Reduced Defects of MAPbI3 Thin Films Treated by FAI for High‐Performance Planar Perovskite Solar Cells

Organolead trihalide perovskite films with a large grain size and excellent surface morphology are favored to good‐performance solar cells. However, interstitial and antisite defects related trap‐states are originated unavoidably on the surfaces of the perovskite films prepared by the solution deposition procedures. The development of post‐growth treatment of defective films is an attractive method to reduce the defects to form good‐quality perovskite layers. Herein, a post‐treatment tactic is developed to optimize the perovskite crystallization by treating the surface of the one‐step deposited CH₃NH₃PbI₃ (MAPbI₃) using formamidinium iodide (FAI). Charge carrier kinetics investigated via time‐resolved photoluminescent, open‐circuit photovoltage decay, and time‐resolved charge extraction indicate that FAI post‐treatment will boost the perovskite crystalline quality, and further result in the reduction of the defects or trap‐states in the perovskite films. The photovoltaic devices by FAI treatment show much improved performance in comparison to the controlled solar cell. As a result, a champion solar cell with the best power conversion efficiency of 20.25% is obtained due to a noticeable improvement in fill factor. This finding exhibits a simple procedure to passivate the perovskite layer via regulating the crystallization and decreasing defect density.     

Two-Dimensional Metal–Organic Frameworks-Based Grain Termination Strategy Enables High-Efficiency Perovskite Photovoltaics with Enhanced Moisture and Thermal Stability

Perovskite degradation induced by surface defects and imperfect grain boundaries of films seriously damages the performance of perovskite solar cells (PSCs). Meanwhile, conventional organic molecules cannot maintain the long-time passivation effects under the stimulation of external environmental factors. Here, efficient and stable grain passivation in perovskite films is realized by preparing formic acid-functionalized 2D metal–organic frameworks (MOFs) as the terminated agent. Through robust interactions between exposed active sites and PbI₂, the 2D MOFs tightly caps the surface of PbI₂-terminated perovskite grains to stabilize the perovskite phases and aids the adhesion of adjacent grains. The MOFs mainly distributed at the grain boundaries of the perovskite film is directly observed at the microscopic scale. The modified perovskite films have regular morphology, lower defect density, and superior optoelectronic properties. Benefiting from the suppressed charge recombination and faster charge extraction, a power conversion efficiency of 21.28% is achieved for the best-performing PSC device. The unencapsulated PSCs with the MOFs modification maintain 88% and 81% of their initial efficiency after 750 h heating at 85  ° C under N₂ atmosphere and more than 1000 h storage in ambient environment (25  ° C, RH  ≈  40%), respectively.     

TiI4-doping induced bulk defects passivation in halide perovskites for high efficient photovoltaic devices

Power conversion efficiency (PCE) and stability are two important properties of perovskite solar cells (PSCs). Particularly, defects in the perovskite films could cause the generation of trap states, thereby increasing the nonradiative recombination. To address this issue, suitable dopants can be incorporated to react with non-bonded atoms or surface dangling bonds to passivate the defects. Herein, we introduced TiI₄ into CH₃NH₃PbI₃ (MAPbI₃) film and obtained a dense and uniform morphology with large crystal grains and low defect density. The champion cell based on 0.5% TiI₄-doped MAPbI₃ achieved a PCE as high as 20.55%, which is superior to those based on pristine MAPbI₃ (17.64%). Moreover, the optimal solar cell showed remarkable stability without encapsulation. It retained 88.03% of its initial PCE after 300 h of storage in ambient. This work demonstrates TiI₄ as a new and effective passivator for MAPbI₃ film.     

