Synthesis,characterization and thermal degradation of poly[2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate]

In this work, 2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate (BPHEMA) [monomer] was synthesized by the addition of methacrylic acid to 1‐epoxyethyl‐3‐bromophenyl‐3‐methyl cyclobutane. The monomer and poly(BPHEMA) were characterized by FT‐IR and [¹H] and [¹³C]NMR. Average molecular weight, glass transition temperature, solubility parameter, and density of the polymer were also determined. Thermal degradation of poly[BPHEMA] was studied by thermogravimetry (TG), FT‐IR. Programmed heating was carried out at 10 °C min⁻¹ from room temperature to 500 °C. The partially degraded polymer was examined by FT‐IR spectroscopy. The degradation products were identified by using FT‐IR, [¹H] and [¹³C]NMR and GC‐MS techniques. Depolymerization is the main reaction in thermal degradation of the polymer up to about 300 °C. Percentage of the monomer in CRF (Cold Ring Fraction) was estimated at 33% in the peak area of the GC curve. Intramolecular cyclization and cyclic anhydride type structures were observed at temperatures above 300 °C. The liquid products of the degradation, formation of anhydride ring structures and mechanism of degradation are discussed. © 1999 Society of Chemical Industry     

Semiconductive poly[N1,N4‐bis(thiophen‐2‐ylmethylene)benzene‐1,4‐diamine]‐nickel oxide nanocomposite based ethanol sensor

This study aims to use the conductivity of a synthetic polymer as the sensing probe for ethanol. In order to enhance the sensitivity of the sensor, a composite of the polymer and nickel oxide (NiO) nanoparticles was formed as it improved the conductivity. This composite exhibited 100 times more conductivity than the neat polymer. The semiconductive nanocomposite of poly [N¹,N⁴‐bis(thiophen‐2‐ylmethylene)benzene‐1,4‐diamine]‐nickel oxide (PBTMBDA‐NiO) was prepared by in situ chemical oxidative polymerization. The monomer was N¹,N⁴‐bis(thiophen‐2‐ylmethylene)benzene‐1,4‐diamine (BTMBDA). The monomer (BTMBDA), polymer (PBTMBDA), and NiO nanoparticles used in this study were synthesized. The monomer was prepared by refluxing together 2‐thiophene carboxaldehyde, benzene‐1,4‐diamine, and few drops of glacial acetic acid in ethanol medium for 3 h. The polymer, PBTMBDA, was formed by the chemical oxidative polymerization of BTMBDA in chloroform by FeCl₃. NiO nanoparticles were prepared by slow addition of aqueous ammonia to anhydrous nickel chloride at room temperature (28 ± 2 °C), and at a pH of 8 under constant stirring condition. The composite was formed by in situ chemical oxidative polymerization of BTMBDA in chloroform by FeCl₃ in the presence of the dispersed NiO nanoparticles. The molecular structure of BTMBDA and PBTMBDA were confirmed by nuclear magnetic resonance (NMR) (¹H, ¹³C, and Dept‐90°), Fourier transform infrared spectroscopy, and ultraviolet (UV)–visible spectroscopy. The PBTMBDA and PBTMBDA‐NiO nanocomposite were characterized by X‐ray diffraction, thermogravimetric analysis, field emission scanning electron microscopy, and energy‐dispersive X‐ray spectroscopy analysis. The results of characterization studies indicate the strong interaction between PBTMBDA and NiO in the nanocomposite. The broadness of ¹H NMR peaks in PBTMBDA was due to the increased number of monomer units. The disappearance of the peak of α‐hydrogens on thiophene confirms the polymerization involving the fifth position of thiophene part of BTMBDA. The Fourier transform infrared spectroscopy spectra revealed that position of the characteristic peaks of the functional groups in the monomer shifted toward lower wave numbers in PBTMBDA and PBTMBDA‐NiO nanocomposite. This shifting confirms the presence of extended conjugation along the polymer backbone. Electronic spectra of these compounds showed three absorption bands corresponding to π→π*, n→π* and n→π* transitions of π electron of carbon, lone pair electrons of S, and lone pair electrons of N (imine) groups, respectively. From the Tafel plot, the exchange current density evaluated for the BTMBDA and PBTMBDA are 0.2815 × 10⁻⁸ and 1.1508 × 10⁻⁸ A cm⁻², respectively. PBTMBDA is evaluated to be a better electrode material than the BTMBDA. The X‐ray diffraction plots showed that the characteristic peak of NiO in PBTMBDA‐NiO nanocomposite suggested successful incorporation of NiO in PBTMBDA‐NiO nanocomposite. The thermogravimetric analysis revealed the improved thermal stability of the composite. Field emission scanning electron microscopy and energy‐dispersive X‐ray spectroscopy analysis confirmed the presence of the NiO in the composite. Incorporation of nickel oxide nanoparticles improved the electrical conductivity and stability of PBTMBDA. The conductivity of the polymer was found to be of the order of 10⁻⁵ S cm⁻¹ while that of the composite was of the order of 10⁻³ S cm⁻¹. The nanocomposite was found to be thermally more stable than PBTMBDA and exhibited better direct‐current electrical conductivity and isothermal stability than the PBTMBDA as revealed by the four‐probe study. The electrical conductivity as inferred from the four‐probe method was used as the parameter to study the isothermal stability of the composite. The PBTMBDA‐NiO nanocomposite based vapor sensor was constructed for the sensing of ethanol vapor in commercial ethanol and real samples (alcoholic drinks: Beer, Wine, Brandy, Vodka, Whisky, and Rum) It was observed that on exposure to ethanol vapor at ambient temperature, the electrical resistivity of the nanocomposite increased indicating suppression of charge carriers. The interaction of ethanol vapor with PBTMBDA in PBTMBDA‐NiO nanocomposite was confirmed by IR spectral technique. The change in the structure of the PBTMBDA on interaction with ethanol was highlighted by the changes in the infrared spectrum. The conductivity of the polymer was explained using the structure‐activity relationship of the monomer evaluated using Gaussian 09 software. This study also analyzed the total electron density with electrostatic potential of the monomer and its correlation with chemical reactivity in order to explain the ethanol vapor sensing‐property of the nanocomposite. A new method of ethanol vapor sensing by a conducting polymer composite is hereby reported. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45918.     

