含盐量对餐厨垃圾干式厌氧发酵的影响

在中温(35℃)和高温(55℃)条件下,研究了不同含盐量(质量分数分别为0、1%、2%、3%、4%、5%)对餐厨垃圾干式厌氧发酵过程中日产气量、累积产气量、总固体(TS)、挥发性固体(VS)、沼气成分的影响。结果表明,在中温和高温条件下,当含盐量为3%(质量分数)时累积产气量均达到最高值,分别为1 244、1 419mL。此时,TS、VS的去除率也最高,中温时的去除率分别为43.2%、45.6%,高温时的去除率分别为48.3%、50.9%。餐厨垃圾干式厌氧发酵过程中沼气的甲烷含量逐渐升高,第28天时达到最高;含盐量为3%时中温和高温厌氧发酵条件下甲烷含量最高,分别为78.7%(体积分数,下同)、90.0%。     

含油量对餐厨垃圾厌氧发酵的影响

在35℃条件下，研究了不同含油量（0％、1％、2％、3％、4％、5％）餐厨垃圾中温厌氧消化过程中日产气量、甲烷含量、总固体（TS）、挥发性固体（VS）、干物质产气率等的变化，为后续餐厨垃圾连续发酵的预处理提供参考。结果表明：5％含油量餐厨厌氧发酵周期最长，累计产气量最大，为5800mL。在消化过程中，沼气中甲烷含量先上升后下降，最高可达76％；于物质产气率随含油量增大而增大，依次为497．4、506．1、543．8、554．4、590．7和600．1mL／gTS；5％含油餐厨垃圾的TS和VS去除率最大，分别为34．4％和42．9％。     

城市餐厨垃圾前处理的工艺优化

为提高餐厨垃圾资源化,利用自动化分选设备组合处理餐厨垃圾,考察餐厨垃圾快速减量化和资源化的可行性,对自动化分选前后餐厨垃圾成分进行分析,发现分选前其总量为243.05 t·d~(-1),TS为12.69%,VS为93.26%,分选后总量为242.00 t·d~(-1),TS为10.97%,VS为91.93%,其有机物含量稳定,利于厌氧发酵处理的工艺控制;对分选后餐厨垃圾进行厌氧发酵处理,考察其pH和NH_4~+-N变化,发现反应初期pH值出现弱酸性,NH_4~+-N浓度较低;随着反应进行,pH稳定在7.6~7.8,NH_4~+-N浓度约为1 200 mg·L~(-1)左右。最后对厌氧发酵产气量进行考察发现,反应前期受到pH、NH_4~+-N以及温度等反应条件影响,产气量和甲烷含量较低;随着实验趋于稳定,产气量为22 000 m3·d~(-1)左右,甲烷含量范围在65%~72%。结果表明,使用新型餐厨垃圾预处理设备,其分选效率较高,能提高后续厌氧发酵产气量和甲烷含量,较大程度实现餐厨垃圾资源化。     

接种比对餐厨垃圾干式厌氧发酵启动的影响

针对不同接种比对餐厨垃圾干式厌氧发酵启动的影响,对比分析了VS接种比分别为0.36和0.90两种情况下,餐厨垃圾干式厌氧发酵启动过程中pH、NH4-N、COD、VFA、甲烷含量等指标的变化。实验结果表明,启动初期2组样品pH分别快速降至4.74和5.68,均呈酸化状态,经碱液调整后,接种比为0.36的处理仍无法正常产气,接种比为0.90的处理,pH逐步提高,系统正常运行,经72 d的发酵实验,COD去除率达90.29%,甲烷含量高于60%的沼气产量达255.4 L,分析可见,VS接种比是干式厌氧发酵处理的重要参数;此外,与传统湿式厌氧发酵处理相比,餐厨垃圾干式厌氧发酵在较高的VFA和氨氮浓度下,仍能正常运行,采用干式厌氧发酵技术处理餐厨垃圾是可行的。     

餐厨垃圾与活性污泥混合厌氧发酵研究

为实现固体废弃物的能源化利用,对餐厨垃圾与污水处理厂活性污泥进行混合厌氧发酵,通过单因素实验考察了餐厨垃圾与活性污泥的物料配比、TS质量分数、接种量及温度等因素对产气性能的影响,在此基础上利用正交实验探索多因素共同作用对混合厌氧发酵产气特性及产甲烷量的影响。结果表明,多因素对累积产甲烷量的影响顺序为接种量TS质量分数温度物料配比,混合厌氧发酵的最佳条件为物料配比4∶6(质量比)、TS质量分数6%、接种量55%(质量分数)、温度40℃。三次函数可以用于模拟最佳条件下混合厌氧发酵过程中日产甲烷量与发酵时间的关系,模型拟合效果较好(P0.001),达到极显著水平,R~2为0.832,拟合结果可靠性高。     

