Phase structure and morphology of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Supermolecular structure of isotactic polypropylene/wollastonite/styrenic rubber block copolymers composites were studied as a function of elastomeric poly‐ (styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and the SEBS grafted with maleic anhydride (SEBS‐g‐MA) content (from 0 to 20 vol%) by optical, scanning, and transmission electron microscopy, wide‐angle X‐ray diffraction and differential scanning calorimetry. Wollastonite particles disturbed the spherulitization of polypropylene matrix. Both elastomers affected the crystallization of polypropylene matrix mainly by solidification effect. Although SEBS‐g‐MA encapsulated wollastonite particles more expressive than SEBS forming thus core‐shell morphology in higher extent, scanning electron micrographs indicated more constrained wollastonite particles in fractured surfaces of composites with SEBS elastomer. Moreover, SEBS‐g‐MA disorientated wollastonite particles and affected reorientation of the polypropylene crystallites stronger than SEBS elastomer. POLYM. ENG. SCI., 47:2145–2154, 2007. © 2007 Society of Plastics Engineers     

Microstructural characteristics of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Microstructural characteristics of isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and dynamic mechanical analyses (DMA) showed that the iPP/SEBS and iPP/SEBS‐g‐MA blends were partially compatible two‐phase systems. Well‐dispersed spherical GB and acicular W particles without evidence of interfacial adhesion were observed in the iPP/GB and iPP/W binary composites respectively. Contrary to the blends, melt flow rates of the iPP/GB and PP/W composites decreased more with SEBS‐g‐MA than with SEBS because of enhanced interfacial adhesion with SEBS‐g‐MA elastomer. The SEM analyses showed that the ternary composites containing SEBS exhibited separate dispersion of the rigid filler and elastomer particles (i.e., separate microstructure). However, SEBS‐g‐MA elastomer not only encapsulated the spherical GB and acicular W particles completely with strong interfacial adhesion (i.e., core‐shell microstructure) but also dispersed separately throughout iPP matrix. In accordance with the SEM observations, the DSC and DMA revealed quantitatively that the rigid filler and SEBS particles in iPP matrix acted individually, whereas the rigid filler particles in the ternary composites containing SEBS‐g‐MA acted like elastomer particles because of the thick elastomer interlayer around the filler particles. The Fourier transform infrared analyses revealed an esterification reaction inducing the strong interfacial adhesion between the SEBS‐g‐MA phase and the filler particles. POLYM. COMPOS., 31:1265–1284, 2010. © 2009 Society of Plastics Engineers     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Mechanical properties of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Mechanical properties of the isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, the poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. An increase in toughness of iPP with the elastomers was associated with a decrease in rigidity and strength. Mechanical performance of iPP increased more with acicular W than with spherical GB due to reinforcing effect of W. Comparing the (iPP/GB)/SEBS and (iPP/W)/SEBS composites having the separate microstructure, strength and toughness values of the iPP/GB and iPP/W composites increased more with SEBS‐g‐MA at the expense of rigidity due to the core‐shell microstructure with strong interfacial adhesion. Moreover, the iPP/W composite exhibited superior mechanical performance with 2.5 and 5 vol% of SEBS‐g‐MA because of a positive synergy between the core‐shell microstructure and reinforcing effect of acicular W. The extended models revealed that the elastomer and filler particles in the (iPP/GB)/SEBS and (iPP/W)/SEBS composites acted individually due to the separate microstructure. However, the rigid GB and W particles encapsulated with the thick elastomer interlayer (R₀/R₁ = 0.91) in the (iPP/GB)/SEBS‐g‐MA and (iPP/W)/SEBS‐g‐MA composites acted like neither big elastomer particles nor like individual rigid particles, inferring more complicated failure mechanisms in the core‐shell composites. POLYM. COMPOS., 31:1285–1308, 2010. © 2010 Society of Plastics Engineers     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

Process–structure–property relationship in ternary short‐glass‐fiber/elastomer/polypropylene composites

