Enhancement on ultimate tensile properties of ultrahigh molecular weight polyethylene composite fibers filled with activated nanocarbon particles with varying specific surface areas

This investigation aims to improve the ultradrawing and ultimate tensile properties of ultrahigh molecular weight polyethylene (UHMWPE) fibers by incorporating small amounts of functionalized activated nanocarbon particles with a wide range of specific surface areas (ca. 100–1,400 m²/g) during gel spinning processes of UHMWPE fibers. The ultradrawing, ultimate tensile, orientation properties, and “microfibril” characteristics of UHMWPE/functionalized activated nanocarbon fibers was discovered to improve considerably with the increase in specific surface areas of functionalized activated nanocarbon. An extraordinary high ultimate tensile strength at 95.8 g/d was obtained for the best prepared UHMWPE/functionalized activated nanocarbon drawn fiber. This value is the highest value ever reported for one‐stage drawn UHMWPE fibers and is about 2.9 times that of the UHMWPE drawn fiber prepared in this study. In addition to thermal, ultimate tensile, and orientation factor properties of as‐prepared and/or drawn UHMWPE/functionalized activated nanocarbon fibers, specific surface area, Fourier transform infrared, and morphological analyses of original and functionalized activated nanocarbons were performed to comprehend the considerably improved ultradrawing, ultimate tensile properties, and microfibril characteristics of the UHMWPE/functionalized activated nanocarbon fibers. POLYM. ENG. SCI., 58:980–990, 2018. © 2017 Society of Plastics Engineers     

Ultradrawing properties of ultrahigh‐ molecular‐weight polyethylene/carbon nanotube fibers prepared at various formation temperatures

The influence of formation temperature on the ultradrawing properties of ultrahigh‐molecular‐weight polyethylene/carbon nanotube (UHMWPE/CNT) fiber specimens is investigated. Gel solutions of UHMWPE/CNT with various CNT contents were gel‐spun at the optimum concentration and temperature but were cooled at varying formation temperatures in order to improve the ultradrawing and tensile properties of the UHMWPE/CNT composite fibers. The achievable draw ratio (D_ra) values of UHMWPE/CNT as‐prepared fibers reach a maximum when they are prepared with the optimum CNT content and formation temperature. The D_ra value of UHMWPE/CNT as‐prepared fibers produced using the optimum CNT content and formation temperature is about 33% higher than that of UHMWPE as‐prepared fibers produced using the optimum concentration and formation temperature. The percentage crystallinity (W_c) and melting temperature (T_m) of UHMWPE/CNT as‐prepared fiber specimens increase significantly as the formation temperature increases. In contrast, W_c increases but T_m decreases significantly as the CNT content increases. Dynamic mechanical analysis of UHMWPE and UHMWPE/CNT fiber specimens exhibits particularly high α‐transition and low β‐transition, wherein the peak temperatures of α‐transition and β‐transition increase dramatically as the formation temperature increases and/or CNT content decreases. In order to understand these interesting drawing, thermal and dynamic mechanical properties of the UHMWPE and UHMWPE/CNT as‐prepared fiber specimens, birefringence, morphological and tensile studies of as‐prepared and drawn fibers were carried out. Possible mechanisms accounting for these interesting properties are proposed. Copyright © 2010 Society of Chemical Industry     

Multiple-step drawing innovative ultrahigh-molecular-weight polyethylene fibers modified with bacterial cellulose and scCO2-aid

