UV/H2O2工艺降解环丙沙星的研究

采用UV/₂O₂工艺去除水体中的喹诺酮类抗生素环丙沙星（CIP）。考察了溶液pH值、₂O₂投加量以及水体基质对环丙沙星降解效率的影响，分析了降解产物的生成情况。研究表明，环丙沙星的降解符合拟一级反应动力学模型。降解速率受溶液pH值的影响，酸性及中性条件，有利于环丙沙星的降解。₂O₂投加量的增大，使得降解速率逐渐增大，但速率增幅逐渐变缓；最佳₂O₂/环丙沙星摩尔比为2 000。实际水体中存在的NOM、NO^-₃，促进了单独UV作用下，环丙沙星的降解。水体中的?OH焠灭剂，抑制了UV/₂O₂联合作用下，环丙沙星的降解；实际水体中的光解速率常数低于超纯水中的光解速率常数。GC-MS分析表明，UV/₂O₂工艺，使环丙沙星氧化降解生成氨基乙酸、丙二酸、丙三醇和对苯二甲酸等小分子有机物。     

溶液中阴离子对UV/H2O2降解十二烷基苯磺酸钠的影响及其机理

研究了UV/H2O2工艺对十二烷基苯磺酸钠(LAS)的去除效果、溶液中阴离子对LAS降解的影响及机理.结果表明:UV/H2O2工艺可以有效地去除水中的LAS;在H2O2投加量为8 mg/L,14 W低压汞灯照射下,LAS在蒸馏水和自来水中的反应速率常数分别为0.018 0 、0.012 2 min-1;NO-3、Cl-、SO2-4和HCO-3对LAS光降解有抑制作用,当该4种离子摩尔浓度均分别为5、10、15 mmol/L时,对LAS光降解的抑制程度为HCO-3》NO-3》Cl-》SO2-4,且随着离子摩尔浓度的增大,抑制作用增强;LAS在自来水中的反应速率常数低于在蒸馏水中的反应速率常数是由于水中多种离子影响的结果.     

UV/H2O2/草酸铁络合物光降解邻苯二甲酸二丁酯研究

研究了邻苯二甲酸二丁酯(DBP)在UV/H2O2/草酸铁络合物体系中的光降解.结果表明,UV/H2O2/草酸铁络合物能有效地光解DBP;在pH值为4时,DBP光解速率最快,中性和碱性条件下光解效率降低;DBP的光解速率随H2O2浓度的升高而增大,但H2O2浓度较大时,其对·OH的清除作用使DBP的光解速率减慢;[Fe3 ]/[C2O42]＜1/10,DBP光解速率随Fe3 浓度增大明显提高,[Fe3 ]/[C2O42]＞1/10时,引起DBP光解速率的增加不明显.     

O3/H2O2/UV降解1,2,4-三氯苯的研究

采用O3/H2O2/UV工艺处理1,2,4-三氯苯(TCB)模拟废水,考察了TCB初始浓度、pH、H2O2投加量及O3转化率等因素对O3/H2O2/UV降解TCB的影响,推断了TCB可能的降解途径。结果表明:(1)H2O2、O3、UV、O3/H2O2、O3/H2O2/UV 5种体系对TCB的降解效果为H2O2相似文献   

溶液中阴离子和腐殖酸对UV/H2O2降解2,4-二氯酚的影响

研究了UV/H2O2工艺对2,4-二氯酚(2,4-DCP)的去除效果和水中阴离子、腐殖酸对该工艺降解2,4-DCP的影响.结果表明:UV/H2O2工艺可以有效地去除水中2,4-DCP,光降解过程符合一级反应动力学模型;在H2O2投加量为8 mg/L、1个30 W低压汞灯照射下,2,4-DCP在蒸馏水和自来水中反应速率常数分别为0.023 2、0.016 2 min-1;NO-3、Cl-、HCO-3对2,4-DCP光降解有抑制作用,当3种阴离子摩尔浓度为0.5、10.0、20.0 mmol/L时,对2,4-DCP光降解的抑制程度为HCO-3＞NO-3＞Cl-;腐殖酸在低浓度时,促进光降解反应进行,在高浓度时,2,4-DCP的光降解受到抑制.自来水中的反应速率常数低于蒸馏水中的反应速率常数是由于水中多种阴离子和腐殖酸影响的结果.     

