Effect of carbon content on electrical,thermal, and mechanical properties of porous SiC ceramics with B4C and C additives

The electrical, thermal, and mechanical properties of porous SiC ceramics with B₄C-C additives were investigated as functions of C content and sintering temperature. The electrical resistivity of porous SiC ceramics decreased with increases in C content and sintering temperature. A minimal electrical resistivity of 4.6 × 10^?2 Ω·cm was obtained in porous SiC ceramics with 1 wt% B₄C and 10 wt% C. The thermal conductivity and flexural strength increased with increasing sintering temperature and showed maxima at 4 wt% C addition when sintered at 2000 °C and 2100 °C. The thermal conductivity and flexural strength of porous SiC ceramics can be tuned independently from the porosity by controlling C content and sintering temperature. Typical electrical resistivity, thermal conductivity, and flexural strength of porous SiC ceramics with 1 wt% B₄C-4 wt% C sintered at 2100 °C were 1.3 × 10^?1 Ω·cm, 76.0 W/(m·K), and 110.3 MPa, respectively.     

Sinterability,microstructure and compressive strength of porous glass-ceramics from metallurgical silicon slag and waste glass

Porous glass-ceramics have been prepared by the direct sintering of powder mixtures of metallurgical silicon slag and waste glass. The thermal behavior of silicon slag was examined by differential thermal analysis and thermogravimetry to clarify the foaming mechanism of porous glass-ceramics. The mass loss of silicon slag below 700 °C was attributed to the oxidation of amorphous carbon from residual metallurgical coke in the silicon slag, and the mass gain above 800 °C to the passive oxidation of silicon carbide. The porosity of sintered glass-ceramics was characterized in terms of the apparent density and pore size. By simply adjusting the content of waste glass and sintering parameters (i.e. temperature, time and heating rate), the apparent density changed from 0.4 g/cm³ to 0.5 g/cm³, and the pore size from 0.7 mm to 1.4 mm. In addition to the existing crystalline phases in the silicon slag, the gehlenite phase appeared in the sintered glass-ceramics. The compressive strength of porous glass-ceramics firstly increased and then decreased with the sintering temperature, reaching a maximal value of 1.8 MPa at 750 °C. The mechanical strength was primarily influenced by the crystallinity of glass-ceramics and the interfaces between the crystalline phases and the glassy matrix. These sintered porous glass-ceramics exhibit superior properties such as light-weight, heat-insulation and sound-absorption, and could found their potential applications in the construction decoration.     

Fabrication of lightweight ZrO2 fiberboards using hollow ZrO2 fibers

ZrO₂ fiberboards with ultra-low densities (0.34–0.40 g/cm³) were fabricated using biomorphic ZrO₂ hollow fibers, which have a lower density and better thermal insulation than traditional ZrO₂ solid fibers. The effects of sol binder content, sintering temperature, and proportion of solid fibers on the density, microstructure, compressive strength, linear shrinkage, and thermal conductivity of lightweight ZrO₂ fiberboards were investigated. The results showed that the hollow features of biomorphic ZrO₂ fibers were successfully maintained after they were made into ZrO₂ fiberboards, which made them less dense and thermally conductive. The best conditions were found to be a sol binder content of 30 vol%, sintering temperature of 1400 °C, and 20 wt% sintered solid fibers to balance thermal insulation and compressive strength. The results show that the density and thermal conductivity of lightweight ZrO₂ fiberboard gives it obvious advantages as a heat-insulating ceramic. Specifically, when the sintering temperature was 1400 °C, the sample had an ultra-low density of 0.34–0.40 g/cm³, a thermal conductivity of 0.101–0.116 W/(m·K) (at 500 °C), a compressive strength of 0.05–0.24 MPa, and a linear shrinkage of 9.4–13%.     

Effects of particle size distribution and sintering temperature on properties of alumina mold material prepared by stereolithography

Alumina mold materials prepared by stereolithography usually have considerable sintering shrinkage, and their properties related to casting have been rarely studied. In this study, alumina molds materials were prepared by stereolithography, and the effects of particle size distribution and sintering temperature on the properties of the materials were investigated. Results show that the viscosity of the slurries decreases as the fraction of fine powder increases, and the particle size distribution affects the curing behaviors slightly. Sintering shrinkage increases as the fraction of fine powder or the sintering temperature increases. Although lower sintering shrinkage can be achieved by sintering at 1350 °C or 1450 °C, the mold materials sintered at lower temperatures would continue to shrink under the service temperature of 1550 °C, and thus 1550 °C is determined as the optimal sintering temperature. As the fraction of fine powder increases, the creep resistance first increases and then decreases, and specimens prepared with 0.1 fraction of fine powder exhibit the best creep resistance with the droop distance of 4.44 ± 0.45 mm. Specimens prepared with 0.1 fraction of fine powder and sintered at 1550 °C exhibit linear shrinkage of 6.36% along the X/Y direction and 11.39% along the Z direction, and have a flexural strength of 78.15 ± 3.50 MPa and porosity of 30.12 ± 0.08%. The resulting material possesses relatively low sintering shrinkage, proper mechanical strength, porosity and high-temperature properties that meet the requirements for casting purposes.     

