高压除鳞喷嘴内部流场数值模拟与仿真分析

针对目前工厂广泛使用的高压除鳞喷嘴,应用前处理软件Gambit建立其内部流畅的三维模型,采用Fluent软件提供的Laminar层流模型对不同结构参数的喷嘴内部不可压缩、稳态、层流流场进行了数值模拟,并分析了各参数对其流场速度分布、压力分布和出口轴心速度的影响.仿真值与理论计算值十分接近,数值模拟结果表明,喷嘴收缩角和直径对其内部流场影响较大,而扩张角对其内部流场影响相对较小,但各参数都存在最优值,且各参数之间也存在着最优搭配使射流打击效果最好.     

前混合磨料水射流除鳞喷嘴混合腔内部流场

基于计算流体动力学多相流混合物模型,应用FLUENT软件对前混合磨料水射流除鳞喷嘴高压水与磨料混合腔内部流场进行数值模拟.比较了不同进料方式对流场均匀性的影响.分析了两侧为高压水入口条件下,磨料入口直径、高压水入口直径、高压水入口位置和角度以及收缩段锥角对流场混合均匀性的影响,得到了影响混合腔内部流场混合均匀性的合理结构参数.数值计算结果表明:入口速度一定的条件下,磨料中进式喷嘴混合腔的混合均匀性优于磨料侧进式喷嘴混合腔.随磨料入口和高压水入口直径增加,混合腔出口的射流速度均增加,但随高压水入口直径增加导致出口磨料浓度呈先增后减的趋势,磨料入口与高压水入口合理的质量流量比值约为3∶4,两侧高压水入口位置对流场混合均匀性影响较小,高压水入口角度和收缩段锥角均为30°时流场性能更佳.     

空化喷嘴内部流场的数值模拟

根据喷嘴的结构特点,建立了角形空化喷嘴和风琴管形空化喷嘴的三维结构模型和数值模型,选用RNGk-ε湍流模型,采用SIMPEC算法进行数值计算。结果表明,在空化喷嘴的圆柱段存在速度最大值,射流进入圆柱段后产生明显的负压,与周围介质发生强烈的空化作用,有利于空化气泡的产生。在特定参数下(圆柱段直径d=1mm、圆柱段长度S=3mm、扩散段长度L=8mm、出口扩散角=30°),角形喷嘴的空化效果优于风琴管形喷嘴。     

前混合水射流喷丸喷嘴内流数值模拟

为研究弹丸在前混合水射流喷丸喷嘴内的运动特性,应用FLUENT软件对前混合水射流出口带圆柱段和扩散段的圆锥收敛形喷嘴内液固湍流进行了数值模拟。控制方程为连续相采用三维不可压缩稳态雷诺时均N-S方程,湍流模型采用k-ε模型,离散相采用拉格朗日模型。分析了喷嘴出口圆柱段长度、圆锥收敛角和出口扩散段对内流特性的影响。结果表明,出口圆柱段长度为30 mm、圆锥收敛角为13°时,连续相可以获得最大的轴向速度,且离散相的加速效果也最佳;出口带扩散段的喷嘴使得连续相和离散相的出口速度均会下降,但会增大喷丸的覆盖率,提高喷丸工作效率。     

基于CFD技术的喷气织机主喷嘴内部流场的分析

通过对喷气织机主喷嘴现状的分析提出了应用CFD的思路.应用NUMECA软件进行主喷嘴内部流场数值模拟,揭示了导纱管内不同截面上气流速度的分布,并对主喷嘴内部气流的轴向动压和马赫数分布进行了分析.结果表明,利用数值模拟研究主喷嘴流场特性方便、快捷,且精度也较高.     

缩放型喷嘴产生的空化射流流场数值模拟

应用Standard k-ε,RNG k-ε和Standard k-ω湍流模型对缩放型喷嘴内部湍流流场进行数值模拟,结合理论及质量流量测试试验对数值模拟结果进行对比验证.结果表明:RNG k-ε湍流模型最适合用于数值模拟缩放型喷嘴内部的湍流流场;RNG k-ε湍流模型数值模拟结果显示缩放型喷嘴收缩角使喷嘴喉管部产生了低压场,压差的产生使水射流的空化效果得到了提高.     