UV/TiO2光催化降解水体中的邻苯二甲酸二甲酯

酞酸酯是环境中普遍存在的有机污染物(内分泌干扰物)之一。利用UV/TiO2光催化降解水体中的邻苯二甲酸二甲酯(DMP),讨论了溶液pH、TiO2投加量及DMP初始浓度等因素对DMP降解的影响。结果表明,DMP为10mg/L左右时,TiO2投加量为0.2～0.5g/L、pH=7是比较理想的降解条件;DMP初始浓度越高,其降解率则越低。研究了Langmuir-Hinshelwood模式下DMP在TiO2表面的吸附与催化活性的关系,发现DMP主要通过吸附在催化剂的表面而非在溶液本体中发生降解。线性回归计算所得光照条件下的吸附常数远大于无光照条件下的吸附常数,可能是由于UV和TiO2体系之间产生协同效应,提高了UV/TiO2体系对DMP的降解效果。另外,初步分析了可能的降解反应机制。     

UV/Fenton法处理酸性红B研究

采用UV/Fenton高级氧化技术对酸性红B模拟废水进行处理,当进水浓度为400mg/L时,确定了各影响因素的最佳投加量:H2O2投加量为2 mL/L,Fe2 投加量为0.08g/L,最佳pH值为4;并采用一级动力学公式对酸性红B降解速率进行拟合,研究了反应条件对速率常数的影响.最后通过对单独UV法、单独Fenton法和UV/Fenton法3种处理方法效果的比较,发现UV与Fenton试剂具有协同作用.     

3种不同工艺中莠灭净的去除特性及自由基鉴定

以三嗪类除草剂莠灭净(AMT)为目标污染物,对比研究了紫外(UV)、紫外激活过硫酸盐(UV/PS)与紫外激活过一氧硫酸氢盐(UV/PMS)3种不同工艺对AMT的去除效果以及反应动力学模型。考察了底物初始浓度、氧化剂浓度、溶液初始pH和水中腐殖酸浓度对AMT降解的影响,并对反应中生成的主要自由基进行鉴定。结果表明,3种系统下AMT降解均符合拟一级反应动力学模型(R~2≥0.93)。AMT在3种不同系统下降解效率基本遵循UV/PSUV/PMSUV规律。随着底物初始浓度的增加,AMT降解率减小,拟一级速率常数kobs减小;增加氧化剂的投加量可以促进AMT降解;溶液pH的改变对UV系统下AMT的降解影响较小,而在UV/PS系统下,随着pH的增大降解率逐渐减小,在UV/PMS系统中降解率则呈现先减小后增大的趋势;投加腐殖酸会抑制AMT的降解;pH为7时,UV/PS和UV/PMS系统中反应生成的自由基主要是·SO_4~-。     

