Reduced Switch Count DC-Link AC–AC Five-Leg Converter

This paper investigates a reduced switch count dc-link ac–ac five-leg converter for three-phase power conversion. The converter provides both an input rectifier and an output inverter by sharing a leg in order to reduce the number of power switches. Scalar and vector pulsewidth modulation techniques are presented and the concepts of local and global apportioning factors are introduced. A control technique that aims at maximizing the utilization of the dc-link voltage is proposed. A hysteresis current controller that allows operating with one leg being shared by the load and grid sides is developed. In addition, several relevant characteristics of the converter are addressed, such as voltage capability, harmonic distortion, shared-leg and capacitor currents, and power rating. The features of such a converter are compared to those of the six-leg and four-leg converters. Selected experimental results are presented.     

An AC VRM topology for high frequency AC power distribution systems

In this paper, a series resonant converter with pulse-width modulation (PWM) control is presented as an ac voltage regulator module (VRM) for high frequency ac power distribution systems. The proposed topology has close-to-unity rated power factor, low total harmonic distortion in input current, zero voltage switching under all load conditions, low voltage stress of the active switch and high overall efficiency. Simulation and experimental results are presented to prove the performance of the proposed ac VRM converter.     

Control of Single-Phase-to-Three-Phase AC/DC/AC PWM Converters for Induction Motor Drives

This paper proposes a novel control scheme of single-phase-to-three-phase pulsewidth-modulation (PWM) converters for low-power three-phase induction motor drives, where a single-phase half-bridge PWM rectifier and a two-leg inverter are used. With this converter topology, the number of switching devices is reduced to six from ten in the case of full-bridge rectifier and three-leg inverter systems. In addition, the source voltage sensor is eliminated with a state observer, which controls the deviation between the model current and the system current to be zero. A simple scalar voltage modulation method is used for a two-leg inverter, and a new technique to eliminate the effect of the dc-link voltage ripple on the inverter output current is proposed. Although the converter topology itself is of lower cost than the conventional one, it retains the same functions such as sinusoidal input current, unity power factor, dc-link voltage control, bidirectional power flow, and variable-voltage and variable-frequency output voltage. The experimental results for the V/f control of 3-hp induction motor drives controlled by a digital signal processor TMS320C31 chip have verified the effectiveness of the proposed scheme     

Lagrangian modeling and passivity-based control of three-phase AC/DC voltage-source converters

In this paper, we investigate the dc-bus voltage regulation problem for a three-phase boost-type pulsewidth-modulated (PWM) ac/dc converter using passivity-based control theory of Euler-Lagrange (EL) systems. The three-phase PWM ac/dc converters modeled in the a-b-c reference frame are first shown to be EL systems whose EL parameters are explicitly identified. The energy-dissipative properties of this model are fully retained under the d-q-axis transformation. Based on the transformed d-q EL model, passivity-based controllers are then synthesized using the techniques of energy shaping and damping injection. Two possible passivity-based feedback designs are discussed, leading to a feasible dynamic current-loop controller. Motivated from the usual power electronics control schemes and the study of Lee, the internal dc-bus voltage dynamics are regulated via an outer loop proportional plus integral (PI) controller cascaded to the d-axis current loop. Nonlinear PI control results of Desoer and Lin are applied to theoretically validate the proposed outer loop control scheme. The PWM ac/dc converter controlled by the proposed passivity-based current control scheme with outer loop PI compensation has the features of enhanced robustness under model uncertainties, decoupled current-loop dynamics, guaranteed zero steady-state error, and asymptotic rejection of constant load disturbance. Experimental results on a 1.5-kVA PC-based controlled prototype provide verification of these salient features. The experimental responses of a classical linear PI scheme are also included for comparative study.     