新型气溶性射流喷嘴设计与数值模拟

针对传统高压水射流清洗耗水量大,能耗和运营费用高、清洗后的废液需要处理才能达到环保要求的缺陷,提出了新型射流清洗方式—气溶性射流.对新型气溶性射流喷嘴进行了结构设计,得到了喷嘴混合室直径、喉部直径、出口直径、收缩段长度以及扩张段长度等关键参数,并对新型喷嘴内外气液二相流场进行了深入计算与分析.结果表明,气液二相流雾滴在喷嘴轴线上速率随气流入口压力增大而增大,在喷嘴喉部速率变化率最大,在喷嘴出口处速率达到最大;当扩散角为10°时,射流扩散较慢,内部扰动和摩擦损失较小;当收缩角为30°时,气液二相流流动性较好,能量损失较小;粒径较小雾滴沿轴线方向速率变化较大,当喷射距离为35mm时,气液二相流雾滴速率达到最大值.     

基于Fluent角型喷嘴内部空化行为的数值模拟

利用Fluent流体计算软件对角型喷嘴内部的空化流场进行了数值模拟,得到了喷嘴内部的压力、气相生成速率和汽含率分布场,并对三种扩张角喷嘴内的流场进行了比较分析.结果表明:在角型喷嘴内部,空化汽泡主要在喷嘴圆柱段壁面起始点和扩张段壁面起始点两处产生;在扩张段壁面起始点处,由于回流和压力两种因素的共同作用导致扩张角对空化汽泡生成速率的影响存在最优值;随着扩张角的减小,角型喷嘴在扩张段壁面的空化区域不断扩大,其汽含率也不断攀升;扩张角的改变对角型喷嘴圆柱段区域的空化行为没有明显影响.     

淹没条件下长圆喷嘴流场数值模拟

为了提高径向水平井扩孔效率,将长圆喷嘴引入磨料射流扩孔技术,建立射流流场的流动控制方程,结合Realizable k-ε模型对方程组进行求解,并将结果与锥形喷嘴射流结果进行对比.结果表明:长圆喷嘴射流具有一定的扩散性,且短轴剖面上的扩散角比长轴剖面上大;喷嘴内射流速度及出口速度随长宽比增大而减小,随出口直径增加而增加;在喷嘴入口速度和出口直径相同的情况下,长圆喷嘴出口速度小于锥形喷嘴;无因次喷距大于11.3时,长圆喷嘴外射流轴线速度大于锥形喷嘴的;射流出口断面宽度随喷距增大而增大,在相同条件下长圆喷嘴扩孔宽度大于锥形喷嘴,且射流具有自模性;数值计算结果与磨料射流扩孔试验结果基本吻合.     

新型后混合磨料水射流喷嘴流场均匀性分析

针对目前后混合磨料喷嘴流场不均匀性问题，利用FLUENT仿真软件，对一种新型后混合磨料水射流喷嘴内部流场进行三维数值模拟. 通过比较喷嘴内部有无圆锥挡板的内部流场，分析圆锥挡板对流场均匀性的影响. 分析不同参数圆锥挡板喷嘴的喷射效果，得出新型后混合磨料水射流喷嘴不同参数结构对内部流场均匀性的影响规律，来提高后混合磨料水射流喷嘴中水和磨料混合均匀性. 分析结果表明：在保证出口仍具有较高速度的情况下，增大缩口直径，可以降低混合腔空气压力，改善液体在腔内聚集现象. 在此基础上，向混合腔中加入二次B样条曲线形状的圆锥挡板，当磨料入口采用斜入式与喷嘴轴线成45°时，出口体积分数最接近15%，体积分数波动最小，磨料与水混合均匀性大大提高. 通过正交试验分析多参数对磨料均匀性的影响，得到最优的结构参数.     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Perspherical Approaches for Electrons in Atoms and Charged Excitons in Quantum Wells

Instead of following Fock’s expansion,we solve the Schrodinger equation for some quantum mechanical manybody systems such as electrons in atoms and charged excitons in quantum wells in a similar way in hyperspherical coordinates by expanding the wave functions into orthonormal complete basis sets of the hyperspherical hannonics(HHs)of hyperangles and generalized Laguerre polynomials(GLPs)of the hyperradius.This leads the equation to     