Short‐glass‐fiber (SGF)‐reinforced polypropylene (PP) composites toughened with a styrene/ethylene butylene/styrene (SEBS) triblock copolymer were injection molded after extrusion. Furthermore, a maleic anhydride (MA)‐grafted SEBS copolymer (SEBS‐g‐MA) was used as an impact modifier and compatibilizer. The effects of the processing conditions and compatibilizer on the microstructure and tensile and impact performance of the hybrid composites were investigated. In the route 1 fabrication process, SGF, PP, and SEBS were blended in an extruder twice, and this was followed by injection molding. In route 2, or the sequential blending process, the elastomer and PP were mixed thoroughly before the addition of SGF. In other words, either PP and SEBS or PP and SEBS‐g‐MA pellets were premixed in an extruder. The produced pellets were then blended with SGF in the extruder, and this was followed by injection molding. The SGF/SEBS‐g‐MA/PP hybrid fabricated by the route 2 process exhibited the highest modulus, yield stress, tensile stress at break, Izod impact energy, and Charpy drop weight impact strength among the composites investigated. This was due to the formation of a homogeneous SEBS elastomeric interlayer at the SGF and matrix interface of the SGF/SEBS‐g‐MA/PP hybrid. This SEBS rubbery layer enhanced the interfacial bonding between SGF and the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The correlations between the processing, microstructure, and properties of the hybrids were investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1384–1392, 2003     

Morphology and mechanical properties of high‐impact polystyrene/elastomer/magnesium hydroxide composites

Ternary composites of high‐impact polystyrene (HIPS), elastomer, and magnesium hydroxide filler encapsulated by polystyrene were prepared to study the relationships between their structure and mechanical properties. Two kinds of morphology were formed. Separation of elastomer and filler was found when a nonpolar poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS) was incorporated. Encapsulation of filler by elastomer was achieved by using the corresponding maleinated SEBS (SEBS‐g‐MA). The mechanical properties of ternary composites were strongly dependent on microstructure. In this study, the composites with separate dispersion structure showed higher elongation, modulus and impact strength than those of encapsulation structure. Impact‐fracture surface observation showed that the toughening mechanism was mainly due to the massive cavitation and extensive matrix yielding. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5184–5190, 2006     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polypropylene/silica micro‐ and nanocomposites modified with poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene)

The effects of different silica loadings and elastomeric content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with 5, 10, 15, and 20 vol % of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) SEBS added to total composite volume were investigated. Four silica fillers differing in size (nano‐ vs. micro‐) and in surface properties (untreated vs. treated) were chosen as fillers. Elastomer SEBS was added as impact modifier and compatibilizer at the same time. The morphology of ternary polymer composites revealed by light and scanning electron microscopies was compared with morphology predicted models based on interfacial properties. The results indicated that general morphology of composite systems was determined primarily by interfacial properties, whereas the spherulitic morphology of polypropylene matrix was a result of two competitive effects: nucleation effect of filler and solidification effect of elastomer. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough SEBS elastomer. Spherulitic morphology of polypropylene matrix might affect some mechanical properties additionally. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41486.     

Toughening and compatibilization of polyphenylene sulfide/nylon 66 blends with SEBS and maleic anhydride grafted SEBS triblock copolymers

In this study, styrene‐b‐ethylene/butylene‐b‐styrene triblock copolymer (SEBS) and maleic anhydride grafted SEBS (SEBS‐g‐MA) were used as compatibilizers for the blends of polyphenylene sulfide/nylon 66 (PPS/PA66). The mechanical properties, including impact and tensile properties and morphology of the blends, were investigated by mechanical properties measurements and scanning electron microscopy. Impact measurements indicated that the impact strength of the blends increases slowly with elastomer (SEBS and SEBS‐g‐MA) content upto 20 wt %; thereafter, it increases sharply with increasing elastomer content. The impact energy of the elastomer‐compatibilized PPS/PA66 blends exceeded that of pure nylon 66, implying that the nylon 66 can be further toughened by the incorporation of brittle PPS minor phase in the presence of SEBS or SEBS‐g‐MA. The compatibilization efficiency of SEBS‐g‐MA for nylon‐rich PPS/PA66 was found to be higher than SEBS due to the in situ forming SEBS interphase between PPS and nylon 66. The correlation between the impact property and morphology of the SEBS‐g‐MA compatibilized PPS/PA66 blends is discussed. The excellent impact strength of the nylon‐rich blends resulted from shield yielding of the matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Tribological behavior of polyamide 66‐based binary and ternary composites

