CF/epoxy composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Temperature effect on interfacial bonding property of single‐carbon fiber/epoxy resin composite

The changes in interfacial fracture energy of three kinds of commercially sized carbon fiber (CF)/epoxy resin composites in the range from ambient temperature to 130°C were investigated using the single‐fiber fragmentation test to evaluate the heat resistance of the interphase. The effects of CF sizing on the interfacial bonding property were studied using desized CF/epoxy resin composites. Thermogravimetric analysis and differential scanning calorimetry of the combination of sizing and matrix were employed to investigate the role of sizing on the variations in the fiber/matrix interfacial property under elevated temperature. The interfacial fracture energy values of all the studied CF composites were found to decrease quickly during the initial stage of temperature rise and drop gradually at higher temperature. At elevated temperature, the desized CF composites had higher heat resistance than the corresponding sized fiber composites. The differences in the interfacial heat resistance among the three kinds of CF composites and the difference in the interfacial thermal stability between the sized and the desized fiber composites were related to different glass transition temperatures of the interphases. The interaction between sizing and the matrix and the chain motion of the crosslink structure of the interphase has been suggested to determine the interfacial heat resistance. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Interface improvement of carbon fiber/methylphenylsilicone resin composites by fiber surface coating of polyhedral oligomeric silsesquioxanes

To enhance interfacial properties of carbon fibers (CFs)-reinforced methylphenylsilicone resin (MPSR) composites, we introduced an appropriate interface reinforced by trisilanolphenyl-polyhedral oligomeric silsesquioxanes (trisilanolphenyl-POSS) between CFs and MPSR with a liquid phase deposition strategy. Chemical bonds among silanol groups of trisilanolphenyl-POSS, hydroxyl-functionalized CF (CF–OH), and silanol end groups of MPSR in the coating were expected to be formed through condensation reaction during the prepared process. CFs with and without sizing treatment-reinforced MPSR composites were prepared by a compression molding method. X-ray photoelectron spectroscopy revealed that trisilanolphenyl-POSS particles enhanced the contents of fiber surface oxygen-containing groups and silicon-containing functional groups. Scanning electron microscopy and atomic force microscopy images showed that trisilanolphenyl-POSS nanoparticles have been introduced onto the fiber surface obviously and the surface roughness increased sharply. Dynamic contact angle analysis indicated that trisilanolphenyl-POSS-modified sizing agent could improve the fiber wettability and surface energy significantly. Short-beam bending test and impact toughness test results showed that the interlaminar shear strength and impact resistance of the sized CFs composites were enhanced greatly with increasing amplitudes of more than 35 and 27% in comparison with those of untreated CF composites, respectively. Cryo-fractured surface topographies of composites confirmed that interfacial adhesion between CFs and MPSR has been improved after sizing treatment. Meanwhile, the sizing treatment does not decrease single fiber tensile strength.     

Effects of novolac resin modification on mechanical properties of carbon fiber/epoxy composites

The epoxy resin matrix of carbon fiber (CF)‐reinforced epoxy composites was modified with novolac resin (NR) to improve the matrix‐dominated mechanical properties of composites. Flexural strength, interlaminar shear strength (ILSS), and impact strength were measured with unfilled, 7 wt% NR, 13 wt% NR, and 18 wt% NR filled to epoxy to identify the effect of adding NR on the mechanical properties of composites. The results showed that both interfacial and impact properties of composites were improved except for flexural property. The largest improvement in ILSS and impact strength were obtained with 13 wt% loading of NR. ILSS and impact strength were improved by 7.3% and 38.6%, respectively, compared with the composite without NR. The fracture and surface morphologies of the composite specimens were characterized by scanning electron microscopy. Intimate bonding of the fibers and the matrix was evident with the content of 7–13 wt% NR range. Decrease of crosslinking density and formation of NR transition layer were deduced with adding NR. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers     

Effects of surface treatment of carbon fiber: Tensile property,surface characteristics,and bonding to epoxy

