Comparison of AlPO4- and Co3(PO4)2-coated LiNi0.8Co0.2O2 cathode materials for Li-ion battery

Electrochemical and thermal properties of Co₃(PO₄)₂- and AlPO₄-coated LiNi_0.8Co_0.2O₂ cathode materials were compared. AlPO₄-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 170.8 mAh g⁻¹ and had a capacity retention (89.1% of its initial capacity) between 4.35 and 3.0 V after 60 cycles at 150 mA g⁻¹. Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 177.6 mAh g⁻¹ and excellent capacity retention (91.8% of its initial capacity), which was attributed to a lithium-reactive Co₃(PO₄)₂ coating. The Co₃(PO₄)₂ coating material could react with LiOH and Li₂CO₃ impurities during annealing to form an olivine Li_xCoPO₄ phase on the bulk surface, which minimized any side reactions with electrolytes and the dissolution of Ni⁴⁺ ions compared to the AlPO₄-coated cathode. Differential scanning calorimetry results showed Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathode material had a much improved onset temperature of the oxygen evolution of about 218 °C, and a much lower amount of exothermic-heat release compared to the AlPO₄-coated sample.     

Novel high-capacity hybrid layered oxides NaxLi1.5-xNi0.167Co0.167Mn0.67O2 as promising cathode materials for rechargeable sodium ion batteries

Relatively low capacity is a technological bottleneck of the development of sodium ion batteries. Herein, we present a series of hybrid layered cathode materials Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ (x?=?0.5, 0.6, 0.7, 0.8, 0.9, 1) with composite crystalline structures, which are prepared by co-precipitation method. The combined analysis of XRD, SEM and TEM reveals that the materials are composed of P2 structure, α-NaFeO₂ structure and small amount of Li₂MnO₃. Among the as-prepared materials, Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ delivers an initial reversible capacity of 222?mA?h?g^?1 at 20?mA?g^?1. Even at 100?mA?g^?1, it shows a remarkable discharge capacity of 125?mA?h?g^?1 in the first cycle and remains 60?mA?h?g^?1 after 300 cycles. Such high capacity is achieved by the specific composite structure and sodium ions are proved to be able to intercalate/deintercalate in Li_1.5Ni_0.167Co_0.167Mn_0.67O₂ with α-NaFeO₂ structure. The Ex-situ XRD results of Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ in the first cycle show that the P2 structure is well maintained along with irreversible phase transition of α-NaFeO₂ structure, which is responsible for the long-term capacity fading. Owing to the high discharge capacity, the novel hybrid layered oxides Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ with composite structures can be considered as promising cathode materials to promote progress toward sodium-ion batteries.     

A simple and effective method to synthesize layered LiNi0.8Co0.1Mn0.1O2 cathode materials for lithium ion battery

Nanocrystalline materials of Ni_0.8Co_0.1Mn_0.1(OH)₂ are successfully synthesized by fast co-precipitation method. The crystalline structure and morphology of the precursors and LiNi_0.8Co_0.1Mn_0.1O₂ materials are characterized by XRD, SEM and Rietveld refinement analyses. It is found that the nanocrystalline phase and low crystallinity of Ni_0.8Co_0.1Mn_0.1(OH)₂ could help achieve its uniform mixing with lithium source, and further attribute to highly ordered layered LiNi_0.8Co_0.1Mn_0.1O₂ with low cation mixing degree. Electrochemical studies confirm that the LiNi_0.8Co_0.1Mn_0.1O₂ exhibits a good electrochemical property with initial discharge specific capacity of 192.4 mAh g^− 1 at a current density of 18 mA g^− 1, and the capacity retention after 40 cycles is 91.56%. This method is a simple and effective method to synthesize cathode material.     

