Performance of A prioritized non-blocking switch under hotspot traffic conditions with head of line resolution

In this paper, we pursue a performance analysis under hotspot traffic conditions of a four-level prioritized non-blocking baseband switch for use on board a switching multibeam satellite. Both finite input and output buffering as well as speed-up are employed to reduce the loss which is critical in a satellite application. In addition, in order to improve the performance of the two lowest priority users a head of line resolution (HLR) technique is implemented. It is shown that with HLR and the proper adjustment of the switch speed-up and the input and output buffers the loss can be substantially reduced. It is also shown that the dependence on the switch size which is characteristic of the unbuffered discard case is substantially reduced, even in a prioritized environment, allowing larger switches to be implemented.     

Architecture design,performance analysis and VLSI implementation of a reconfigurable shared buffer for high‐speed switch/router

Modern switches and routers require massive storage space to buffer packets. This becomes more significant as link speed increases and switch size grows. From the memory technology perspective, while DRAM is a good choice to meet capacity requirement, the access time causes problems for high‐speed applications. On the other hand, though SRAM is faster, it is more costly and does not have high storage density. The SRAM/DRAM hybrid architecture provides a good solution to meet both capacity and speed requirements. From the switch design and network traffic perspective, to minimize packet loss, the buffering space allocated for each switch port is normally based on the worst‐case scenario, which is usually huge. However, under normal traffic load conditions, the buffer utilization for such configuration is very low. Therefore, we propose a reconfigurable buffer‐sharing scheme that can dynamically adjust the buffering space for each port according to the traffic patterns and buffer saturation status. The target is to achieve high performance and improve buffer utilization, while not posing much constraint on the buffer speed. In this paper, we study the performance of the proposed buffer‐sharing scheme by both a numerical model and extensive simulations under uniform and non‐uniform traffic conditions. We also present the architecture design and VLSI implementation of the proposed reconfigurable shared buffer using the 0.18 µm CMOS technology. Our results manifest that the proposed architecture can always achieve high performance and provide much flexibility for the high‐speed packet switches to adapt to various traffic patterns. Furthermore, it can be easily integrated into the functionality of port controllers of modern switches and routers. Copyright © 2008 John Wiley & Sons, Ltd.     

Cell loss analysis and design trade-offs of nonblocking ATMswitches with nonuniform traffic

In practical ATM switch design, a proper dimensioning of buffer sizes and a cost effective selection of speed-up factor should be considered to guarantee a specified cell loss requirement for a given traffic. Although a larger speed-up factor provides better throughput for the switch, increasing the speed-up factor involves greater complexity and cost. Hence, it may not be cost effective to increase the speed-up factor for 100% throughput. Moreover, with a given buffer budget, an increase in the speed-up factor beyond a certain value only adds to the cell loss. The paper addresses design trade-offs existing between finite input/output buffer sizes and speed-up factor in a nonblocking ATM switch. Another important issue is the adverse effect on cell loss performance caused by nonuniform traffic (different traffic intensity and unevenly distributed routing). The paper analyzes cell loss performance of ATM switches with nonuniform traffic, and examines the effect of each nonuniform traffic parameter. The authors also provide an algorithm for effective buffer sharing that alleviates the performance degradation caused by traffic nonuniformity     

A buffer management scheme for the SCOQ switch under nonuniformtraffic loading

The SCOQ switch is a Batcher-banyan based high performance fast packet switch with shared concentration and output queueing, with a maximum of L(相似文献   

A fast parallel-tree switch architecture for ATM networks

In this paper we present a novel fast packet switch architecture based on Banyan interconnection networks, called parallel-tree Banyan switch fabric (PTBSF). It consists of parallel Banyans (multiple outlets) arranged in a tree topology. The packets enter at the topmost Banyan. Internal conflicts are eliminated by using a conflict-free 3 × 4 switching element which distributes conflicting cells over different Banyans. Thus, cell loss may occur only at the lowest Banyan. Increasing the number of Banyans leads to a noticeable decrease in cell loss rate. The switch can be engineered to provide arbitrarily high throughput and low cell loss rate without the use of input buffering or cell pre-processing. The performance of the switch is evaluated analytically under uniform traffic load and by simulation, under a variety of asynchronous transfer mode (ATM) traffic loads. Compared to other proposed architectures, the switch exhibited stable and excellent performance with respect to cell loss and switching delay for all studied conditions as required by ATM traffic sources. The advantages of PTBSF are modularity, regularity, self-routing, low processing overhead, high throughput and robustness, under a variety of ATM traffic conditions. © 1998 John Wiley & Sons, Ltd.     

