Simultaneous removal and oxidation of arsenic from water by δ-MnO2 modified activated carbon

The ubiquitous arsenic in groundwater poses a great risk to human health due to its environmental toxicity and carcinogenicity. In the present work, a new adsorbent, δ-MnO₂ modified activated carbon, was prepared, and its performance for the uptake of arsenate and arsenite species from aqueous solutions was investigated by batch experiments. Various techniques, including FESEM-EDX, p-XRD, XPS and BET surface area analysis, were employed to characterize the properties of the adsorbent and the arsenic adsorption mechanisms. The results showed that δ-MnO₂ covered on the surface and padded in the pores of the activated carbon. Adsorption kinetic studies revealed that approximately 90.1% and 76.8% of As(III) and As(V), respectively, were removed by the adsorbent in the first 9 hr, and adsorption achieved equilibrium within 48 hr. The maximum adsorption capacities of As(V) and As(III) at pH 4.0 calculated from Langmuir adsorption isotherms were 13.30 and 12.56 mg/g, respectively. The effect of pH on As(V) and As(III) removal was similar, and the removal efficiency significantly reduced with the increase of solution pH. Arsenite oxidation and adsorption kinetics showed that the As(V) concentration in solution due to As(III) oxidation and reductive dissolution of MnO₂ increased rapidly during the first 12 min, and then gradually decreased. Based on the XPS analysis, nearly 93.3% of As(III) had been oxidized to As(V) on the adsorbent surface and around 38.9% of Mn(IV) had been reduced to Mn(II) after As(III) adsorption. This approach provides a possible method for the purification of arsenic-contaminated groundwater.     

Removal of phosphate from wastewater using alkaline residue

Alkaline residue(AR) was found to be an efficient adsorbent for phosphate removal from wastewater. The kinetic and equilibrium of phosphate removal were investigated to evaluate the performance of modified alkaline residue. After treatment by NaOH(AR-NaOH), removal performance was significantly improved, while removal performance was almost completely lost after treatment by HCl(AR-HCl). The kinetics of the removal process by all adsorbents was well characterized by the pseudo second-order model. The Langmuir model exhibited the best correlation for AR-HCl, while AR was effectively described by Freundlich model. Both models were well fitted to AR-NaOH. The maximum adsorption capacities calculated from Langmuir equation were in following manner: AR-NaOH AR AR-HCl. Phosphate removal by alkaline residue was pH dependent process. Mechanisms for phosphate removal mainly involved adsorption and precipitation, varied with equilibrium pH of solution. For AR-HCl, the acid equilibrium pH( 6.0) was unfavorable for the formation of Ca-P precipitate, with adsorption as the key mechanism for phosphate removal. In contrast, for AR and ARNaOH, precipitation was the dominant mechanism for phosphate removal, due to the incrase on pH( 8.0) after phosphate removal. The results of both XRD and SEM analysis confirmed CaHPO4·2H2O formation after phosphate removal by AR and AR-NaOH.     

Preparation of Fe–Co based MOF-74 and its effective adsorption of arsenic from aqueous solution

To obtain a cost-effective adsorbent for the removal of arsenic in water,a novel nanostructured Fe–Co based metal organic framework(MOF-74)adsorbent was successfully prepared via a simple solvothermal method.The adsorption experiments showed that the optimal molar ratio of Fe/Co in the adsorbent was 2:1.The Fe_2Co_1MOF-74 was characterized by various techniques and the results showed that the nanoparticle diameter ranged from60 to 80 nm and the specific surface area was 147.82 m~2/g.The isotherm and kinetic parameters of arsenic removal on Fe_2Co_1MOF-74 were well-fitted by the Langmuir and pseudo-second-order models.The maximum adsorption capacities toward As(III)and As(V)were 266.52 and 292.29 mg/g,respectively.The presence of sulfate,carbonate and humic acid had no obvious effect on arsenic adsorption.However,coexisting phosphate significantly hindered the removal of arsenic,especially at high concentrations(10 mmol/L).Electrostatic interaction and hydroxyl and metal–oxygen groups played important roles in the adsorption of arsenic.Furthermore,the prepared adsorbent had stable adsorption ability after regeneration and when used in a real-water matrix.The excellent adsorption performance of Fe_2Co_1MOF-74 material makes it a potentially promising adsorbent for the removal of arsenic.     