Effects of surface modification on the cycling stability of LiNi0.8Co0.2O2 electrodes by CeO2 coating

A high-performance LiNi_0.8Co_0.2O₂ cathode was successfully fabricated by a sol-gel coating of CeO₂ to the surface of the LiNi_0.8Co_0.2O₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiNi_0.8Co_0.2O₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Unlike pristine LiNi_0.8Co_0.2O₂, the CeO₂-coated LiNi_0.8Co_0.2O₂ cathode exhibits no decrease in its original specific capacity of 182 mAh/g (versus lithium metal) and excellent capacity retention (95% of its initial capacity) between 4.5 and 2.8 V after 55 cycles. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Performance of LiNi1/3Co1/3Mn1/3O2 prepared from spent lithium-ion batteries by a carbonate co-precipitation method

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ cathode particles were resynthesized by a carbonate co-precipitation method using spent lithium-ion batteries (LIBs) as a raw material. The physical characteristics of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, the (Ni_1/3Co_1/3Mn_1/3)₃O₄ intermediate, and the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material were investigated by laser particle-size analysis, scanning electron microscopy–energy-dispersive spectroscopy (SEM-EDS), thermogravimetry–differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), inductively coupled plasma–atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ was studied by continuous charge–discharge cycling and cyclic voltammetry. The results indicate that the regenerated Ni_1/3Co_1/3Mn_1/3CO₃ precursor comprises uniform spherical particles with a narrow particle-size distribution. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ comprises spherical particles similar to those of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, but with a narrower particle-size distribution. Moreover, it has a well-ordered layered structure and a low degree of cation mixing. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ shows an initial discharge capacity of 163.5 mA h g^?1 at 0.1 C, between 2.7 and 4.3 V; the discharge capacity at 1 C is 135.1 mA h g^?1, and the capacity retention ratio is 94.1% after 50 cycles. Even at the high rate of 5 C, LiNi_1/3Co_1/3Mn_1/3O₂ delivers the high capacity of 112.6 mA h g^?1. These results demonstrate that the electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ is comparable to that of a cathode synthesized from fresh materials by carbonate co-precipitation.     

WO3 membrane-encapsulated layered LiNi0.6Co0.2Mn0.2O2 cathode material for advanced Li-ion batteries

Despite Nickel-rich materials have all the advantages of high capacity, long cycle life and low cost, there is still a disadvantage that the capacity decreases rapidly as the number of cycles increases. In order to solve this problem, WO₃ was uniformly coated on the surface of LiNi_0.6Co_0.2Mn_0.2O₂ cathode materials by wet coating, and its cycling performance was greatly improved with the higher capacity. The coated materials were analyzed by X-ray diffraction(XRD), Scanning electron microscope (SEM), high resolution Transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy(XPS). The results showed that the coating thickness was around 3.15?nm, and some tungsten ions were doped into the lattice of the near surface area of the LiNi_0.6Co_0.2Mn_0.2O₂ material. In addition, the results of charge-discharge test showed that 1?wt%WO₃ coating LiNi_0.6Co_0.2Mn_0.2O₂ had the best performance, and delivered a discharge capacity of 140 mAh g^?1 (the capacity retention rate is 84.8%) in the potential interval of 2.8–4.3?V at 1?C (1?C?=?165?mA?g^?1) after 200 cycles, while the bare cathode material only delivered a discharge capacity of 120 mAhg^?1 (the capacity retention rate is 75%). The phenomenon indicates that the WO₃ coating plays a role in inhibiting the harmful side reactions between the cathode material and the electrolyte, improving the electrochemical and structure stability of LiNi_0.6Co_0.2Mn_0.2O₂ cathode materials.     

Synthesis and improved electrochemical performance of Al (OH)3-coated Li[Ni1/3Mn1/3Co1/3]O2 cathode materials at elevated temperature

Spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ powders were synthesized from LiOH·H₂O and coprecipitated spherical metal hydroxide, (Ni_1/3Mn_1/3Co_1/3)(OH)₂ and coated with Al(OH)₃. The Al(OH)₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ showed a capacity retention of 80% at 320 mA g⁻¹ (2 C-rate) based on 20 mA g⁻¹ (0.1 C-rate), while the pristine Li[Ni_1/3Co_1/3Mn_1/3]O₂ delivered only 45% at the same current density. Also, unlike pristine Li[Ni_1/3Co_1/3Mn_1/3]O₂, the Al(OH)₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode exhibits excellent rate capability and good thermal stability.     