Innovative supercritical carbon dioxide (scCO₂)-assisted ultrahigh-molecular-weight-polyethylene (UHMWPE)/modified bacterial cellulose (MBC) as-spun fibers were found to display substantially lower dynamic transition temperatures than those acquired for scCO₂-assisted UHMWPE or UHMWPE/MBC as-spun fibers prepared without scCO₂-assistance or incorporation of MBC nanofibers. Multiple-step drawing methods were first-time applied to these finely ''relaxed'' scCO₂-assisted UHMWPE/MBC fibers and considerably improved their achievable draw ratios (D_ras), orientation factor (f_os), and tensile tenacities (σ_tts). The best five-step drawn scCO₂UHMWPE/MBC fiber displayed a particularly high σ_tt of 135 g d⁻¹, which was ~35, ~3.75, and ~1.7 fold of σ_tts acquired for good steel fiber and the most appropriate single-step drawn scCO₂-assisted UHMWPE and UHMWPE/MBC fibers, respectively. The particularly high D_ras, f_o, and σ_tts acquired for the best multiple-step drawn scCO₂-assisted UHMWPE/MBC fibers is ascribed to their more ''relaxed'' UHMWPE structures, thinner lamellae, and successive increased drawing temperature in the multiple-step drawing processes.     

Ultradrawing properties of ultra‐high molecular weight polyethylene/functionalized carbon nanotube fibers

Systemic investigation of the influence of the plain and functionalized carbon nanotube (CNT) contents on the ultradrawing properties of ultrahigh molecular weight polyethylene/carbon nanotubes (UHMWPE/CNTs, FC_y) and UHMWPE/functionalized CNTs (FC_fx‐y) as‐prepared fibers are reported. In a way similar to those found for the orientation factor values, the achievable draw ratios (D_ra) of the FC_y and FC_fx‐y as‐prepared fibers approached a maximum value as their CNT and/or functionalized CNT contents reached their corresponding optimum values. The maximum D_ra values obtained for FC_fx‐0.001 as‐prepared fiber specimens prepared at varying maleic anhydride grafted polyethylene (PE_‐g‐MAH)/modified CNTs weight ratios were significantly higher that of the FC_0.0015 as‐prepared fiber specimen prepared at the optimum plain CNT content. Tensile property analysis further suggested that excellent orientation and tensile properties of the drawn FC_y and FC_fx‐y fibers can be obtained by ultradrawing the fibers prepared at their optimum plain CNT and/or functionalized CNT contents. To understand the interesting orientation, ultradrawing and tensile properties of FC_y and FC_fx‐y fiber specimens, FTIR, specific surface area, and SEM morphology analysis of the plain and functionalized CNTs were performed in this study. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Ultrahigh molecular weight polyethylene fibers prepared using conical dies with varying dimensions

Dimensions of conical dies were found to have a significant influence on thermal, morphological, orientation, ultradrawing, and dynamic mechanical properties of the as‐prepared and/or drawn ultrahigh molecular weight polyethylene (UHMWPE) fiber specimens prepared in this study. Many demarcated “micro‐fibrils” were found paralleling to fiber direction of the as‐prepared UHMWPE fiber specimens. The percentage crystallinity, melting temperatures, orientation factor (f_o) and achievable draw ratio (D_ra) values of each as‐prepared UHMWPE fiber specimen prepared at a fixed length of outlet land reach a maximum value, as the entry angles of the conical die approach the optimum value at 75°. The maximum f_o and D_ra values obtained for each F₂₀^75‐y as‐prepared fiber series specimens prepared using the optimum entry angle reach another maximum value as their length of outlet land approach the optimum value of 6.5 mm. The ultimate tensile strengths and moduli of the drawn UHMWPE fibers prepared at the optimum entry angle and length of outlet land are significantly higher than those of fibers prepared at other conditions but stretched to the same draw ratio. Possible reasons accounting for the above interesting properties were discussed in this study. POLYM. ENG. SCI., 2013. © 2013 Society of Plastics Engineers     

Ultradrawing properties of ultrahigh‐molecular‐weight polyethylene/attapulgite fibers

