Wavelength considerations in confocal microscopy of botanical specimens

We have used a multiple-laser confocal microscope with lines at 325, 442, 488, 514 and 633 nm to investigate optical sectioning of botanical specimens over a wide range of wavelengths. The 442-nm line allowed efficient excitation of Chromomycin A3, with minimal background autofluorescence, to visualize GC-rich heterochromatin as an aid to chromosome identification. Sequential excitation with 442- and 488-nm light enabled ratio imaging of cytosolic pH using BCECF. The red HeNe laser penetrated deep into intact plant tissues, being less prone to scattering than shorter blue lines, and was also used to image fluorescent samples in reflection, prior to fluorescence measurements, to reduce photobleaching. Chromatic corrections are more important in confocal microscope optics than in conventional microscopy. Measured focus differences between blue, green and red wavelengths, for commonly used objectives, were up to half the optical section thickness for both our multi-laser system and a multi-line single-laser instrument. This limited high-resolution sectioning at visible wavelengths caused a loss in signal. For ultraviolet excitation the focus shift was much larger and had to be corrected by pre-focusing the illumination. With this system we have imaged DAPI-stained nuclei, callose in pollen tubes using Aniline Blue and the calcium probe Indo-1.     

Extending immunofluorescence detection limits in whole paraffin-embedded formalin fixed tissues using hyperspectral confocal fluorescence imaging

A major problem in microscopic imaging of ex vivo tissue sections stained with fluorescent agents (e.g. antibodies, peptides) is the confounding presence of background tissue autofluorescence. Autofluorescence limits (1) the accuracy of differentiating background signals from single and multiple fluorescence labels and (2) reliable quantification of fluorescent signals. Advanced techniques such as hyperspectral imaging and spectral unmixing can be applied to essentially remove this autofluorescent signal contribution, and this work attempts to quantify the effectiveness of autofluorescence spectral unmixing in a tumour xenograft model. Whole-specimen single-channel fluorescence images were acquired using excitation wavelengths of 488 nm (producing high autofluorescence) and 568 nm (producing negligible autofluorescence). These single-channel data sets are quantified against hyperspectral images acquired at 488 nm using a prototype whole-slide hyperspectral fluorescence scanner developed in our facility. The development and further refinement of this instrument will improve the quantification of weak fluorescent signals in fluorescence microscopy studies of ex vivo tissues in both preclinical and clinical applications.     

Spectral characterization of Dictyostelium autofluorescence

Dictyostelium discoideum is used extensively as a model organism for the study of chemotaxis. In recent years, an increasing number of studies of Dictyostelium chemotaxis have made use of fluorescence-based techniques. One of the major factors that can interfere with the application of these techniques in cells is the cellular autofluorescence. In this study, the spectral properties of Dictyostelium autofluorescence have been characterized using fluorescence microscopy. Whole cell autofluorescence spectra obtained using spectral imaging microscopy show that Dictyostelium autofluorescence covers a wavelength range from approximately 500 to 650 nm with a maximum at approximately 510 nm, and thus, potentially interferes with measurements of green fluorescent protein (GFP) fusion proteins with fluorescence microscopy techniques. Further characterization of the spatial distribution, intensity, and brightness of the autofluorescence was performed with fluorescence confocal microscopy and fluorescence fluctuation spectroscopy (FFS). The autofluorescence in both chemotaxing and nonchemotaxing cells is localized in discrete areas. The high intensity seen in cells incubated in the growth medium HG5 reduces by around 50% when incubated in buffer, and can be further reduced by around 85% by photobleaching cells for 5-7 s. The average intensity and spatial distribution of the autofluorescence do not change with long incubations in the buffer. The cellular autofluorescence has a seven times lower molecular brightness than eGFP. The influence of autofluorescence in FFS measurements can be minimized by incubating cells in buffer during the measurements, pre-bleaching, and making use of low excitation intensities. The results obtained in this study thus offer guidelines to the design of future fluorescence studies of Dictyostelium.     