Removal of phosphate by Fe-coordinated amino-functionalized 3D mesoporous silicates hybrid materials

Phosphate removal from aqueous waste streams is an important approach to control the eutrophication downstream bodies of water. A Fe(III) coordinated amino-functionalized silicate adsorbent for phosphate adsorption was synthesized by a post-grafting and metal cation incorporation process. The surface structure of the adsorbent was characterized by X-ray di raction, N2 adsoropion/desoprotion technique, and Fourier transform infrared spectroscopy. The experimental results showed that the adsorption equilibrium data were well fitted to the Langmuir equation. The maximum adsorption capacity of the modified silicate material was 51.8 mg/g. The kinetic data from the adsorption of phosphate were fitted to pseudo second-order model. The phosphate adsorption was highly pH dependent and the relatively high removal of phosphate fell within the pH range 3.0–6.0. The coexistence of other anions in solutions has an adverse e ect on phosphate adsorption; a decrease in adsorption capacity followed the order of exogenous anions: F?? > SO2?? 4 > NO??3 > Cl??. In addition, the adsorbed phosphate could be desorbed by NaOH solutions. This silicate adsorbent with a large adsorption capacity and relatively high selectivity could be utilized for the removal of phosphate from aqueous waste streams or in aquatic environment.     

Ethyl thiosemicarbazide intercalated organophilic calcined hydrotalcite as a potential sorbent for the removal of uranium(VI) and thorium(IV) ions from aqueous solutions

This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.     

Ciprofloxacin adsorption from aqueous solution onto chemically prepared carbon from date palm leaflets

A chemically prepared carbon was synthesized from date palm leaflets via sulphuric acid carbonization at 160℃. Adsorption of ciprofloxacin (CIP) from aqueous solution was investigated in terms of time, pH, concentration, temperature and adsorbent status (wet and dry). The equilibrium time was found to be 48 hr. The adsorption rate was enhanced by raising the temperature for both adsorbents, with adsorption data fitting a pseudo second-order model well. The activation energy, E_a, was found to be 17 kJ/mol, indicating a diffusion-controlled, physical adsorption process. The maximum adsorption was found at initial pH 6. The wet adsorbent showed faster removal with higher uptake than the dry adsorbent, with increased performance as temperature increased (25-45℃). The equilibrium data were found to fit the Langmuir model better than the Freundlich model. The thermodynamic parameters showed that the adsorption process is spontaneous and endothermic. The adsorption mechanism is mainly related to cation exchange and hydrogen bonding.     

Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health,arsenic(As) is a major global issue.In this study,an Fe-based metal-organic framework(MOF)(Materials of Institut Lavoisier:MIL-100(Fe)) which was impregnated with reduced graphene oxide(rGO) by using a simple hydrothermal method and coated with birnessitetype manganese oxide(δ-MnO_2) using the one-pot reaction process(MIL-100(Fe)/rGO/δ-MnO_2 nanocomposites) was synthesized and applied successfully in As removal.The removal efficiency was rapid,the equilibrium was achieved in 40 min and 120 min for As(Ⅲ) and As(Ⅴ),respectively,at a level of 5 mg/L.The maximum adsorption capacities of As(Ⅲ) and As(Ⅴ) at pH 2 were 192.67 mg/g and 162.07 mg/g,respectively.The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs.The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption.The adsorption mechanisms consisted of electrostatic interaction,oxidation and inner sphere surface complexation.     

Adsorption behavior of ammonium by a bioadsorbent – Boston ivy leaf powder

The adsorption behaviors of ammonium ions from aqueous solution by a novel bioadsorbent, the Boston ivy (Parthenocissus tricuspidata) leaf powder (BPTL) were investigated. The SEM images and FT-IR spectra were used to characterize BPTL. The mathematical models were used to analyze the adsorption kinetics and isotherms. The optimum pH range for ammonium adsorption by BPTL was found to be 5–10. The adsorption reached equilibrium at 14 hr, and the kinetic data were well fitted by the Logistic model. The intraparticle di usion was the main rate-controlling step of the adsorption process. The high temperature was favorable to the ammonium adsorption by BPTL, indicating that the adsorption was endothermic. The adsorption equilibrium fitted well to both the Langmuir model and Freundlich model, and the maximum monolayer adsorption capacities calculated from Langmuir model were 3.37, 5.28 and 6.59 mg N/g at 15, 25 and 35°C, respectively, which were comparable to those by reported minerals. Both the separation factor (RL) from the Langmuir model and Freundlich exponent (n) suggested that the ammonium adsorption by BPTL was favorable. Therefore, the Boston ivy leaf powder could be considered a novel bioadsorbent for ammonium removal from aqueous solution.     