An investigation of the influence of the contents of original and modified attapulgite (ATP) on the ultradrawing properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE)/ATP (FA_x) and UHMWPE/modified ATP (FA_mx) as‐prepared fibers is reported. Similar to what is found for the orientation factor values, the achievable draw ratios (D_ra) of the FA_x and FA_mx as‐prepared fibers approach a maximum value as the original ATP and/or modified ATP contents reach their corresponding optimum values. The maximum D_ra value obtained for FA_mx as‐prepared fiber specimens is significantly higher than that for FA_x as‐prepared fiber specimens prepared at the optimum original ATP content. Similar to what is found for the orientation factors and achievable drawing properties, the tensile strength (σ_f) and initial modulus (E) of both drawn F₂A_x and F₂A_mx fiber series specimens with a fixed draw ratio reach maximum values as the original and/or modified ATP contents approach the optimum values, respectively. The σ_f and E values of the F₂A_mx fiber specimens are always significantly higher than those of the corresponding F₂A_x fiber specimens prepared at the same draw ratios and ATP contents but without being modified. To understand the interesting ultradrawing, orientation and tensile properties of FA_x and FA_mx fiber specimens, Fourier transform infrared spectral, specific surface area, transmission electron microscopic and elemental analyses of the original and modified ATPs were performed. Copyright © 2012 Society of Chemical Industry     

Ultradrawing properties of ultrahigh‐molecular weight polyethylene/functionalized carbon nanotube fibers and transmittance properties of their gel solutions

The influences of the dispersion level of carbon nanotubes (CNTs) and functionalized CNTs on the transmittance properties of ultrahigh‐molecular weight polyethylene (UHMWPE) gel solutions and on ultradrawing properties of their as‐prepared fibers are reported. The transmittance properties suggest that the dispersion level of functionalized CNTs in UHMWPE/functionalized CNTs gel solution is significantly better than plain CNTs in UHMWPE/CNTs gel solutions. The orientation factors, achievable draw ratios, tensile strength (σ_f), and modulus (E) values of UHMWPE/CNTs (F_xC_y) and UHMWPE/functionalized CNTs (F_xC_f‐y) as‐prepared fiber specimens reached a maximum value as their CNT and functionalized CNT contents approached optimum contents at 0.00015 and 0.0001 wt%, respectively. The σ_f and E values of both F_xC_0.0012 and F_xC_f‐0.001 series fiber specimens prepared at their optimum CNT and functionalized CNT contents reached another maximum as their UHMWPE approached optimum UHMWPE concentration of 1.7 wt%. Possible reasons accounting for these interesting properties are proposed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Ultradrawing and ultimate tensile properties of ultrahigh molecular weight polyethylene composite fibers filled with functionalized nanoalumina fillers

Ultradrawing and ultimate tensile properties of ultrahigh molecular weight polyethylene (UHMWPE) composite fibers were successfully improved by the addition of nanoalumina (NAL), acid treated nanoalumina (ATNAL), and/or functionalized nanoalumina (FNAL). As evidenced by FTIR and TEM analyses, maleic anhydride grafted polyethylene (PE_g‐MAH) molecules were successfully grafted onto ATNAL fillers. The specific surface areas of FNAL fillers reached a maximal value at 516 m²/g, as they were modified using an optimal weight ratio of PE_g‐MAH to ATNAL at 8. Achievable draw ratio (D_ra) values of UHMWPE/NAL (F₁₀₀A_y), UHMWPE/ATNAL (F₁₀₀A_x%‐8‐y) and/or UHMWPE/FNAL (F₁₀₀A_x%‐8FPE^z_y) as‐prepared fibers approached a maximal value as NAL, ATNAL, and/or FNAL contents reached an optimal value at 0.1, 0.1, and 0.075 phr, respectively. The maximal D_ra values of F₁₀₀A_x%‐8FPE^z_0.075 as‐prepared fiber specimens were significantly higher than those of F₁₀₀A_0.1 and F₁₀₀A_x%‐8‐0.1 as‐prepared fiber specimens. In which, the maximal D_ra values obtained for F₁₀₀A_x%‐8FPE^z_0.075 as‐prepared fibers reached another maximal value as FNAL fillers were modified using an optimal weight ratio of PE_g‐MAH to ATNAL at 8. The ultimate tensile strength value of F₁₀₀A_2%‐8FPE⁸_0.075 drawn fiber reached 6.4 GPa, which was about 2.4 times of that of the UHMWPE drawn fibers prepared at the same optimal UHMWPE concentration and drawing condition. POLYM. ENG. SCI., 55:2205–2214, 2015. © 2015 Society of Plastics Engineers     