UV/H_2O_2降解水中磺胺嘧啶影响因素及机理

利用UV/H_2O_2光氧化反应器降解水中的磺胺嘧啶,考察了H_2O_2投量、pH值、紫外功率等因素对去除效果的影响,同时对反应动力学及降解产物进行了分析。结果表明,在紫外辐照与H_2O_2氧化共同作用下,UV/H_2O_2降解水中磺胺嘧啶效果显著,去除率达90%以上,其降解过程符合一级反应动力学模型(R2=0.991 2)。H_2O_2投量与磺胺嘧啶降解速率常数具有良好的线性关系,H_2O_2投量由0.03增大至1.50 mmol·L-1,反应速率常数由0.048 2增大至0.359 9 min-1;同时,随着紫外灯功率由5增大至15 W,反应速率常数由0.066 2增大至0.163 1 min-1;随着初始磺胺嘧啶浓度由0.02增加至0.08 mmol·L-1,反应速率常数由0.251 7逐渐降低至0.046 8 min-1;pH由3.0升高至7.0,反应速率常数由0.070 2增大至0.102 3 min-1,当pH继续增大时,反应速率常数反而降低。根据液相色谱/质谱(LC/MS)对中间产物分析,UV/H_2O_2降解磺胺嘧啶生成质荷比(m/z)为173、186和200的对氨基苯磺酸等中间产物,推测S—N键和C—N键被打开,这些中间产物可进一步被降解,但TOC去除率仅为7%,表明磺胺嘧啶仅部分被矿化。UV/H_2O_2工艺处理磺胺嘧啶的电能效率(EEO)采用每一对数减少级电能输入进行评价,优化条件下电能效率为0.078 k Wh·m-3,可为实际工程应用提供参考。     

TiO2/H2O2/UV和TiO2/O3/UV降解对氯苯甲酸和喹啉的试验研究

主要叙述TiO2/H2O2/UV和TiO2/O3/UV体系降解对氯苯甲酸（4-CBA）和喹啉的试验研究.研究表明,（1）在TiO2/H2O2/UV体系里目标物降解速度先随过氧化氢投加量的增加而提高,但超过一定浓度之后便开始下降;（2）在TiO2/O3/UV体系中,目标降解物的反应速度都非常快,且臭氧浓度高的时候降解速度更快;（3）二氧化钛催化剂在TiO2/O3/UV体系中作为积极因素有助于提高反应速率,而在TiO2/H2O2/UV体系是消极因素,会降低反应速率.     

Biological assessment of bisphenol A degradation in water following direct photolysis and UV advanced oxidation

Endocrine disrupting compounds (EDCs) are exogenous environmental chemicals that can interfere with normal hormone function and present a potential threat to both environmental and human health. The fate, distribution and degradation of EDCs is a subject of considerable investigation. To date, several studies have demonstrated that conventional water treatment processes are ineffective for removal of most EDCs and in some instances produce multiple unknown transformation products. In this study we have investigated the use of direct photolysis with low-pressure (LP) Hg UV lamps and UV+hydrogen peroxide (H(2)O(2)) advanced oxidation process (AOP) for the degradation of a prototypic endocrine disrupter, bisphenol A (BPA), in laboratory water. Removal rates of BPA and formation of degradation products were determined by high performance liquid chromatography (HPLC) analysis. Changes in estrogenic activity were evaluated using both in vitro yeast estrogen screen (YES) and in vivo vitellogenin (VTG) assays with Japanese medaka fish (Oryzias latipes). Our results demonstrate that UV alone did not effectively degrade BPA. However, UV in combination with H(2)O(2) significantly removed BPA parent compound and aqueous estrogenic activity in vitro and in vivo. Removal rates of in vivo estrogenic activity were significantly lower than those observed in vitro, demonstrating differential sensitivities of these bioassays and that certain UV/AOP metabolites may retain estrogenic activity. Furthermore, the UV/H(2)O(2) AOP was effective for reducing larval lethality in treated BPA solutions, suggesting BPA degradation occurred and that the degradation process did not result in the production of acutely toxic intermediates.     

光催化降解水体异味物质2-MIB的机理

以水体异味物质2-甲基异莰醇(2-methylisoborneol,2-MIB)为研究对象,在紫外光(λ<380 nm)照射下,探讨TiO2(P25)对2-MIB的光催化降解特性及光化学作用机理。结果表明,UV/TiO2光催化体系可以有效去除水体异味物质2-MIB,紫外光照射60 min,对2-MIB的降解率达95%。同时研究了光催化降解体系介质pH,共存腐殖酸(HA)和过硫酸钾(K2S2O8)对UV/TiO2光催化体系降解2-MIB的影响,发现低浓度HA([HA]≤0.5 mg/L)可以提高2-MIB降解速率,当HA浓度高于0.5 mg/L,2-MIB降解反应受到抑制;同时当加入电子受体K2S2O8后,降解体系中活性物种羟基自由基(.OH)明显增加,提高了TiO2对2-MIB的降解能力。利用苯甲酸荧光光度法和POD-DPD显色法跟踪测定降解过程中羟基自由基(·OH)和过氧化氢(H2O2)的变化,表明光催化反应涉及·OH机理。     

