Correlation of polychlorinated naphthalenes with polychlorinated dibenzofurans formed from waste incineration

Isomer composition of polychlorinated naphthalenes (PCNs) was measured for municipal waste incinerator fly ash samples and for emission samples produced from soot and copper-deposit experiments conducted at the United States Environmental Protection Agency (US-EPA). Two types of PCN isomer patterns were identified. One pattern contained specific PCN isomers in which chlorine atoms are substituted as if the peri(alpha-) position were dechlorinated from the higher chlorinated PCNs one by one. In another pattern, the isomers had a tendency for the chlorine atoms to assume successive positions on the naphthalene ring, which may be caused by specifically oriented chlorination. Some of these isomers increased, together with several polychlorinated dibenzofuran (PCDF) and a few polychlorinated dibenzo-p-dioxin (PCDD) isomers. The ratios between some specific PCN, PCDF, and PCDD isomers measured for the fly ash samples agree with those obtained from the soot and copper-deposit experiments. The observations suggest that these isomers were formed possibly from de novo synthesis utilizing the carbon structure contained in soot under the catalytic effect of a copper compound. Typical isomers for PCNs and PCDFs produced from incineration emissions were identified.     

Polychlorinated biphenyls and dibenzofurans retained in the tissues of a deceased patient with Yucheng in Taiwan

Various tissues from a deceased Yucheng (oil disease) patient were analyzed for individual polychlorinated biphenyl (PCB) and dibenzofuran (PCDF) congeners. With a few exceptions, PCBs with 5 or less chlorine atoms were almost completely excreted from the patient's tissues about two years after the ingestion of the toxic oil. In contrast, most PCB congeners with 6 or more chlorine atoms were retained in the tissues. The intestinal fat contains the highest level of PCBs while the liver contains the highest concentration of PCDFs. The major PCDF congeners retained in the tissues were 1,2,3,4,7,8-hexaCDF, 2,3,4,7,8-pentaCDF, and 1,2,4,7,8-pentaCDF. The former two congeners, especially 2,3,4,7,8-pentaCDF, are very toxic PCDFs; they may play important roles in the etiology of Yucheng.     

Verification of dioxin formation in a catalytic oxidizer

Emissions and inlet concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDF) have been measured from a catalytic oxidizer and a thermal oxidizer. The catalyst inlet temperature was 427 degrees C. The thermal oxidizer operating temperature was 791 degrees C. Data of the toxic dioxin and furan congeners are reported. Important results of this field study are: (1) the catalytic oxidizer in this study produced an increase in PCDD/PCDF congener concentration of almost 10-fold from the inlet to the outlet (stack), thus verifying results of a previous study that evaluated only PCDD/PCDF emissions. All congeners increased from inlet to the stack. (2) The thermal oxidizer had little effect on PCDD/PCDF levels. There was a decrease in four of the congeners and an increase in 13 congeners. (3) Ambient air was the main source of PCDD/PCDFs in the stack emissions of the thermal oxidizer in this study. Laboratory investigations are needed to understand how PCDD/PCDFs are formed (and emitted) under conditions of this study.     

Mechanism of the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans from chlorophenols in gas phase reactions

The pyrolysis of chlorinated phenates at a temperature of about 280 degrees C results in the formation of definite chlorinated dibenzodioxin (PCDD) congeners [1-3]. It is shown that in gas phase reactions chlorophenols react in the presence of oxygen above 340 degrees C not only to PCDD but also to chlorinated dibenzofurans (PCDF). The mechanism of this reaction of chlorophenols to PCDD and PCDF was elucidated. In a first step phenoxyradicals are formed which are capable of forming PCDDs and PCDFs. This is confirmed by the oxygen dependency of the reaction. In an argon atmosphere no dimerization of chlorophenols could be observed at 420 degrees C. By the identification of intermediates and by analyzing the PCDF isomers formed from individual chlorophenols the reaction pathway is elucidated. As intermediates in the formation of PCDFs polychlorinated dihydroxybiphenyls (DOHB) were identified. These are most likely formed by the dimerization of two phenoxy radicals at the hydrogen substituted carbons in ortho-positions under simultaneous movement of the hydrogen atoms to the phenolic oxygen PCDDs are formed in the gas phase via ortho-phenoxyphenols (POP) analogous to the pyrolysis of phenates, but due to the radical mechanism in the first condensation step to POPs not only a chlorine atom is capable for substitution but also the hydrogen atoms. The formation of the DOHBs and their condensation to PCDFs and hydroxylated PCDFs as well as the ratio of PCDD to PCDF formed show a strong dependency on the reaction temperature, the substitution pattern of the chlorophenols and the oxygen concentration.     