Design of a non-blocking shared-memory copy network for ATM

The design of a copy network is presented for use in an ATM (asynchronous transfer mode) switch supporting BISDN (broadband integrated services digital network) traffic. Inherent traffic characteristics of BISDN services require ATM switches to handle bursty traffic with multicast connections. In typical ATM switch designs a copy network is used to replicate multicast cells before being forwarded to a point-to-point routeing network. In such designs, a single multicast cell enters the switch and is replicated once for each multicast connection. Each copy is forwarded to the routeing network with a unique destination address and is routed to the appropriate output port. Non-blocking copy networks permit multiple cells to be multicasted at once, up to the number of outputs of the copy network. Another critical feature of ATM switch design is the location of buffers for the temporary storage of transmitted cells. Buffering is required when multiple cells require a common switch resource for transmission. Typically, one cell is granted the resource and is transmitted while the remaining cells are buffered. Current switch designs associate discrete buffers with individual switch resources. Discrete buffering is not efficient for bursty traffic as traffic bursts can overflow individual switch buffers and result in dropped cells, while other buffers are under-used. A new non-blocking copy network is presented in this paper with a shared-memory input buffer. Blocked cells from any switch input are stored in a single shared input buffer. The copy network consists of three banyan networks and shared-memory queues. The design is scalable for large numbers of inputs due to low hardware complexity, O (N log₂ N), and distributed operation and control. It is shown in a simulation study that a switch incorporating the shared-memory copy network has increased throughput and lower buffer requirements to maintain low packet loss probability when compared to a switch with a discrete buffer copy network.     

Performances of the Data Vortex switch architecture under nonuniform and bursty traffic

The Data Vortex switch architecture has been proposed as a scalable low-latency interconnection fabric for optical packet switches. This self-routed hierarchical architecture employs synchronous timing and distributed traffic-control signaling to eliminate optical buffering and to reduce the required routing logic, greatly facilitating a photonic implementation. In previous work, we have shown the efficient scalability of the architecture under uniform and random traffic conditions while maintaining high throughput and low-latency performance. This paper reports on the performance of the Data Vortex architecture under nonuniform and bursty traffic conditions. The results show that the switch architecture performs well under modest nonuniform traffic, but an excessive degree of nonuniformity will severely limit the scalability. As long as a modest degree of asymmetry between the number of input and output ports is provided, the Data Vortex switch is shown to handle very bursty traffic with little performance degradation.     

Performance of two-stage shared fiber delay line optical packet switch under bursty traffic

Packet contention is a major issue in an optical packet switching network. It is not a trivial task to resolve contention due to lack of optical RAM technology. This article proposes a two-stage shared fiber delay line (FDL) optical packet switch for contention resolution. In this article, shared FDLs are used to buffer optical packets, in which a pool of buffer memory is shared among all switch output ports. Most of the existing optical buffering schemes are output-based which require a huge number of FDLs as well as a larger switch size that incur extra implementation cost. However, a shared buffering approach is considered in this article in order to reduce implementation cost. In this article, FDLs are implemented in two stages using an extremely simple auxiliary switch. The proposed switch architecture leads to more efficient use of buffer space. The superiority of the proposed switch architecture has been established by means of extensive simulations. The performance of the proposed switch is investigated under bursty traffic. Simulation result shows that the proposed switch can achieve satisfactory performance at the price of a reasonable amount of FDLs. Moreover, the significance of the proposed switch is confirmed by simulation.     

一种新型负载均衡交叉缓冲交换矩阵(英文)

The fast growth of Internet has created the need for high-speed switches. Recently, the crosspoint-queue switch has attracted attention because of its scalability and high performance. However, the Crosspoint-Queue switch does not perform well under non-uniform traffic. To overcome this limitation, the Load-Balanced Crosspoint-Queued switch architecture has been proposed. In this architecture, a load-balance stage is placed ahead of the Crosspoint-Queued stage. The load-balance stage transforms the incoming non-uniform traffic into nearly uniform traffic at the input port of the second stage. To avoid out-of-order cells, this stage employs flow-based queues in each crosspoint buffer. Analysis and simulation results reveal that under non-uniform traffic, this new switch architecture achieves a delay performance similar to that of the Output-Queued switch without the need for internal acceleration. In addition, its throughput is much better than that of the pure crosspoint-queued switch. Finally, it can achieve the same packet loss rate as the crosspoint-queue switch, while using a buffer size that is only 65% of that used by the crosspoint-queue switch.     

