电熔增材制造16MND5钢的低周疲劳特性

电熔增材是一种新型重型金属3D打印技术,使用该技术制造的16MND5钢是一种新型材料,对其低周疲劳特性进行系统研究,对推动该技术在核电压力容器上的应用具有重要的指导意义。对电熔增材制造16MND5钢进行了低周疲劳试验研究,试验温度为室温和350℃,采用轴向总应变控制方式,应变比R=-1,应变范围±0.2%～±0.8%。对试验数据进行拟合计算,获得电熔增材制造16MND5钢的应力-应变曲线、应变-寿命曲线和低周疲劳设计曲线等。采用扫描电子显微镜对疲劳试样断口进行了观察,结果显示电熔增材16MND5钢的低周疲劳断口存在多个裂纹源,裂纹扩展区为一系列相互平等的疲劳条带,扩展区同时存在着蠕变孔洞和二次小裂纹,最终断裂区属于韧性断裂。     

Q345R钢湿硫化氢预腐蚀低周疲劳行为

对Q345R钢在湿硫化氢环境中预腐蚀低周疲劳性能进行了研究,以硫化氢溶液的浓度和预腐蚀时间为环境因素.低周疲劳试验在MTS-809疲劳试验机上进行,对各试验组的结果数据进行回归分析,得到各试验组环境下Q345R钢的循环应力-应变曲线、应变-寿命曲线等低周疲劳特性.不同试验环境下的预腐蚀低周疲劳结果表明,材料循环应力应变响应特性不受环境因素影响,为循环硬化特性;预腐蚀时间因素对材料低周疲劳寿命的影响比硫化氢溶液的浓度因素显著.试样断口为典型的低周疲劳断裂形貌,裂纹扩展阶段为脆性准解理断裂特征.     

电熔增材制造16MND5钢的低周疲劳特性

摘要：电熔增材是一种新型重型金属3D打印技术,使用该技术制造的16MND5钢是一种新型材料,对其低周疲劳特性进行系统研究,对推动该技术在核电压力容器上的应用具有重要的指导意义。对电熔增材制造16MND5钢进行了低周疲劳试验研究,试验温度为室温和350℃,采用轴向总应变控制方式,应变比R=-1,应变范围±0.2%～±0.8%。对试验数据进行拟合计算,获得电熔增材制造16MND5钢的应力 应变曲线、应变-寿命曲线和低周疲劳设计曲线等。采用扫描电子显微镜对疲劳试样断口进行了观察,结果显示电熔增材16MND5钢的低周疲劳断口存在多个裂纹源,裂纹扩展区为一系列相互平等的疲劳条带,扩展区同时存在着蠕变孔洞和二次小裂纹,最终断裂区属于韧性断裂。     

HRB400 Ⅲ级抗震钢筋的低周疲劳性能

对HRB400 Ⅲ级抗震钢筋的低周疲劳性能进行了研究。采用轴向应变控制方法,在岛津电液伺服疲劳试验机上测定了试验钢低周疲劳过程中的循环应力响应特征及循环应力与应变的关系;通过拟合Basquin公式和Coffin-Manson公式,获得了试验钢的低周疲劳寿命预测公式。断口扫描发现,试验钢裂纹起源于试样表面,通过不断扩展形成微裂纹,再连接成宏观裂纹,最终导致材料断裂。     

热轧双相钢微观应力-应变模型

利用扫描电子显微镜和透射电子显微镜对热轧后双相钢的微观组织进行分析,用Image-Pro Plus软件测定双相钢微观组织中各独立相的体积分数.根据多相材料中间混合法则和Swift方程,建立热轧双相钢微观应力-应变模型,并用DP590和DP780钢单向拉伸曲线进行验证.结果表明,该应力-应变关系微观模型基本阐明热轧双相钢微观组织参数与宏观力学性能的内在联系,能够准确地描述材料的变形行为,同时很好地预测热轧双相钢宏观的拉伸曲线.      

