旋转填充床中Fenton＋O3氧化降解模拟阿莫西林废水

以旋转填充床（RPB）作为反应装置，研究了Fenton工艺与Fenton＋O3工艺处理模拟阿莫西林废水的效果，考察了FeSO4·7H2O的投加量、温度、旋转床转速、液体流量及pH对C0D去除率的影响。实验表明，Fenton＋O3工艺的COD脱除率及BOD5／COD相对于Fenton工艺分别提升26．7％和140％。该工艺在pH为3、温度为25℃、液体流量30L／h、气体流量2．5L／h、转速800r／min、H2O2的投加量为1mmol／L及Fe2＋投加量为0．4mm01／L的条件下，100mg／L的模拟阿莫西林废水中COD的去除率达到57．9％，BOD5/COD从0增加到0．36，满足后续生化处理要求。     

基于Ti/SnO2阳极氧化法的典型染料废水电化学氧化规律

采用Ti／SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水，研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响；在最佳组合条件下，通过分析uV—Vis光谱以及降解过程中氮元素的存在形式，研究上述2种染料的降解规律。结果表明，在pH为3，电压20V，NaCl投加量为2．5g／L的条件下，电解30min后，直接深棕M和活性艳蓝KNR的脱色率分别达到80％和95％，60min后直接深棕M的COD去除率可达75％，活性艳蓝KNR的COD去除率达到90％；电解60min后，直接深棕M的偶氮双键完全破坏，萘环和苯环结构被逐步降解，活性艳蓝KNR溶液电解2min，其分子结构中的蒽醌共轭体系被破坏，随反应的进行，蒽醌结构逐渐被破坏，染料逐步降解。     

铁炭微电解-Fenton试剂法预处理半焦废水

采用铁炭微电解／Fenton试剂法对半焦废水进行预处理，探索材料粒径、铁炭比、废水pH、H2O2用量以及反应时间对处理效果的影响。结果表明，在铁屑粒径为5～7mm，活性炭粒径为2～3mm，铁炭体积比为1：1，微电解反应90min，进水pH为8．0～9．0，H2O2投加量为4mL／L，Fenton试剂反应90min的条件下，半焦废水COD去除率可达55％以上，B／C由处理前的0．24提高到0．43，可生化性能良好，铁炭微电解／Fenton试剂法可作为半焦废水一种有效的预处理方式。     

臭氧氧化法处理印染废水

通过印染废水处理装置的建立，详细研究在了不同的接触时间、pH、PAC／H2 O2/O3体系的氧化条件下，臭氧氧化法处理印染废水的方法，解析其氧化降解过程及氧化机理。实验结果表明，经过：PAC／H2 O2/O3氧化处理后，废水的COD去除率达73．3％，脱色率达100％，可以达标排放。     

Fe（Ⅱ）EDTA／H2O2电催化降解甲基橙模拟废水的研究

在无隔膜电解槽中，采用SPR（Ru—Ir—TiO2）为阳极，石墨为阴极，考察了Fe（Ⅱ）EDTA／H2O2电催化降解甲基橙（methylorange）模拟废水的影响，发现EDTA很大程度上促进了类电Fenton试剂对甲基橙模拟废水的降解。实验研究表明，在外加电压为5．0V，EDTA：Fe2＋=2：1（摩尔比，Fe2＋=40mmol／L），H202=48mmot／L，电解质Na2SO4=40mmol／L，废水pH值为（6．5±0．1）的条件下，降解260mg／L的甲基橙模拟废水90min，EDTA的加入可以使甲基橙模拟废水的脱色率由29．5％上升到78．4％，COD由571．429mg／L降至80mg／L，COD的降解率为86％，EDTA在此过程中既是催化剂又是反应物，可有效避免EDTA带来二次环境污染的可能性。     