一种新型的负载均衡-交叉点缓冲交换结构

针对混合输入-交叉点队列(CICQ)交换结构受限于"流控通信延时"、"需要2倍内部加速仿真输出队列(OQ)交换"以及单纯交叉点缓冲(CQ)存在"非均衡流量模式下吞吐量性能不足"等问题,本文提出一种新型的"负载均衡交叉点缓冲交换结构".采用固定模式时隙轮转匹配进行负载均衡处理,将到达输入端口的非均衡流量转化为近似均衡流量并且平均分配到同一输出端口对应的交叉缓冲中,从而可以利用较小的交叉点缓冲来模拟输出队列调度,简化调度过程并且提高吞吐量.理论分析证明了这种新结构的稳定性以及模拟输出队列交换的能力.同时仿真表明,采用该交换结构可以在不需要内部加速的条件下获得相当于输出队列交换的性能,并且有效地解决了交叉点缓冲队列非均衡流量性能不足的问题.     

Architectures and Buffering for All-Optical Packet-Switched Cross-Connects

This paper considers the performance of an all-optical packet-switched cross-connect. All-optical header processing and all-optical routing are implemented in the cross-connect architectures. The main metric considered to measure the performance is the packet loss ratio for the buffering. This is influenced primarily by three factors. The first is the cross-connect architecture: feedback or feed-forward buffering, incorporating wavelength domain contention resolution. The second is the selection of the fibre delay line distribution: degenerate or non-degenerate distributions. And the third is the traffic load together with the traffic model used for the performance analysis: a Poisson distribution or a self-similar model. It is shown that the optimal implementation of a feedback buffer requires a technique such as overflow buffering as well as the superior performance of an all-optical switch in order to maintain signal quality through multiple recirculations.     

An analytical approach to the performance evaluation of the balanced gamma switch under multicast traffic

This paper presents the performance evaluation of a new cell‐based multicast switch for broadband communications. Using distributed control and a modular design, the balanced gamma (BG) switch features high performance for unicast, multicast and combined traffic under both random and bursty conditions. Although it has buffers on input and output ports, the multicast BG switch follows predominantly an output‐buffered architecture. The performance is evaluated under uniform and non‐uniform traffic conditions in terms of cell loss ratio and cell delay. An analytical model is presented to analyse the performance of the multicast BG switch under multicast random traffic and used to verify simulation results. The delay performance under multicast bursty traffic is compared with those from an ideal pure output‐buffered multicast switch to demonstrate how close its performance is to that of the ideal but impractical switch. Performance comparisons with other published switches are also studied through simulation for non‐uniform and bursty traffic. It is shown that the multicast BG switch achieves a performance close to that of the ideal switch while keeping hardware complexity reasonable. Copyright © 2006 John Wiley & Sons, Ltd.     

一种基于Credit的变长分组并行交换网络调度算法

该文提出了一种新的并行分组交换(PPS)网络调度算法。该算法通过在解复用器处采用以变长分组为业务分配单元的方式消除了信元的乱序问题;通过采用Credit机制进行业务分配,实现了业务到各个交换平面完全公平的分配;各个并行交换单元采用组合输入输出排队,降低了对缓存和交换平面的加速要求,同时可以充分利用现有单Crossbar网络调度算法的研究成果。文中证明了该算法对业务分配的公平性,对高速缓存的需求量以及整个网络的稳定性,仿真进一步证明了该算法具有良好性能。     

A self-routing multistage switching network for broadband ISDN

A switching network that approaches a maximum throughput of 100% as buffering is increased is proposed. This self-routing switching network consists of simple 2×2 switching elements, distributors, and buffers located between stages and in the output ports. The proposed switching requires a speedup factor of two. The structure and the operation of the switching network are described, and its performance is analyzed. The switch has log₂N stages that move packets in a store-and-forward fashion, incurring a latency of log₂ N time periods. The performance analysis of the switch under uniform traffic pattern shows that the additional delay is small, and a maximum throughput of 100% is achieved as buffering is increased     