Photochemical degradation and mineralization of 4-chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Since the intermediate products of some compounds can be more toxic and/or refractory than the original compund itself, the development of innovative oxidation technologies which are capable of transforming such compounds into harmless end products, is gaining more importance every day. Advanced oxidation processes are one of these technologies. However, it is necessary to optimize the reaction conditions for these technologies in order to be cost-effective. OBJECTIVE: The main objectives of this study were to see if complete mineralization of 4-chlorophenol with AOPs was possible using low pressure mercury vapour lamps, to make a comparison of different AOPs, to observe the effect of the existence of other ions on degradation efficiency and to optimize reaction conditions. METHODS: In this study, photochemical advanced oxidation processes (AOPs) utilizing the combinations of UV, UV/H2O2 and UV/H2O2/Fe2+ (photo-Fenton process) were investigated in labscale experiments for the degradation and mineralization of 4-chlorophenol. Evaluations were based on the reduction of 4-chlorophenol and total organic carbon. The major parameters investigated were the initial 4-chlorophenol concentration, pH, hydrogen peroxide and iron doses and the effect of the presence of radical scavengers. RESULTS AND DISCUSSION: It was observed that the 4-chlorophenol degradation efficiency decreased with increasing concentration and was independent of the initial solution pH in the UV process. 4-chlorophenol oxidation efficiency for an initial concentration of 100 mgl(-1) was around 89% after 300 min of irradiation in the UV process and no mineralization was achieved. The efficiency increased to > 99% with the UV/H2O2 process in 60 min of irradiation, although mineralization efficiency was still around 75% after 300 min of reaction time. Although the H2O2/4-CP molar ratio was kept constant, increasing initial 4-chlorophenol concentration decreased the treatment efficiency. It was observed that basic pHs were favourable in the UV/H2O2 process. The results showed that the photo-Fenton process was the most effective treatment process under acidic conditions. Complete disappearance of 100 mgl(-1) of 4-chlorophenol was achieved in 2.5 min and almost complete mineralization (96%) was also possible after only 45 min of irradiation. The efficiency was negatively affected from H2O2 in the UV/H2O2 process and Fe2+ in the photo-Fenton process over a certain concentration. The highest negative effect was observed with solutions containing PO4 triple ions. Required reaction times for complete disappearance of 100 mgl(-1) 4-chlorophenol increased from 2.5 min for an ion-free solution to 30 min for solutions containing 100 mgl(-1) PO4 triple ion and from 45 min to more than 240 min for complete mineralization. The photodegradation of 4-chlorophenol was found to follow the first-order law. CONCLUSION: The results of this study showed that UV irradiation alone can degrade 4-CP, although at very slow rates, but cannot mineralize the compound. The addition of hydrogen peroxide to the system, the so-called UV/H2O2 process, significantly enhances the 4-CP degradation rate, but still requires relatively long reaction periods for complete mineralization. The photo-Fenton process, the combination of homogeneous systems of UV/H2O2/Fe2+ compounds, produces the highest photochemical elimination rate of 4-CP and complete mineralization is possible to achieve in quite shorter reaction periods when compared with the UV/H2O2 process. RECOMMENDATIONS AND OUTLOOK: It is more cost effective to use these processes for only purposes such as toxicity reduction, enhancement of biodegradability, decolorization and micropollutant removal. However the most important point is the optimization of the reaction conditions for the process of concern. In such a case, AOPs can be used in combination with a biological treatment systems as a pre- or post treatment unit providing the cheapest treatment option. The AOP applied, for instance, can be used for toxicity reduction and the biological unit for chemical oxygen demand (COD) removal.     