A General PWM Strategy for Four-Switch Three-Phase Inverters

A general pulsewidth modulation (PWM) method for control of four-switch three-phase inverters is presented. The proposed vector PWM offers a simple method to select three or four vectors that effectively synthesize the desired output voltage, even in presence of voltage oscillations across the two dc-link capacitors. The method utilizes the so called space vector modulation, and includes its scalar version. Different vector combinations are compared. The effect of Wye and delta motor winding connections over the pulse width modulator is also considered. The common mode voltage generated by the four-switch three-phase converter is evaluated and compared to that provided by the standard six-switch three-phase inverter. Simulation and experimental results are presented to demonstrate the feasibility of the proposed approach     

Improved Direct Power Control of Grid-Connected DC/AC Converters

This paper proposes new direct power control (DPC) strategies for three-phase dc/ac converters with improved dynamic response and steady-state performance. As with an electrical machine, source and converter flux, which equal the integration of the respective source and converter voltage, are used to define active and reactive power flow. Optimization of the lookup table used in conventional DPC is outlined first so as to improve power control and reduce current distortion. Then, constant switching frequency DPC is developed where the required converter voltage vector within a fixed half switching period is calculated directly from the active and reactive power errors. Detailed angle compensation due to the finite sampling frequency and the use of an integral controller to further improve the power control accuracy are described. Both simulation and experimental results are used to compare conventional DPC and vector control, and to demonstrate the effectiveness and robustness of the proposed control strategies during active and reactive power steps, and line inductance variations.      

Single-phase Z-source PWM AC-AC converters

The letter proposes a new family of simple topologies of single-phase PWM ac-ac converters with a minimal number of switches: voltage-fed Z-source converter and current-fed Z-source converter. By PWM duty-ratio control, they become "solid-state transformers" with a continuously variable turns ratio. All the proposed ac-ac converters in this paper employ only two switches. Compared to the existing PWM ac-ac converter circuits, they have unique features: providing a larger range of output ac voltage with buck-boost, reversing or maintaining phase angle, reducing in-rush and harmonic current, and improving reliability. The operating principle and control method of the proposed topologies are presented. Analysis, simulation, and experimental results are given using the voltage-fed Z-source ac-ac converter as an example. The analysis can be easily extended to other converters of the proposed family. The proposed converters could be used in voltage regulation, power regulation, and so on.     

Three-Phase Three Level, Soft Switched, Phase Shifted PWM DC–DC Converter for High Power Applications

A new three-phase, three-level dc to dc phase shifted pulsewidth modulation (PWM) converter is proposed for high power and high input voltage applications. Output voltage is controlled by incorporating phase shift PWM. Clocked gate signals of each leg are phase shifted by 2pi/3 from each other. Major features of the converter include: (1) outer two switches of each leg are turned on and off as zero voltage switching, (2) inner two switches of each leg are turned on and off as zero current switching, and (3) this is achieved without involving any extra passive or active components. The secondary side of the converter is of center tapped full-wave current tripler type. This results in an increase of ripple frequency by a factor of six, leading to a significant reduction in size of the output filter. In order to obtain behavioral and performance characteristics of the proposed converter topology, detailed analytical and simulation studies are carried out. Finally the viability of the scheme is confirmed through detailed experimental studies on a laboratory prototype developed for the purpose.     

High-frequency link inverter for fuel cells based on multiple-carrier PWM

Fuel-cell inverter applications typically have a relatively low voltage input, and require a battery bus for energy buffering. Circuit topology issues are examined based on these needs. The need for high step-up ratios, current control, low ripple, and battery storage leads to a current-sourced link converter as perhaps the best choice of conversion topology. High-frequency ac link conversion offers a possible way to reduce the number of power stages, in the form of a cycloconverter, known from previous work. It is shown that the control complexity in this converter can be addressed by adapting pulse-width modulation (PWM) techniques. Here, a multicarrier PWM approach is introduced as a convenient way to implement a high-frequency link inverter. The approach is a direct extension of conventional PWM, and supports square-wave cycloconversion methods that have appeared in prior literature. Simulation and experimental results are developed for a low-voltage ac link inverter, leading to a 48-V fuel cell input design.     