Q235钢结构材料的超低周疲劳性能

对钢结构材料 Q235钢的超低周疲劳性能进行了研究。采用横向应变控制方法,保持频率1 Hz 恒定,在岛津电液伺服疲劳试验机上开展了试验钢的超低周疲劳试验。获得了循环应力响应特征曲线等实验数据,并在此基础上分别建立了试验钢基于塑性应变幅及应变速率的超低周疲劳寿命预测公式,且2种公式均能较好地对其寿命进行预测。通过电镜扫描(SEM),分析了试验材料超低周疲劳下的微观断裂机理。研究结果表明,试验材料在超低周疲劳与低周疲劳下的疲劳性能,如循环响应特征、寿命预测公式以及微观断裂机理等方面均存在一定的差异。     

热轧DP600汽车用钢的微观结构特征与力学性能

为了研究热轧DP600汽车用钢的微观结构特征及力学性能,使用扫描电子显微镜(SEM)、透射电子显微镜(TEM)等分析了试验钢的组织、夹杂物及位错结构等,借助万能拉伸试验机测试了试验钢的强度与塑性。结果表明,热轧DP600汽车用钢的组织是铁素体+马氏体,随着应变量的增加,位错密度增加,位错缠结更为严重,在夹杂物与基体界面处、铁素体晶界处萌生微孔,马氏体发生断裂。热轧DP600试验钢的屈服强度为394.9 MPa,抗拉强度为641.6 MPa,塑性应变指数为0.154,屈强比为0.616,力学性能超过同级别的冷轧退火双相钢板指标。     

热轧双相钢DP600组织性能的研究

选择添加铬、钼合金元素的碳、锰、硅系的高强双相钢DP600为研究对象,选择Gleeble-3800热模拟试验机为研究方法测定了DP600动态CCT曲线,并模拟DP600双相钢热轧过程。采用金相组织观察、织构分析及力学性能测试等手段分析了不同工艺制度下双相钢组织及织构变化规律以及对性能的影响,从中获得最佳组织配比及优化的热轧工艺参数。根据优化的中试结果,进行了热轧双相钢DP600的工业试制。结果表明,试制样品的显微组织为铁素体及马氏体;屈强比均小于0.65,抗拉强度均在600 MPa以上;伸长率在24%以上;其拉伸曲线均为连续曲线,无屈服点伸长,具有典型的双相钢特征。     

16MnR 钢的高应变超低周疲劳性能

从压力容器的实际工况和抗震安全性设计出发,研究了压力容器用钢16MnR 钢的高应变超低周疲劳性能。采用横向应变控制方法,在 MTS809拉扭复合疲劳试验机上测定了试验钢应变疲劳过程中的循环应力响应特征及循环应力与应变的关系等超低周疲劳行为;通过拟合 Basquin 公式和 Coffin-Manson 公式,获得了试验钢的高应变超低周疲劳寿命预测公式。断口扫描发现,超低周疲劳下,多处裂纹萌生于试件表面,然后裂纹共同向内扩展,直到最后快速断裂。     

一种新型的低周疲劳裂纹扩展速率模型

基于低周疲劳裂纹扩展机制,假设裂纹尖端循环塑性区内应变分布服从HRR理论解,利用裂纹尖端锐化、钝化启裂低周疲劳裂纹扩展机制,结合Ramberg-Osgood循环应力应变曲线和Manson-Coffin疲劳寿命曲线等断裂力学理论,推导出一种新的低周疲劳裂纹扩展速率数学模型.与30Cr1Mo1V和St-4340的低周疲劳裂纹扩展速率试验数据进行对比,结果表明该低周疲劳裂纹扩展速率模型能够较好地预测材料的低周疲劳裂纹扩展速率.     