Characterization of yttrium substituted LiNi0.33Mn0.33Co0.33O2 cathode material for lithium secondary cells

LiNi_0.33−xMn_0.33Co_0.33Y_xO₂ materials are synthesized by Y³⁺ substitute of Ni²⁺ to improve the cycling performance and rate capability. The influence of the Y³⁺ doping on the structure and electrochemical properties are investigated by means of X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS) and galvanostatic charge/discharge tests. LiNi_0.33Mn_0.33Co_0.33O₂ exhibits the capacity retentions of 89.9 and 87.8% at 2.0 and 4.0 C after 40 cycles, respectively. After doping, the capacity retentions of LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ are increased to 97.2 and 95.9% at 2.0 and 4.0 C, respectively. The discharge capacity of LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ at 5.0 C remains 75.7% of the discharge capacity at 0.2 C, while that of LiNi_0.33Mn_0.33Co_0.33O₂ is only 47.5%. EIS measurement indicates that LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ electrode has the lower impedance value during cycling. It is considered that the higher capacity retention and superior rate capability of Y-doped samples can be ascribed to the reduced surface film resistance and charge transfer resistance of the electrode during cycling.     

LiNi0.8Co0.15Al0.05O2 cathode materials prepared by TiO2 nanoparticle coatings on Ni0.8Co0.15Al0.05(OH)2 precursors

Synthesis, electrochemical, and structural properties of LiNi_0.8Co_0.15Al_0.05O₂ cathodes prepared by TiO₂ nanoparticles coating on a Ni_0.8Co_0.15Al_0.05(OH)₂ precursor have been investigated by the variation of coating concentration and annealing temperature. TiO₂-coated cathodes showed that Ti elements were distributed throughout the particles. Among the coated cathodes, the 0.6 wt% TiO₂-coated cathode prepared by annealing at 750 °C for 20 h exhibited the highest reversible capacity of 176 mAh g⁻¹ and capacity retention of 92% after 40 cycles at a rate of 1C (=190 mA g⁻¹). On the other hand, an uncoated cathode showed a reversible first discharge capacity of 186 mAh g⁻¹ and the same capacity retention value to the TiO₂-coated sample at a 1C rate. However, under a 1C rate cycling at 60 °C for 30 cycles, the uncoated sample showed a reversible capacity of 40 mAh g⁻¹, while a TiO₂-coated one showed 71 mAh g⁻¹. This significant improvement of the coated sample was due to the formation of a possible solid solution between TiO₂ and LiNi_0.8Co_0.15Al_0.05O₂. This effect was more evident upon annealing the charged sample while increasing the annealing temperature, and at 400 °C, the coated one showed a more suppressed formation of the NiO phase from the spinel LiNi₂O₄ phase than the uncoated sample.     

Preparation of LiNi1/3Co1/3Mn1/3O2/polytriphenylamine cathode composites with enhanced electrochemical performances towards reversible lithium storage

A series of LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine composites were successfully synthesized by ultrasound dispersion method. LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine (5.0?wt%) composite with small and homogeneous particle size exhibited excellent electrochemical performance, which delivered an initial discharge capacity of 223.7?mAh g^?1 with a capacity retention of 84.39% after 100 cycles in the voltage range of 2.5–4.5?V and at a current density of 0.2C. Moreover, an excellent specific discharge capacity of 127.3?mAh g^?1 at a current density 5C indicates a superior rate performance of the LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine (5.0?wt%) composite. The good electrochemical performances of the composite can be attributed to the introduction of polytriphenylamine, which increased electrical conductivity, decreased charge transfer resistance and increased Li⁺ ion diffusion ability. These noteworthy results demonstrated that LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine composites might be potential cathode materials for lithium ion batteries.     