Preparation study for the low thermal expansion spodumene/mullite composites

In this work, spodumene/mullite ceramics with low thermal expansion were successfully prepared from spodumene, quartz, talc, and clay. The effects of spodumene content and sintering temperature on the mechanical properties of spodumene/mullite ceramics were investigated. The formed phases were then detected by X-ray diffraction analysis and the microstructures of the sintered bodies were determined by scanning electron microscopy. The interaction effects of the spodumene content and sintering temperature on the apparent porosity and bulk density were studied by response surface methodology. The results demonstrate that an appropriate sintering temperature and spodumene content can promote densification, improve the mechanical properties, and reduce the coefficient of thermal expansion (CTE) of spodumene/mullite ceramics. At the spodumene content of 40 wt.%, the sintering temperature of 1270°C, and the holding time of 90 min, the bending strength was 60.45 MPa, the CTE was 1.73 × 10^–6/°C (α_{[25–650°C]} < 2 × 10^–6/°C), the bulk density was 2.28 g cm^-3, and the apparent porosity was 0.43%. Therefore, this study was of guiding significance for reducing the production cost of spodumene low thermal expansion ceramics and improving product quality.     

Reaction-bonded robust SiC ceramic membranes sintered at low temperature with coal gangue

Herein, we report an in-situ reaction-bonded SiC membrane sintered at low temperature using a solid waste (i.e. coal gangue) as the sintering aid to form strong neck connections. The effects of sintering temperature and coal gangue proportion on their properties regarding pore size, open porosity, bending strength and pure water permeability were investigated. The single-channel tubular SiC membrane sintered at 1300 °C with a coal gangue proportion of 12 wt% was optimal, exhibiting an average pore size of 2.78 μm, a open porosity of 47.08%, a bending strength of 34.01 ± 1.3 MPa and a high water permeability of 83967 L m⁻² h⁻¹ bar⁻¹. The membrane could completely reject D₅₀ = 0.87 μm SiC solids and presented a steady-state water permeability of 458 L m⁻² h⁻¹·bar⁻¹. The SiC membrane could be regenerated through ultrasonication and its steady-state water permeability was almost unchanged for 3 cycles, proving its mechanical robustness. This work may appeal to the practical low-cost production of high-performance SiC membranes.     

Thermo-mechanical and high-temperature dielectric properties of cordierite-mullite-alumina ceramics

Heterogeneous ceramics made of cordierite (55–56 wt%), mullite (22–33 wt%) and alumina (23–11 wt%) were prepared by sintering non-standard raw materials containing corundum, talc, α-quartz, K-feldspar, kaolinite and mullite with small amounts of calcite, cristobalite and glass phases. The green specimens prepared by PVA assisted dry-pressing were sintered within the temperature range of 950–1500 °C for different dwelling times (2–8 h). The effects of sintering schedule on crystalline phase assemblage and thermomechanical properties were investigated. The sintered ceramics exhibited low coefficients of thermal expansion (CTE) (3.2–4.2×10⁻⁶ °C⁻¹), high flexural strength (90−120 MPa and high Young modulus (100 GPa). The specimens sintered at 1250 °C exhibited the best thermal shock resistance (∆T~350 °C). The thermal expansion coefficients and thermal shock resistance were studied using Schapery model, the modelling results implying the occurrence of non-negligible mechanical interactions between the phases in bulk. The dielectric properties characterized from room to high temperature (RT– HT, up to 600 °C) revealed: (i) noticeable effects of sintering schedule on dielectric constant (5–10) and dielectric loss factor (~0.02–0.04); (ii) stable dielectric properties until the failure of the electrode material. The thermomechanical properties coupled with desirable dielectric properties make the materials suitable for high density integrated circuitry or high temperature low-dielectric materials engineering.     