城市生活垃圾和污水处理厂剩余污泥混合发酵的原料配比优化研究

以城市生活垃圾和污水处理厂的剩余污泥为混合原料,研究了混合原料的不同配比对厌氧发酵过程及产气的影响。结果表明:城市生活垃圾与剩余污泥以挥发性固体(VS)质量比为2∶1混合后,厌氧发酵效果最好,累计产气量最高,达到8 721mL,发酵后的总固体(TS)、VS、COD去除率分别达43.65%、35.98%、47.88%;各实验组在发酵过程中的pH、氨氮浓度和碱度均在合理范围内,未对厌氧发酵反应造成影响;以适当配比的城市生活垃圾和剩余污泥为混合原料,进行中温联合厌氧发酵是可行的,联合厌氧发酵可以弥补单一原料的缺陷,在一定程度上改善厌氧发酵效果。     

餐厨垃圾高温中试两相厌氧发酵的稳定性

为了考察在高负荷条件下餐厨垃圾厌氧发酵的稳定性,采用餐厨垃圾为发酵原料,以某污水处理厂脱水污泥为接种污泥,在中试规模条件下,采用产酸相中温(35℃,0.33 m3)产甲烷相高温(55℃,1.6 m3)进行连续式发酵。结果表明,餐厨垃圾厌氧发酵的产酸相有机负荷可达29.27 kg VS·(m~3·d)~(-1),产甲烷相有机负荷为6.04 kg VS·(m3·d)-1,容积产气率平均为5.61 m3·(m~3·d)~(-1),原料产气率平均达0.913 m3·(kg VS·d)-1,甲烷浓度平均为73.07%,总菌数为2.41×109个·m L-1,产甲烷菌最高为7.08×108个·m L-1,产甲烷菌数占总菌数的29.4%。两相厌氧发酵工艺可实现餐厨垃圾高负荷条件下的稳定运行。     

初始pH和温度对餐厨垃圾厌氧发酵制氢的影响

以餐厨垃圾为发酵底物,研究不同初始p H和发酵温度对餐厨垃圾厌氧发酵制氢潜力、中间代谢产物和发酵途径的影响。结果表明,初始p H和发酵温度对餐厨垃圾厌氧发酵产氢性能及代谢途径具有显著影响,高温发酵的产氢效率优于中温发酵。55℃高温、初始p H为6时厌氧发酵产氢性能最佳,累积产气量、最大氢气含量最大,分别达到620 m L和52.45%,挥发性脂肪酸中丁酸浓度最高为6 182.96 mg·L~(-1),发酵类型以丁酸型发酵途径为主。通过初始p H和发酵温度的优化控制可以有效提高产氢微生物的底物利用效率和产氢潜能,改变厌氧发酵途径,保证厌氧发酵制氢系统高效稳定运行。     

芦苇秸秆厌氧发酵影响因素正交实验及产气潜力研究

以芦苇秸秆为发酵原料,采用正交实验法,在湿式和干式批次发酵条件下,考察了预处理方式、发酵浓度和接种量对芦苇厌氧发酵沼气产量的影响。结果表明,以Na OH预处理、接种量30%、TS浓度12%的处理发酵情况最好,在第3天即出现产气高峰,最高日产气量达2.1 L,总产气量达42.8 L。芦苇的总TS和总VS产气率分别达285.7 L·kg-1TS、402.8 L·kg-1VS,具有较高的产气潜力。根据正交实验方差分析结果,芦苇厌氧发酵的影响因素的影响程度是预处理方式发酵浓度接种量,确定芦苇厌氧发酵的最佳工艺条件为:Na OH预处理、接种量100%、发酵浓度TS 12%。     

高温干发酵对互花米草产气和结构的影响

互花米草的疯长已带来严重的环境问题,厌氧发酵提供了一种资源化的解决途径.通过渗滤床高温、干式发酵互花米草,考察其产气特性;并通过元素分析、X-ray和FT-IR分析,考察干发酵及预处理对互花米草物化性质的影响.结果表明:60 d高温干发酵互花米草,累计产气量为280.9 mL/g VS(0℃);总TS与VS去除率分别为...     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.