Effects of tension on mesomorphic transitions and mechanical properties of oriented poly(ethylene terephthalate) fibers under supercritical CO2 exposure

Samples of partially oriented yarn PET fibers were uniaxially drawn below the glass transition temperature (cold-drawing) before exposure to supercritical carbon dioxide (scCO₂) in the absence and presence of tension at a temperature of 80 °C and a pressure of 220 bar. The effects of draw ratio, scCO₂ exposure, and tension on structural changes and on mechanical properties in particular were investigated using differential scanning calorimetry, tensile deformation, and birefringence and density measurements. A good correlation was obtained among the results obtained from various techniques. Results indicate that exposure to scCO₂ not only induces structural changes but also develops crystallization in the samples. Tension under scCO₂ exposure also produces significant effects in terms of causing structural changes and transforming the oriented chains in the mesophase into the crystalline or noncrystalline domains. PET fibers exposed to scCO₂ under no tension yields lower values of crystallinity, orientation, tenacity, and Young’s modulus but higher values of breaking elongation compared to samples exposed under tension. This is an indication of higher plasticity of the chains in the amorphous domains in samples exposed under no tension. It is also found that mechanical measurements confirm the structural changes taking place in exposed PET samples.     

Drawing in high pressure CO2—a new route to high performance fibers in memory of late Roger Porter

In this paper, we introduce a new draw technique for polymer orientation and apply it to different polymer fibers: poly(ethylene terephthalate) or PET, nylon 6,6, and ultra‐high molecular polyethylene (UHMWPE). In this technique, a polymer is drawn uniaxially in supercritical CO₂ using a custom high‐pressure apparatus. This technique can be used in replacement of a traditional drawing process or as a post‐treatment process. With PET, the technique is not effective at temperatures at or below 130°. In contrast, the process is highly effective for nylon 6,6 where CO₂ drawn fibers show significantly higher crystallinity and orientation along with improved mechanical properties. While the fibers are plasticized, the drawability of the fibers is only slightly dependent on temperature. High pressure CO₂ drawing of ultrahigh molecular weight polyethylene (UHMWPE) fibers is equally effective. Commercial high performance fibers can be drawn up to a ratio of 1.9 in asecond stage, resulting in large increases in tensile modulus and small improvements in tensile strength.     

Preparation and characterization of novel ultra‐high molecular weight polyethylene composite fibers filled with nanosilica particles

Ultrahigh molecular weight polyethylene (UHMWPE)/nanosilica (F₂S_y) and UHMWPE/modified nanosilica (F₂S_mx‐y) as‐prepared fibers were prepared by spinning of F₂S_y and F₂S_mx‐y gel solutions, respectively. Modified nanosilica particles were prepared by grafting maleic anhydride grafted polyethylenes onto nanosilica particles. The achievable draw ratios (D_ra) of F₂S_y and F₂S_mx‐y as‐prepared fibers approached a maximal value as the original and modified nanosilica contents reached corresponding optimum values; the maximal D_ra value obtained for F₂S_mx‐y as‐prepared fiber specimens was significantly higher than that of the F₂S_y as‐prepared fiber specimens prepared at the optimum nanosilica content. The melting temperature and evaluated lamellar thickness values of F₂S_y and F₂S_mx‐y as‐prepared fiber series specimens decrease, but crystallinity values increase significantly, as their original and modified nanosilica contents respectively increase. Similar to the achievable drawing properties of the as‐prepared fibers, the orientation factor, tensile strength (σ_f) and initial modulus (E) values of both drawn F₂S_y and F₂S_mx‐y fiber series specimens with a fixed draw ratio reach a maximal value as the original and/or modified nanosilica contents approach the optimum values; the σ_f and E values of the drawn F₂S_mx‐y fiber specimens are significantly higher than those of the corresponding drawn F₂S_y fiber specimens prepared at the same draw ratios and nanosilica contents but without being modified. To understand the interesting ultradrawing, thermal, orientation and tensile properties of F₂S_y and F₂S_mx‐y fiber specimens, Fourier transform infrared, specific surface area and transmission electron microscopy analyses of the original and modified nanosilica were performed in this study. © 2012 Society of Chemical Industry     