LiNi0.1Mn0.1Co0.8O2 electrode material: Structural changes upon lithium electrochemical extraction

We reported here on the synthesis, the crystal structure and the study of the structural changes during the electrochemical cycling of layered LiNi_0.1Mn_0.1Co_0.8O₂ positive electrode material. Rietveld refinement analysis shows that this material exhibits almost an ideal α-NaFeO₂ structure with practically no lithium-nickel disorder. The SQUID measurements confirm this structural result and evidenced that this material consists of Ni²⁺, Mn⁴⁺ and Co³⁺ ions.Unlike LiNiO₂ and LiCoO₂ conventional electrode materials, there was no structural modification upon lithium removal in the whole 0.42 ≤ x ≤1.0 studied composition range. The peaks revealed in the incremental capacity curve were attributed to the successive oxidation of Ni²⁺ and Co³⁺ while Mn⁴⁺ remains electrochemically inactive.     

Magnesium ferrite nanoparticles as a magnetic sorbent for the removal of Mn2+, Co2+, Ni2+ and Cu2+ from aqueous solution

The aim of this research was to prepare magnesium ferrite (MgFe₂O₄) magnetic nanoparticles and to investigate their sorption characteristics towards Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺ ions in aqueous solution. MgFe₂O₄ was synthesized by glycine-nitrate combustion method and was characterized by low crystallinity with crystallite size of 8.2?nm, particle aggregates of 13–25?nm, BET surface area of 14?m²/g and pore size of 8.0?nm. Sorption properties of MgFe₂O₄ towards Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺ ions were studied using one-component model solutions and found to be dependent on metal ions concentration, contact time, pH and conditions of regeneration experiment. The highest sorption capacity of MgFe₂O₄ was detected towards Co²⁺ (2.30?mmol?g¹) and Mn²⁺ (1.56?mmol?g^?1) and the lowest towards Ni²⁺ (0.89?mmol?g^?1) and Cu²⁺ (0.46?mmol?g^?1). It was observed that sorption equilibrium occurs very quickly within 20–60?min. The pH_zpc of sorbent was calculated to be 6.58. At studied pH interval (3.0–7.0) the sorption capacity of MgFe₂O₄ was not significantly affected. Regeneration study showed that the metal loaded sorbent could be regenerated by aqueous solution of 10^?3 M MgCl₂ at pH 6.0 within 120?min of contact time. Regeneration test suggested that MgFe₂O₄ magnetic sorbent can be efficiently used at least for four adsorption-desorption cycles. The high sorption properties and kinetics of toxic metal ion sorption indicates good prospects of developed sorbent in practice for wastewater treatment.     

Fabrication and characterization of monodispersed Mn0.8Ni0.2Co2O4 mesoporous microspheres for supercapacitor application

The monodispersed Ni doped MnCo₂O₄ mesoporous microspheres were synthesized through a simple ammonium bicarbonate-assisted solvothermal route. The spinel-type crystal structure with a lattice parameter of 8.199?Å for Mn_0.8Ni_0.2Co₂O₄ composition was obtained by using X-ray diffraction analysis. The Brunauer?Emmett?Teller (BET) specific surface area of the sample was found to be 75.78?m² g^?1 with an average pore diameter of 9.88?nm. Electron microscopy studies revealed that the stable mesoporous microspheres are constituted by well-connected aggregates of nanoparticles. The influence of Ni doping on the pseudo-capacitance of MnCo₂O₄ electrode was investigated by means of cyclic voltammetry in 6?M KOH electrolyte. We found that the spinel-type Mn_0.8Ni_0.2Co₂O₄ mesoporous microspheres exhibit specific capacitances of 1822 F g^?1 at a scan rate of 5?mV/s. Furthermore, the electrochemical impedance spectroscopy analysis revealed the low resistance and good electrochemical stability of the sample.     