Friction and wear characteristics of polyamide 66 (PA66) and the composites of organoclay modified by styrene–ethylene/butylene–styrene triblock copolymer grafted with 1.84 wt% of maleic anhydride (SEBS‐g‐MA) were studied using an Universal Micro Tribometer reciprocating friction and wear tester. The morphologies of the wear tracks of PA66 and the composites were observed using a scanning electron microscope. The results showed that plastic deformation induced by the traction of the harder steel ball occurred on the worn surfaces of PA66 and the composite which were reinforced by SEBS‐g‐MA copolymer. It was found that the average frictional coefficient and specific wear rate of PA66/SEBS‐g‐MA binary composite are lowest under the same conditions. This indicates that toughness and wear resistance of PA66 matrix are improved with the incorporation of SEBS‐g‐MA copolymer. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Interfacial modification of high impact polystyrene magnesium hydroxide composites effects on flame retardancy properties

High impact polystyrene (HIPS)/magnesium hydroxide (MH) composites were prepared by melt‐blending. Two kinds of interfacial modifiers were used in this research, maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA) triblock copolymer and PS. The effects of the use levels of SEBS‐g‐MA on the flame retardancy of HIPS/elastomer/MH based on unmodified and PS‐modified surface were investigated by TEM, FTIR, and combustion tests (horizontal burning test and cone calorimetry). The combustion results showed that comparing composites containing unmodified MH, the flame retarding properties of composites containing PS‐modified MH were obviously improved. The increased performance can be explained that the PS covered on the surface of MH could further improve dispersion of the filler in matrix. Furthermore, there existed a critical thickness of interfacial boundary for optimum flame‐retarding properties in both ternary composites based MH and PS‐modified MH. When the interfacial boundary relative thickness is less than 0.53, the introduction of SEBS‐g‐MA can improve the dispersion degree, leading the improvement of flame retardancy properties. However, with the increase of interfacial boundary thickness, the SEBS‐g‐MA coating around MH acted as a heat and mass transfer barrier, leading to the reduction of flame retardancy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of transfer film on tribological behavior of polyamide 66‐based binary and ternary nanocomposites

BACKGROUND: In a polymer–metal sliding system, the formation and performance of the transfer film have important effects on the tribological behavior of the polymer. In order to reveal the wear mechanism of polyamide 66 (PA 66) and its composites consisting of styrene–(ethylene/butylene)–styrene triblock rubber grafted with maleic anhydride (SEBS‐g‐MA) particles and organoclay nano‐layers, the tribological behavior and transfer films of polyamide 66 and its composites were investigated under dry sliding. RESULTS: The incorporation of SEBS‐g‐MA rubber particles reduces the wear mass loss of PA 66, while the addition of organoclay nano‐layers increases the wear mass loss. The transfer films formed by neat PA 66 and PA 66/organoclay binary nanocomposite include a dark portion and bright portion. In the dark portion, the transfer film is thicker; in the bright portion, the steel ring surface is exposed. The transfer film formed by PA 66/SEBS‐g‐MA/organoclay ternary nanocomposite is thinner and more uniform than the transfer films formed by the other materials. CONCLUSION: When SEBS‐g‐MA rubber particles and organoclay nano‐layers are added simultaneously to PA 66, the wear resistance of PA 66 can be improved markedly. The main reason is that PA 66/SEBS‐g‐MA/organoclay ternary nanocomposite can form a thin and uniform transfer film on the steel ring surface. Copyright © 2008 Society of Chemical Industry     

Effects of compatibilizers and testing speeds on the mechanical properties of organophilic montmorillonite filled polyamide 6/polypropylene nanocomposites

In the present study, the fracture properties of different types of organophilic montmorillonite (OMMT) filled polyamide 6/polypropylene nanocomposites was investigated. Two types of compatibilizers, i.e., maleic anhydride grafted polypropylene (PP‐g‐MA) and maleic anhydride grafted styrene‐ethylene/butylene‐styrene (SEBS‐g‐MA) were used to compatibilize these systems. The tensile properties were studied through tensile test at two different testing speeds; 50 and 500 mm/min whereas the fracture properties were determined using single‐edge‐notch‐3 point‐bending (SEN‐3PB) specimens at three different testing speeds; 1, 100, and 500 mm/min. The presence of both PP‐g‐MA and SEBS‐g‐MA compatibilizers improved the tensile and fracture properties of nanocomposites due to the compatibilizing effect of both compatibilizers. SEBS‐g‐MA compatibilizer seemed to be more effective in improving the fracture toughness of nanocomposites than PP‐g‐MA especially at high testing speed. This was due to the elastomeric nature of SEBS‐g‐MA, which can provide a better toughening effect than the relatively harder PP‐g‐MA. POLYM. ENG. SCI., 50:1493–1504, 2010. © 2010 Society of Plastics Engineers     