Preparation and properties of porous ceramic aggregates using electrical insulators waste

In this paper, porous ceramic aggregates were prepared by electrical insulators waste (EIW). Effects of sintering temperature and content of EIW on the aggregates’ properties such as bulk density, and apparent porosity, total porosity, and cold crushing strength were investigated. With increasing sintering temperature and content of EIW, bulk density and cold crushing strength of the aggregates increased, apparent porosity and total porosity decreased. Based on these results, total porosity of specimens in group B sintered at 1200 °C is 62.0%, cold crushing strength is 35.3 N, and thermal conductivity is 0.165 W/(m K) at 300 °C. Comprehensive properties of specimens can be optimized by adjusting sintering temperature. Meanwhile, strength variation resulted from the combined effects of phase transformation and matrix densification under different sintering temperatures.     

Macro-porous dolomite hollow fibers sintered at different temperatures toward widened applications

Ceramic hollow fibers from natural dolomite with different pore structures have been designed. The unique hollow fibers were produced by the phase inversion method and applying different sintering temperatures. The hollow fiber precursor presented coagulated polymers through the fiber thickness due to the high granulometric size of the used dolomite material (11.3–47.2 µm). The fiber sintered at 400 °C presented mechanical strength of 4.5 MPa and water permeability of 84.7 L h⁻¹ m⁻² kPa⁻¹. The increase in the sintering temperature up to 1250 °C resulted in fragile hollow fibers due to dolomite transformations that resulted in gas release and a significant mass loss of 33.7%. At 1350 °C, the liquid phase sintering mechanism occurred and the dolomite hollow fiber sintered at 1350 °C presented mechanical strength of 5.5 MPa and water permeability of 2219 L h⁻¹ m⁻² kPa⁻¹. Doloma dissolution in water was investigated and calcium concentration was increased from 0.72 (pure water) to 2.905 ppm for a contact time from 4 h between the fiber sintered at 1250 °C and pure water. However, this dissolution did not decrease the mechanical resistance of the fiber. These results suggest the potential of applying natural dolomite for producing low cost membranes or substrates. The hollow fiber sintered at 400 °C is suggested to be used as a proper separation medium, while the hollow fiber sintered at 1350 °C may be used as a substrate for the deposition of a separation layer to be used in gas separations. The high porosity of the fiber sintered at 1250 °C suggests its application as a support for the impregnation of functional materials. Thus, depending on the applied sintering temperature the dolomite membrane can be used in different applications.     

Preparation of ZnO-glass composite hollow fiber and its application in formation of ZIF-8 membrane

The sintering temperature of ZnO ceramic hollow fibers (HFs) is generally up to 1400°C and presents a major challenge to obtain HFs with high permeability and mechanical strength at lower sintering temperature. This work proposed a glass powder-assisted method to reduce the sintering temperature by using their adhesive property. ZnO-glass composite HFs with longer finger-like channels, high permeability (3.12 × 10⁻⁵–9.1 × 10⁻⁶ mol·m⁻²·s⁻¹·Pa⁻¹) and good mechanical strength (42.12–52.75 MPa) were obtained at sintering temperature of 1150°C. More glass powders can generate stronger bonding effect during the ZnO particles, resulting in a decrease in porosity and an increase in the mechanical strength of ZnO-HF. These ZnO-HFs were further applied for inducing ZIF-8 membranes by one-step solvothermal growth. ZnO not only provides the growth and nucleation centers but also acts as transitional bridge to make the ZIF embed into support to improve the bonding force between membrane and support. Therefore, HF-supported-ZIF-8 membrane exhibited both mechanical and thermal robustness by maintaining their gas separation performance during the 30-min sonication treatment and 50-h operation testing at 25–200°C. Furthermore, this membrane provided good reproducibility. This work opens prospects for preparing ceramic HFs at lower sintering temperature and their functional applications as well as the preparation of MOF membranes.     

A Novel Way to Prepare Hollow Sphere Ceramics

Recent developments in the fabrication of hollow spheres have allowed our group to prepare a new type of macroporous ceramics: hollow sphere ceramics (HSCs). Alumina hollow spheres were first produced by centrifugal spray‐drying of particle‐stabilized foam slurry. The obtained hollow spheres were sintered together to form HSC at high temperatures. The effect of the sintering temperature on the linear shrinkage, porosity and compressive strength of HSC samples was investigated. When the sintering temperature was increased from 1400°C to 1600°C, the samples shrunk increasingly and the porosity decreased from 59% to 42%, which lead to an increase in the strength of the alumina foams from 6.9 (at 1400°C) to 100.0 MPa (at 1550°C). The mechanical strength of the HSC highly depends on the contact area between the hollow spheres, which could be increased by increasing the sintering temperature, decreasing the size of hollow spheres or by slurry infiltration.     