Crystal Growth Regulation of α-FAPbI3 Perovskite Films for High-Efficiency Solar Cells with Long-Term Stability

The two-step sequentially deposition strategy has been widely used to produce high-performance FAPbI₃-based solar cells. However, due to the rapid reaction between PbI₂ and FAI, a dense perovskite film forms on top of the PbI₂ layer immediately and blocks the FAI diffusion into the bottom of the PbI₂ film for a complete reaction, which results in a low-efficiency and limited reproducibility of perovskite solar cells (PSCs). Here, high-quality α-FAPbI₃ perovskite films by crystal growth regulation with 4-fluorobenzamide additives is fabricated. The additives can interact with FAI to suppress the fast reaction between the FAI and PbI₂ and effectively passivate the under-coordinated Pb²⁺ or I^- defects. As a result, α-FAPbI₃ perovskite films with low trap density and large grain size are prepared. The modified PSCs present a high-power conversion efficiency of 24.08%, maintaining 90% of their initial efficiency after 1400 h in high humidity. This study provides an efficient strategy of synergistic crystallization and passivation to form high-quality α-FAPbI₃ films for high-performance PSCs.     

Efficient Perovskite Hybrid Photovoltaics via Alcohol‐Vapor Annealing Treatment

In this work, alcohol‐vapor solvent annealing treatment on CH₃NH₃PbI₃ thin films is reported, aiming to improve the crystal growth and increase the grain size of the CH₃NH₃PbI₃ crystal, thus boosting the performance of perovskite photovoltaics. By selectively controlling the CH₃NH₃I precursor, larger‐grain size, higher crystallinity, and pinhole‐free CH₃NH₃PbI₃ thin films are realized, which result in enhanced charge carrier diffusion length, decreased charge carrier recombination, and suppressed dark currents. As a result, over 43% enhanced efficiency along with high reproducibility and eliminated photocurrent hysteresis behavior are observed from perovskite hybrid solar cells (pero‐HSCs) where the CH₃NH₃PbI₃ thin films are treated by methanol vapor as compared with that of pristine pero‐HSCs where the CH₃NH₃PbI₃ thin films are without any alcohol vapor treatment. In addition, the dramatically restrained dark currents and raised photocurrents give rise to over ten times enhanced detectivities for perovskite hybrid photodetectors, reaching over 10¹³ cm Hz^1/2 W^?1 (Jones) from 375 to 800 nm. These results demonstrate that the method provides a simple and facile way to boost the device performance of perovskite photovoltaics.     

Improved morphology and enhanced stability via solvent engineering for planar heterojunction perovskite solar cells

Solvent engineering technique for planar heterojunction perovskite solar cells is an efficient way to achieve uniformly controlled grain morphology for perovskite films. In this report, diethyl ether solvent engineering technique was used for Methyl ammonium lead triiodide (CH₃NH₃PbI₃) perovskite thin films for planar heterojunction solar cells which exhibited a PCE of 9.20%. Morphological improvements and enhanced grain sizes leads to enhanced absorption of CH₃NH₃PbI₃. Moreover solar cells have showed an excellent environmental stability of more than 100 days. This increase in efficiency is due to improved film morphology of perovskite layer after solvent treatment which has been revealed under UV–Vis spectroscopy, SEM images, X-ray diffraction and impedance spectroscopy.     

Synergistic Crystallization Modulation and Defects passivation via Additive Engineering Stabilize Perovskite Films for Efficient Solar Cells

Organic-inorganic lead halide perovskite are promising photovoltaic materials, but their intrinsic defects and crystalline quality severely deteriorate the solar cells efficiency and stability. Herein, potassium 1,1,2,2,3,3-hexafluoroprop-ane-1,3-disulfonimide (KHFDF) is introduced into PbI₂ precursor solution to passivate various defects and improve the crystalline quality of perovskite films. It is found that KHFDF can inhibit PbI₂ crystallization, thus tuning the crystal orientation and growth of perovskite films. Furthermore, KHFDF with dual-functional sulfonyl group cannot only passivate grain boundaries (GBs), but also passivate the defects at GBs via strong interaction with undercoordinated Pb²⁺ and/or hydrogen bonding with FA⁺, while the K⁺ counter cations allow ionic interaction with undercoordinated I⁻. As a result, the KHFDF-modified films exhibit high quality with a larger grain size and a reduced trap-state density, thereby suppressing the trap-state nonradiative recombination. And the devices show a champion efficiency up to 24.15%, benefiting from a sharp enhancement of open-circuit voltage (V_oc) of 1.183 V and fill factor of 81.78%. In addition, due to the enhanced humidity tolerance and chemical structure stability, the devices exhibit excellent long-term humidity and thermal stability without encapsulation.     

