膜电解法从模拟酸性蚀刻废液中回收铜粉

酸性蚀刻废液是一种印制电路板制作过程中产生的强酸、高铜的工业废水,对其回收利用具有较高的经济价值。采用膜电解法处理模拟酸性蚀刻废液,在阴极区回收铜粉。研究了铜粉的形成条件,考察了阴极液铜浓度、温度和电流密度对阴极电流效率的影响。结果表明,阴极液的铜浓度在20~25 g/L,温度为45~50℃,电流密度在11~12 A/dm2,阴极的电流效率最高。随着阴极液酸度的增加,铜粉的纯度提高,但阴极电效会降低。为保证较高的铜粉纯度及阴极电效,阴极液的酸度在0.32~0.36 mol/L为宜。     

城市生活垃圾中纤维素含量测定方法优化

对传统硫酸法进行改进，建立适用于城市生活垃圾纤维素含量的测定方法。以脂肪抽提时间、硫酸浓度、水解反应温度、水解反应时间、稀释硫酸浓度、回流时间为考察因素进行6因素5水平正交实验。结果表明，测定纤维素含量的最佳条件为：脂肪抽提时间4h、硫酸浓度70％、水解反应温度30℃、水解反应时间5h、稀释硫酸浓度5％、回流时间3h。优化后纤维素测定条件RSD均小于1．69％，平均回收率98．76％，表明该方法的精度高，可靠行强。     

悬浮电解法回收废旧电子印刷线路板中的铜

以废旧电子印刷线路板中的金属铜为处理对象,采用悬浮电解法制取纯铜粉。选择了4个影响铜粉的纯度、脱落率和电流效率的因素,每个因素3个水平进行正交实验。实验结果表明,硫酸铜的浓度、氯离子的浓度和电流密度对铜粉的纯度、脱落率和电流效率有较大的影响。通过对正交实验结果的分析得出最优的电解条件,在此电解条件下可得到铜粉的纯度99.8%、脱落率99.6%和电流效率99.7%。     

用褐铁矿制备聚硅氯化硫酸铁的研究

通过正交实验研究了用盐酸、硫酸、褐铁矿和硅酸钠制备聚硅氯化硫酸铁（PSFCS）絮凝剂的工艺条件。实验结果表明，浸取时间为2.5～3 h，浸取温度为110℃，硫酸浓度为6 mol/L，盐酸浓度为3 mol/L，质量液固比为4∶1，铁的浸出率可达95.7%～96.3%。溶液中加入少量聚乙烯醇作稳定剂，亚硝酸钠作氧化催化剂。PSFCS的合成条件：Fe/Si摩尔比为2，硅酸活化pH值为2，硅酸活化时间是30～40 min，陈化时间是2～2.5 h。与聚合硫酸铁（PFS）和聚合氯化铝（PAC）比较了处理印染废水的效果，表明PSFCS具有良好的絮凝性能，COD和浊度的去除率分别可达81.4%和96.1%。     

Ti/SnO2-Sb2O3/β-PbO2阳极消毒处理医院污水

采用热分解+电沉积法制备Ti/SnO2-Sb2O3/β-PbO2作为阳极消毒处理医院污水,初步探讨其杀菌基本原理,并研究了阳极材料、电流密度、电极间距、NaCl电解质浓度对消毒效果的影响。结果表明,以Ti/SnO2-Sb2O3/β-PbO2作为阳极,碳纤维作为阴极,在电流密度为80 A/m2,消毒时间为12 min,电极间距为5 mm,不添加电解质的实验条件下,处理后出水的粪大群肠菌数小于500 cfu/L,符合污水综合排放一级标准(GB8978-1996)。     

铁阳极电凝聚处理活性黑KN-B染料废水

对铁阳极电凝聚处理活性黑KN-B染料废水过程进行了实验研究.考察了电流密度、染料溶液初始pH值、电介质浓度及种类、温度、染料浓度等因素对脱色效率的影响.结果表明,在一定实验条件下,活性黑KN-B模拟废水的脱色效率达93%;电流强度、染料浓度、电解液初始pH值及电解质的种类对染料溶液脱色效率影响显著,电解液温度、电解质的浓度对脱色效率的影响不明显;以铁为阳极的原位电凝聚处理活性黑KN-B模拟废水混凝过程中主要作用机理以吸附电性中和为主;电凝聚过程中活性黑KN-B在阴极上发生了还原反应.     

ACF电极电解处理含NaCl结晶紫染料废水的研究

以吸附结晶紫达到饱和的活性炭纤维为阳极,在NaCl介质中对初始浓度为100 mg/L的结晶紫染料废水进行了电解脱色处理。实验考察了NaCl浓度、pH值和电流密度等对溶液脱色率的影响,测定了电解时溶液中生成的游离氯浓度及不同电解时间后溶液的紫外-可见吸收光谱曲线,并对不同电解时间后溶液的归一化吸光度比值进行了计算。结果发现,溶液中所产生的游离氯的浓度随电解时间的增加快速上升,20 min时就几乎达到了最大值;在活性氯的作用下,结晶紫分子中的大π共轭体系被破坏,溶液迅速脱色;电解液中所含的NaCl浓度、电解液的pH值和电流密度等都对脱色率有影响;在一定实验条件下,初始浓度为100 mg/L的结晶紫染料废水在电解60 min后脱色率可高达99.3%。     

转底炉粉尘酸浸净化液电沉积锌

对转底炉炉灰酸浸净化液电沉积锌的工艺条件和参数进行了研究,获得的电积锌最佳电积条件与参数为:锌离子浓度50 g·L~(-1),电解液pH=2,电解温度40℃,电流密度600 A·m~(-2),骨胶浓度6 mg·L~(-1)。在最佳条件下,锌电沉积电流效率接近90%,电积出的锌表面光滑平整,其纯度可达99.9%。     

PTFE/C三相电极氧阴极还原法生产过氧化氢

设计了隔膜体系电解槽,制作了聚四氟乙烯(PTFE)/碳黑三相气体扩散电极,系统研究了隔膜、电流密度、电极间距、初始溶液酸度、电解质、空气量和时间等因素对过氧化氢累积产生浓度和电流效率的影响。结果表明,在有隔膜体系,电流密度为70 m A/cm2,电极间距为1 cm,初始p H=0.5,电解质为0.10 mol/L Na2SO4溶液,空气量为40 m L/min的条件下,电解时间1 h时过氧化氢累积浓度最高可至20 096.05 mg/L,此时对应的电流效率为63.37%。在确定的最佳条件下,进行电解液循环实验,1 h时电流效率升高到98.4%,12 h之后,过氧化氢累积浓度为46 042.43 mg/L。实验原位产生的高浓度酸性过氧化氢溶液可以直接应用于Fenton试剂。     

酸浸法提取煤矸石中Al2O3的研究

煤矸石是主要的煤系固体废物,其中Al2O3质量分数约占35％左右.以某煤矿的煤矸石为原料,通过单因素实验比较盐酸和硫酸对Al2O3的浸取率,研究各因素对Al2O3浸取率的影响,确定浸取煤矸石中Al2O3的最佳酸浸介质为硫酸.利用正交实验确定酸浸取的最佳条件为:液固比(酸溶液体积与煤矸石样品质量比)15 mL/g、硫酸摩尔浓度3 mol/L、浸取时间120min、助样比(助溶剂与煤矸石样品质量比)0.20,在此条件下硫酸对煤矸石中A12O3的浸取率可达79.6％.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.