In this article, effects of electrochemical oxidation and sizing treatment of PAN‐based carbon fibers (CFs) on the tensile properties, surface characteristics, and bonding to epoxy were investigated. As found, the electrochemical oxidation improves the tensile strength of single CF by 16.0%, due to weakening the surface stress concentration and smoothing the surface structure. Further sizing treatment shows a negligible effect on the tensile strength. Both oxidation and sizing treatments significantly improve the wettability and surface energies of CFs by introducing oxygen‐containing functional groups. Microbond test was conducted to characterize the interfacial shear strength (IFSS) between a single fiber and an epoxy droplet. The oxidation treatment increases IFSS slightly, which is due to the contradictory effects of the formation of chemical bonds between the resin and CFs, and the reduced mechanical interlocking. Further sizing treatment significantly enhances IFSS from 73.6 to 81.0 MPa, due to the formation of vast chemical bonds. Furthermore, the oxidation and sizing treatment can effectively reduce the degradation of IFSS to the hygrothermal ageing for the CF/epoxy system. POLYM. COMPOS., 37:2921–2932, 2016. © 2015 Society of Plastics Engineers     

酸化石墨烯改性环氧树脂及其碳纤维复合材料力学性能研究

针对石墨烯在复合材料增强增韧上的应用,对石墨烯进行了酸化处理,采用超声分散方法制备酸化石墨烯/环氧树脂(EP)浇注体,并在此基础上制备了酸化石墨烯/碳纤维(CF)/环氧树脂(EP)复合材料。分别利用红外光谱和透射电镜表征了酸化石墨烯表面结构和微观形貌,利用拉伸、弯曲、冲击等机械测试手段评价了酸化石墨烯改性EP和CF-EP的力学性能,并利用扫描电镜对复合材料拉伸断面形貌进行观察。试验结果表明:石墨烯酸化处理后,成功在表面引入了羟基、羧基等极性基团;酸化石墨烯可对EP和CF/EP进行有效增强增韧,当其添加量为0.2wt%时,EP拉伸强度和冲击强度分别提高了23.3%和109.8%,CF/EP拉伸强度、弯曲强度分别提高了6.0%和10.6%,当酸化石墨烯添加量为0.5wt%时,CF/EP复合材料层间剪切强度提高了7.4%。微观形貌分析表明,酸化石墨烯对CF/EP增强改性主要是通过对EP进行增强增韧,同时提高CF和EP之间的界面性能来实现的。     

Enhanced interfacial strength and mechanical properties of carbon fiber composites by introducing functionalized silica nanoparticles into the interface

Introducing nanoparticles onto the surface of carbon fibers (CFs) is a useful method for enhancing the quality of fiber-matrix interface. In this work, a liquid sizing agent containing functionalized silica nanoparticles (SiO₂) was well prepared to improve interfacial strength and mechanical properties of composites. In order to enhance the dispersion of SiO₂ nanoparticles in sizing agent, SiO₂ nanoparticles were chemically grafted with 3-aminopropyltriethoxysilane (APS), and then silanized silica (SiO₂-APS) was introduced into the interphase by a conventional sizing process as well. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) confirmed the successful preparation of SiO₂-APS. Scanning electron microscopy (SEM) showed that a uniform distribution of SiO₂-APS on the fiber surface and the increased surface roughness. The sized fibers (CF/SiO₂-APS) exhibited a high surface free energy and good wettability based on a dynamic contact angle testing. Interfacial microstructure and mechanical properties of untreated and sized CFs composites were investigated. Simultaneous enhancements of interlaminar shear strength (ILSS) and impact toughness of CF/SiO₂-APS composites were achieved, increasing 44.79% in ILSS and 31.53% in impact toughness compared to those of untreated composites. Moreover, flexural strength and modulus of composites increased by 32.22 and 50.0% according to flexural test. In addition, the hydrothermal aging resistance of CF/SiO₂-APS composites has been improved significantly owing to the introduced Si-O-Si bonds at the interface.     