Single molecule fluorescence imaging of the photoinduced conversion and bleaching behavior of the fluorescent protein Kaede

Photoconversion and photobleaching behavior of the fluorescent protein Kaede immobilized in polyacrylamide gel matrix at room temperature was studied by single molecule wide-field fluorescence microscopy. Photobleaching kinetics of Kaede molecules upon excitation at 488 nm showed slight heterogeneity, suggesting the presence of different protein conformations and/or the distribution of local environments in the gel matrix. Statistical analysis of intensity trajectories of single molecules revealed four major types of fluorescence dynamics behavior upon short illumination by a violet light pulse (405 nm). In particular, two types of photoswitching behavior were observed: the green-to-red photoconversion (4% of Kaede molecules) and the photoactivation of green fluorescence without emission of red fluorescence (13%). Two other major groups show neither photoconversion nor red emission and demonstrate photoinduced partial deactivation (43%) and partial revival (30%) of green fluorescence. The significantly lower green-to-red conversion ratio as compared with bulk measurements in aqueous solution might be induced by the immobilization of the protein molecules within a polyacrylamide gel. Contrary to Ando et al. (Proc Natl Acad Sci 2002;99:12651-12656), we found a significant increase in green fluorescence emission upon illumination with 405-nm light, which is typical for GFP and related proteins.     

Fluorescence resonance energy transfer (FRET) measurement by gradual acceptor photobleaching

Fluorescence resonance energy transfer (FRET) is an extremely effective tool to detect molecular interaction at suboptical resolutions. One of the techniques for measuring FRET is acceptor photobleaching: the increase in donor fluorescence after complete acceptor photobleaching is a measure of the FRET efficiency. However, in wide-field microscopy, complete acceptor photobleaching is difficult due to the low excitation intensities. In addition, the method is sensitive to inadvertent donor bleaching, autofluorescence and bleed-through of excitation light. In the method introduced in this paper, donor and acceptor intensities are monitored continuously during acceptor photobleaching. Subsequently, curve fitting is used to determine the FRET efficiency. The method was demonstrated on cameleon (YC2.1), a FRET-based Ca²⁺ indicator, and on a CFP-YFP fusion protein expressed in HeLa cells. FRET efficiency of cameleon in the presence of 1 mm Ca²⁺ was 31 ± 3%. In the absence of Ca²⁺ a FRET efficiency of 15 ± 2% was found. A FRET efficiency of 28% was found for the CFP-YFP fusion protein in HeLa cells. Advantages of the method are that it does not require complete acceptor photobleaching, it includes correction for spectral cross-talk, donor photobleaching and autofluorescence, and is relatively simple to use on a normal wide-field microscope.     

Digital scanned laser light-sheet fluorescence lifetime microscopy with wide-field time-gated imaging

We develop a multidimensional fluorescence imaging technique by implementing a wide-field time-gated fluorescence lifetime imaging into digital scanned laser light-sheet microscopy (FLIM-DSLM) to measure 3D fluorescence lifetime distribution in mesoscopic specimens with high resolution. This is achieved by acquiring a series of time-gated images at different relative time delays with respect of excitation pulses at different depths. The lifetime is determined for each voxel by iteratively fitting to single exponential decay. The performance of the developed system is evaluated with the measurements of a lifetime reference Rhodamine 6G solution and a subresolution fluorescent bead phantom. We also demonstrate the application performances of this system to ex vivo and in vivo imaging of Tg(kdrl:EGFP) transgenic zebrafish embryos, illustrating the lifetime differences between the GFP signal and the autofluorescence signal. The results show that FLIM-DSLM can be used for sample size up to a few millimetres and can be utilised as a powerful and robust method for biomedical research, for example as a readout of protein–protein interactions via Förster resonance energy transfer.     