High-strength AlN ceramics by low-temperature sintering with CaZrO3–Y2O3 co-additives

Aluminum nitride (AlN) ceramics with the concurrent addition of CaZrO₃ and Y₂O₃ were sintered at 1450-1700 °C. The degree of densification, microstructure, flexural strength, and thermal conductivity of the resulting ceramics were evaluated with respect to their composition and sintering temperature. Specimens prepared using both additives could be sintered to almost full density at relatively low temperature (3 h at 1550 °C under nitrogen at ambient pressure); grain growth was suppressed by grain-boundary pinning, and high flexural strength over 630 MPa could be obtained. With two-step sintering process, the morphology of second phase was changed from interconnected structure to isolated structure; this two-step process limited grain growth and increased thermal conductivity. The highest thermal conductivity (156 Wm⁻¹ K⁻¹) was achieved by two-step sintering, and the ceramic showed moderate flexural strength (560 MPa).     

Effect of sintering temperature on microstructure and mechanical properties of zirconia-toughened alumina machinable dental ceramics

This study investigated the effect of sintering temperature on the microstructure and mechanical properties of dental zirconia-toughened alumina (ZTA) machinable ceramics. Six groups of gelcast ZTA ceramic samples sintered at temperatures between 1100 °C and 1450 °C were prepared. The microstructure was investigated by mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and scanning electron microscopy (SEM) techniques. The mechanical properties were characterized by flexural strength, fracture toughness, Vickers hardness, and machinability. Overall, with increasing temperature, the relative density, flexural strength, fracture toughness, and Vickers hardness values increased and more tetragonal ZrO₂ transformed into monoclinic ZrO₂; on the other hand, the porosity and pore size decreased. Significantly lower brittleness indexes were observed in groups sintered below 1300 °C, and the lowest values were observed at 1200 °C. The highest flexural strength and fracture toughness of ceramics reached 348.27 MPa and 5.23 MPa m^1/2 when sintered at 1450 °C, respectively. By considering the various properties of gelcast ZTA that varied with the sintering temperature, the optimal temperature for excellent machinability was determined to be approximately 1200–1250 °C, and in this range, a low brittleness index and moderate strength of 0.74–1.19 µm^−1/2 and 46.89–120.15 MPa, respectively, were realized.     

Fabrication and characterization of bone china using synthetic bone powder as raw materials

The synthetic bone powder was studied as a raw materials for bone china, completely replacing natural bone ash raw materials. The physical and thermal properties of samples obtained by the two bone powders were tested and comparatively studied. Performance tests included pyroplastic deformation, flexural strength, bulk density, sintering shrinkage, water absorption, transmittance, thermal expansion coefficient and the thermal shock resistance. The phase composition and morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results indicated that using synthetic bone powder could shorten the preparation time, reduce the sintering temperature and result in high-quality bone china. The pyroplastic deformation decreased from 9.14% to 7.92%, the three-point flexural strength increased from 123 MPa to 191 MPa, the light transmittance (at a 2-mm thickness) increased from 6.7% to 11.2%, the thermal expansion coefficient decreased from 8.24×10⁻⁶ °C⁻¹ to 7.69×10⁻⁶ °C⁻¹, and the thermal shock resistance increased from 140 °C to 180 °C. A continuous interface layer without cracks was produced by using the synthetic bone powder.     

An eco-friendly permeable brick with excellent permeability and high strength derived from steel slag wastes

Utilisation of industrial solid wastes to prepare products with high added value is an effective way that could relieve environmental pollution and create huge economic benefits. In this work, steel slag based permeable brick (SSPB) was successfully prepared by liquid phase sintering. The BSE-EDS results indicate that the microstructure of the SSPB becomes dense because of the formation of a small amount of glass-liquid phase (Na-K-Ca-Fe-Si-O glass system). The effect of sintering temperature on various properties of the SSPB was systematically studied. It is found that as the sintering temperature increases from 1210 to 1300°C, the permeability deceases gradually, as well as the apparent porosity, water retention and water absorption. In contrast, the bulk density and mechanical strengths show gradually increasing trends. Most important of all, the SSPB sintered at 1270°C for 1 hour shows an excellent permeability (5.70 × 10⁻² cm/s) and high mechanical strengths (compressive strength, 36.6 MPa; bending strength, 6.8 MPa). The prepared SSPB is not only likely to be a new type of permeable brick for sidewalk construction, but also relieve greatly environmental pollution from steel slag because of the high utilisation rate of steel slag (as high as 90%).     