微电解-Fenton深度处理制药废水影响因素与参数控制

采用铁炭微电解-Fenton联合工艺深度处理制药废水生化出水,探讨了初始pH、曝气量、反应时间等因素对微电解出水Fe2+和Fe3+变化规律、COD降解速率以及后续Fenton氧化效果的影响,为优化微电解-Fenton氧化联合工艺提出了微电解间歇加酸的理论。间歇加酸可提高微电解系统中COD降解速率和Fe2+含量,使后续Fenton氧化无需投加FeSO4·7H2O即可达到较好的COD去除效果。结果表明,当初始pH=2.5,曝气量为0.6 m3/h,间歇加酸30 min/次,微电解反应2 h,出水投加1 mL/L的H2O2进行Fenton氧化2 h,COD总去除率可达81.33%;间歇加酸30 min/次可将微电解反应2 h出水Fe2+浓度从50 mg/L提高至151 mg/L,COD降解速率从10.6 mg COD/(L·h)提高至22.2 mg COD/(L·h)。     

UV／草酸铁／H2O2法处理乙草胺废水的研究

对UV／草酸铁／H2O2法处理乙草胺废水进行研究，考察了H2O2浓度、FeSO4浓度、K2C2O4浓度、pH值及反应时间对乙草胺去除效果的影响。结果表明，当H2O2／FeSO4／K2C2O4(化学剂量数比)=50：5：1，H2O2／乙草胺初始COD(质量浓度比)=3：1时，该技术对乙草胺的去除率可达85％以上。这表明，采用UV／草酸铁／H2O2法可以有效地处理含乙草胺废水。     

复合混凝剂处理染料废水的研究

分析酸性大红染料的结构与特点，进行各种混凝剂的筛选实验，配制FeSO4—MgSO4—Ca(OH)2—PAM复合混凝剂，并通过实验优化操作条件，实验结果表明，对COD=288．3mg／L、色度为25000倍的酸性大红GR实验废水，COD去除率可高达85．3％，最高脱色率可达97．4％，在脱色率达90％时，药剂费用为1．12元／t。     

Fenton试剂法预处理发酵甘油生产提取废水

采用Fenton试剂预处理高浓度难降解发酵法甘油生产提取废水。研究了pH、Fe^2 、H2O2、反应时间和H2O2投加次数对废水COD去除效果的影响。结果表明，通过Fenton试剂氧化可使废水中的COD值从13500mg／L降至4030mg／L，COD去除率达到70．1％。废水的BOD5／COD值从0．202提高至0．568，可生化性得到较大提高，为后续处理创造了条件。研究成果为发酵法甘油生产提取废水的预处理提供了一种非常有效的方法。     

参杂负载型纳米TiO2降解橙黄G的光催化活性及其动力学研究

采用溶胶-凝胶法和浸渍-焙烧法制备了掺杂Sn（Ⅳ）的TiO2／AC光催化剂，以偶氮染料橙黄G为目标降解物，对光催化反应条件进行了优化。结果表明：利用Sn（IV）掺杂量为2．5at．％的TiO2／AC光催化剂，在进水浓度50mg／L，催化剂的用量12．5g／i，pH值2．0，H2O2 1．5mL／L。主波长为365nm的300W高压汞灯光照条件下，反应60rain，橙黄G的光催化去除率可达99．1％。该反应符合Langmuir-Hinshelwood动力学方程，其速控步为吸附反应。共存阴离子SO4^2-和H2PO4^-，对橙黄G的光催化降解反应均有一定的抑制作用。     

Electrochemical degradation applied to the metabolites of Acid Orange 7 anaerobic biotreatment