Production of auto-body dual-phase steel with single-step cooling on the output conveyer of the 2000 continuous broad-strip mill at OAO NLMK

The goal is to produce hot-rolled dual-phase steel of strength class DP 450–600 at OAO Novolipetskii Metallurgicheskii Kombinat (NLMK). The steel’s final structure and properties is greatly affected by single-stage strip cooling on the output roller conveyer of the 2000 continuous broad-strip mill. The influence of the hot-rolling parameters on the structure and mechanical properties of the hot-rolled SPRC440R steel from which cold-rolled dual-phase steel is produced at OAO NLMK is studied in the laboratory. The temperatures and rates for accelerated cooling on the output roller conveyer of the 2000 continuous broad-strip mill at OAO NLMK are calculated by means of a mathematical model. The laboratory data and simulation results are used in developing trial conditions for industrial rolling. Recommendations are made regarding the production of hot-rolled dual-phase steel corresponding to strength class DP 450–600.     

高强TRIP钢的动态力学性能

将Si-Mn系双相钢（DP钢）作为对比钢种,分析研究了高应变速率下600 MPa级Si-Mn系TRIP钢及含Al、Ni的1000 MPa级TRIP钢的显微组织及其动态力学性能.对DP钢而言,其抗拉强度随着应变速率的增大而升高,断裂延伸率则由于绝热温升的作用也呈上升趋势;对TRIP钢而言,随着应变速率的增大,其抗拉强度不断增大,断裂延伸率先减小后增大,但无法达到其静态拉伸时的塑性水平,这是由于在动态拉伸条件下奥氏体向马氏体的渐进式转变被抑制造成的.此外,在相同应变速率下测得的TRIP钢的绝热温升始终比DP钢高,而这部分高出的热量应当来自于在动态变形条件下TRIP钢中发生TRIP效应后释放的相变潜热.      

Fatigue characteristics of auto body sheet steels

The static and cyclic mechanical properties of a dual-phase steel and a TRIP steel having a comparable yield strength are studied. The effect of deformation and subsequent aging on the fatigue strength of the dual-phase steel is investigated, and the fractographic features of the fatigue fracture are analyzed.     

Research of DP600 high strength steel wheels

Steel has been used as a traditional wheel materials for a long time.Before 1980’ s,over 90% wheels were made of steels.Then,the yield strength of wheel steels increased gradually from 240 -350 MPa to 600 MPa or higher.The advanced high strength steels become the main wheel materials.Since 1990’s,DP600 has been broadly applied in steel wheels oversea.However,there was little research of application of high strength steel wheels(especially wheel disc) in domestic wheel industrial.In presence, DP600 steel wheel is only developed in FAWSH by using imported CKD.Other domestic steel wheel manufacturers did little work on high strength DP600 wheel discs.Baosteel wheels Co.Ltd.is the first domestic company producing DP600 steel discs and has become the leading company in production of high strength wheel.Because of the high strength of DP600,its formability,springback,and wrinkle have become the keys of the successful application of DP600 steel.In this paper,the metallurgical and mechanical properties are firstly introduced and formation problems of DP600 are described compared to traditional steels.Secondly,FLD analysis has been done.Wrinkle and more springback are recognized.To solve these problems,an optimized solution is designed and the good result is obtained.The test has shown that the fatigue property of steel wheel discs made by DP600 have been greatly improved.     

A Study of Spot Welding of Advanced High Strength Steels for Automotive Applications

The application of advanced high strength steels in automotive industry has highlighted the need for research into spot weldability of these steels.Using weld lobe diagrams,the spot weldability of DP600 steel was found to be poor with conventional weld schedules.An enhanced weld schedule consisting of two pulses with reduced current on the second pulse gave a substantial increase in the lobe width;the first pulse removed the zinc coating and the second pulse controlled the nugget growth.A data acquisition system was designed to monitor weld expulsion during the weld operation.Of the three possible control strategies proposed,especially with AC welding equipment,the dynamic resistance signal is easily obtained and the least expensive.Expulsion phenomena,microstructural characterization and mechanical properties of spot-welded hot dipped galvanized DP600 steel and interstitial free steel were investigated.Further work on dissimilar welds in DP 600 and HSLA 350 was also conducted with emphasis on tensile and fatigue properties and fracture characteristics.The performance of dissimilar spot welds was different from that of the similar spot welds in each of the HSLA350 and DP600 steels.The DP600 weld properties played a dominating role in the hardness and tensile properties of the dissimilar spot welds.However,the fatigue performance of the dissimilar welds was similar to that of the HSLA welds.Details will be presented at the conference.     

