Long wavelength vertical-cavity semiconductor optical amplifiers

This paper overviews the properties and possible applications of long wavelength vertical-cavity semiconductor optical amplifiers (VCSOAs). A VCSOA operating in the 1.3-μm wavelength region is presented. The device was fabricated using wafer bonding; it was optically pumped and operated in reflection mode. The reflectivity of the VCSOA top mirror was varied in the characterization of the device. Results are presented for 13 and 12 top mirror periods. By reducing the top mirror reflectivity, the amplifier gain, optical bandwidth, and saturation output power were simultaneously improved. For the case of 12 top mirror periods, rye demonstrate 13-dB fiber-to-fiber gain, 0.6 nm (100 GHz) optical bandwidth, a saturation output power of -3.5 dBm and a noise figure of 8.3 dB. The switching properties of the VCSOA are also briefly investigated. By modulating the pump laser, we have obtained a 46-dB extinction ratio in the output power, with the maximum output power corresponding to 7-dB fiber-to-fiber gain. All results are for continuous wave operation at room temperature     

1.3-μm vertical-cavity amplifier

We demonstrate the first 1.3-μm vertical-cavity optical amplifier. The amplifier was optically pumped and operated in reflection mode. Optimization of the top mirror reflectivity resulted in a 9.4-dB continuous wave fiber-to-fiber gain, a gain-bandwidth product of 220 GHz, and a saturation output power of -6.1 dBm, all at room temperature. By modulating the pump source, an extinction ratio of 27 dB in the output signal power was obtained     

Fabrication and characterization of 1 550 nm polarization-insensitive semiconductor optical amplifiers

Semiconductor Optical Amplifiers (SOAs) can beused asin-line amplifier ,preamplifier ,optical switch,andwavelength converter in future optical systems[1-3].Po-larization-independent gain,high output power and lowgain ripple are desirable features for most…     

High-gain, high-power 1550-nm polarization independent MQW optical amplifier

A practical 1550-nm polarization independent semiconductor optical amplifier configuration employing compressively strained quantum wells and a few commercially available optical components is reported. Crosstalk from counter propagating light, which may easily occur in such a configuration, has been sufficiently suppressed for practical use. For the entire configuration a net fiber-to-fiber gain of 17 dB, a 3-dB saturation output power of 13 dBm and a noise figure of 9 dB have been demonstrated. The polarization dependence was only 0.7 dB. The polarization independent 1550-nm semiconductor optical amplifier reported here is attractive when power consumption and compactness are of major concern and especially for applications involving nonlinear signal processing and switching.     

Acceleration of gain recovery in semiconductor optical amplifiersby optical injection near transparency wavelength

By using optical injection near the transparency wavelength of semiconductor optical amplifiers, we show experimentally that both the saturation output power and the gain recovery can be greatly improved. By injecting 80 mW of pump power, we observe a 3-dB increase in saturation output power. For 73 mW of pump power, we find a reduction in gain recovery time from over 200 ps down to below 40 ps, while maintaining 14 dB of fiber-to-fiber gain at 1555-nm wavelength     

High-gain mode-adapted semiconductor optical amplifier with12.4-dBm saturation output power at 1550 nm

A mode-adapted semiconductor optical amplifier (SOA) has been fabricated and packaged. At the gain peak, 1500 nm, the fiber to fiber gain was measured to be 32.5 dB. Statistics for eight packaged devices indicate that a fiber-to-fiber gain of 26.3 dB ± 1.3 dB and a saturation output power of 12.4 dBm ± 0.4 dBm are typical at a bias of 500 mA for λ = 1550 nm. Polarization sensitivity at 1550 nm was measured to be 1.1 dB ± 0.4 dB and the transverse electric (TE) polarization state noise figure (NF) was determined to be 7.0 dB ± 0.5 dB. The coupling loss was 1.3 dB ± 0.1 dB per facet. This SOA, with a 1.3-nm filter, was used as an optical preamplifier in a 10-Gb/s return-to-zero (RZ) system testbed with a pseudorandom binary sequence (PRBS) of 2³¹ -1. A 14.5-dB improvement in receiver sensitivity was observed at a bit error rate (BER) of 10^-11     

Optical preamplifier using antireflection-coating-free semiconductor optical amplifier with signal-inverted ASE

We fabricated an antireflection (AR)-coating-free semiconductor optical amplifier (SOA) with an absorbing region for an optical preamplifier. In the fabricated SOA, the resonance of light was fully suppressed so that the amplitude of the ripple of amplified spontaneous emission (ASE) spectra was as small as 0.36 dB, which is comparable to conventional SOAs with AR coating at both facets. We formed an optical preamplifier using the AR-coating-free SOA. The gain saturation of the SOA gives us the signal conversion to ASE and the amplification of the signal. The small-signal fiber-to-fiber and chip gain of the preamplifier were 11.4 and 20.0 dB, respectively. The 3-dB optical gain bandwidth of the preamplifier was about 30 nm.     