PCDD/PCDF formation in the chlor-alkali process—laboratory study and comparison with patterns from contaminated sites

Studies on the formation of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) during the electrolysis of sodium chloride solution (brine) using graphite or titanium electrodes were carried out at a laboratory scale. High concentrations of PCDFs but no PCDDs were formed in tests using graphite electrodes. With titanium electrodes, PCDFs were only formed when tar pitch was added and mainly originated from the dibenzofuran present in the tar. For the first time, a detailed assessment of the formation of mono- to octachlorinated PCDD/PCDF from tar pitch was investigated. The assessment included of the chlorination steps proved that PCDFs were formed by successive lateral chlorinated from dibenzofuran to MonoCDFs, DiCDFs, and TriCDFs to form the typical known “chlorine pattern” of TetraCDF to OctaCDF with a dominance of 1,2,7,8- and 2,3,7,8-TetraCDFs, 1,2,3,7,8-PentaCDF, and 1,2,3,4,7,8-HexaCDF as marker congeners. The final homologue distributions depended on reaction time and reaction temperature. In addition, electrolysis with non-chlorinated dibenzo-p-dioxins, dibenzofuran, and biphenyl was carried out. As a result, PCDDs, PCDFs, and PCB were formed at comparable yields. Congener patterns in soil samples from a PCDD/F-contaminated site where chlor-alkali electrolysis had been operated for decades in Japan had identical isomer distribution demonstrating the source and contamination potential and risk of these processes. Therefore, sites where in the past 120 years chlor-alkali electrolysis has been operated or where residues from chlor-alkali production or other chlorine using industries have been disposed should be assessed for their pollution level and exposure relevance. The assessment of total organohalogen content revealed that PCDF is only a small fraction of organohalogens in the contaminated soils. For an appropriate risk assessment, also other chlorinated aromatic compounds such as PCBs or PCNs need to be considered.     

Analysis of polychlorodibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs) in baked-salt food additives in Korea

Thirty-one samples of baked-salt products used in commercial food additives were analyzed for the presence of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Dioxins were highly detected in 12 samples of baked salts. The amount of dioxins found in the samples ranged from 12.47 pg/g to 406.56 pg/g (0.71 pg TEQ/g to 23.51 pg TEQ/g, respectively). The most abundant congeners, as TEQ values, were 2,3,4,7,8-PeCDF; 1,2,3,7,8-PeCDF; and 1,2,3,4,7,8-HxCDF in PCDF congeners and 1,2,3,7,8-PeCDD; 1,2,3,6,7,8-HxCDD; and 1,2,3,7,8,9-HxCDD in PCDD congeners. Meanwhile, PCDDs/PCDFs were analyzed in high-temperature-treated samples of natural sea salt alone and natural sea salt to which di-(2-ethylhexyl)phthalate (DEHP) had been added. In the former case, PCDD/PCDF formation was most evident at temperatures near 450 degrees C, the total amount of dioxins was 90.07 pg/g (6.07 pg TEQ/g), and PCDD congeners comprised less than 50% of the total PCDDs/PCDFs. However, when the latter samples were heated, the total PCDD/PCDF concentration was 512.30 pg/g (21.53 pg TEQ/g), with PCDD congeners comprising over 87% of the total PCDDs/PCDFs.     

Analysis of polychlorinated naphthalenes in environmental samples

A method for the analysis of polychlorinated naphthalenes (PCN) has been developed. It is based on a simple clean-up procedure using activated carbon and a mass fragmentographic analysis using the negative ions formed during chemical ionization (NCI). Unlike the technical PCN products we have analyzed, a few isomerides containing four to six chlorine atoms dominate the PCN pattern in the environmental samples. The levels found in samples of biota from fresh water and marine environments in Sweden were between 3 and 62 ng PCN per gram lipid.     