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐ b‐styrene] on dielectric,thermal, and morphological characteristics of polypropylene/silica nanocomposites

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) copolymer on the thermal and dielectric properties of polypropylene (PP)—nanosilica (NS) composites in relation with morphological aspects revealed by atomic force microscopy (AFM) was investigated in this article. SEBS hindered the crystallization process of PP in PP/NS composites, leading to a smaller degree of crystallinity and lower perfection of crystalline structure. Broader lamellar thickness distribution was obtained in nanocomposites containing SEBS. Almost two times higher dielectric loss as compared to PP reference and two relaxation processes were detected in ε_r ^′′(f) curves of nanocomposites. The first peak, in the same frequency domain as for the references, was assigned to α‐relaxation of polymer components together with interfacial polarization. The relaxation time follows the Arrhenius law with an activation energy of 80–90 kJ/mol. For the second process, the temperature dependence of the relaxation times obeyed the VFT equation. The dielectric changes following the incorporation of SEBS support its tendency to hinder the motional processes in PP, in accordance with DSC results. A smooth transition from a phase rich in SEBS to one containing mainly PP was detected in the AFM image of the composite with the larger amount of SEBS, emphasizing the good compatibility at the PP/SEBS interface. POLYM. ENG. SCI., 53:2081–2092, 2013. © 2013 Society of Plastics Engineers     

Thermo‐oxidative decomposition kinetics of elastomeric composites based on styrene‐(ethylene‐butylene)‐styrene triblock copolymer and organomontmorillonite

The elastomeric nanocomposites based on organomontmorillonite (OMMT) and styrene‐(ethylene‐butylene)‐styrene (SEBS) thermoplastic elastomer were prepared by melt processing using maleic anhydride grafted SEBS (SEBS‐g‐MA) as compatibilizer. Thermo‐oxidative decomposition behavior of the neat components and the nanocomposites were investigated using thermogravimertic analysis (TGA) in air atmosphere. The isoconversional method is employed to study the kinetics of thermo‐oxidative degradation. The heating modes and the composition of nanocomposites were found to affect the kinetic parameters (E_a, lnA and n). The E_a and lnA values of SEBS, OMMT, and their composites are much higher under dynamic heating than under isothermal heating. The reaction order (n) of OMMT was lower than those of SEBS and their composites. The obtained TG profiles and calculated kinetic parameters indicated that the incorporation of OMMT into SEBS significantly improved the thermal stability both under dynamic heating and under isothermal heating. The simultaneously obtained DSC data showed that the enthalpy of thermal decomposition decreased with OMMT loading. No significant change in the nonisothermal and isothermal stability of the nanocomposites with addition of SEBS‐g‐MA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Dynamic reaction inside co‐rotating twin screw extruder. I. Truck tire model material/polypropylene blends

Waste ground rubber tire (WGRT) is a complex composite containing various elastomers, carbon black, zinc oxide, stearic acid, processing oils, and other curatives. Most of the waste ground rubber tire is composed of mainly natural rubber (NR) and styrene butadiene rubber (SBR) in varying proportions. Blending it with other thermoplastic materials is difficult due to the inherent thermodynamic incompatibility. But, the compatibility can be increased by making the reactive sites in WGRT with suitable chemicals under optimum condition of shearing inside a twin screw extruder and it is said to undergo a dynamic reaction inside the extruder. To understand the mechanism of dynamic reaction process of a rubber/polyolefin blend, the blending of a truck tire model material rubber with polyolefin was first tried before it was applied to waste WGRT material. It was observed that the blends of a truck tire model rubber material and PP thermoplastic are physical mixture of two incompatible polymers in which a continuous plastic phase is largely responsible for the tensile properties. The rubber particles are the dispersed phase. The large particle size and the poor adhesion of these rubber particles are believed to be liable for the poor tensile properties. In case of blends of truck tire model material with isotactic polypropylene the tensile properties are found to be lower than that of its PP‐g‐MA counterpart which can be attributed to the reaction of the MA with the carbon black particles. A schematic representation of the possible interactions has been proposed. The effect of addition of compatibilizers such as SEBS and SEBS‐g‐MA has also been studied. The tensile and TGA studies indicate that the polarity of SEBS and SEBS‐g‐MA induces an increase in the performance characteristics for both types of polyolefins but the intensity of this increase is higher in the PP‐g‐MA based blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 106: 3193–3208, 2007