m‐Chloroaniline emulsion polymerization,macromolecular chain structure and electrochemical properties

Poly(m‐chloroaniline) (PmClAn) was synthesized by emulsion polymerization. The influences of reaction temperature and initiator concentration on polymerizations were studied. It was found that PmClAn with number‐average molecular weight of 1.85 × 10³ g mol^?1 was obtained by the following conditions: 80 °C, [monomer] = 0.187 × 10^?3 mol l^?1, [sodium lauryl sulfate] = 4.8 × 10^?2 mol l^?1, [potassium peroxydisulfate] = 5.6 × 10^?2 mol l^?1, reaction period = 2.0 h. ¹H NMR, FTIR, and transmission and scanning microscopy were used for structural characterization of PmClAn. It was shown that the ratio of benzoid to quinoid units in the macromolecular chain was respectively 3:2, and that PmClAn has a typical crystalline monoclinic form. A PmClAn molecular chain configuration was also proposed on the basis of crystallographic data. Cyclic voltammetry experiments revealed the PmClAn membrane electrode electroactivity. This electroactivity increased when the polymer was proton‐doped. When Pt particles were electrodeposited onto the polymer membrane electrode, they presented a preferred orientation. Isopropanol oxidation intensities with platinized PmClAn modified electrodes were larger than with a platinized Pt electrode. We also found that oxidation occurred mainly on the Pt particles deposited on the polymer, and that the anodic peak potential changed with polymer and its doping level. These results indicated that the Pt particles interacted with the polymer and that catalytic properties could be observed. © 2002 Society of Chemical Industry     