Formation of PCDF, PCDD, PCB, and PCN in de novo synthesis from PAH: mechanistic aspects and correlation to fluidized bed incinerators

The difference of polychlorinated dibenzofurans (PCDF) isomer patterns between stoker type incinerators and some fluidized bed incinerators (FBI) is a key to understand the formation mechanisms in both types of incinerators. The total yield and the isomer patterns of PCDF, polychlorinated biphenyls (PCB), polychlorinated naphthalenes (PCN), and polychlorinated benzenes (PCBz) formed via de novo synthesis from polycyclic aromatic hydrocarbons (PAH) indicate that chlorinated aromatics in the FBI are formed as a result of PAH breakdown. The detailed analysis of the isomer patterns of PCDF, PCB and PCN gives a first insight into the transformation mechanism of the PAHs and the sequence of degradation, chlorination and oxygen insertion. The major chlorination takes part at the position of the C-C cleavage during degradation of the PAHs. Further chlorination of the hydrogen position of the former PAH takes part preferably in ortho-position to this chlorination or is directed by incorporated oxygen. A perylene structure in soot is proposed as basis for the observed PCDF pattern in the FBI. Polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated phenols (PxCP) were formed in lower concentrations from the de novo experiments indicating an additional formation pathway for these compounds in the FBI.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in human adipose tissues of Japan

Thirteen samples of human adipose tissue from cancer patients in Japan were analyzed for tetra- to octa- chlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). These compounds were identified in all the samples analyzed. All isomers identified have a pattern of chlorine substitution in 2, 3, 7 and 8 positions with the only exception of 1,2,3,4,6,7,9-hepta-CDD. In the case of PCDFs, the relatively higher persistency was found in the isomers with chlorine atoms at 4- (or 6-) position as compared with 1- (or 9-) position. Total PCDD concentrations were in the range of 160 to 1400 pg/g on wet weight basis, in which increasing levels were found from tetra- to octa-CDD. Total PCDF concentrations were in the range of 7 to 120 pg/g and the levels of individual congeners are rather uniform.     

Formation of chlorinated phenols, dibenzo-p-dioxins, dibenzofurans, benzenes, benzoquinnones and perchloroethylenes from phenols in oxidative and copper (II) chloride-catalyzed thermal process

Formation of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and chlorinated phenols on CuCl(2) from unsubstituted phenol and three monochlorophenols was studied in a flow reactor over a temperature range of 100-425 degrees C. Heated nitrogen gas streams containing 8.0% oxygen were used as carrier gas. The 0.00024mol of unsubstituted phenol and 0.00039mol of each monochlorophenol were passed through a 1g and 1cm SiO(2) particle containing 0.5% (Cu by mass) CuCl(2). Chlorination preferentially occurred on ortho-(2, 6) and para-(4) positions. Chlorination increased up to 200 degrees C, and thereafter decreased as temperature increased. Chlorination of phenols plays an important role in the formation of the more chlorinated PCDD/Fs. Chlorinated benzenes are formed possibly from both chlorination of benzene and chlorodehydroxylation of phenols. Chlorinated phenols with ortho chlorine formed PCDD products, and major PCDD products were produced via loss of one chlorine. For PCDF formation, at least one unchlorinated ortho carbon was required.     

Distribution of PCDDs, PCDFs and dioxin-like PCBs in the blood, testis and adipose tissue of suckling beef calves

To determine the distribution of persistent organochlorine compounds in beef cattle, concentrations of 2,3,7,8-substituted PCDDs, PCDFs and dioxin-like PCBs were measured in the blood, testes and adipose tissue of four two-month-old Japanese Black calves. Of 29 congeners analyzed, 19, 20 and 28 were detected in the blood, testes and adipose tissue, respectively, of three or all calves. Total toxic equivalents (TEQs) were similar in the testes and adipose tissue, and approximately two times higher than in the blood on a lipid weight basis (P<0.05). More PCDDs and PCDFs had accumulated in the testes than in adipose tissue (P<0.01), but more dioxin-like PCBs were found in adipose tissue than in the testes (P<0.0001). Accumulation patterns in the testes and adipose tissue varied among the congeners of PCDD and PCDF, whereas the patterns were similar in dioxin-like PCBs. In particular, highly substituted PCDD congeners were detected at high concentrations in the testes but at lower concentrations in adipose tissue compared with other congeners. By contrast, accumulation levels of highly substituted PCDFs were lower in both those tissues than the other congeners. In conclusion, it was demonstrated that PCDDs, PCDFs and dioxin-like PCBs leave the circulation and accumulate in the testes and adipose tissue in bovine calves. It was suggested that congeners of PCDD, especially highly substituted PCDDs, and PCDFs have a tendency to accumulate in the testis and dioxin-like PCB congeners accumulate readily in adipose tissue.     