Morphology and structure changes of aromatic copolysulfonamide fibers heat‐drawn at various temperatures

Pre‐drawn aromatic copolysulfonamide (co‐PSA) fibers were prepared by wet spinning and then heat drawing at temperatures varying from 350 to 390 °C, which are below the decomposition temperature. The fibers were then characterized using tensile testing, dynamic mechanical analysis, wide‐angle X‐ray diffraction and small‐angle X‐ray scattering. The relationship between structure and properties of the co‐PSA fibers drawn at different temperatures was investigated. The heat‐drawn co‐PSA fibers displayed similar glass transition temperature of about 355 °C, which was higher than that of pre‐drawn co‐PSA fibers of 345 °C. The crystal orientation was high as a crystalline structure formed during heat drawing and the crystallinity increased with the heat‐drawing temperature. However, the tenacity of the co‐PSA fibers did not increase linearly with the draw temperature. When the drawing temperature was higher than the glass transition temperature, a decrease in tenacity was observed, which could be attributed to an increase of crystallite size of the (100) plane and a decrease of the long period of the lamellar structure. © 2014 Society of Chemical Industry     

Effect of the ultradrawing behavior of gel films of ultrahigh‐molecular‐weight polyethylene and low‐molecular‐weight polyethylene blends on their physical properties

This study examined the effect of the ultradrawing behavior of gel film specimens of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and UHMWPE/low‐molecular‐weight polyethylene (LMWPE) blends on their physical properties. The concentration of a gel film approximated its critical concentration at a fixed drawing temperature; its achievable draw ratio was higher than that of other blend specimens with various concentrations. Noticeably, when about 5 wt % LMWPE was added to a UHMWPE/LMWPE gel film specimen, the achievable draw ratio of the gel film increased, and this contributed to an apparent promoting effect on its anticreeping properties and thermal stability. Therefore, when UL_B?0.9 was drawn to a draw ratio of 300, the anticreeping behavior was improved to less than 0.026%/day. Moreover, with respect to the thermal stability, when the same specimen was drawn to a draw ratio of 300, the retention capability of its storage modulus could resist a high temperature of 150°C, which was obviously much higher than the temperature of an undrawn gel film specimen (70°C). To study these interesting behaviors further, this study systematically investigated the gel solution viscosities, anticreeping properties, dynamic mechanical properties, thermal properties, molecular orientations, and mechanical properties of undrawn and drawn UHMWPE/LMWPE gel film specimens. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Properties of bamboo flour/high-density polyethylene composites reinforced with ultrahigh molecular weight polyethylene

In order to improve the properties of bamboo-plastic composites (BPCs), bamboo flour/high-density polyethylene (HDPE) composites were reinforced with ultrahigh molecular weight polyethylene (UHMWPE). The effects of UHMWPE on properties of composites were studied. The crystallinity of composites decreased slightly. Compared with non-UHMWPE added bamboo powder/HDPE composite, the composite with 6 wt % UHMWPE, showed decrease in water absorption to 0.41%, whereas its tensile strength and flexural strength increased to 34.51 and 25.88 MPa, respectively, a corresponding increase of 34.59 and 12.87%. The temperatures corresponding to initial degradation temperature (T_initial) and maximum degradation temperature (T_max) of the composite increased from 282.7 and 467.4 °C to 288.5 and 474.7 °C respectively. Scanning electron microscopic images showed that UHMWPE was well dispersed and fully extended as long fibers in the composite, forming a “three-dimensional physically cross-linked network structure,” which contributed to the improved properties of the composites. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48971.     