Poly(2‐allyl)phenylene‐oxide electropolymer film growth on steel

The variation of film structure and properties with growth conditions was examined for poly(2‐allyl)phenylene‐oxide films grown electrochemically on a mild steel substrate from a basic hydro‐alcoholic monomer solution, to establish the best conditions for the production of thin, continuous, adherent films. The use of sodium hydroxide as the base led to the production of discontinuous, irregular films (upon drying). Substitution of allylamine as the base produced continuous, regular films, initially gel‐like, but becoming hard and glassy upon drying or thermal treatment. Film thickness increased substantially as the pH was raised from 9.0 to 11.0, with substrate corrosion decreasing over the same range. Platinum was used as a comparable noncorroding substrate. Film thickness also increased with monomer concentration, but current flow minimized at a monomer concentration of 0.25M. Double bond functionality was retained through the polymerization process, but lost upon heat curing of the polymer films. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1563–1571, 2001     

Synthesis and characterization of the soluble fluorescent poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)‐1,4‐phenylenevinylene]

A new soluble fluorescent polymer, poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyl‐oxy)naphthyl)‐1,4‐phenylenevinylene] (DDN‐PPV), with no tolane‐bisbenzyl (TBB) structure defects is prepared by the dehydrohalogenation of 1,4‐bis(bromomethyl)‐2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)benzene (as monomer) in this study. The aforementioned monomer is synthesized via such chemical reactions as alkylation, bromination, and Suzuki coupling reactions. The structure and properties of the DDN‐PPV are examined by ¹H NMR, FTIR, UV/vis, TGA, photoluminescence (PL), and electroluminescence (EL) analyses. The two asymmetric decyloxy and 6′‐dodecyloxynaphthyl substituents on the phenylene ring make the DDN‐PPV soluble in organic solvents and eliminate the TBB structure defects. With the DDN‐PPV acting as a light‐emitting polymer, a device is fabricated with a sequential lamination of ITO/PEDOT/DDN‐PPV/Ca/Ag. The EL spectrum of the device shows a maximum emission at 538 nm. The turn on voltage of the device is about 16.6 V. Its maximum brightness is 14 cd/m² at a voltage of 18.2 V. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2734–2741, 2007     

Chelation properties of poly(2‐hydroxy‐4‐acryloyloxybenzophenone) resins toward some divalent metal ions

The chelation behavior of poly(2‐hydroxy‐4‐acryloyloxybenzophenone) [poly(2H4ABP) or polymer I ] obtained through the free‐radical polymerization of 2‐hydroxy‐4‐acryloyloxybenzophenone monomer and for crosslinked polymers prepared from the monomer and known amounts of the crosslinker divinylbenzene (DVB) [4 mol % of DVB for polymer II, 8 mol % of DVB for polymer III, and 16 mol 16% of DVB for polymer IV ] toward the divalent metal ions Cu²⁺, Ni²⁺, Zn²⁺, and Pb²⁺ in aqueous solution was studied by a batch equilibration technique as a function of contact time and pH. The effect of the crosslinker, DVB, was also studied. The metal‐ion uptake of the polymers was determined with atomic absorption spectroscopy, and the highest uptake was achieved at pH 7.0 for polymers I, II, III, and IV. The selectivity and binding capacity of the resins toward the investigated divalent metal ions are discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Using hydroxypropyl‐β‐cyclodextrin for the preparation of hydrophobic poly(ketoethyl methacrylate) in aqueous medium

This work was committed to the polymerization of hydrophobic ketoethyl methacrylate monomer in aqueous medium in the presence of cyclodextrin, instead of polymerizing the monomer in toxic and volatile organic solvents. For this purpose, a new ketoethyl methacrylate monomer, p‐methylphenacylmethacrylate (MPMA), was synthesized from the reaction of p‐methylphenacylbromide with sodium methacrylate in the presence of triethylbenzylammonium chloride. The monomer was identified with FTIR, ¹H and ¹³C‐NMR spectroscopies. Hydroxypropyl‐β‐cyclodextrin (HPCD) was used to form a water‐soluble host/guest inclusion complex (MPMA/HPCD) with the hydrophobic monomer. The complex was identified with FTIR and NMR techniques and polymerized in aqueous medium using potassium persulfate as initiator. During polymerization the resulting hydrophobic methacrylate polymer precipitated out with a majority of HPCD left in solution and a minority of HPCD bonded on the resulting polymer. The thus‐prepared polymer exhibited little difference from the counterparts obtained in organic solvent in number average molecular weight (M_n), polydispersity (M_w/M_n) and yield. The investigation provides a novel strategy for preparing hydrophobic ketoethyl methacrylate polymer in aqueous medium by using a monomer/HPCD inclusion complex. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Nonionic water‐soluble polymer: Preparation,characterization, and application of poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) as a polychelatogen