Facet reflectivity of a spot-size-converter integratedsemiconductor optical amplifier

Traveling-wave type semiconductor optical amplifiers (SOAs) integrated with a spot-size-converter (SSC) are extensively studied for improvement of coupling efficiency with single-mode fibers and for cost reduction in packaging. In this paper, the structural dependence of the SSC on effective facet reflectivity R_eff is investigated theoretically and experimentally. It is shown that, not only sufficient mode-conversion in the SSC region, but also the introduction of angled facets, are essential for reducing R_eff. A small gain ripple (less than 0.1 dB) in an amplified spontaneous emission (ASE) spectrum, fiber-to-fiber gain of 26 dB, and saturation output power of 7 dBm are observed for the fabricated SOA, which consists of a window length of 20 μm, facet angle of 7°, and anti-reflection coated facet of less than 1% reflectivity     

High-gain, high-power 1.3 μm compressive strained MQW opticalamplifier

A high-gain and high-saturation output power optical amplifier operating in the 1.3-μm wavelength region that was fabricated using a compressive-strained multiple-quantum-well active region is described. It is shown that optical gain as high as 27 dB and 3-dB saturation output power as high as 14 dBm were obtained simultaneously     

A single-stage three-terminal heterojunction bipolar transistoroptoelectronic mixer

A high-conversion gain three-terminal heterojunction bipolar transistor (HBT) optoelectronic mixer has been demonstrated. The maximum obtained intrinsic conversion gain was 10.4 dB. The mixing performance was measured as a function of the dc bias of the device and local oscillator power level. A SPICE-based large signal model was employed to simulate the device. The main nonlinear effects which contributed to the mixing process were the voltage dependence of the dynamic emitter resistance, and the variation of the current gain in the saturation regime     

基于76.2 mm圆片工艺的GaN HEMT可靠性评估

报道了利用76.2 mm圆片工艺实现了SiC衬底GaN HEMT微波功率管的研制,并对其进行了多项试验以评估其可靠性.器件工艺中通过引入难熔金属作器件肖特基势垒,有效提高了GaN HEMT器件肖特基势垒的热稳定性,经过500℃高温处理30 s后器件肖特基特性依然保持稳定.随后的高温工作寿命试验表明,该GaNHEMT能够...     

Gain saturation properties of a polarization insensitivesemiconductor amplifier implemented with tensile and compressive strainquantum wells

The gain saturation properties of a 1.3 μm polarization insensitive semiconductor amplifier implemented with tensile and compressive strain quantum well active region are experimentally investigated in order to determine how well the amplifier maintains its polarization insensitivity in the saturation regime. The amplifier has unsaturated gain of 12 dB and in the saturation regime the maximum observed gain imbalance between TE and TM gains is 0.9 dB. The measured 3 dB saturation output power is 5 mW     

L-band erbium-doped fibre amplifier with clamped- and flattened-gain using FBG

A gain clamped long wavelength band erbium-doped fibre amplifier (L-band EDFA) based on a ring laser cavity is demonstrated using a fibre Bragg grating (FBG) at the output end of the amplifier. This new design provides a good gain clamping as well as a gain flattening. The gain is clamped at 16.9 dB with gain variation of less than 0.1 dB from input signal power of -40 to -18 dBm by setting the VOA=5 dB. Also, the amplifier has the flattest gain spectrum at VOA=5. The gain variation is less than 1.0 dB within the wavelength range from 1570 to 1600 nm. This gain clamped amplifier also can support a 12 channel WDM system.     

128 line photonic switching system using LiNbO3 switchmatrices and semiconductor traveling wave amplifiers

The possibility of a 128-line photonic space division switching system incorporating LiNbO₃ switch matrices and semiconductor traveling wave amplifiers (TWAs) is discussed. System design is considered in terms of the most suitable location for the TWA devices that gives the most practical power margin. Design requirements for a 128-line photonic switching system suitable for a small-sized private branch exchange requirement are presented along with experimental results. It has been shown that a five-stage switch cascade, suitable for such a high-capacity switching system with a power margin of greater than 5 dB in the highest switch loss situation is possible, using low-facet-reflection TWAs. Such TWA devices have been developed in the 1.3-μm wavelength region with maximum fiber-to-fiber gain values of 15 dB. With maximum gain-polarization dependencies of 3 dB, switch losses can be compensated even under TM mode operation     

Characteristics of AlGaAs Fabry-Perot cavity type laser amplifiers

Signal gain, saturation power, and noise bandwidth, which are important parameters determining preamplifier and linear repeater system performance [1], were measured for an AlGaAs Fabry-Perot cavity type laser amplifier. The unsaturated signal gain increases with the pumping level and a maximum signal gain as high as 27 dB is obtained near oscillation threshold. The saturation output power, at which the signal gain is decreased from the unsaturated value by 3 dB, is -6 to -8 dBm. The beat noise powers between signal and spontaneous emission components were measured. The error rate characteristics of an AlGaAs laser preamplifier and Si photodiode scheme were studied at a data rate of 100 Mbits/s. The experimental results on noise powers and error rate performance are in reasonable agreement with the theoretical analysis given in an accompanying paper [1].     