Advances in broadband wireless communications under high-mobility scenarios

Future mobile communication systems aim at providing very high data transmission rates, even in high-mobility scenarios such as high-speed wheel-track trains, maglev trains, highway vehicles, airplanes, guided missiles or spacecraft. A particularly important commercial application is the strong and increasing worldwide demand for high- speed broadband wireless communications （up to 574.8 km/ h test speeds or 380 km/h commercial speeds） in railways, providing data, voice and video services for applications such as onboard entertainment services to passengers, train control, train dispatch, train sensor status handling and sur- veillance. In such high-mobility scenarios, there are a number of communication challenges, including fast hand- over, location updating, high-speed channel modeling, estimation and equalization, anti-Doppler spreading tech- niques, fast power control, and dedicated network architec- ture. Because signal transmission in very high-speed scenarios will inevitably experience serious deterioration, it is imperative to develop key broadband mobile communi- cation techniques for such high-speed vehicles.     

Wuhan University Journal of Natural Sciences TOTAL CONTENTS

<正>~~     

Scale-based spatial data model for GIS

Being the primary media of geographical information and the elementary objects manipulated, almost all of maps adopt the layer-based model to represent geographic information in the existent GIS. However, it is difficult to extend the map represented in layer-based model. Furthermore, in Web-Based GIS, It is slow to transmit the spatial data for map viewing. In this paper, for solving the questions above, we have proposed a new method for representing the spatial data. That is scale-based model. In this model we represent maps in three levels: scale-view, block, and spatial object, and organize the maps in a set of map layers, named Scale-View, which associates some given scales.Lastly, a prototype Web-Based GIS using the proposed spatial data representation is described briefly.     

英文诗歌中的喻类修辞

为了有助于提高英文爱好者的个人情操、文化素养和学习兴趣,以及专业人员对英语学习和研究进行多途径的探索,本文通过一些精选诗歌的引证和分析,着重论述了喻类修辞法在英文诗歌中的运用其及效果。     

Man Is Unable to Change the Miserable Life——Analysis of the Arrangement of Four Characters in The Glass Menagerie

Tennessee Williams is considered as one of the most important American playwrights since World War II.The Glass Menagerie is his first successful drama,which describes a tragic situation of family and means to say that Man is unable to change the miserable life,no matter whatever means he try,This essay focuses on the analysis of the arrangement of the four main characters:Laura.Amanda,Jim and Tom to reveal the theme.Laura is fragile.Amanda is brave.Jim is vital.Tom is sensible.And all of them develop and try the different means to struggle against life,but fail tragically.With the evidence,the paper comes to conclusion naturally that Man is unable to change the miserable life,and he dooms to fail.     

Characterization of root-nodulating bacteria on Retama raetam in arid Tunisian soils

The aim of this study is to investigate the diversity of Retama raetam root-nodule bacteria isolated from arid regions of Tunisia. Twelve isolates, chosen as representative for different 16S rRNA gene patterns, were characterized by 16S rRNA gene sequencing and phenotypic analysis. Isolates were assigned to Sinorhizobium, Rhizobium and Agrobacterium. Symbiotic properties of Sinorhizobium and Rhizobium isolates showed a large diversity in their capacity to infect their host plant and fix atmospheric nitrogen. Strain RK 22 identified as Rhizobium was the most effective isolate.     

An Affordable Accurate Evaluation of the Binding Conformations Predicted by Molecular Docking Studies in Bio-System

正Recently,docking has been widely used to predict the binding-modes of protein-inhibitors,when the crystal complexes structure was absent.Most docking algorithms are able to generate a large number of probable conformations,it,however,is difficult to effectively evaluate these docking poses and identify the most reasonable bindingmode.In the present study,on the basis of the crystallographic data of human 3-hydroxy-3-methylglutaryl coenzyme     

WIMAX与WI-FI技术分析及联合组网

介绍了WiMAX与Wi-Fi两种无线宽带接入技术,并对两者之间的关系及相互之间的影响做了对比及分析,并对WiMAX的关键技术进行了详细说明,最后对两者的联合组网方式做了简单的探讨。