Combining ocFLIM and FIDSAM reveals fast and dynamic physiological responses at subcellular resolution in living plant cells

For a deeper understanding of molecular mechanisms within cells and for the realization of predictive biology for intracellular processes at subcellular level, quantitative biology is required. Therefore, novel optical and spectroscopic technologies with quantitative and dynamic output are needed in cell biology. Here, we present a combined approach of novel one-chromophore fluorescence lifetime imaging microscopy to probe the local environment of fluorescent fusion proteins and fluorescence intensity decay shape analysis microscopy to suppress interfering autofluorescence. By applying these techniques, we are able to analyse the subcellular localization and partitioning of a green fluorescence protein fusion of the salt stress-induced protein low temperature induced (LTI)6b in great detail with high spatial and temporal resolution in living cells of Arabidopsis plants.     

Probing plasma membrane microdomains in cowpea protoplasts using lipidated GFP-fusion proteins and multimode FRET microscopy

Multimode fluorescence resonance energy transfer (FRET) microscopy was applied to study the plasma membrane organization using different lipidated green fluorescent protein (GFP)‐fusion proteins co‐expressed in cowpea protoplasts. Cyan fluorescent protein (CFP) was fused to the hyper variable region of a small maize GTPase (ROP7) and yellow fluorescent protein (YFP) was fused to the N‐myristoylation motif of the calcium‐dependent protein kinase 1 (LeCPK1) of tomato. Upon co‐expressing in cowpea protoplasts a perfect co‐localization at the plasma membrane of the constructs was observed. Acceptor‐photobleaching FRET microscopy indicated a FRET efficiency of 58% in protoplasts co‐expressing CFP‐Zm7hvr and myrLeCPK1‐YFP, whereas no FRET was apparent in protoplasts co‐expressing CFP‐Zm7hvr and YFP. Fluorescence spectral imaging microscopy (FSPIM) revealed, upon excitation at 435 nm, strong YFP emission in the fluorescence spectra of the protoplasts expressing CFP‐Zm7hvr and myrLeCPK1‐YFP. Also, fluorescence lifetime imaging microscopy (FLIM) analysis indicated FRET because the CFP fluorescence lifetime of CFP‐Zm7hvr was reduced in the presence of myrLeCPK1‐YFP. A FRET fluorescence recovery after photobleaching (FRAP) analysis on a partially acceptor‐bleached protoplast co‐expressing CFP‐Zm7hvr and myrLeCPK1‐YFP revealed slow requenching of the CFP fluorescence in the acceptor‐bleached area upon diffusion of unbleached acceptors into this area. The slow exchange of myrLeCPK1‐YFP in the complex with CFP‐Zm7hvr reflects a relatively high stability of the complex. Together, the FRET data suggest the existence of plasma membrane lipid microdomains in cowpea protoplasts.     

Signal analysis of total internal reflection fluorescent speckle microscopy (TIR-FSM) and wide-field epi-fluorescence FSM of the actin cytoskeleton and focal adhesions in living cells

Fluorescent speckle microscopy (FSM) uses low levels of fluorescent proteins to create fluorescent speckles on cytoskeletal polymers in high‐resolution fluorescence images of living cells. The dynamics of speckles over time encode subunit turnover and motion of the cytoskeletal polymers. We sought to improve on current FSM technology by first expanding it to study the dynamics of a non‐polymeric macromolecular assembly, using focal adhesions as a test case, and second, to exploit for FSM the high contrast afforded by total internal reflection fluorescence microscopy (TIR‐FM). Here, we first demonstrate that low levels of expression of a green fluorescent protein (GFP) conjugate of the focal adhesion protein, vinculin, results in clusters of fluorescent vinculin speckles on the ventral cell surface, which by immunofluorescence labelling of total vinculin correspond to sparse labelling of dense focal adhesion structures. This demonstrates that the FSM principle can be applied to study focal adhesions. We then use both GFP‐vinculin expression and microinjected fluorescently labelled purified actin to compare quantitatively the speckle signal in FSM images of focal adhesions and the actin cytoskeleton in living cells by TIR‐FM and wide‐field epifluorescence microscopy. We use quantitative FSM image analysis software to define two new parameters for analysing FSM signal features that we can extract automatically: speckle modulation and speckle detectability. Our analysis shows that TIR‐FSM affords major improvements in these parameters compared with wide‐field epifluorescence FSM. Finally, we find that use of a crippled eukaryotic expression promoter for driving low‐level GFP‐fusion protein expression is a useful tool for FSM imaging. When used in time‐lapse mode, TIR‐FSM of actin and GFP‐conjugated focal adhesion proteins will allow quantification of molecular dynamics within interesting macromolecular assemblies at the ventral surface of living cells.     