In situ recycle of PbI2 as a step towards sustainable perovskite solar cells

The development of organometal halide perovskite solar cells has grown rapidly and the highest efficiency of the devices has recently surpassed 22%. Because these solar cells contain toxic lead, a sustainable strategy is required to prevent environmental pollution and avoid healthy hazard caused by possible lead outflow. Here, in situ recycling PbI₂ from thermal decomposition CH₃NH₃PbI₃ perovskite films for efficient perovskite solar cells was developed. The thermal behavior of CH₃NH₃PbI₃ perovskite and its individual components were examined by thermogravimetric analysis. By optimizing the process of thermal decomposition CH₃NH₃PbI₃ film, the complete conversion from CH₃NH₃PbI₃ to pure PbI₂ layer with a mesoporous scaffold was achieved. The mesoporous structure readily promotes the conversion efficiency of perovskite and consequently results in high‐performance device. A perovskite crystal growth mechanism on the mesoporous PbI₂ structure was proposed. These results suggest that in situ recycled PbI₂ scaffolds can be a new route in manipulating the morphology of the perovskite active layer, providing new possibilities for high performance. Meanwhile, the risk of lead outflow can be released, and the saving‐energy fabrication of efficient solar cells can be realized.     

Polymer passivation of defects in inorganic perovskite solar cells

Inorganic perovskite solar cells (IPSCs) have attained attention due to their excellent thermal and phase stability. In this work, we demonstrate a novel approach for fabricating IPSCs, using the strategies of interface passivation and anti-solvent before spin-coating perovskite. Poly(methyl methacrylate) (PMMA) and chlorobenzene (CB) are used as passivator and anti-solvent, respectively. The CB improves the perovskite crystal morphology. Meanwhile, PMMA passivates the defects between poly(3, 4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) and perovskite layer, thus increasing the short-circuit current. Excitingly, we find that PMMA benefits the grain boundaries (GBs) of perovskite, which makes it more humidity-resistant, increasing the stability of perovskite film. Especially, PMMA mitigates interfacial charge losses, and the devices based on CsPbI3-xBrx passivated by PMMA exhibit the power conversion efficiency (PCE) much higher than those based on pure CsPbI3-xBrx.     

Impact of the Solvation State of Lead Iodide on Its Two‐Step Conversion to MAPbI3: An In Situ Investigation

Producing high efficiency solar cells without high‐temperature processing or use of additives still remains a challenge with the two‐step process. Here, the solution processing of MAPbI₃ from PbI₂ films in N,N‐dimethylformamide (DMF) is investigated. In‐situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) measurements reveal a sol–gel process involving three PbI₂‐DMF solvate complexes—disordered (P₀) and ordered (P₁, P₂)—prior to PbI₂ formation. When the appropriate solvated state of PbI₂ is exposed to MAI (methylammonium Iodide), it can lead to rapid and complete room temperature conversion into MAPbI₃ with higher quality films and improved solar cell performance. Complementary in‐situ optical reflectance, absorbance, and quartz crystal microbalance with dissipation (QCM‐D) measurements show that dry PbI₂ can take up only one third of the MAI taken up by the solvated‐crystalline P₂ phase of PbI₂, requiring additional annealing and yet still underperforming. The perovskite solar cells fabricated from the ordered P₂ precursor show higher power conversion efficiency (PCE) and reproducibility than devices fabricated from other cases. The average PCE of the solar cells is greatly improved from 13.2(±0.53)% (from annealed PbI₂) to 15.7(±0.35)% (from P₂) reaching up to 16.2%. This work demonstrates the importance of controlling the solvation of PbI₂ as an effective strategy for the growth of high‐quality perovskite films and their application in high efficiency and reproducible solar cells.     