The free‐radical copolymerization of water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) was carried out with a feed monomer ratio of 75:25 mol %, and the total monomer concentration was 2.67M. The synthesis of the copolymer was carried out in dioxane at 70°C with benzoyl peroxide as the initiator. The copolymer composition was obtained with elemental analysis and ¹H‐NMR spectroscopy. The water‐soluble polymer was characterized with elemental analysis, Fourier transform infrared, ¹H‐ and ¹³C‐NMR spectroscopy, and thermal analysis. Additionally, viscosimetric measurements of the copolymer were performed. The thermal behavior of the copolymer and its complexes were investigated with differential scanning calorimetry (DSC) and thermogravimetry techniques under a nitrogen atmosphere. The copolymer showed high thermal stability and a glass transition in the DSC curves. The separation of various metal ions by the water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) reagent in the aqueous phase with liquid‐phase polymer‐based retention was investigated. The method was based on the retention of inorganic ions by this polymer in a membrane filtration cell and subsequent separation of low‐molar‐mass species from the polymer/metal‐ion complex formed. Poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) could bind metal ions such as Cr(III), Co(II), Zn(II), Ni(II), Cu(II), Cd(II), and Fe(III) in aqueous solutions at pHs 3, 5, and 7. The retention percentage for all the metal ions in the polymer was increased at pH 7, at which the maximum retention capacity could be observed. The interaction of inorganic ions with the hydrophilic polymer was determined as a function of the pH and filtration factor. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 178–185, 2006     

Synthesis of 2‐(9H‐carbazole‐9‐yl)ethyl methacrylate: Electrochemical impedance spectroscopic study of poly(2‐(9H‐carbazole‐9‐yl)ethyl methacrylate) on carbon fiber

In this contribution, 2‐(9H‐carbazol‐9‐yl) ethyl methacrylate (CzEMA) monomer was chemically synthesized. The monomer characterization was performed by FT‐IR, ¹H‐NMR, ¹³C‐NMR, and melting point analysis. The electropolymerization of CzEMA was studied onto carbon fiber microelectrodes (CFMEs) as an active electrode material in 0.1M sodium perchlorate (NaClO₄)/acetonitrile (ACN) solution. The electropolymerization experiments were done from 1 mM to 10 mM. The detailed characterization of the resulting electrocoated Poly (CzEMA)/CFME thin films was studied by various techniques, i.e., cyclic voltammetry (CV), Scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The effects of initial monomer concentrations (1, 3, 5, and 10 mM) during the preparation of modified electrodes were examined by EIS. Capacitive behaviors of modified CFMEs were defined via Nyquist, Bode‐magnitude, and Bode‐phase plots. Variation of capacitance values by initial monomer concentration and specific capacitance values are presented. The highest specific capacitance value electrocoated polymer thin film by CV method in the initial monomer concentration of 5 mM with a charge of 52.74 mC was obtained about 424.1 μF cm^?2. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of 2‐oxazoline‐benzoxazine compound and its polymer

A novel 2‐oxazoline‐benzoxazine (POB) was synthesized with 2‐(hydroxylphenyl)‐2‐oxazoline, 1,3,5‐triphenylhexahydro‐1,3,5‐triazine and paraformaldehyde. The chemical structure of the monomer was confirmed by FTIR, ¹H‐NMR, ¹³C‐NMR, and MS. The curing behavior of the monomer was studied by DSC and FTIR, and the ring opening reaction of the monomer was found to occur from 187.5°C. The results of DMA and TGA demonstrated that the thermal properties of polymer for POB monomer (P‐m) are better than polymer for POB precursor (P‐p), because that the oligomer in benzoxazine precursor decreased the perfection of the polymer's network structure; it was also found that the thermal properties of P‐m and P‐p are much better than the common polybenzoxazine and the composite material of benzoxazine and 2‐oxazoline. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci , 2008.     