Modification of LiNi0.5Co0.2Mn0.3O2 with a NaAlO2 coating produces a cathode with increased long-term cycling performance at a high voltage cutoff

A long-lived cycling property is an important factor for the extensive use of the lithium-ion batteries. In this study, a NaAlO₂ layer was initially coated on the LiNi_0.5Co_0.2Mn_0.3O₂ surface. Electrochemical tests indicate that the coated surface achieves better cycling stability and a higher capacity at 25 °C. In addition, the 1 wt % NaAlO₂-coated sample exhibits the best performance, and it also exhibits a discharge specific capacity of 189.6 mAh∙g⁻¹ at 0.1C in the first cycle. After 800 cycles at 1C, the capacity retention of the 1 wt % NaAlO₂-coated sample is approximately 73.31%, a value that is 21.26% higher than the pristine sample. The electrochemical impedance spectroscopy (EIS) analysis reveals a decrease in the LiNi_0.5Co_0.2Mn_0.3O₂ charge transfer impedance and a significant increase in lithium ion diffusion after the application of the NaAlO₂ coating. The high ion diffusion coefficient and low charge transfer impedance are conducive to the better rate performance of NaAlO₂-coated LiNi_0.5Co_0.2Mn_0.3O₂.     

High-voltage electrochemical performance of LiNi0.5Co0.2Mn0.3O2 cathode materials via Al concentration gradient modification

Al₂O₃-modified LiNi_0.5Co_0.2Mn_0.3O₂ cathode material is successfully synthesized via a facile carboxymethyl cellulose (CMC)-assisted wet method followed by a high-temperature calcination process. Al concentration gradient doping and accompanying formation of Al-coating are simultaneously accomplished in the modified samples. XRD and EDS analysis demonstrate that Al element is successfully doped into the crystal lattice with concentration gradient distribution inside the particles, reducing the Li/Ni cation mixing and stabilizing the layered structure. The compact distribution of Al on the surface forms a protective layer between the electrodes and the electrolyte, prohibiting the harmful side reactions and phase transition on the interphase. Compared with the pristine, the modified material with 2000?ppm Al₂O₃ (Al-2000) shows the best high-voltage performance with the capacity retention increased by ~13.3% from 138.3 to 163.0 mAh g^?1 at 1?C in 3.0–4.6?V after 100 cycles. Even under the high current rate of 8?C (1240 mAh g^?1) after 200 cycles, the Al-2000 still exhibits a capacity retention of 88.6%, greater than 80.3% for the pristine. Furthermore, results from the cyclic voltammetry (CV) and the electrochemical impedance spectroscopy (EIS) measurements confirm the roles of the Al₂O₃ modification in decreasing polarization and electrochemical resistances, contributing to the kinetic process of electrodes.     

Effects of Al doping on the electrochemical performances of LiNi0.83Co0.12Mn0.05O2 prepared by coprecipitation

The Ni-rich LiNi_0.83Co_0.12Mn_0.05O₂ (NCM83) cathode materials have drawn intensive attention due to the high energy density and low cost. However, Ni-rich LiNi_1-x-yCo_xMn_yO₂ still has the fatal weakness of poor cycle stability, limiting its further wide application. Bulk doping is an effective means to enhance the cycle stability, yet the electrochemical performances are very sensitive to the doping quantity. Here a facile method of co-precipitation is adopted to coat (Ni_0.4Co_0.2Mn_0.4)_1-xAl_x(OH)_2+x on precursor particles of NCM83. Al ions diffuse evenly in the NCM83 particles after sintering. The cells are operated at a high cut-off voltage of 4.5 V. The discharge capacity of NCM83 is 187.8 mAh g^?1, and decays fast with cycles. The doped sample even exhibits a higher discharge capacity of 195 mAh g^?1, and the capacity retention is improved to 83.8% after 200 cycles.     

Synthetic optimization of spherical Li[Ni1/3Mn1/3Co1/3]O2 prepared by a carbonate co-precipitation method