Grain Boundary and Interface Passivation with Core–Shell Au@CdS Nanospheres for High‐Efficiency Perovskite Solar Cells

The plasmonic characteristic of core–shell nanomaterials can effectively improve exciton‐generation/dissociation and carrier‐transfer/collection. In this work, a new strategy based on core–shell Au@CdS nanospheres is introduced to passivate perovskite grain boundaries (GBs) and the perovskite/hole transport layer interface via an antisolvent process. These core–shell Au@CdS nanoparticles can trigger heterogeneous nucleation of the perovskite precursor for high‐quality perovskite films through the formation of the intermediate Au@CdS–PbI₂ adduct, which can lower the valence band maximum of the 2,2,7,7‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)9,9‐spirobifluorene (Spiro‐OMeTAD) for a more favorable energy alignment with the perovskite material. With the help of the localized surface plasmon resonance effect of Au@CdS, holes can easily overcome the barrier at the perovskite/Spiro‐OMeTAD interface (or GBs) through the bridge of the intermediate Au@CdS–PbI₂, avoiding the carrier accumulation, and suppress the carrier trap recombination at the Spiro‐OMeTAD/perovskite interface. Consequently, the Au@CdS‐based perovskite solar cell device achieves a high efficiency of over 21%, with excellent stability of ≈90% retention of initial power conversion efficiencies after 45 days storage in dry air.     

Thin Films of Dendritic Anatase Titania Nanowires Enable Effective Hole‐Blocking and Efficient Light‐Harvesting for High‐Performance Mesoscopic Perovskite Solar Cells

To achieve high‐performance perovskite solar cells, especially with mesoscopic cell structure, the design of the electron transport layer (ETL) is of paramount importance. Highly branched anatase TiO₂ nanowires (ATNWs) with varied orientation are grown via a facile one‐step hydrothermal process on a transparent conducting oxide substrate. These films show good coverage with optimization obtained by controlling the hydrothermal reaction time. A homogeneous methyl­ammonium lead iodide (CH₃NH₃PbI₃) perovskite thin film is deposited onto these ATNW films forming a bilayer architecture comprising of a CH₃NH₃PbI₃ sensitized ATNW bottom layer and a CH₃NH₃PbI₃ capping layer. The formation, grain size, and uniformity of the perovskite crystals strongly depend on the degree of surface coverage and the thickness of the ATNW film. Solar cells constructed using the optimized ATNW thin films (220 nm in thickness) yield power conversion efficiencies up to 14.2% with a short‐circuit photocurrent density of 20.32 mA cm^?2, an open‐circuit photovoltage of 993 mV, and a fill factor of 0.70. The dendritic ETL and additional perovskite capping layer efficiently capture light and thus exhibit a superior light harvesting efficiency. The ATNW film is an effective hole‐blocking layer and efficient electron transport medium for excellent charge separation and collection within the cells.     

Viscosity effect of ionic liquid-assisted controlled growth of CH3NH3PbI3 nanoparticle-based planar perovskite solar cells

A precise control of the morphology and crystallization of perovskite thin-films is well-correlated to higher perovskite solar cells performances. Ionic liquids (ILs) can retard perovskite crystallization to aid the formation of films with uniform morphology to realize highly efficient perovskite solar cells. Herein, we attempt to control the nanostructural growth of CH₃NH₃PbI₃ thin films by adding ILs to the perovskite spin-coating solution and investigate the effect of IL viscosity on the resulting CH₃NH₃PbI₃ nanoparticle (NP) thin films. NPs with desirable morphology were obtained using ILs with a low viscosity that completely dissolved in the CH₃NH₃PbI₃ solution. In particular, the IL tetrabutylammonium chloride yielded NPs with a diameter of 500 nm and controllable morphology, crystallinity, and absorption behavior, which led to improved photovoltaic performance compared with that of solar cells containing NPs produced using other ILs. Our findings revealed a pathway to obtain uniformly distributed CH₃NH₃PbI₃ NP thin films for use in perovskite solar cells. The developed method is well suited for large-scale production of perovskite thin films on flexible substrates.     