基于PWM AC-AC变换的电压补偿器设计

介绍在配电系统中一种新型的电压补偿器,即在自耦变压器中集成PWM AC-AC变换器(每相4个IGBT元件)。其电压补偿控制模块根据系统控制对象的特点,选取数字化控制芯片TMS320LF2407,设计了基于DSP的PWM实现方式。在正常工作状况下,PWM变换器工作在旁路方式,电源功率直接传输给负荷,自耦变压器只吸收励磁电流;而当电压降低时,变换器将电压迭加(补偿)上去,以保持负荷端电压为额定值,同时通过自耦变压器增加一定的输出功率。在设计中没有使用诸如成组电容器/电感等这些储能元件,造价低,响应速度快。     

A new state feedback based transient control of PWM AC to DCvoltage type converters

This paper presents a new state feedback based control strategy for a PWM AC to DC voltage type converter with phase and amplitude control. In this control strategy the state variables of the LC filter connected to the AC side of the converter are fed back to the PWM pattern generator, thereby eliminating a DC offset of the AC input currents as well as oscillations of the DC output current during transients. Computer simulation of the converter system with the proposed control strategy shows that the transient waveforms of AC input and DC output currents are improved greatly even if the damping effect of the AC side resistance can not be expected. The DC voltage regulation with good dynamic response is also achieved even if DC capacitance is substantially reduced. Experimental results from a low power laboratory model are also included to confirm the simulated results and to demonstrate the effectiveness of the proposed control strategy     

A novel ZCS-PWM power-factor preregulator with reduced conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 50 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.3% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

Low switching frequency space vector modulators for high power multimodule converters

Force-commutated multiconverter systems have been proposed and recently implemented for high power applications, particularly high-voltage direct current (HVDC) transmission and flexible ac transmission systems (FACTS) devices, including STAtic var COMpensators (STATCOM). This paper demonstrates that pulse-width modulation (PWM) based on space vector modulation (SVM), and using low switching frequencies (a few hundred Hertz) can be implemented in multimodule power converter systems. The proposed scheme is based on a delayed sampling technique and allows output voltage control and minimization of harmonic components. Pattern generation options are analyzed and system waveforms are presented for different switching frequencies and number of modules. Results are validated by simulation and confirmed by experiments on a 5-kVA prototype unit.     

Interleaved ZVS Converter With Ripple-Current Cancellation

In this paper, an interleaved soft-switching converter with ripple-current cancellation is presented to achieve zero- voltage-switching (ZVS) turn-on and load current sharing. In order to achieve ZVS turn-on, an active snubber is connected in parallel with the primary winding of the transformer. The energy stored in the transformer leakage inductance and magnetizing inductance can be recovered so that the peak voltage stress of switching devices is limited. The resonance at the transition interval is used to realize ZVS turn-on of all switches. In order to achieve three-level pulsewidth-modulation (PWM) scheme, an addition fast-recovery diode is used in the converter. Three-level PWM scheme can reduce the ac ripple current on the output inductor such that the output inductor can be reduced. The current-doubler rectifier is adopted in the secondary side of the transformer to reduce the transformer secondary-winding current and output voltage ripple by canceling the current ripple of two output inductors. The output voltage is controlled at the desired value using the interleaved PWM scheme. These features make the proposed converter suitable for the dc-dc converter with high output current. The operation principles, steady state analysis, and design equations of the proposed converter are provided in detail. Finally, experiments based on a 600-W (12 V/50 A) prototype are provided to verify the effectiveness and feasibility of the proposed converter.     

Zero-voltage and zero-current-switching PWM hybrid full-bridge three-level converter

This paper proposes a zero-voltage and zero-current-switching pulsewidth modulation hybrid full-bridge three-level (ZVZCS PWM H-FB TL) converter, which has a TL leg and a two-level leg. The voltage stress of the switches of the TL leg is half of the input voltage, and the switches can realize ZVS, so MOSFETs can be adopted; the voltage stress of the switches of the two-level leg is the input voltage, and the switches can realize ZCS, so IGBT can be adopted. The secondary rectified voltage is a TL waveform having lower high-frequency content compared with that of the traditional FB converters, which leads to the reduction of the output filter inductance. The input current of the converter has quite little ripple, so the input filter can also be significantly reduced. The operation principle of the proposed converter is analyzed and verified by the experimental results. Several ZVZCS PWM H-FB TL converters are also proposed in this paper.     