Synthesis and characterization of new polyureas derived from 4‐(4′‐Methoxyphenyl)urazole

4‐(4′‐Methoxyphenyl)urazole (MPU) was prepared from 4‐methoxybenzoic acid in five steps. The reaction of monomer MPU with n‐isopropylisocyanate was performed at room temperature in N,N‐dimethylformamide solution, and the resulting bis‐urea derivative was obtained in high yield and was finally used as a model for polymerization reaction. The step‐growth polymerization reactions of monomer MPU with hexamethylene diioscyanate, isophorone diioscyanate, and toluene‐2,4‐diioscyanate were performed in N,N‐dimethylacetamide solution in the presence of pyridine as a catalyst. The resulting novel polyureas have an inherent viscosity (η_inh) in a range of 0.07–0.21 dL/g in DMF and sulfuric acid at 25°C. These polyureas were characterized by IR, ¹H‐NMR, elemental analysis, and TGA. Some physical properties and structural characterization of these novel polyureas are reported. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1141–1146, 2002     

Synthesis and properties of polymer from bis‐3,4‐ethylenedioxythiophene substituted acenaphthenequinoxaline

A new electrochoromic polymer poly(8,11‐bis(3,4‐ethylenedioxy thiophen‐2‐yl)acenaphtho[1,2‐b]‐quinoxaline) (PBEAQ) was synthesized by electrochemical polymerization of the corresponding monomer (BEAQ) in a 0.1 M tetraethylammonium tetrafluoroborate (TEABF₄) dichloromethane–acetonitrile (2 : 1, v : v) solution. The monomer and polymer were characterized by elemental analysis, ¹H‐NMR, IR, and UV‐vis spectroscopy. The electrochemical and optical properties of polymer were investigated by cyclic voltammetry and UV‐vis spectroscopy. Cyclic voltammetry and spectroelectrochemistry studies demonstrated that the polymer can be reversibly reduced and oxidized (both n‐ and p‐doped) between ?2 V and +1.5 V vs. Ag/Ag⁺. The polymer had a transmissive light blue color in the oxidized state and reddish color in the reduced state. Undoped polymer shows UV‐vis absorption peaks at 615 nm in solution, 650 nm in solid state, and has an optical band gap of 1.5 eV. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of conducting copolymer of Trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene with EDOT

Ferrocene‐substituted conducting polymer namely poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene‐co‐3,4‐ethylenedioxythiophene) [P(MTFE‐co‐EDOT)] was synthesized and its electrochromic properties were studied. Monomer, MTFE, was obtained using 2‐(ferrocenyl)ethene and 3‐methyl‐4‐bromothiophene. The structure of monomer was determined via Fourier transform infrared spectroscopy (FTIR), ¹H‐NMR, and ¹³C‐NMR techniques. The copolymer was synthesized using this monomer and EDOT. The resulting copolymer P(MTFE‐co‐EDOT) was characterized by cyclic voltammetry, FTIR, scanning electron microscopy, atomic force microscopy, and UV–vis spectroscopy. The conductivity measurements of copolymer and PEDOT were accomplished by the four‐probe technique. Although poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene) [P(MTFE)] reveals no electrochromic activity, its copolymer with EDOT has two different colors (violet and gray). Band gap (E_g) and λ_max of P(MTFE‐co‐EDOT) were determined. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Low Risk Synthesis of Energetic Poly(3‐Azidomethyl‐3‐Methyl Oxetane) from Tosylated Precursors