HPbI3: A New Precursor Compound for Highly Efficient Solution‐Processed Perovskite Solar Cells

Recently, there have been extensive research efforts on developing high performance organolead halide based perovskite solar cells. While most studies focused on optimizing the deposition processes of the perovskite films, the selection of the precursors has been rather limited to the lead halide/methylammonium (or formamidium) halide combination. In this work, we developed a new precursor, HPbI₃, to replace lead halide. The new precursor enables formation of highly uniform formamidium lead iodide (FAPbI₃) films through a one‐step spin‐coating process. Furthermore, the FAPbI₃ perovskite films exhibit a highly crystalline phase with strong (110) preferred orientation and excellent thermal stability. The planar heterojunction solar cells based on these perovskite films exhibit an average efficiency of 15.4% and champion efficiency of 17.5% under AM 1.5 G illumination. By comparing the morphology and formation process of the perovskite films fabricated from the formamidium iodide (FAI)/HPbI₃, FAI/PbI₂, and FAI/PbI₂ with HI additive precursor combinations, it is shown that the superior property of the HPbI₃ based perovskite films may originate from 1) a slow crystallization process involving exchange of H⁺ and FA⁺ ions in the PbI₆ octahedral framework and 2) elimination of water in the precursor solution state.     

Chlorobenzene vapor assistant annealing method for fabricating high quality perovskite films

In this study, chlorobenzene (CB) vapor assistant annealing (VAA) method is employed to make high quality perovskite films and produce high efficiency CH₃NH₃PbI_3-xCl_x perovskite solar cells. The perovskite films made by this method present several advantages such as increased crystallinity, large grain size and reduced crystal boundaries compared with those prepared by thermal annealing (TA) method, which is beneficial to charge dissociation and transport in hybrid photovoltaic device. In addition, it is found that the CB VAA method could improve the surface property of perovskite film, resulting in a preferable coverage of PCBM layer and a better interfacial contact between perovskite film and upper PCBM film. Consequently, the short circuit current density (J_sc) of the devices is significantly increased, yielding a high efficiency of 14.79% and an average efficiency of 13.40%, which is 13% higher than that of thermal annealed ones. This work not only put forward a simple and efficient approach to prepare highly efficient perovskite solar cells but also provide a new idea to improve the morphology and interfacial contact in one integration step.     

Efficient lead acetate sourced planar heterojunction perovskite solar cells with enhanced substrate coverage via one-step spin-coating

In planar heterojunction (PHJ) perovskite solar cells (PerSCs) without mesoporous metal oxide skeleton, there is challenge of formation perovskite film with full coverage to the conductive substrate through solution-process the lead halide precursors. Selecting a lead source with more volatile byproducts is an effective approach to obtain much smoother films with smaller and fewer pinholes. Herein, we demonstrate efficient CH₃NH₃PbI₃/PCBM PHJ PerSCs by using lead acetate (Pb(Ac)₂) as lead precursor. The morphology of the perovskite thin films were investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively, and the crystalline quality of the perovskite films were investigated by X-ray diffraction (XRD) spectroscopy. Time-resolved photoluminescence (TRPL) was used to investigate the PL lifetime of the perovskite film. The perovskite film derived from Pb(Ac)₂ shows enhanced surface coverage and improved photoluminescence lifetime in comparison with PbI₂ sourced perovskite film. Averaged over 20 individual devices, the power conversion efficiency (PCE) of devices derived from Pb(Ac)₂ reaches 14.81%, much higher than PbI₂ sourced devices by one-step (8.23%) or two-step (10.58%) spin-coating.     