Fluorescence resonance energy transfer of GFP and YFP by spectral imaging and quantitative acceptor photobleaching

To study protein–protein interactions by fluorescence energy transfer (FRET), the proteins of interest are tagged with either a donor or an acceptor fluorophore. For efficient FRET, fluorophores need to have a reasonable overlap of donor emission and acceptor excitation spectra. However, given the relatively small Stokes shift of conventional fluorescent proteins, donor and acceptor pairs with high FRET efficiencies have emission spectra that are difficult to separate. GFP and YFP are widely used in fluorescence microscopy studies. The spectral qualities of GFP and YFP make them one of the most efficient FRET donor–acceptor couples available. However, the emission peaks of GFP (510 nm) and YFP (527 nm) are spectrally too close for separation by conventional fluorescence microscopy. Difficulties in simultaneous detection of GFP and YFP with a fluorescence microscope are eliminated when spectral imaging and subsequent linear unmixing are applied. This allows FRET microscopy using these tags to study protein–protein interactions. We adapted the linear unmixing procedure from commercially available software (Zeiss) for use with acceptor photobleaching FRET using GFP and YFP as FRET pair. FRET efficiencies up to 52% for a GFP-YFP fusion protein were measured. To investigate the applicability of the procedure, we used two constituents of the nucleotide excision repair system, which removes UV-induced single-strand DNA damage. ERCC1 and XPF form a heterodimeric 5' endonuclease in nucleotide excision repair. FRET between ERCC1-GFP and XPF-YFP occurs with an efficiency of 30%.     

Comparative imaging of a bacterial surface-located GFP fusion protein by epifluorescence and scanning near-field optical microscopy

IcsA is an autotransporter protein that plays a role in the virulence of Shigella bacteria. We have examined the cellular localization of a fusion of an IcsA fragment to the green fluorescent protein (GFP) expressed in Escherichia coli using a dual epifluorescence and scanning near-field optical microscope. By combining the data obtained from far-field with near-field microscopy of the same sample, discrimination between surface-bound fusion proteins and fusion proteins located in the cellular cytoplasm becomes possible. Furthermore, and for the first time, the inherent advantages in resolution of the near-field images provides highly specific details of the location of a GFP fusion protein on a bacterial cell surface.     

Spatial control of pa-GFP photoactivation in living cells

Photoactivatable green fluorescent protein (paGFP) exhibits peculiar photo-physical properties making it an invaluable tool for protein/cell tracking in living cells/organisms. paGFP is normally excited in the violet range (405 nm), with an emission peak centred at 520 nm. Absorption cross-section at 488 nm is low in the not-activated form. However, when irradiated with high-energy fluxes at 405 nm, the protein shows a dramatic change in its absorption spectra becoming efficiently excitable at 488 nm. Confocal microscopes allow to control activation in the focal plane. Unfortunately, irradiation extends to the entire illumination volume, making impracticable to limit the process in the 3D (three-dimensional) space. In order to confine the process, we used two advanced intrinsically 3D confined optical methods, namely: total internal reflection fluorescence (TIRF) and two-photon excitation fluorescence (2PE) microscopy. TIRF allows for spatially selected excitation of fluorescent molecules within a thin region at interfaces, i.e. cellular membranes. Optimization of the TIRF optical set-up allowed us to demonstrate photoactivation of paGFP fused to different membrane localizing proteins. Exploitation of the penetration depth showed that activation is efficiently 3D confined even if limited at the interface. 2PE microscopy overcomes both the extended excitation volume of the confocal case and the TIRF constraint of operating at interfaces, providing optical confinement at any focal plane in the specimen within subfemtoliter volumes. The presented results emphasize how photoactivation by non-linear excitation can provide a tool to increase contrast in widefield and confocal cellular imaging.     