A carbonate co-precipitation method was employed to prepare spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material. The precursor, [Ni_1/3Co_1/3Mn_1/3]CO₃, was prepared using ammonia as chelating agent under CO₂ atmosphere. The spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ was prepared by mixing the precalcined [Ni_1/3Co_1/3Mn_1/3]CO₃ with LiOH followed by high temperature calcination. The preparation conditions such as ammonia concentration, co-precipitation temperature, calcination temperature and Li/[Ni_1/3Co_1/3Mn_1/3] ratio were varied to optimize the physical and electrochemical properties of the prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂. The structural, morphological, and electrochemical properties of the prepared LiNi_1/3Co_1/3Mn_1/3O₂ were characterized by XRD, SEM, and galvanostatic charge-discharge cycling. The optimized material has a spherical particle shape and a well ordered layered structure, and it also has an initial discharge capacity of 162.7 mAh g^− 1 in a voltage range of 2.8-4.3 V and a capacity retention of 94.8% after a hundred cycles. The optimized ammonia concentration, co-precipitation temperature, calcination temperature, and Li/[Ni_1/3Co_1/3Mn_1/3] ratio are 0.3 mol L^− 1, 60 °C, 850 °C, and 1.10, respectively.     

X-ray photoelectron spectroscopy and electrochemical behaviour of 4 V cathode, Li(Ni1/2Mn1/2)O2

Layered Li(Ni_1/2Mn_1/2)O₂ was prepared by the solution and mixed hydroxide methods, characterised by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and studied by cyclic voltammetry (CV) and charge discharge cycling in CC and CCCV modes at room temperature (r.t.) and at 50 °C. The XPS studies show about 8% of Ni³⁺ and Mn³⁺ ions are present in Li(Ni²⁺_1/2Mn_1/2⁴⁺)O₂ due to valency-degeneracy. The compound prepared at 950 °C, 12 h, solution method gives a second cycle discharge capacity of 150 mA h g⁻¹ (2.5-4.4 V) at a specific current of 30 mA g⁻¹ and retains 137 mA h g⁻¹ at the end of 40 cycles. CV shows that the redox process at 3.7-4.0 V corresponds to Ni²⁺↔Ni⁴⁺ and clear indication of Mn^3+/4+ couple was noted at 4.2-4.5 V. The observed capacity-fading (2.5-4.4 V) is shown to be contributed by the polarisation at the end of charging. The cathodic capacity is stable up to 40 cycles in the voltage window, 2.5-4.2 V both at room temperature and 50 °C.     

A delithiated LiNi0.65Co0.25Mn0.10O2 electrode material: A structural, magnetic and electrochemical study

A crystalline LiNi_0.65Co_0.25Mn_0.10O₂ electrode material was synthesized by the combustion method at 900 °C for 1 h. Rietveld refinement shows less than 3% of Li/Ni disorder in the structure. Lithium extraction involves only the Ni²⁺/Ni⁴⁺ redox couple while Co³⁺ and Mn⁴⁺ remain electrochemically inactive. No structural transition was detected during cycling in the whole composition range 0 < x < 1.0. Furthermore, the hexagonal cell volume changes by only 3% when all lithium was removed indicating a good mechanical stability of the studied compound. LiNi_0.65Co_0.25Mn_0.10O₂ has a discharge capacity of 150 mAh/g in the voltage range 2.5-4.5 V, but the best electrochemical performance was obtained with an upper cut-off potential of 4.3 V. Magnetic measurements reveal competing antiferromagnetic and ferromagnetic interactions - varying in strength as a function of lithium content - yielding a low temperature magnetically frustrated state. The evolution of the magnetic properties with lithium content confirms the preferential oxidation of Ni ions compared to Co³⁺ and Mn⁴⁺ during the delithiation process.     

Synthesis and electrochemical properties of Li[Li0.07Ni0.1Co0.6Mn0.23]O2 as a possible cathode material for lithium-ion batteries

The layered Li[Li_0.07Ni_0.1Co_0.6Mn_0.23]O₂ materials were synthesized by sol-gel method with glycine or citric acid as chelating agent. The prepared materials were characterized by means of XRD, SEM and Raman spectroscopy. Li/Li[Li_0.07Ni_0.1Co_0.6Mn_0.23]O₂ cells were assembled and subjected to charge-discharge studies at different C rates, viz 0.2, 1, 2 and 4 C. Although the samples showed less discharge capacity at 4 C rate the fade in capacity per cycle is lesser than that of capacity fade at 0.2 C rate. The citric acid assisted sample is found to be superior in terms of discharge capacity, capacity retention rate and also in thermal stability to that of sample prepared with glycine as chelating agent.