High-power 1.5-/spl mu/m InGaAsP-InP slab-coupled optical waveguide amplifier

We report the first demonstration of a high-power semiconductor optical amplifier (SOA) based on the slab-coupled optical waveguide concept. This concept allows the realization of SOAs having large fundamental optical modes, low loss, and small optical confinement factor. These attributes support large output saturation power, long length for efficient heat removal, and direct butt-coupling to single-mode fibers. The 1.5-/spl mu/m InGaAsP-InP quantum-well amplifier described here has a length of 1 cm, 1/e/sup 2/ intensity widths of 4 /spl mu/m (vertical) and 8 /spl mu/m (horizontal), a fiber-to-fiber gain of 13 dB, and a fiber-coupled output saturation power of 630 mW (+28 dBm). The measured butt-coupling efficiency between the amplifier and SMF-28 is 55%. Thus, the output saturation power of the amplifier itself is approximately 1.1 W (+31 dBm).     

基于氮化铝技术的表贴型微波封装

采用氮化铝多层布线技术,运用垂直过渡方式实现微波信号从基板底部到表面的信号传输,完成表贴式微波封装设计。在DC-18GHz内,该表贴互连反射损耗小于-15dB,插入损耗小于1.0dB。采用该技术封装了6～18GHz宽带放大器,封装尺寸为5mm×5mm×1.2mm,频带内反射损耗小于-10dB,增益15dB,平坦度小于1dB;另外还封装C波段5W功率放大器,封装尺寸为8mm×8mm×1.2mm,带内增益大于25dB,反射损耗小于-10dB,饱和输出功率37dBm,效率35%。采用技术的表面贴装放大器性能上能够满足微波通信、雷达应用,可用回流焊安装,适合规模生产。     

1.55 mu m polarization-insensitive high-gain tensile-strained-barrier MQW optical amplifier

A polarization-insensitive semiconductor optical amplifier was realized at a wavelength of 1.55 mu m. The active layer consisted of a tensile-strained-barrier multiple quantum well (MQW) structure. At a driving current of 150 mA, no dependence of the saturation characteristics on modes was obtained. The saturation output power at which the gain decreases 3 dB is 13.3 dBm. A slightly higher saturation output power of 14 dBm was measured at a driving current of 200 mA. No large difference was observed between transverse-electric (TE) and transverse-magnetic (TM) modes. A high gain of 27.5 dB at a polarization sensitivity of 0.5 dB and a high saturation output of 14 dBm were realized simultaneously by using a longer device with reduced residual facet reflectivities.<>     

A 2.4-GHz 0.18-/spl mu/m CMOS self-biased cascode power amplifier

A two-stage self-biased cascode power amplifier in 0.18-/spl mu/m CMOS process for Class-1 Bluetooth application is presented. The power amplifier provides 23-dBm output power with a power-added efficiency (PAE) of 42% at 2.4 GHz. It has a small signal gain of 38 dB and a large signal gain of 31 dB at saturation. This is the highest gain reported for a two-stage design in CMOS at the 0.8-2.4-GHz frequency range. A novel self-biasing and bootstrapping technique is presented that relaxes the restriction due to hot carrier degradation in power amplifiers and alleviates the need to use thick-oxide transistors that have poor RF performance compared with the standard transistors available in the same process. The power amplifier shows no performance degradation after ten days of continuous operation under maximum output power at 2.4-V supply. It is demonstrated that a sliding bias technique can be used to both significantly improve the PAE at mid-power range and linearize the power amplifier. By using the sliding bias technique, the PAE at 16 dBm is increased from 6% to 19%, and the gain variation over the entire power range is reduced from 7 to 0.6 dB.     

1.5 µm GaInAsP traveling-wave semiconductor laser amplifier

This paper presents a theoretical and experimental study in terms of small-signal gain, signal gain saturation, and noise characteristics of a 1.5 μm GaInAsP traveling-wave amplifier (TWA), realized through the application of SiOxfilm antireflection coatings. This TWA, having a residual facet reflectivity of 0.04 percent, exhibits a wide, flat signal gain spectrum and a saturation output power of +7 dBm at a 20 dB signal gain. The TWA also has a noise figure of 5.2 dB, which is the smallest value reported for semiconductor laser amplifiers. The experimental results are confirmed to be in good agreement with the theoretical predictions based on the multimode traveling-wave rate equations in conjunction with the photon statistic master equation analysis, which takes into account the amplifier material and device structural parameters. Signal gain undulation, saturation output power, and noise figure are also theoretically evaluated as functions of the facet reflectivity. The superior performance of the TWA demonstrates that the device is favorable for use in linear optical repeaters in fiber transmission systems.