The electrochemical oxidation of the biotic degradation products of the textile dye C.I. Acid Orange 7 (AO7) was achieved using a boron doped diamond electrode (BDD). Tests were performed with model solutions of the biotic degradation products, sulphanilic acid (SA) and 1-amino-2-naphthol (AN), and also with real effluents obtained in experiments carried out in an up-flow anaerobic sludge blanket (UASB) reactor, fed with a simulated textile effluent containing AO7, working in mesophilic or thermophilic conditions. Bulk electrolysis was studied using two different supporting electrolytes - NaCl and Na(2)SO(4). The influence of initial metabolite concentration and current density on the electrodegradation rates of the biotic products was investigated. For the UASB effluents, oxidation tests were carried out for different electrolytes and at different current densities. Samples were collected at pre-selected intervals and absorbance measurements, chemical oxygen demand (COD) and total organic carbon (TOC) tests and high performance liquid chromatography (HPLC) analysis were performed. Results have shown an almost complete elimination of the persistent pollutants and a COD removal higher than 70% for both AN and SA. For the UASB effluents, COD removals between 45% and 90% and TOC removals varying from 19% to 41% were obtained.     

Fenton试剂处理电厂离子交换树脂再生废水

采用 Fenton试剂对电厂离子交换树脂再生废水进行催化氧化处理 ,实验结果表明 ,当溶液 p H=2 .0、H2 O2 ( 30 % )投加量为 6 0 m L/L、F e SO4· 7H2 O投加量为 4.5 g/L、H2 O2 投加次数为 4、反应时间为 1.5 h时 ,废水的处理效果最佳     

光催化氧化深度处理电镀有机废水的工程化实验

采用光催化氧化联用技术对电镀有机废水进行深度处理工程化实验。探讨了uV、uV＋H2O3、uV＋H2O2＋TiO2、uV＋H2O2＋FeSO4、uV＋H2O2＋FeSO4＋TiO2、uV＋O3＋TiO2和uV＋03＋TiO2＋H2O2等体系对废水有机污染物去除率的影响。结果表明，相较于其他反应体系，uV＋O3＋TiO2＋H2O2体系具有更好的氧化效果，经碳滤处理后去除率达到90％以上，最终出水水质满足GB18918-20O2-级标准（A标准）的要求。实际运行项目偿还期5．33年，NPV〉0，内部收益率大于基准值10％。研究表明，uV＋O3＋TiO2＋H2O，体系能降低加药量，工作量及运行成本。可为电镀企业实际废水处理提供现实依据，为优化电镀废水的处理工艺提供参考。     

强化UV/Fenton法降解水中苯酚的研究

研究了UV/Fenton法处理含苯酚废水时H2 O2 和FeSO4 加入量及苯酚初始浓度对酚去除效果的影响及C2 O2 -4 对UV/Fenton法的增强效果。 [H2 O2 ]=2 0mmol/L ,[FeSO4 ]=5mmol/L ,反应 2 0min ,苯酚初始浓度为 5 0mg/L时 ,酚去除率达 99%。UV/Fenton体系中引入C2 O2 -4 后可有效提高对紫外和可见光的利用率 ,进而提高了对高浓度苯酚废水去除效果     

Color and COD removal from wastewater containing Reactive Black 5 using Fenton's oxidation process

In this study, Reactive Black 5 (RB5) was removed from synthetic wastewater using Fenton's oxidation (FO) process. Experiments were conducted on the samples containing 100 and 200 mg l(-1) of RB5 to remove the dye toxicity. Seventy-five milligram per litre of RB5 caused 25% toxicity on 24-h born daphnids whereas 100 mg l(-1) of RB5 displayed 100% toxicity on Daphnia magna. The study was performed in a systematic approach searching optimum values of FeSO(4) and H(2)O(2) concentrations, pH and temperature. Optimum pH and temperature for 100 mg l(-1) of RB5 were observed as 3.0 and 40 degrees C, respectively, using 100 mg l(-1) of FeSO(4) and 400 mg l(-1) of H(2)O(2) resulted in 71% chemical oxygen demand (COD) and 99% color removal. For 200 mg l(-1) of RB5, 84% COD removal was obtained using 225 mg l(-1) of FeSO(4) and 1000 mg l(-1) of H(2)O(2) yielding 0.05 molar ratio at pH 3.0 and 40 degrees C. Color removal was also more than 99%. The optimum conditions determined in accordance with the literature data. The H(2)O(2) requirement seems to be related to initial COD of the sample. FeSO(4)/H(2)O(2) ratios found were not changed for both concentrations. The temperature affected the COD removal significantly at high degrees. Toxicity was completely removed for each concentration of RB5 at optimum removal conditions.     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理，考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响，确定出O3氧化反应的最佳工艺参数为：接触时间40min，溶液pH8．5，反应温度25℃，此条件下废水COD及UV254的去除率最高可达47．14％和73．47％；H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高，但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明，单纯采用COD作为评价指标，并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