Effects of sizing materials on the properties of carbon fiber‐reinforced polyamide 6,6 composites

This article aims to study the effect of the sizing materials type on the mechanical, thermal, and morphological properties of carbon fiber (CF)‐reinforced polyamide 6,6 (PA 6,6) composites. For this purpose, unsized CF and sized CFs were used. Thermogravimetric analysis was performed, and it has been found that certain amounts of polyurethane (PU) and PA sizing agents decompose during processing. The effects of sizing agent type on the mechanical and thermomechanical properties of all the composites were investigated using tensile, Izod impact strength test, and dynamic mechanical analysis. Tensile strength values of sized CF‐reinforced composites were higher than that of unsized CF‐reinforced composites. PA and polyurethane sized CF‐reinforced composites exhibited the highest impact strength values among the other sized CF‐reinforced composites. PU and PA sized CF‐reinforced composites denoted higher storage modulus and better interfacial adhesion values among the other sizing materials. Scanning electron microscope studies indicated that CFs which were sized with PU and PA have better interfacial bonding with PA 6,6 matrix among the sized CFs. All the results confirmed that PA and PU were suitable for CF's sizing materials to be used for PA 6,6 matrix. POLYM. COMPOS., 34:1583–1590, 2013. © 2013 Society of Plastics Engineers     

Influence of new thermoplastic sizing agents on the mechanical behavior of poly(ether ketone ketone)/carbon fiber composites

In this study, unidirectional poly(ether ether ketone)/carbon fiber (CF) composite sheets were elaborated with unsized, epoxy‐sized, and thermoplastic‐sized CFs by hot‐press molding. The thermoplastic sizings that we used were poly(ether imide) (PEI) and poly(ether ketone ketone) oligomer aqueous dispersions. Scanning electron microscopy observation of the composites freeze fractures showed that unlike unsized or epoxy‐sized CFs, the thermoplastic sizings improved the interaction between the fibers and the matrix. A comparative study of the mechanical relaxations by dynamic mechanical analysis was carried out on the different composites before and after immersion in kerosene. At low temperature, the PEI sizing had a significant influence on the β relaxation, particularly after kerosene immersion. The thermoplastic sizings did not modify the glass‐transition temperature but improved the kerosene resistance on the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42550.     

Resin modification on interlaminar shear property of carbon fiber/epoxy/nano‐CaCO3 hybrid composites

Epoxy resin was modified by adding a silane coupling agent/nano‐calcium carbonate master batch. Then, samples of binary carbon fiber/epoxy composites and ternary fiber/nano‐CaCO₃/epoxy were prepared by hot press process. The interlaminar shear strength (ILSS) of the carbon fiber/epoxy composites was investigated and the results indicate that introduction of the treated nano‐CaCO₃ enhances ILSS obviously. In particular, the addition of 4 wt% nano‐CaCO₃ leads to 36.6% increase in the ILSS for the composite. The fracture surfaces of the carbon fiber/epoxy composites and the mechanical properties of epoxy resin cast are examined and both of them are employed to explain the change of ILSS. The results show that the change of ILSS is primarily due to an increase of the epoxy matrix strength and an increase of the fiber/epoxy interface. The bifurcation of propagating cracks, stress transfer, and cavitation are deduced for the reasons of strengthening and toughening effect of nano‐CaCO₃ particles. POLYM. COMPOS., 38:2035–2042, 2017. © 2015 Society of Plastics Engineers     

Improving the interfacial properties of carbon fiber–epoxy resin composites with a graphene-modified sizing agent