Enhancing Stability of Efficient Perovskite Solar Cells (PCE ≈ 24.5%) by Suppressing PbI2 Inclusion Formation

Excess lead(II) iodide (PbI₂) has controversial roles in affecting the efficiency of perovskite solar cells (PSCs). Since the photoinstability of PbI₂ is now known to largely accelerate perovskite degradation, suppressing and/or eliminating excess PbI₂ is key to improving the stability of PSCs. Herein, process-dependent PbI₂ formation on the surfaces of formamidinium lead triiodide (FAPbI₃) films is examined. Due to the faster evaporation rate of organic substances, crystalline PbI₂ as an inclusion is found within the triple junction grain boundaries. With this hypothesis, two strategies are suggested: control of the 1) vapor pressure and 2) stoichiometry of precursor solutions to induce sufficient reaction of FAPbI₃. Although both strategies successfully eliminate the PbI₂ as inclusions, due to the slower evaporation rate, vapor pressure control films also exhibit a larger grain size (≈1.18 µm) with a good film quality to attain the highest power conversion efficiency (PCE) of 24.5%. Furthermore, the phase stability of α-FAPbI₃ is improved due to the elimination of the degradation sites induced by the photoinstability of PbI₂. The findings explore the formation process of unwanted PbI₂ (≈2.8%) and provide a simple method to effectively suppress its formation. This may further boost the PCE and stability, especially for FA-based perovskites.     

Precursor Engineering for All‐Inorganic CsPbI2Br Perovskite Solar Cells with 14.78% Efficiency

The optoelectronic properties of perovskite films are closely related to the film quality, so depositing dense, uniform, and stable perovskite films is crucial for fabricating high‐performance perovskite solar cells (PSCs). CsPbI₂Br perovskite, prized for its superb stability toward light soaking and thermal aging, has received a great deal of attention recently. However, the air instability and poor performance of CsPbI₂Br PSCs are hindering its further progress. Here, an approach is reported for depositing high‐quality CsPbI₂Br films via the Lewis base adducts PbI₂(DMSO) and PbBr₂(DMSO) as precursors to slow the crystallization of the perovskite film. This process produces CsPbI₂Br films with large‐scale crystalline grains, flat surfaces, low defects, and long carrier lifetimes. More interestingly, PbI₂(DMSO) and PbBr₂(DMSO) adducts could significantly improve the stability of CsPbI₂Br films in air. Using films prepared by this technique, a power conversion efficiency (PCE) of 14.78% is obtained in CsPbI₂Br PSCs, which is the highest PCE value reported for CsPbI₂Br‐based PSCs to date. In addition, the PSCs based on DMSO adducts show an extended operational lifetime in air. These excellent performances indicate that preparing high‐quality inorganic perovskite films by using DMSO adducts will be a potential method for improving the performance of other inorganic PSCs.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

Low temperature fabrication of formamidinium based perovskite solar cells with enhanced performance by chlorine incorporation

Recently formamidinium (FA) based perovskite solar cell was demonstrated to show high performance and better stability upon partial substitution of FA with Cs cation. However, the fabrication of device required high-temperature processing on TiO₂ electrode and thus limits the use of flexible polymeric substrates. Here, we present a low temperature approach for the fabrication of p-i-n perovskite solar cells based on Cs_0.15FA_0.85PbI₃. Furthermore, we investigated the effects of chlorine on the morphology and crystallinity of the perovskite films and the corresponding photovoltaic performance. Chlorine incorporation can significantly enlarge the size of grains and improve the crystallinity of perovskite films with full surface coverage. A best power conversion efficiency of 14.5% was realized for planar perovskite solar cells with negligible hysteresis and remarkable reproducibility.