Azidated oxetanic polymers such as poly(3‐azidomethyl‐3‐methyl oxetane), are under investigation as “energetic” binder to be used as an alternative to polybutadiene in solid rocket propellants. The classic synthetic route for the production of the polymer is through an azidated monomer where the N₃⁻ functionality has been previously introduced by nucleophilic displacement of a suitable, usually a halogen, leaving group. However, this could involve critical steps with manipulation of a highly unstable liquid monomer. Here it is shown that the azidation can be performed as the final step of the preparation by substitution of the tosyl group in a preformed polymer. The procedure assures good yield and purity of the product and satisfactory rate of reaction, being the energetic functionality always kept in a safe form, which shows low shock and friction sensitivity. Poly(3‐azidomethyl‐3‐methyl oxetane) was prepared by azidation of poly(3‐tosyloxymethyl‐3‐methyl oxetane) in dimethylsulfoxide, testing several operating conditions. Moreover, hypothesizing a second order kinetics, the rate constant and the activation energy for the azidation step have been estimated.     

Grafting of sulfonated monomer onto an amino‐silane functionalized 2‐aminoterephthalate metal − organic framework via surface‐initiated redox polymerization: proton‐conducting solid electrolytes

A post‐polymerization method for metal–organic frameworks (MOFs) has been developed to produce super‐acidic solid nanoparticles. Thus, the NH₂MIL‐53(Al) MOF was functionalized with (3‐aminopropyl)triethoxysilane (APTES) from amine groups to yield active site anchored MOF nanoparticles. Then, sulfonated polymer/MOF hybrid nanoparticles were prepared by redox polymerization of 2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid (MOF‐g‐PAMPS), initiated onto the surfaces of aminopropyl‐functionalized NH₂MIL‐53(Al) nanoparticles. The synthesis and modification of NH₂MIL‐53(Al) nanoparticles were characterized by Fourier transform infrared (FTIR) spectroscopy and TGA. FTIR and TGA results indicated that APTES modifier agent and AMPS monomer were successfully grafted onto the MOF nanoparticles. The grafting efficiency of PAMPS polymer onto the MOF nanoparticles was estimated from TGA thermograms to be 33%. Also, sulfonated polymer/MOF hybrid nanoparticles showed a proton conductivity as high as 4.9 × 10^?5 S cm^?1. Nitrogen adsorption of modified NH₂MIL‐53(Al) showed also a decrease in pore volume. The morphology and crystalline structure of MOF nanoparticles before and after the modification processes were studied by SEM and XRD, respectively. © 2015 Society of Chemical Industry     

Proton Conducting Membranes Based on Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole)

Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole) (PBI‐imi) was synthesized via the polycondensation between 3,3′,4,4′‐tetraaminobiphenyl and 4,5‐imidazole‐dicarboxylic acid. Effects of the reaction conditions on the intrinsic viscosity of the synthesized polymers were studied. The results show that the molecular weight of the polymers increases with increasing monomer concentration and reaction time, and then levels off. With higher reaction temperature, the molecular weight of the polymer is higher. With the additional imidazole group in the backbone, PBI‐imi shows improved phosphoric acid doping ability, as well as a little higher proton conductivity when compared with widely used poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] (PBI‐ph).Whereas, PBI‐imi and PBI‐ph have the similar chemical oxidation stability. PBI‐imi/3.0 H₃PO₄ composite membranes exhibit a proton conductivity as high as 10^–4 S cm^–1 at 150 °C under anhydrous condition. The temperature dependence of proton conductivity of acid doped PBI‐imi can be modeled by an Arrhenius equation.     

Microwave assisted polycondensation of polyimides by [4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,pyromellitic dianhydride] and [2,4,6‐trimethyl‐m‐phenylenediamine]. Power,time, and solvent effect