We successfully prepared a graphene-modified carbon fiber (CF) sizing agent with good dispersity and stability by dispersing reduced graphene oxide (RGO) into an emulsion-type sizing agent. RGO was obtained by the reduction of graphene oxide (GO) with the help of gallic acid. The influence of the graphene-modified sizing agent on the interfacial properties of the CF–epoxy resin composites was investigated with microbond testing and the three-point bending method. The results show that optimized interfacial properties were achieved when the size of the modified graphene was less than 1 μm, the content of RGO was 20 ppm, and the pH value of the sizing agent was 10.5. The interfacial shear strength of the composites reached 92.3 MPa, which was 29.6% higher than that of the composites with unmodified CFs. Compared with commercial-CF-fabric-reinforced composites, the interlaminar shear strength of the composites treated with the RGO-modified sizing agent increased by 21.5%. Both the interfacial and interlaminar failure morphologies of the composites were examined with scanning electron microscopy (SEM). The results show that a large amount of residual resin adhered to the surfaces of the CFs treated with the RGO-modified sizing agent; this indicated good interfacial properties between the CFs and the resin matrix. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47122.     

Effect of various methods of pre-treatment of carbon fibers on the mechanical properties of PIP-based ceramics/carbon composites

The purpose of the work was to determine the conditions of CF preparation to obtain carbide composites with favorable mechanical response. The relationships between the interfacial properties of fiber/polymethylsiloxane composite, and mechanical properties of the resulting fiber/carbide composites were investigated. The CF/resin interfacial strength was modified by oxidation of CF surface with nitric acid, silanization, and depositing CNT or a pyrolytic carbon layer (PyC). The study of composite interphases (ILSS and SEM) and surface tests of the modified CF (XPS, FT-IR, wettability measurements) showed different nature of the bonding occurring at the fiber/resin and fiber/ceramics boundary. The CF silanization significantly improved the ILSS between CFs and resin by 38.5%, while reduced flexural properties of carbide composites. The most promising treatment method of CF for PIP-based ceramic composites was modification with PyC, which provided 2 times higher ILSS, 1.5 times higher flexural strength and improved work to fracture (WF) as compared to unmodified CF.     

Development of multiwalled‐carbon‐nanotube‐welded carbon fibers and evaluation of the interfacial strength in epoxy composites

Multiwalled carbon nanotube (MWCNT)‐welded carbon fibers (CFs) were prepared by a three‐step process, which included polyacrylonitrile (PAN) coating, MWCNT absorption, and heat treatment. The structure of these materials was characterized by scanning electron microscopy, Fourier‐transform infrared spectroscopy, and Raman spectroscopy. The MWCNTs were uniformly assembled on the surface of the PAN‐coated CFs and welded by a PAN‐based carbon layer after heat treatment. The contact angle of the MWCNT‐welded CFs in the epoxy resins was 41.70°; this was 22.35% smaller than that of the unsized CFs. The interfacial shear strength (IFSS) of the MWCNT‐welded CF–epoxy composite was 83.15 MPa; this was 28.89% higher than that of the unsized CF–epoxy composite. The increase in the IFSS was attributed to the enhancement of adhesions between the CFs and polymer matrix through the welding of the MWCNTs on the CFs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45027.     

Effect of sizing on interfacial adhesion of commercial high strength carbon fiber‐reinforced resin composites

The influence of sizing agent on interfacial shear strength (IFSS) of carbon fiber/epoxy (CF/EP) and carbon fiber/bismaleimide (CF/BMI) was investigated. Since sizing agent can alter physicochemical properties of CF surface, possible affecting factors, including sizing reactivity, chemical reactions between sizing and resin, wettability of fiber with resin, fiber surface roughness, and chemical composition of fiber surface, were discussed. It is found that contact angle of fiber with resin and sufficient chemical reactions between sizing and resin reveal strong correlation with the interfacial adhesion of CF/EP and CF/BMI, while the effect of surface roughness and the amount of oxygen on the fiber surface are relatively weak. Due to EP type of the composition, the sizing agent tends to improve the wettability of CF with EP, while goes against for the fiber with BMI. POLYM. COMPOS., 254–261, 2016. © 2014 Society of Plastics Engineers