Simultaneously enhanced mechanical properties and thermal properties of ultrahigh‐molecular‐weight polyethylene with polydopamine‐coated α‐alumina platelets

Polydopamine (PDA) was employed to modify micrometric Al₂O₃ platelets to improve the interfacial compatibility between α‐Al₂O₃ powder and ultrahigh‐molecular‐weight polyethylene (UHMWPE). The structure of PDA‐coated Al₂O₃ and UHMWPE composites was investigated via Fourier transform infrared spectroscopy, scanning electron microscopy and X‐ray photoelectron spectroscopy. The thermal stability and mechanical performance of the samples were also evaluated. It is clear that UHMWPE/PDA‐Al₂O₃ composites exhibit better mechanical properties, higher thermal stability and higher thermal conductivity than UHMWPE/Al₂O₃ composites, owing to the good dispersion of Al₂O₃ powder in the UHMWPE matrix and the strong interfacial force between the macromolecules and the inorganic filler caused by the presence of PDA. The tensile strength and the tensile elongation at break of UHMWPE/PDA‐Al₂O₃ composite with 1 wt% PDA‐Al₂O₃ are 62.508 MPa and 462%, which are 1.96 and 1.98 times higher than those of pure UHMWPE, respectively. The thermal conductivity of UHMWPE/PDA‐Al₂O₃ composite increases from 0.38 to 0.52 W m^?1 K^?1 with an increase in the dosage of PDA‐Al₂O₃ to 20 wt%. The results show that the prepared PDA‐coated Al₂O₃ powder can simultaneously enhance the mechanical properties and thermal conductivity of UHMWPE. © 2018 Society of Chemical Industry     

Investigation of the ultradrawing properties of gel spun fibers of ultra‐high molecular weight polyethylene/carbon nanotube blends

The carbon nanotubes (CNTs) contents, ultrahigh‐molecular‐weight polyethylene (UHMWPE) concentrations and temperatures of UHMWPE, and CNTs added gel solutions exhibited significant influence on their rheological and spinning properties and the drawability of the corresponding UHMWPE/CNTs as‐prepared fibers. Tremendously high shear viscosities (ηs) of UHMWPE gel solutions were found as the temperatures reached 140°C, at which their ηs values approached the maximum. After adding CNTs, the ηs values of UHMWPE/CNTs gel solutions increase significantly and reach a maximum value as the CNTs contents increase up to a specific value. At each spinning temperature, the achievable draw ratios obtained for UHMWPE as‐prepared fibers prepared near the optimum concentration are significantly higher than those of UHMWPE as‐prepared fibers prepared at other concentrations. After addition of CNTs, the achievable draw ratios of UHMWPE/CNTs as‐prepared fibers prepared near the optimum concentration improve consistently and reach a maximum value as their CNTs contents increase up to an optimum value. To understand these interesting drawing properties of the UHMWPE and UHMWPE/CNTs as‐prepared fibers, the birefringence, thermal, morphological, and tensile properties of the as‐prepared and drawn fibers were investigated. Possible mechanisms accounting for these interesting properties are proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Ultrahigh molecular weight polyethylene/polypropylene/organo‐montmorillonite nanocomposites: Phase morphology,rheological, and mechanical properties

Phase morphology, rheological, and mechanical properties of ultrahigh molecular weight polyethylene (UHMWPE)/PP/organo‐montmorillonite nanocomposites were investigated in this work. The results of TEM and XRD indicated that the organo‐montmorillonite PMM prepared with the complex intercalator [2‐methacryloyloxyethyldodecyldimethylammonium bromide/poly(ethylene glycol)] were exfoliated and dispersed into UHMWPE matrix, and the synergistic effect of the complex intercalator on the exfoliation and intercalation for montmorillonite occurred. Besides, the presence of PMM in UHMWPE matrix was found able to lead to a significant reduction of melt viscosity and enhancement in tensile strength and elongation at break of UHMWPE, except that izod‐notched impact strength was without much obvious change. The dispersed PMM particles exhibited a comparatively large two‐dimensional aspect ratio (L_clay/d_clay = 35.5), which played an important role in determining the enhancement of mechanical properties of UHMWPE nanocomposites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Structural evaluation and mechanical property of boron nitride fibers during melt‐drawn fabrication process