The microwave assisted polycondensation of two polyimides were studied using pyromellitic dianhydride (PMDA), and 4,4′‐(hexafluoroisopropyliden)diphthalic anhydride (6FDA) as dianhydride monomers and 2,4,6‐trimethyl‐m‐phenylenediamine (TrmPD), as diamine monomer, under microwave irradiation in DMF and DMSO solvents. The structure and performance of polymers were characterized by Fourier Transform Infrared Spectroscopy (FTIR), viscosity, density, and Thermogravimetric Analysis (TGA). The results show that the polyimides can be obtained in a short reaction time with high intrinsic viscosity and high yield. The effect of the presence of a bridging group, ? C(CF₃)₂? , in the monomer structure is apparent in the permeability parameters of the macromolecules as polymer (6FDA‐TrmPD) always presents better results than polymer (PMDA‐TrmPD). Properties as density and T_g increases with the time exposition to the microwave irradiation. Polyimides obtained present good thermal properties because they began to lose weight in a range of 8–16% at high temperature as 450°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Functionalization of crosslinked polyacrylamide through γ‐radiation‐induced grafting of 4‐vinylpyridine

Crosslinked polyacrylamide beads were irradiated in air with a Co⁶⁰ γ‐radiation source. The preirradiated beads were graft‐copolymerized through heating with 4‐vinylpyridine in the presence of benzoyl peroxide. Grafting was studied as a function of various reaction parameters and was determined from the increase in the weight of the original polymer and the estimation of pyridine pendants in the homopolymer‐free graft copolymer. Although making the polymer basic in character, this modification retained the hydrophilic nature of polyacrylamide. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2613–2620, 2002     

Copolyesters of hydroxyphenylalkanoic acids: synthesis and thermal properties of poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} and poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]}

Copolyesters of 8‐(3‐hydroxyphenyl)octanoic acid (HPOA), a monomer with kink and flexible segment derived from cardanol, and 4‐hydroxybenzoic acid (HBA) or its brominated derivative, 3‐bromo‐4‐hydroxybenzoic acid (BrHBA), were synthesized by acidolysis melt polycondensation of the in situ generated acetoxyderivative in the presence of magnesium acetate as catalyst by a one‐pot method and characterized. The formation of the copolyester was confirmed by elemental analysis, FTIR and ¹H NMR spectroscopy. These polymers were highly insoluble in most solvents except highly polar solvents, such as trifluoroacetic acid. The inherent viscosities of the soluble polymers were in the range of 0.8–1.1 dlg^?1. The thermal and phase behaviour of the copolyesters were studied by DSC and polarized light microscopy. Poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} with 50 mole% of HPOA showed a birefringent melt with opalescence and a worm‐like texture of a nematic phase. The effect of bromine substitution in the analogue poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} was evident when it showed a lower transition with minimum 45% Br‐HBA at 225 °C showing enhanced melt processability. These copolymers, with hydrolytically degradable aliphatic carbonyl group and better crystallinity compared to poly(hydroxyalkanoate)s, are interesting in possible biomedical applications. © 2002 Society of Chemical Industry     

Polymerization of 1,3‐dienes containing functional groups: 8. Free‐radical polymerization of 2‐triethoxysilyl‐ 1,3‐butadiene

The presence of a bulky substituent at the 2‐position of 1,3‐butadiene derivatives is known to affect the polymerization behavior and microstructure of the resulting polymers. Free‐radical polymerization of 2‐triethoxysilyl‐1,3‐butadiene ( 1 ) was carried out under various conditions, and its polymerization behavior was compared with that of 2‐triethoxymethyl‐ and other silyl‐substituted butadienes. A sticky polymer of high 1,4‐structure ( ) was obtained in moderate yield by 2,2′‐azobisisobutyronitrile (AIBN)‐initiated polymerization. A smaller amount of Diels–Alder dimer was formed compared with the case of other silyl‐substituted butadienes. The rate of polymerization (R_p) was found to be R_p = k[AIBN]^0.5[ 1 ]^1.2, and the overall activation energy for polymerization was determined to be 117 kJ mol^?1. The monomer reactivity ratios in copolymerization with styrene were r ₁ = 2.65 and r_st = 0.26. The glass transition temperature of the polymer of 1 was found to be ?78 °C. Free‐radical polymerization of 1 proceeded smoothly to give the corresponding 1,4‐polydiene. The 1,4‐E content of the polymer was less compared with that of poly(2‐triethoxymethyl‐1,3‐butadiene) and poly(2‐triisopropoxysilyl‐1,3‐butadiene) prepared under similar conditions. Copyright © 2010 Society of Chemical Industry