Low-resolution mass spectrometric relative response factors (RRFs) and relative retention times (RRTs) on two common gas chromatographic stationary phases for 87 polychlorinated dibenzofurans

All 87 tetra- to octa-chlorinated dibenzofurans (PCDFs) were analysed using high-resolution gas chromatography/low-resolution mass spectrometry (HRGC-LRMS). The mass spectrometer was operated in two different modes: electron ionisation (EI), and negative ion chemical ionisation (NCI) with methane as a reagent gas. Baseline separation and identification of all PCDF congeners was carried out using one non-polar (DB-5) and one polar (RT-2330) capillary GC column. Relative retention times (RRTs) on both columns, and relative response factors (RRFs) in both EI- and NCI-modes, were calculated for all 87 of the PCDFs. Comparison of the EI-RRFs and NCI-RRFs showed that the mass spectrometric NCI-responses varied to a higher degree than the EI-responses. The level of NCI-response was dependent on the substitution positions of the chlorine atoms on the dibenzofuran molecule skeleton. The ratio between the highest and lowest RRFs was 26 in the NCI-mode, but only 2.3 in the EI-mode. Thus, quantification of tetra- to octa-CDFs in environmental samples using the NCI-mode will result in incorrect estimates of PCDF concentrations unless 13C-labelled internal standards are used for each congener, or RRFs are taken into consideration. In contrast, the quantification of PCDFs in the EI-mode using a single internal 13C-labelled PCDF standard for each PCDF homologue is accurate according to the findings in this investigation. A flue gas sample from a municipal solid waste incinerator (MSWI) analysed in the NCI-mode was quantified with and without NCI-RRFs. When using NCI-RRFs the reported concentration of SigmaPCDFs in the flue gas sample increased by 40%. Furthermore, TCDF analysis was compared using two mass spectrometers (a VG 12-250 and a Finnigan 4500) operating in EI-mode. These quadrupole instruments performed equally well, giving similar EI-RRFs for the tested compounds.     

Persistent organic pollutants in Detroit River suspended sediments: polychlorinated dibenzo-p-dioxins and dibenzofurans,dioxin-like polychlorinated biphenyls and polychlorinated naphthalenes

Suspended sediments from the Detroit River were collected in 1999 and 2000 using sediment traps at sites ranging from western Lake Erie to southern Lake St. Clair and analyzed to determine the spatial distributions of contaminants including polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs), dioxin-like PCBs (DLPCBs) and polychlorinated naphthalenes (PCNs). Concentrations of all three contaminant classes were clearly elevated at sites in the lower reaches of the river in the Trenton Channel. The potential influence of the Trenton Channel as a source of contamination to western Lake Erie was further evidenced by PCDD/PCDF homologue profiles, which indicated a contribution from chemical manufacturing in addition to the normal background combustion profile. Toxic equivalents (TEQs) for PCDDs/PCDFs generally exceeded those for DLPCBs; combined total TEQs in July 2000 for these two compound classes ranged from 2.30 pg/g in southern Lake St. Clair to 306 pg/g at a station just downstream of the outflow of Monguagon Creek in the Trenton Channel. The spatial distribution of PCN contamination was similar to that of PCDDs/PCDFs and DLPCBs, with the highest level of total PCNs (8200 ng/g) detected at a site in the Trenton Channel near Elizabeth Park; TEQs for PCNs in the Trenton Channel ranged from 73 to 3300 pg/g. The data indicate that PCNs represent a significant contribution to dioxin-like biological activity in Detroit River suspended sediments.     

Analysis of some polyhalogenated organic pollutants in sediment and sewage sludge

A laminated sediment core collected in the southern part of the Baltic Proper was analysed for DDT compounds, polychlorinated biphenyls (PCB) including the coplanar congeners, polybrominated diphenyl ethers (PBDE) and polychlorinated naphthalenes (PCN). Two sewage sludge samples were also analysed for the same compounds.