Microstructural evolution and sintering properties of palygorskite nanofibers

In this study, the morphological evolution and sintering properties of the palygorskite nanofibers were studied along with the increase of temperature, using raw palygorskite as materials. The palygorskite powder was calcined at different temperatures in the range of 100°C-1200°C, and the microstructural evolution of the palygorskite nanofibers was investigated by thermogravimetric and differential thermal analysis (TG-DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscope (HRTEM). Furthermore, the palygorskite powder was shaped to bars by dry pressing and sintered from 700°C to 1200°C. The properties of the sintered palygorskite were characterized by bending strength, mercury intrusion porosimeter (MIP), and stepwise isothermal dilatometry (SID). The results showed that the morphology of palygorskite nanofibers maintained unchanged till 1000°C. The palygorskite nanofibers molted to bind each other and formed a solid interwoven network structure at 1100°C. Correspondingly, it was shown from the sharply decrease of the sintered palygorskite porosity from 45.46% at 1000°C to 1.82% at 1100°C that the dense sintering of palygorskite started at 1100°C. With the sintering proceeding, some closed micropores fused each other to form bigger opening pores, resulting in a slight increase of porosity at 1200°C. However, the pore size distribution got more uniform and the density of the sintered body increased. So the bending strength of the sintered body reached the maximum of 176.67 Mpa and finally the main crystalline phases of the sintered sample changed to quartz, enstatite, and kyanite. The sintering activation energy of the palygorskite was measured by means of SID with a value of 906.46 kJ·mol⁻¹.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.     

Electrically conductive SiC ceramics processed by pressureless sintering

Polycrystalline SiC ceramics with 10 vol% Y₂O₃-AlN additives were sintered without any applied pressure at temperatures of 1900-2050°C in nitrogen. The electrical resistivity of the resulting SiC ceramics decreased from 6.5 × 10¹ to 1.9 × 10⁻² Ω·cm as the sintering temperature increased from 1900 to 2050°C. The average grain size increased from 0.68 to 2.34 μm with increase in sintering temperature. A decrease in the electrical resistivity with increasing sintering temperature was attributed to the grain-growth-induced N-doping in the SiC grains, which is supported by the enhanced carrier density. The electrical conductivity of the SiC ceramic sintered at 2050°C was ~53 Ω⁻¹·cm⁻¹ at room temperature. This ceramic achieved the highest electrical conductivity among pressureless liquid-phase sintered SiC ceramics.     

Preparation and performance study of cordierite/mullite composite ceramics for solar thermal energy storage

The employment of solar energy in recent years has reached a remarkable edge. It has become even more popular as the cost of fossil fuel continues to rise. Energy storage system improves an adjustability and marketability of solar thermal and allowing it to produce electricity in demand. This study attempted to prepare cordierite/mullite composite ceramics used as solar thermal storage material from calcined bauxite, talcum, soda feldspar, potassium feldspar, quartz, and mullite. The thermal physical performances were evaluated and characterized by XRD, SEM, EPMA, and EDS. It was found that the optimum sintering temperature was 1280°C for preparing, and the corresponding water adsorption was 11.25%, apparent porosity was 23.59%, bulk density was 2.10 mg·cm^?3, bending strength was 88.52 MPa. The residual bending strength of specimen sintered at 1280°C after thermal shock of 30 times decreased to be 57 MPa that was 36% lower than that before. The thermal conductivity of samples sintered at 1280°C was tested to be 2.20 W·(m·K)^?1 (26°C), and after wrapped a PCM (phase change materials) of K₂SO₄, the thermal storage density was 933 kJ·kg^?1 with the temperature difference (ΔT) ranged in 0‐800°C. The prepared cordierite/mullite composite ceramic was proved to be a promising material for solar thermal energy storage.     

Facile preparation of thermal insulation materials by microwave sintering of ferronickel slag and fly ash cenosphere

A novel approach for preparing thermal insulation materials by microwave sintering of ferronickel slag (FNS) in the presence of fly ash cenosphere (FAC) was proposed and evaluated. The study showed that during microwave radiation, the contact interface between FNS and FAC would preferentially form magnesium iron chromate spinel and magnesium iron aluminate spinel particles as hot spots by absorbing microwave vigorously, promoting decomposition and transformation of the raw materials into the thermal insulation phases, mainly cordierite and enstatite. After sintering at 900 °C by microwave for only 20 min with the addition of 25 wt% FAC, a thermal insulation material with thermal conductivity of 0.41 W/(m·K), bulk density of 1.46 g/cm³, compressive strength of 30.72 MPa, water absorption of 21.07%, and linear shrinkage of 7.06% was obtained. Compared with the conventional sintering method, the temperature was reduced by 300 °C, with the sintering time shortened by 6 times. This study represents a good example for clean and efficient value-added utilization of FNS, FAC and other relavent solid wastes.