Adsorptive removal of As(Ⅲ) ions from water using spent grain modified by polyacrylamide

In order to enhance the removal efficiency of As(III), a pre-oxidation process is generally applied first to convert As(III) to As(V), which may cause unwanted new contaminants. To overcome this problem, efforts were made to develop an effective way to remove As(III)directly without an oxidation step. The effect of polyacrylamide polymers(PAMs) such as anionic PAM, cationic PAM and nonionic PAM, on As(III) ion adsorption by spent grain(SG)was investigated. The physico-chemical properties of the three PAM-polymerized SGs(APSG(anionic PAM-polymerized modified spent grain), CPSG(cationic PAM-polymerized spent grain) and NPSG(nonionic PAM-polymerized spent grain)) were analyzed using Fourier transform infrared(FT-IR), scanning electron microscope(SEM) and zeta potential.Batch experimental data showed that the sequence of preferential adsorption for As(III) was APSG CPSG NPSG. Active functional groups such as amino group(NH2), carbonyl group(C_O), C–N bond of the amide group(CONH2), and hydroxyl group(O–H) were responsible for As(III) adsorption. Many tubular structures occurring on the surface of APSG possibly increase the specific surface areas and favor the adsorption of As(III) ions. A fixed-bed study was carried out by using APSG as an adsorbent for As(III) from water. Three factors such as bed height, initial concentration and flow rate were studied, and breakthrough curves of As(III) were obtained. The Adams–Bohart model was used to analyze the experimental data and the model parameters were evaluated.     

Synthesis of a novel ternary HA/Fe-Mn oxides-loaded biochar composite and its application in cadmium(II) and arsenic(V) adsorption

Cadmium (Cd) and arsenic (As) are two of the most toxic elements. However, the chemical behaviors of these two elements are different, making it challenging to utilize a single adsorbent with high adsorption capacity for both Cd(II) and As(V) removal. To solve this problem, we synthesized HA/Fe-Mn oxides-loaded biochar (HFMB), a novel ternary material, to perform this task, wherein scanning electron microscopy (SEM) combined with EDS (SEM-EDS) was used to characterize its morphological and physicochemical properties. The maximum adsorption capacity of HFMB was 67.11?mg/g for Cd(II) and 35.59?mg/g for As(V), which is much higher compared to pristine biochar (11.06?mg/g, 0?mg/g for Cd(II) and As(V), respectively). The adsorption characteristics were investigated by adsorption kinetics and the effects of the ionic strength and pH of solutions. X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FT-IR) revealed that chelation and deposition were the adsorption mechanisms that bound Cd(II) to HFMB, while ligand exchange was the adsorption mechanism that bound As(V).     

Preparation and characterization of a lipoid adsorption material and its atrazine removal performance

A novel adsorbent named lipoid adsorption material (LAM), with a hydrophobic nucleolus (triolein) and a hydrophilic membrane structure (polyamide), was synthesized to remove hydrophobic organic chemicals (HOCs) from solution. Triolein, a type of lipoid, was entrapped by the polyamide membrane through an interfacial polymerization reaction. The method of preparation and the structure of the LAM were investigated and subsequent experiments were conducted to determine the characteristics of atrazine (a type of HOC) removal from wastewater using LAM as the adsorbent. The results showed that LAM had a regular structure compared with the prepolymer, where compact particles were linked with each other and openings were present in the structure of the LAM in which the fat drops formed from triolein were entrapped. In contrast to the atrazine adsorption behavior of powdered activated carbon (PAC), LAM showed a persistent adsorption capacity for atrazine when initial concentrations of 0.57, 1.12, 8.31 and 19.01 mg/L were present, and the equilibrium time was 12 hr. Using an 8 mg/L initial concentration of atrazine as an indicator of HOCs in aqueous solution, experiments on the adsorption capacity of the LAM showed 69.3% removal within 6–12 hr contact time, which was close to the 75.5% removal of atrazine by PAC. Results indicated that LAM has two atrazine removal mechanisms, namely the bioaccumulation of atrazine by the nucleous material and physical adsorption to the LAM membrane. Bioaccumulation was the main removal mechanism.     