The three-level ZVS-PWM DC-to-DC converter

A novel high-frequency DC-to-DC power converter for high voltage and high power is introduced which features zero voltage switching (ZVS), operation at constant frequency, regulation by pulse width modulation (PWM), and low RMS current stress upon power switches. Its greatest attribute, in comparison with the full-bridge (FB-ZVS-PWM) converter, is that the voltage across the switches is half of the input voltage, This property is achieved due to the use of a three-level leg in place of the conventional two-switch leg. Operation, analysis, design procedure and example, and simulation are presented. A prototype operating at 100 kHz, rated at 600 V input voltage, and 1.5 kW output power and 25 A output current has been fabricated and successfully tested in the laboratory. The measured efficiency at full load was 93%     

A Single-Phase Active Filter Using an H-Bridge PWM Converter With a Sampling Frequency Quadruple of the Switching Frequency

This paper presents a digital current regulator for H-bridge pulsewidth modulation (PWM) converters, whose sampling frequency equals quadruple of the switching frequency. The current regulator detects the ac current and manipulates the voltage reference not only at the upper and lower peaks of the PWM triangle carrier but also at its zero crossings. This paper theoretically discusses the switching sequence of the H-bridge PWM converter, and reveals the amount of the voltage error and the condition where the voltage error occurs. A modified deadbeat current regulator is proposed to suppress the current oscillation induced by the voltage error, based on the theoretical analysis. Experimental results are shown to verify the control performance of the proposed current regulator. Moreover, a proposed current regulator is applied to a single-phase active power filter to demonstrate the effectiveness in harmonic compensation.     

基于双向PWM变换器的微燃机发电系统起动／发电控制研究

针对微型燃气轮机（微燃机）发电系统的特点,建立了以电压型双向脉宽调制（PwM）变换器为功率变换装置的起动／发电控制模型。微型燃气轮机发电系统起动时,采用矢量控制;发电运行时,采用电压外环电流内环的双环PWM整流控制。仿真实验结果表明：起动时,高速永磁同步电机（PMSG）采用矢量控制比速度开环控制性能更优,减少了起动时间,满足快速起动的要求;发电运行时,与二极管整流相比,PWM整流能使交流侧电流跟踪发电机的感应电动势,功率因数约为1,降低了发电机侧的电流谐波,即减少了谐波热。同时保证了发电机在一定宽速范围内,输出直流电压稳定,并且在起动一发电过渡转换过程中,直流母线电压降落后,快速恢复为稳定值,满足平滑转换的要求。     

A Novel Three-Phase Three-Leg AC/AC Converter Using Nine IGBTs

This paper proposes a novel three-phase nine-switch ac/ac converter topology. This converter features sinusoidal inputs and outputs, unity input power factor, and more importantly, low manufacturing cost due to its reduced number of active switches. The operating principle of the converter is elaborated; its modulation schemes are discussed. Simulated semiconductor loss analysis and comparison with the back-to-back two-level voltage source converter are presented. Finally, experimental results from a 5-kVA prototype system are provided to verify the validity of the proposed topology.     

High-precision current source using low-loss, single-switch,three-phase AC/DC converter

A three-phase AC/DC converter based on isolated Cuk topology feeding an inductive load is presented. The main goal is to get a compact, highly stable current source to feed an electromagnet. A high power factor is achieved, at constant duty-cycle and switching frequency, by discontinuous input current mode operation. The converter presents a linear relationship between the duty-cycle and the output current, making it easier to design the control system. Additionally the voltage stress on the power transistor is constant and does not depend on the duty-cycle. An auxiliary circuit allows zero voltage turn-off while limiting the over-voltage on the switch produced by the transformer leakage inductance. Pulse-width modulation (PWM) control is used to reduce sensitivity to line disturbances and to eliminate the 300-Hz ripple on the output current. Experimental measurements taken on a 400-W prototype confirm theoretical forecasts