Three-dimensionally resolved NAD(P)H cellular metabolic redox imaging of the in situ cornea with two-photon excitation laser scanning microscopy

Three-dimensional maps of cellular metabolic oxidation/reduction states of rabbit cornea in situ were obtained by imaging the fluorescence of the naturally occurring reduced pyridine nucleotides (both reduced nicotinamide-adenine dinucleotide, NADH, and reduced nicotinamide-adenine dinucleotide phosphate, NADPH, denoted here as NAD(P)H). Autofluorescence images with submicrometre lateral resolution were obtained throughout the entire 400 μm thickness of the cornea. Two-photon excitation scanning laser microscopy with near-infrared excitation provided high fluorescence collection efficiency, reduced photodamage, and eliminated ultraviolet chromatic aberration, all of which have previously degraded the visualization of pyridine nucleotide fluorescence. Sharp autofluorescence images of the basal epithelium (40 μm within the cornea) show substantial subcellular detail, providing the ability to monitor autofluorescence intensity changes over time, which reflect changes in oxidative metabolism and cellular dynamics necessary for maintenance of the ocular surface. The autofluorescence was confirmed to be mostly of NAD(P)H origin by cyanide exposure, which increased the fluorescence from all cell types in the cornea by about a factor of two. Autofluorescence images of individual keratocytes in the stroma were observed only after cyanide treatment, while in the predominant extracellular collagen (> 90% of the stromal volume), fluorescence was not distinguished from the background. Observation of keratocyte metabolism demonstrates the sensitivity made available by two-photon microscopy for future redox fluorescence imaging of cellular metabolic states.     

ReAsH: another viable option for in vivo protein labelling in Dictyostelium

Biarsenical-tetracysteine fluorescent protein tagging has been effectively used in a variety of cell types. It has the advantage of requiring a much smaller peptide alteration to existing proteins than fusion to green fluorescent protein (GFP) or monomeric red fluorescent protein (mRFP). However, there are no reports of the tetracysteine tagging system being used in Dictyostelium . In order to establish this tagging system in Dictyostelium , the filamin gene ( FLN ) was modified to express a C-terminal tetracysteine sequence and then transfected into cells. After addition of either FlAsH-EDT₂ or ReAsH-EDT₂, the fluorescence intensity of cells increased in a time-dependent manner and reached a plateau after 3 h of incubation. ReAsH had a much stronger and more specifically localized fluorescent signal compared with FlAsH. After removal of the ReAsH-EDT₂ reagent, the fluorescence signal remained detectable for at least 24 h. The localization of filamin labelled by ReAsH was similar to that of an FLN-mRFP fusion protein, but the fluorescence signal from the ReAsH-labelled protein was stronger. Our findings suggest that the ReAsH-tetracysteine tagging system can be a useful alternative for in vivo protein tagging in Dictyostelium .     

Total internal reflection fluorescent microscopy

This review discusses applications of fluorescence microscopy using totally internally reflected excitation light. When totally internally reflected in a transparent solid at its interface with liquid, the excitation light beam penetrates only a short distance into the liquid. This surface electromagnetic field, called the ‘evanescent wave’, can selectively excite fluorescent molecules in the liquid near the interface. Total internal reflection fluorescence (TIRF) has been used to examine the cell/substrate contact regions of primary cultured rat myotubes with acetylcholine receptors labelled by fluorescent α-bungarotoxin and human skin fibroblasts labelled with a membrane-incorporated fluorescent lipid. TIRF examination of cell/substrate contacts dramatically reduces background from cell autofluorescence and debris. TIRF has also been combined with fluorescence photobleaching recovery and correlation spectroscopy to measure the chemical kinetic binding rates and surface diffusion constant of fluorescent labelled serum protein binding (at equilibrium) to a surface.     