The results of the sediment analyses indicate the presence of PCB, DDT and PBDE compounds in sediment layers dating from the 1950s and later. Neither coplanar PCB nor PCN were detected at any level of the sediment core. The PCB concentrations indicate a slight increase in levels during the last decades, while there were no changes in the levels of DDT compounds. In contrast, TeBDE levels increase 4- to 8-fold and one PeBDE congeners levels increase 10- to 20-fold. The results of sewage sludge analyses showed the concentration of the individual PBDE to be at about the same level as for the individual PCB congeners. The congener pattern in sludge samples indicates low-chlorinated products to be the main PCN source.     

Formation and chlorination of polychlorinated naphthalenes (PCNs) in the post-combustion zone during MSW combustion

Non- to octa-chlorinated naphthalenes (PCNs) were analyzed in flue gas samples collected simultaneously at three different temperatures (450 degrees C, 300 degrees C and 200 degrees C, respectively) in the post-combustion zone during waste combustion experiments using a laboratory-scale fluidized-bed reactor. PCN homologue profiles in all samples were dominated by the lower chlorinated homologues (mono- to triCN), with successive reductions in abundance with each additional degree of chlorination. The isomer distribution patterns reflected ortho-directionality behavior of the first chlorine substituent, and the beta-positions, i.e. the 2,3,6,7-substitution sites, seemed to be favored for chlorination. Injection of naphthalene into the post-combustion zone resulted in increased PCN levels at 200 degrees C, demonstrating the occurrence of chlorination reactions in the post-combustion zone. However, the increases were restricted to the least-chlorinated homologue (monoCN), probably because there was insufficient residence time for further chlorination. In addition, an episode of poor combustion (manifested by high CO levels) was accompanied by extensive formation of 1,8-diCN, 1,2,3- and 1,2,8-triCN; congeners with substitution patterns that are not thermodynamically favorable. These are believed to be products of PAH breakdown reactions and/or chlorophenol condensation. Overall, PCN formation is likely to occur via more than one pathway, including chlorination of naphthalene that is already present, de novo synthesis from PAHs and, possibly, chlorophenol condensation.     

Polychlorinated naphthalenes: an environmental update

Polychlorinated naphthalenes (PCNs; CNs) form a complex mixture of up to 75 congeners containing from one to eight chlorine atoms per naphthalene molecule. Chloronaphthalenes are widespread global environmental pollutants which accumulate in biota. All chloronaphthalenes are planar compounds and can contribute to the aryl hydrocarbon (Ah) receptor-mediated mechanism of toxicity with a combination of various 2,3,7,8-tetrachlorodibenzo-p-dioxin like toxic responses. There are three known main sources of environmental pollution with PCNs: technical PCN formulations, technical polychlorinated biphenyl formulations, and thermal and other processes in the presence of chlorine. The purpose of this paper is to briefly review the most recent data on environmental pollution, chemistry, analysis, sources, formation, persistence, toxicity and behavior of PCNs.     

Distribution of dioxins, furans, and dioxin-like PCBs in solid products generated by pyrolysis and melting of automobile shredder residues

Polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and dioxin-like polychlorinated biphenyls (PCBs) in char and slag produced from automobile shredder residue by pyrolysis and melting process were analyzed to measure changes in the characteristics and distribution of their congeners caused by thermal treatment. In particular, a large quantity of dioxin-like PCBs occurred in low-chlorinated congeners. The concentration of PCDDs/PCDFs in char was 0.542 microg/kg, with mostly PCDFs dominant and its toxicity equivalent concentration (TEQ) was about 70ngTEQ/kg. The concentration and toxicity equivalent concentration of dioxin-like PCBs in char were 0.869 microg/kg and 1.60ngTEQ/kg, respectively. Melted char slag was produced using various cooling methods: water quenching, air cooling, and slow cooling. The concentrations of PCDDs/PCDFs in slag produced by the methods were 1.51, 1.38, and 2.43ngTEQ/kg, respectively; those of dioxin-like PCBs were close to 0.01ngTEQ/kg. The congener distributions varied only slightly among the cooling methods. Applying melting procedure to char reduced PCDD/PCDF concentration by 95.3%, and the corresponding TEQ concentration was reduced by 97.9%. We thus conclude that melting process is an efficient way to reduce the concentrations of PCDDs/PCDFs in solids produced by pyrolysis.     