Boron nitride (BN) fibers were fabricated on a large scale through the melt‐drawn technique from low‐cost boric acid, NH₃, and N₂. Evolution of structure and properties of BN fibers during the fabrication process was studied by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), scanning electron microscope (SEM), and X‐ray photoelectron spectroscopy (XPS). The mechanical properties of BN fibers were tested and analyzed. The results shown that both the mechanical properties and the crystallinity of BN fibers slightly increased with the temperature from 450 to 850°C, due to the combination of the fused‐B₃N₃. For BN fibers heat‐treated at 850 or 1000°C, the tensile strength (σ^R) and elastic modulus (E) were strongly increased because of the increase in crystallization of the BN phase. The meso‐hexagonal BN fibers with a diameter of 5.0 μm were fabricated at 1750°C, of which the tensile strength (σ^R) and elastic modulus (E) are 1200 MPa and 85 GPa, respectively. BN fibers with excellent mechanical properties and proper diameters were obtained by nitriding of green fibers during their conversion into ceramic.     

Influence of Drawing Conditions on the Ultradrawing Properties of Film Specimens of Ultrahigh Molecular Weight Polyethylene and Low Molecular Weight Polyethylene Blends

The influence of the drawing temperature and rate on the ultradrawing properties and deformation mechanisms of a series of film specimens prepared from varying concentrations of gel solutions of ultrahigh molecular weight polyethylene (UHMWPE) and low molecular weight polyethylene (LMWPE) blends is reported. The maximum achievable draw ratio was obtained when each UHMWPE/LMWPE film specimen was drawn at an optimum temperature (T _op), wherein the T _op values of each UHMWPE/LMWPE film specimen increased consistently with the drawing rate. The temperature dependence of the apparent elongational viscosity (_a) revealed two distinguishable intervals with different activation energies. Coincidentally, the transition temperature (T _r) obtained from the intersection of the two straight lines drawn parallel to the two distinct intervals is approximately equal to the T _op value found for the film sample drawn at the same rate. Dynamic mechanical analysis of the film samples exhibited an extraordinary high transition peaked at temperatures near 95–115C, which are again very close to the T _op and T _r values found for the film samples drawn at varying rates, and increases significantly with the testing frequencies. Possible mechanisms accounting for these interesting deformations, temperature dependence of the apparent elongational viscosity and dynamic mechanical properties are suggested in this study.     

Influence of interchain forces and supermolecular structure on the drawing behavior of nylon 66 fibers in the presence of supercritical carbon dioxide

The drawing behavior and mechanical properties of as‐spun and highly oriented nylon 66 fibers drawn in supercritical carbon dioxide (SCCO₂) were investigated. Conditions including different temperatures, CO₂ pressures, and plasticizers with different polarity were systematically studied. Results indicate that CO₂ is an efficient plasticizer for as‐spun nylon 66 fibers as shown by decreases in the draw stress. In contrast, CO₂ shows only a slight influence on the drawability of highly oriented nylon 66 fiber. The effect of other plasticizers such as water, methanol, and ethanol on the drawability of nylon 66 fibers is very similar to that of CO₂. Tenacity and modulus of one‐stage drawn fibers were less than 0.8 and 5.0 GPa, respectively. Fibers with the highest tenacity and modulus, 0.96/5.04 and 1.06/5.04 GPa, were obtained by two‐stage drawing in SCCO₂ from as‐spun and drawn nylon 66 fibers, respectively. The main reason for the extremely low draw ratios (<6.0) of nylon 66 fibers was the presence of hydrogen bonds in the crystalline phase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2282–2288, 2004