碱催化H2O2氧化法预处理奶牛养殖废水的试验研究

采用碱催化H2O2氧化法对奶牛养殖废水进行预处理试验,研究了温度、pH、H2O2投加量、反应时间等参数对COD去除效果的影响,确定了反应最佳运行条件。试验结果表明,碱催化H2O2氧化法在pH7~12时,对COD的去除率为40%~60%;当反应温度50℃,pH值9,H2O2投加量2.72 g/L,反应时间20 min时,COD的去除率为66.3%。     

基于Ti/SnO_2阳极氧化法的典型染料废水电化学氧化规律

采用Ti/SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水,研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响;在最佳组合条件下,通过分析UV-Vis光谱以及降解过程中氮元素的存在形式,研究上述2种染料的降解规律。结果表明,在pH为3,电压20 V,NaCl投加量为2.5 g/L的条件下,电解30 min后,直接深棕M和活性艳蓝KNR的脱色率分别达到80%和95%,60 min后直接深棕M的COD去除率可达75%,活性艳蓝KNR的COD去除率达到90%;电解60 min后,直接深棕M的偶氮双键完全破坏,萘环和苯环结构被逐步降解,活性艳蓝KNR溶液电解2 min,其分子结构中的蒽醌共轭体系被破坏,随反应的进行,蒽醌结构逐渐被破坏,染料逐步降解。     

Comparison of various advanced oxidation processes and chemical treatment methods for COD and color removal from a polyester and acetate fiber dyeing effluent

In this paper, a comparison of various advanced oxidation processes (O3, O3/UV, H2O2/UV, O3/H2O2/UV, Fe2+/H2O2) and chemical treatment methods using Al2(SO4)3.18H2O, FeCl3 and FeSO4 for the chemical oxygen demand (COD) and color removal from a polyester and acetate fiber dyeing effluent is undertaken. Advanced oxidation processes (AOPs) showed a superior performance compared to conventional chemical treatment, which maximum achievable color and COD removal for the textile effluent used in this study was 50% and 60%, respectively. Although O3/H2O2/UV combination among other AOPs methods studied in this paper was found to give the best result (99% removal for COD and 96% removal for color), use of Fe2+/H2O2 seems to show a satisfactory COD and color removal performance and to be economically more viable choice for the acetate and polyester fiber dyeing effluent on the basis of 90% removal.     

Decolorization and biodegradability of photocatalytic treated azo dyes and wool textile wastewater

The photodegradation and biodegradability have been investigated for four non-biodegradable commercial azo dyes, Reactive YellowKD-3G, Reactive Red 15, Reactive Red 24, Cationic Blue X-GRL, an indicator. Methyl Orange, and one industrial wool textile wastewater, using TiO2 suspensions irradiated with a medium pressure mercury lamp. The color removal of dyes solution and dyeing wastewater reached to above 90% within 20-30 min. of photocatalytic treatment. Biochemical oxygen demand (BOD) was found to increase, while chemical oxygen demand (COD), total organic carbon (TOC) decreased, so that the ratio of BOD5/COD of the wastewater increased from original zero up to 0.75. The result implies that photocatalytic oxidation enhanced the biodegradability of the dye-containing wastewater and therefore relationship between decolorization and biodegradability exists. When the color disappeared completely, the wastewater biodegraded normally and could be discharged for further treatment. The experimental results demonstrate that it is possible to combine photocatalysis with conventional biological treatment for the remedy of wastewater containing generally non-biodegradable azo dyes.