An approximate analysis of shared‐buffer channel‐grouped ATM switches under imbalanced traffic

Grouping output channels in a shared‐buffer ATM switch has shown to provide great saving in buffer space and better throughput under uniform traffic. However, uniform traffic does not represent a realistic view of traffic patterns in real systems. In this paper, we extend the queuing analysis of shared‐buffer channel‐grouped (SBCG) ATM switches under imbalanced traffic, as it better represent real‐life situations. The study focuses on the impact of the grouping factor and other key switch design parameters on the performance of such switches as compared to the unichannel allocation scheme in terms of cell loss probability, throughput, mean cell delay and buffer occupancy. Numerical results from both the analytical model and simulation are presented, and the accuracy of the analysis is presented. Copyright © 2005 John Wiley & Sons, Ltd.     

Design and implementation of a scalable switch architecture for efficient high‐speed data multicasting

This paper presents the design and implementation of a new scalable cell‐based multicast switch fabric for broadband communications. Using distributed control and modular design, the multicast balanced gamma switch features a scalable, high performance architecture for unicast, multicast and combined traffic under both uniform and non‐uniform traffic conditions. The important design characteristic of the switch is that a distributed cell replication function for multicast cells is integrated into the functionality of the switch element with the self‐routing and contention resolution functions. Thus, no dedicated copy network is required. In the paper, we discuss in detail the design issues associated with the multicast functionality of the switch using 0.18 µm CMOS technology and discuss the scalability of the switch in terms of architectural, implementation, and performance scalability. Synthesized results are provided for measures of circuit complexity and timing. Copyright © 2006 John Wiley & Sons, Ltd.     

The helical switch: a multipath ATM switch which preserves cellsequence

The paper presents a new cell switching architecture for ATM-based networks. The proposed helical switch is a multistage interconnection network which implements the self-routing technique with efficient buffer sharing. Although the switch may route cells along multiple paths, the connection-oriented mode required by the ATM-based network is supported. Cell sequence integrity is guaranteed by introducing a virtual helix which forces cells routed along different paths to proceed in order and fill the internal buffers uniformly. The performance of the helical switch is investigated under uniform and nonuniform traffic patterns. Unlike single-path multistage networks such as buffered banyan networks which can degrade significantly under nonuniform traffic, the helical switch is shown to be quite robust with respect to nonuniform traffic conditions     

A multistage ATM switch with interstage buffers

Asynchronous transfer mode (ATM) is the transport technique for the broadband ISDN recommended by CCITT (I.121). Many switches have been proposed to accommodate the ATM that requires fast packet switching capability.^1-8 The proposed switches for the broadband ISDN can be classified as being of input queueing or output queueing type. Those of the input queueing type have a throughput performance which is approximately 58 per cent that of the output queueing type. However, output queueing networks require larger amounts of hardware than input queueing networks. In this paper, we propose a new multistage switch with internal buffering that approaches a maximum throughput of 100 per cent as the buffering is increased. The switch is capable of broadcasting and self-routeing. It consists of two switching planes which consist of packet processors, 2 x 2 switching elements, distributors and buffers located between stages and in the output ports. The internal data rate of the proposed switch is the same as that of the arriving information stream. In this sense, the switch does not require speed-up. The switch has log₂ N stages that forward packets in a store-and-forward fashion, thus incurring a latency of log₂ N time periods. Performance analysis shows that the additional delay is small.     

The knockout switch under nonuniform traffic

The knockout switch is a nonblocking, high-performance switch suitable for broadband packet switching. It allows packet losses, but the probability of a packet loss can be kept extremely small in a cost-effective way. The performance of the knockout switch was analyzed under uniform traffic. In this paper, we present a new, more general analytic model of the knockout switch, which enables us to evaluate the knockout switch under nonuniform traffic. The new model also incorporates the effects of a concentrator and a shared buffer on the packet loss probability. Numerical results for nonuniform traffic patterns of interest are presented     

SCOQ: a fast packet switch with shared concentration and outputqueueing

A space-division, nonblocking packet switch with data concentration and output buffering is proposed. The performance of the switch is evaluated with respect to packet loss probability, the first and second moments of the equilibrium queue length and waiting time, throughput, and buffer overflow probability. Numerical results indicate that the switch exhibits very good delay-throughput performance over a wide range of input traffic. The switch compares favorably with some previously proposed switches in terms of fewer basic building elements used to attain the same degree of output buffering