Shear Fracture of Advanced High Strength Steels

Failure experiments were carried out through a stretch-bending test system for advanced high strength steels, i.e. dual-phase （DP） steels and martensitic steels （MS）. The die radius in this system was designed from 1 to 15 mm to investigate the failure mode under different geometries. Two failure modes were observed during the ex- periments. As a result, critical relative radii （the ratio of inner bending radius R to sheet thickness t） for DP590 and DP780 steels were obtained. The stretch-bending tests of DP980 display some trends unlike DP590 and DP780 steels, and curve of DP980 in different thicknesses does not coincide well. High blank holder force exhibits more possibility of shear fracture tendency than low blank holder force. The unique character of high strength martensitic steel （1500MS） is that no shear fracture is found especially over small bending radius （R =2 mm） under the same experi- mental conditions. Microstructure analysis indicates that there are obviously elongated grains on shear fracture sur- face. It shows smaller diameter and shallower depth of the dimples than the necking failure.     

宝钢1880mm热轧试生产DP600双相钢的组织性能

采用Si-Mn系简单成分设计,充分发挥宝钢1 880 mm热连轧机组的密集冷却能力和卷取能力,通过密集水冷—空冷—水冷的三段式冷却模式和低温卷取,成功实现在1 880 mm机组工业试生产600 MPa级热轧双相钢。结果表明,通过合理的冷却速度、中间待温温度和待温时间配合,试验钢可获得铁素体和马氏体比例适合的双相组织,力学性能满足600 MPa级双相钢设计要求;同时试验发现,冷却和卷取工艺显著影响双相钢的微观组织和性能,因轧速变化造成钢卷头尾冷却条件不一致,导致钢卷不同位置力学性能波动较大。     

DP980钢及DP980钢激光焊接接头的高周疲劳性能

摘要：为了研究DP980钢的高周疲劳性能,采用疲劳试验机对DP980钢和DP980钢激光焊接接头进行高周疲劳试验,得到Basquin方程,并利用光学金相显微镜和扫描电镜进行组织和断口分析。结果表明：DP980钢激光焊接接头的焊缝根部和顶部出现形状凹陷,焊接接头的质量为中等。DP980钢疲劳极限为341MPa,DP980钢激光焊接接头的疲劳极限为148MPa,激光焊接接头的疲劳极限较母材的疲劳极限降低约50%。对于DP980钢而言,铁素体/马氏体晶界是裂纹萌生的主要位置,疲劳断口为准解理断口。对于DP980钢激光焊接接头而言,疲劳裂纹源位于焊缝凹陷处,而非热影响区及母材,疲劳断口为解理断口。DP980钢和DP980钢激光焊接接头的疲劳裂纹扩展区均有明显的疲劳条带,并伴随有二次裂纹。     

High cycle fatigue behavior of DP980 steel and DP980 steel laser welded joints

For the study of the DP980 steel high cycle fatigue property, high fatigue tests of DP980 steel and DP980 steel laser welded joints were carried out with fatigue testing machine, the Basquin equation was concluded. Microstructures and fractures were analyzed by optical microscope and scanning electron microscope. The results show that DP980 steel laser welding joints have the weld concavity at the welding root and top, the quality of welded joints is medium. The fatigue limit of DP980 steel is 341MPa, the fatigue limit of DP980 steel laser welded joint is 148MPa, the fatigue limit decreases by 50% compared with the fatigue limit of the base metal. For DP980 steel, the crystal boundary of the ferrite/martensite is the main location of micro cracks initiation, the fatigue fracture of DP980 steel is the quasi cleavage fracture. For DP980 steel laser welding joints, the fatigue cracks initiation is located in the weld concavity, not in the heat affected zone, the fatigue fracture is cleavage fracture. DP980 steel and DP980 steel laser welding joints crack propagation is characterized by the obviously fatigue striations coupled with secondary cracks.