Arsenic removal from groundwater by acclimated sludge under autohydrogenotrophic conditions

Arsenic in the environment is attracting increasing attention due to its chronic health effects. Although arsenite(As(III)) is generally more mobile and more toxic than arsenate(As(V)), reducing As(V) to As(III) may still be a means for decontamination, because As(III) can be removed from solution by precipitation with sulfide or by adsorption or complexation with other metal sulfides. The performance of As(V) bio-reduction under autohydrogenotrophic conditions was investigated with batch experiments. The results showed that As(V) reduction was a biochemical process while both acclimated sludge and hydrogen were essential. Most of the reduced arsenic remained in a soluble form, although 20% was removed with no addition of sulfate, while 82% was removed when sulfate was reduced to sulfide. The results demonstrated that the reduced arsenic was re-sequestered in the precipitates, probably as arsenic sulfides. Kinetic analysis showed that pseudo first-order kinetics described the bio-reduction process better than pseudo second-order. In particular, the influences of pH and temperature on As(V) reduction by acclimated sludge under autohydrogenotrophic conditions and total soluble As removal were examined. The reduction process was highly sensitive to both pH and temperature, with the optimum ranges of pH 6.5–7.0 and 30–40°C respectively. Furthermore, Arrhenius modeling results for the temperature effect indicated that the As(V) reduction trend was systematic. Total soluble As removal was consistent with the trend of As(V) reduction.     

Adsorption of single and mixed haloacetonitriles on silica-based porous materials: Mechanisms and effects of porous structures

Adsorption mechanisms and the role of different porous and crystalline structures on the removal of five haloacetonitriles (HANs) over hexagonal mesoporous silica (HMS), titanium substituted mesoporous silica (Ti-HMS), rod-shaped SBA-15 and microporous zeolite NaY were investigated. In addition, the effect of pH on adsorption mechanism and selective adsorption of five HANs individually and in an equimolar mixed solution were evaluated. The results indicated that the intraparticle diffusion rate constants of the mesoporous adsorbents were higher than that of the microporous NaY. In single solute, the order of adsorption preference (highest to lowest) was mono-HANs?>?di-HANs?>?tri-HAN. However, in mixed solute, the large molecular weight of the tri-HAN and di-HANs are more easily adsorbed than the smaller molecular weight mono-HANs. Except for SBA-15, the order of adsorption capacities in mixed HANs solute was not different compared to that observed for the single HAN solute, which might be caused by the higher accessibility to the active sites due to larger pore size. The ion-dipole electrostatic interaction was likely to be the main adsorption mechanism, and was favored at high pH values due to the high negative surface charge density of the adsorbent. The molecular structure of the HANs and hydrophilic/hydrophobic nature affected the adsorption capacities and their selective adsorption from mixed solutes.     

Adsorption of naphthalene onto a high-surface-area carbon from waste ion exchange resin

A high-surface-area carbon (KC-1) was prepared from waste polystyrene-based ion exchange resin by KOH activation and used for naphthalene adsorption. The carbon exhibited a good hydrophobic nature with developed porous structure, favoring the adsorption of organic compounds. The Brunauer-Emmett-Teller surface area and total pore volume of KC-1 were 3442.2 and 1.68 cm 3 /g, respectively, which can be compared with those of KOH-activated carbons prepared from other precursors. Batch experiments were carried out to investigate the adsorption of naphthalene onto KC-1. The equilibrium data were analyzed by the Langmuir, Freundlich, and Polanyi- Manes isotherms and agreed with the Polanyi-Manes Model. The adsorption of naphthalene depended greatly on the porosity of the carbon, and the dispersive interactions between naphthalene and carbon could be relatively weak. The pH variation in aqueous solution had little effect on the adsorption process. The equilibrium time for 0.04 g/L of carbon dose was around 5 hr. Different models were used to evaluate the kinetic data and the pseudo second-order model was suitable to describe the kinetic process of naphthalene adsorption onto KC-1. Regeneration of spent carbon could be carried out effectively by alcohol treatment. The results indicated that KC-1 was a promising adsorbent for the removal of polycyclic aromatic hydrocarbons from aqueous solutions.     

Removal of antimonite and antimonate from water using Fe-based metal-organic frameworks: The relationship between framework structure and adsorption performance

We investigated the adsorption performance of five Fe-based MOFs (Fe-BTC, MIL-100(Fe), MIL-101(Fe), MIL-53(Fe) and MIL-88C(Fe)) for removal of antimonite (Sb(III)) and antimonate (Sb(V)) from water. Among these MOFs, MIL-101(Fe) exhibited the best adsorption capacities for both Sb(III) and Sb(V) (151.8 and 472.8 mg/g, respectively) which were higher than those of most adsorbents previously reported. The effect of steric hindrance was evident during Sb removal using the Fe-based MOFs, and the proper diameter of the smallest cage windows/channels should be considered an important parameter during the evaluation and selection of MOFs. Additionally, the adsorption capacities of MIL-101(Fe) for Sb(V) decreased with increasing initial pH values (from 3.0 to 8.0), while the opposite trend was observed for Sb(III). Chloride, nitrate and sulfate ions had a negligible influence on Sb(V) adsorption, while NO₃^? and SO₄^2? improved Sb(III) adsorption. This result implies that inner sphere complexes might form during both Sb(III) and Sb(V) adsorption.     