Effects of combustion and operating conditions on PCDD/PCDF emissions from power boilers burning salt-laden wood waste

This paper discusses the effects of combustion conditions on PCDD/PCDF emissions from pulp and paper power boilers burning salt-laden wood waste. We found no correlation between PCDD/PCDF emissions and carbon monoxide emissions. A good correlation was, however, observed between PCDD/PCDF emissions and the concentration of stack polynuclear aromatic hydrocarbons (PAHs) in the absence of TDF addition. Thus, poor combustion conditions responsible for the formation of products of incomplete combustion (PICs), such as PAHs and PCDD/PCDF precursors, increase PCDD/PCDF emissions. PAH concentrations increased with higher boiler load and/or low oxygen concentrations at the boiler exit, probably because of lower available residence times and insufficient excess air. Our findings are consistent with the current understanding that high ash carbon content generally favours heterogeneous reactions leading to either de novo synthesis of PCDD/PCDFs or their direct formation from precursors. We also found that, in grate-fired boilers, a linear increase in the grate/lower furnace temperature produces an exponential decrease in PCDD/PCDF emissions. Although the extent of this effect appears to be mill-specific, particularly at low temperatures, the results indicate that increasing the combustion temperature may decrease PCDD/PCDF emissions. It must be noted, however, that there are other variables, such as elevated ESP and stack temperatures, a high hog salt content, the presence of large amounts of PICs and a high Cl/S ratio, which contribute to higher PCDD/PCDFs emissions. Therefore, higher combustion temperatures, by themselves, will not necessarily result in low PCDD/PCDFs emissions.     

Occurrence,profile and possible sources of PCNs in Hong Kong soils,and a comparison with PCBs,PCDDs and PCDFs

Polychlorinated naphthalenes (PCNs) have been proposed for inclusion in the annexes of the Stockholm Convention by the European Union, signifying a probable increase in monitoring PCN levels at a global level. Investigations on PCN levels in the environment of Hong Kong have not been reported. In this preliminary investigation, PCN levels in surface soils samples were determined by isotope dilution HRGC/HRMS techniques, and compared with those of polychlorinated biphenyl (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). The concentrations of PCNs in the soil samples were 35–883 pg g^?1 (average, 201; and median, 94 pg g^?1), which were lower than those of PCBs PCDDs and PCDFs. This comparison suggested that PCNs are currently not priority POPs compared with dioxins and PCBs in Hong Kong soils. PCDDs were the most important contributor to the sum of toxic equivalents of PCNs, PCBs, PCDDs and PCDFs. OCDD was the most dominant dioxin congener in Hong Kong surface soils. PCB-118 was the most abundant in 12 dl-PCB congeners. PCN congeners indicating thermal related sources (CN52/60, CN66/67 and CN73) were relatively abundant in their respective homologs, which suggested PCN contamination from thermal sources. The ratio of CN73 to CN74 in soil samples suggested the contribution of PCN contaminations in soils from both thermal-related sources and evaporative emissions of technical PCN mixtures.     

Organic chlorine compounds in lake sediments. IV. Dioxins, furans and related chloroaromatic compounds

Polychlorodibenzo-p-dioxins (PCDDs), polychlorodibenzofurans (PCDFs), polychloronaphthalenes (PCNs) and coplanar PCBs were measured in surface sediments from 18 lake areas in Central Finland. Toxic 2, 3, 7, 8-substituted PCDD and PCDF congeners occurred at low levels (<20 − 230 pg/g dw). PCNs appeared at few ng/g (total PCNs) levels. Pulp mills or any other local sources could not be associated with the sedimented PCDDs, PCDFs and PCNs. Coplanar PCB congeners 77 and 105 (IUPAC Nr) were generally found at 20–550 pg/g levels. The most toxic congener 126 was measured (110 pg/g) only at one area near a local PCB leakage. Pulp mill originated aromatic chlorocompounds which coelute with PCDDs and PCDFs in clean up, probably alkyl polychlorobibenzyls (R-PCBBs) appeared at ng/g levels and showed a clear gradient dowstreams from pulp mill effluent points.