Photochemical degradation of ciprofloxacin in UV and UV/H2O2 process: kinetics, parameters, and products

Photochemical degradation of fluoroquinolone ciprofloxacin (CIP) in water by UV and UV/H₂O₂ were investigated. The degradation rate of CIP was affected by pH, H₂O₂ dosage, as well as the presence of other inorganic components. The optimized pH value and H₂O₂ concentration were 7.0 and 5 mM. Carbonate and nitrate both impeded CIP degradation. According to liquid chromatography–tandem mass spectrometry analysis, four and 16 products were identified in UV and UV/H₂O₂ system, respectively. Proposed degradation pathways suggest that reactions including the piperazinyl substituent, quinolone moiety, and cyclopropyl group lead to the photochemical degradation of CIP. Toxicity of products assessed by Vibrio qinghaiensis demonstrated that UV/H₂O₂ process was more capable on controlling the toxicity of intermediates in CIP degradation than UV process.     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理，考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响，确定出O3氧化反应的最佳工艺参数为：接触时间40min，溶液pH8．5，反应温度25℃，此条件下废水COD及UV254的去除率最高可达47．14％和73．47％；H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高，但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明，单纯采用COD作为评价指标，并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

Oxidation of MCPA and 2,4-D by UV radiation, ozone, and the combinations UV/H2O2 and O3/H2O2

The phenoxyalkyl acid derivative herbicides MCPA (4-chloro 2-methylphenoxyacetic acid) and 2,4-D (2,4-dichlorophenoxyacetic acid) were oxidized in ultrapure water by means of a monochromatic UV irradiation and by ozone, as well as by the combinations UV/H2O2 and O3/H2O2. In the direct photolysis of MCPA, the quantum yield at 20 degrees C was directly evaluated and a value of 0.150 mol Eins(-1) was obtained in the pH range 5-9, while a lower value of 0.41 x 10(-2) mol Eins(-1) was determined at pH=3. Similarly, for 2,4-D a value of 0.81 x 10(-2) mol Eins(-1) was deduced, independent of the pH of work. The influence of the additional presence of hydrogen peroxide was established in the combined process UV/H2O2, and the specific contribution of the radical pathway to the global photo-degradation was evaluated. The oxidation by ozone and by the combination O3/H2O2 was also studied, with the determination of the rate constants for the reactions of both herbicides with ozone and hydroxyl radicals at 20 degrees C. These rate constants for the direct reactions with ozone were 47.7 and 21.9 M(-1) s(-1) for MCPA and 2,4-D respectively, while the found values for the rate constants corresponding to the radical reactions were 6.6 x 10(9) and 5.1 x 10(9) M(-1) s(-1).     

O3/H2O2处理嘧啶废水的研究

采用O3/H2O2法对嘧啶废水进行处理,考察了不同反应条件对嘧啶和COD去除率的影响,并对O3/H2O2降解嘧啶的反应机制和动力学进行了初步探讨。实验结果表明,在pH值为11,反应时间为70 min,O3流量为4 g/h,H2O2投加量为50 mmol/L的条件下,废水的嘧啶和COD的去除率分别达到86.46%和74.97%。嘧啶的去除率随自由基抑制剂叔丁醇增加而降低,说明O3/H2O2降解嘧啶主要为体系中.OH的贡献。同时动力学研究表明,O3/H2O2对嘧啶的降解符合一级反应动力学模型。     

3种染料化合物在UV-TiO2/H2O2和UV-TiO2体系中的光催化降解研究

采用自制的TiO2膜和平板式固定床型光催化氧化反应装置,对甲基橙、茜素红和罗丹明B 3种含有不同生色基团的染料化合物进行了TiO2光催化氧化降解研究,通过对照测定降解过程中吸光度、电导率、pH的变化,分析了在加入和不加入H2O22种情况下降解过程的异同,比较了3种染料化合物脱色的难易程度,揭示了降解产物中无机离子的变化规律及某些可能的产物类型.