Adsorption of heavy metal ions from aqueous solution by carboxylated cellulose nanocrystals

A novel nanoadsorbent for the removal of heavy metal ions is reported.Cotton was first hydrolyzed to obtain cellulose nanocrystals(CNCs).CNCs were then chemically modified with succinic anhydride to obtain SCNCs.The sodic nanoadsorbent(NaSCNCs) was further prepared by treatment of SCNCs with saturated NaHCO 3 aqueous solution.Batch experiments were carried out with SCNCs and NaSCNCs for the removal of Pb 2+ and Cd 2+.The effects of contact time,pH,initial adsorption concentration,coexisting ions and the regeneration performance were investigated.Kinetic studies showed that the adsorption equilibrium time of Pb 2+ and Cd 2+ was reached within 150 min on SCNCs and 5 min on NaSCNCs.The adsorption capacities of Pb 2+ and Cd 2+ on SCNCs and NaSCNCs increased with increasing pH.The adsorption isotherm was well fitted by the Langmuir model.The maximum adsorption capacities of SCNCs and NaSCNCs for Pb 2+ and Cd 2+ were 367.6 mg/g,259.7 mg/g and 465.1 mg/g,344.8 mg/g,respectively.SCNCs and NaSCNCs showed high selectivity and interference resistance from coexisting ions for the adsorption of Pb 2+.NaSCNCs could be efficiently regenerated with a mild saturated NaCl solution with no loss of capacity after two recycles.The adsorption mechanisms of SCNCs and NaSCNCs were discussed.     

Sequestration of toxic Pb（II） ions by chemically treated rubber （Hevea brasiliensis ） leaf powder

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4–5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60–90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Removal of antibiotics from aqueous solution by using porous adsorbent templated from eco-friendly Pickering aqueous foams

The aqueous foam template without any solvent and only using the particles stabilizer has attracted much attention for preparation of the porous adsorbents. Herein, a novel porous adsorbent was fabricated via thermal-initiated polymerization of Pickering aqueous foams, which was stabilized by the natural sepiolite (Sep) and pine pollen, and utilized for the removal of antibiotic from aqueous solution. The stabilizing mechanism of Pickering aqueous foam of that the Sep was modified with the leaching substance from pine pollen and arranged orderly around the bubble to form a dense “shell” structure was revealed. The adsorbents possessed the hierarchical porous structure and excellent adsorption performance for antibiotic of chlorotetracycline hydrochloride (CTC) and tetracycline hydrochloride (TC). The equilibrium adsorption capacities of CTC and TC were achieved with 465.59 and 330.59 mg/g within 60 min at 25°C, respectively. The adsorption process obeyed Langmuir model and pseudo-second-order adsorption kinetic model. This work provided eco-friendly approach for fabricate porous adsorbents for wastewater treatment.     

Sequestration of toxic Pb(Ⅱ) ions by chemically treated rubber(Hevea brasiliensis) leaf powder

Rubber leaf powder(an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(Ⅱ) ions from aqueous solution was evaluated.The interactions between Pb(Ⅱ) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared(FT-IR) spectroscopy,scanning electron microscopy(SEM) coupled with X-ray energy dispersive spectroscopy(EDX).The effects of several important parameters which can affect adsorption capacity such as pH,adsorbent dosage,initial lead concentration and contact time were studied.The optimum pH range for lead adsorption was 4-5.Even at very low adsorbent dosage of 0.02 g,almost 100% of Pb(Ⅱ) ions(23 mg/L) could be removed.The adsorption capacity was also dependent on lead concentration and contact time,and relatively a short period of time(60-90 min) was required to reach equilibrium.The equilibrium data were analyzed with Langmuir,Freundlich and Dubinin-Radushkevich isotherms.Based on Langmuir model,the maximum adsorption capacity of lead was 95.3 mg/g.Three kinetic models including pseudo first-order,pseudo second-order and Boyd were used to analyze the lead adsorption process,and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.