AI/W/TiN/AI及AI/W/TiW/AI结构特性研究

本文研究了H_2还原WF_6在α-Si/TiN/Al和TiW/Al衬底上LPCVD生长钨膜的特性。测量和分析了Al/W/TiN/Al和Al/W/TiW/Al结构的接触电阻和界面特性,研究了两种结构的热稳定性。结果表明,H_2还原WF_6可以在α-Si/TiN/Al和TiW/Al衬底上实现选择性钨淀积,钨膜质量较好。Al/W/TiN/Al和Al/W/TiW/Al结构接触电阻率为10~(-?)Ωcm~2量级,远低于难熔金属硅化物同硅的欧姆接触电阻率。两种结构的热稳定性良好。采用TiN或TiW作为Al和W之间的隔离层,CVD-W填充互连层连通孔可以满足多层金属平坦化互连技术的要求。     

Performance improvement in tensile-strained In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As metamorphic HEMT

This paper proposes a In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As (x=0.3-0.5-0.3) metamorphic high-electron mobility transistor with tensile-strained channel. The tensile-strained channel structure exhibits significant improvements in dc and RF characteristics, including extrinsic transconductance, current driving capability, thermal stability, unity-gain cutoff frequency, maximum oscillation frequency, output power, power gain, and power added efficiency.     

Very low-noise Al/sub 0.3/Ga/sub 0.7/As/Ga/sub 0.65/In/sub 0.35/As/GaAs single quantum-well pseudomorphic HEMTs

AlGaAs/GaInAs/GaAs pseudomorphic HEMTs with an InAs mole fraction as high as 35% in the channel has been successfully fabricated. The device exhibits a maximum extrinsic transconductance of 700 mS/mm. At 18 GHz, a minimum noise figure of 0.55 dB with 15.0 dB associated gain was measured. At 60 GHz, a minimum noise figure as low as 1.6 dB with 7.6 dB associated gain was also obtained. This is the best noise performance yet reported for GaAs-based HEMTs.<>     

A 12 /spl times/ 12 In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiode array

We report a 12 /spl times/ 12 In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiode (APD) array. The mean breakdown voltage of the APD was 57.9 V and the standard deviation was less than 0.1 V. The mean dark current was /spl sim/2 and /spl sim/300 nA, and the standard deviation was /spl sim/0.19 and /spl sim/60 nA at unity gain (V/sub bias/ = 13.5 V) and at 90% of the breakdown voltage, respectively. External quantum efficiency was above 40% in the wavelength range from 1.0 to 1.6 /spl mu/m. It was /spl sim/57% and /spl sim/45% at 1.3 and 1.55 /spl mu/m, respectively. A bandwidth of 13 GHz was achieved at low gain.     

Morphological and electrical characterization of SixCryCzBv thin films

Si_xCr_yC_zB_v thin films with several compositions have been studied for integration of high precision resistors in 0.8 μm BICMOS technology. These resistors, integrated in the back-end of line, have the advantage to provide high level of integration and attractive electrical behavior in temperature, for analog devices. The film morphology and the structure have been investigated through transmission electron microscopy analysis and have been then related to the electrical properties on the base of the percolation theory. According to this theory, and in agreement with experimental results, negative thermal coefficient of resistance (TCR) has been obtained for samples with low Cr content, corresponding to a crystalline volume fraction below the percolation threshold.Samples with higher Cr content exhibit, instead, a variation of the TCR as a function of film thickness: negative TCR values are obtained for thickness lower than 5 nm, corresponding to a crystalline volume fraction below the percolation threshold; positive TCR are obtained for larger thickness, indicating the establishment of a continuous conductive path between the Cr rich grains. This property seems to be determinant in order to assure the possibility to obtain thin film resistors almost independent on the temperature.     

Al/sub 0.3/Ga/sub 0.7/As/In/sub x/Ga/sub 1-x/As (0/spl les/x/spl les/0.25) doped-channel field-effect transistors (DCFET's)

The properties of both lattice-matched and strained doped-channel field-effect transistors (DCFET's) have been investigated in AlGaAs/In/sub x/Ga/sub 1-x/As (0/spl les/x/spl les/0.25) heterostructures with various indium mole fractions. Through electrical characterization of grown layers in conjunction with the dc and microwave device characteristics, we observed that the introduction of a 150-/spl Aring/ thick strained In/sub 0.15/Ga/sub 0.85/As channel can enhance device performance, compared to the lattice-matched one. However, a degradation of device performance was observed for larger indium mole fractions, up to x=0.25, which is associated with strain relaxation in this highly strained channel. DCFET's also preserved a more reliable performance after biased-stress testings.<>     

Comparison between Pt/TiO2/Pt and Pt/TaOX/TaOY/Pt based bipolar resistive switching devices

Nonvolatile memories have emerged in recent years and have become a leading candidate towards replacing dynamic and static random-access memory devices. In this article, the performances of TiO₂ and TaO₂ nonvolatile memristive devices were compared and the factors that make TaO₂ memristive devices better than TiO₂ memristive devices were studied. TaO₂ memristive devices have shown better endurance performances (10⁸ times more switching cycles) and faster switching speed (5 times) than TiO₂ memristive devices. Electroforming of TaO₂ memristive devices requires~4.5 times less energy than TiO₂ memristive devices of a similar size. The retention period of TaO₂ memristive devices is expected to exceed 10 years with sufficient experimental evidence. In addition to comparing device performances, this article also explains the differences in physical device structure, switching mechanism, and resistance switching performances of TiO₂ and TaO₂ memristive devices. This article summarizes the reasons that give TaO₂ memristive devices the advantage over TiO₂ memristive devices, in terms of electroformation, switching speed, and endurance.     

Highly linear Al/sub 0.3/Ga/sub 0.7/N-Al/sub 0.05/Ga/sub 0.95/N-GaN composite-channel HEMTs

We report an Al/sub 0.3/Ga/sub 0.7/N-Al/sub 0.05/Ga/sub 0.95/N-GaN composite-channel HEMT with enhanced linearity. By engineering the channel region, i.e., inserting a 6-nm-thick AlGaN layer with 5% Al composition in the channel region, a composite-channel HEMT was demonstrated. Transconductance and cutoff frequencies of a 1 /spl times/100 /spl mu/m HEMT are kept near their peak values throughout the low- and high-current operating levels, a desirable feature for linear power amplifiers. The composite-channel HEMT exhibits a peak transconductance of 150 mS/mm, a peak current gain cutoff frequency (f/sub T/) of 12 GHz and a peak power gain cutoff frequency (f/sub max/) of 30 GHz. For devices grown on sapphire substrate, maximum power density of 3.38 W/mm, power-added efficiency of 45% are obtained at 2 GHz. The output third-order intercept point (OIP3) is 33.2 dBm from two-tone measurement at 2 GHz.     

Pseudomorphic In/sub 0.52/Al/sub 0.48/As/In/sub 0.7/Ga/sub 0.3/As HEMTs with an ultrahigh f/sub T/ of 562 GHz

We fabricated decananometer-gate pseudomorphic In/sub 0.52/Al/sub 0.48/As/In/sub 0.7/Ga/sub 0.3/As high-electron mobility transistors (HEMTs) with a very short gate-channel distance. We obtained a cutoff frequency f/sub T/ of 562 GHz for a 25-nm-gate HEMT. This f/sub T/ is the highest value ever reported for any transistor. The ultrahigh f/sub T/ of our HEMT can be explained by an enhanced electron velocity under the gate, which was a result of reducing the gate-channel distance.