Autofluorescence spectroscopy and imaging of Platymonas subcordiformis irradiated by diode laser based on LSCM

Autofluorescence spectra and optical imaging of Platymonas subcordiformis after irradiation of diode laser were observed via laser scanning confocal microscopy (LSCM). With 488 nm Ar(+) laser excitation, the horizontal and vertical dimensions of a cup-shaped chloroplast of the irradiation group increased about 10% compared with the control group. The fluorescence spectra were similar between irradiation group and control group with a maximum fluorescence band around 682 nm, whereas the former has a higher intensity. Image of a small circular substance with stronger two-photon autofluorescence (TPA) was obtained when using two-photon excitation wavelength of 800 nm in single-channel mode. Further analysis by the 800 nm excitation based on two independent-channels mode showed an emission band of the small circular substance around 376-505 nm, which corresponded to the eyespot of P. subcordiformis. In lambda scanning mode, with two-photon wavelength of 800 nm excitation, six fluorescence peaks that are located at 465, 520, 560, 617, 660 and 680 nm were observed; the fluorescence intensity of the irradiation group was higher than that of the control group, especially at 520, 560 and 617 nm. As a conclusion, diode laser irradiation can promote chloroplast growth of P. subcordiformis cells in the form of expanding area and the increasing content of protein, phospholipids and chlorophyll. LSCM, especially TPA imaging based on femtosecond laser excitation, provides a nondestructive, real-time and accurate method to study changes of living algal cells under laser irradiation and other environmental factors.     

Fluorescence resonance energy transfer and anisotropy reveals both hetero- and homo-energy transfer in the pleckstrin homology-domain and the parathyroid hormone-receptor

We present a method and an apparatus of polarized fluorescence resonance energy transfer (FRET) and anisotropy imaging microscopy done in parallel for improved interpretation of the photophysical interactions. We demonstrate this apparatus to better determine the protein-protein interactions in the pleckstrin homology domain and the conformational changes in the Parathyroid Hormone Receptor, a G-protein coupled receptor, both fused to the cyan and yellow fluorescent proteins for either inter- or intramolecular FRET. In both cases, the expression levels of proteins and also background autofluorescence played a significant role in the depolarization values measured in association with FRET. The system has the sensitivity and low-noise capability of single-fluorophore detection. Using counting procedures from single-molecule methods, control experiments were performed to determine number densities of green fluorescence protein variants CFP and YFP where homo resonance energy transfer can occur. Depolarization values were also determined for flavins, a common molecule of cellular background autofluorescence. From the anisotropy measurements of donor and acceptor, the latter when directly excited or when excited by energy transfer, we find that our instrumentation and method also characterizes crucial effects from homotransfer, polarization specific photobleaching and background molecules.     

The use of fluorescence lifetime imaging (FLIM) for in situ microbial detection in complex mineral substrates

The utility of fluorescence lifetime imaging microscopy (FLIM) for identifying bacteria in complex mineral matrices was investigated. Baseline signals from unlabelled Bacillus subtilis and Euglena gracilis, and Bacillus subtilis labelled with SYTO 9 were obtained using two-photon excitation at 730, 750 and 800 nm, identifying characteristic lifetimes of photosynthetic pigments, unpigmented cellular autofluorescence, and SYTO 9. Labelled and unlabelled B. subtilis were seeded onto marble and gypsum samples containing endolithic photosynthetic cyanobacteria and the ability to distinguish cells from mineral autofluorescence and nonspecific dye staining was examined in parallel with ordinary multichannel confocal imaging. It was found that FLIM enabled discrimination of SYTO 9 labelled cells from background, but that the lifetime of SYTO 9 was shorter in cells on minerals than in pure culture under our conditions. Photosynthetic microorganisms were easily observed using both FLIM and confocal. Unlabelled, nonpigmented bacteria showed weak signals that were difficult to distinguish from background when minerals were present, though cellular autofluorescence consistent with NAD(P)H could be seen in pure cultures, and phasor analysis permitted detection on rocks. Gypsum and marble samples showed similar autofluorescence profiles, with little autofluorescence in the yellow-to-red range. Lifetime or time-gated imaging may prove a useful tool for environmental microbiology. LAY DESCRIPTION : The standard method of bacterial enumeration is to label the cells with a fluorescent dye and count them under high-power fluorescence microscopy. However, this can be difficult when the cells are embedded in soil and rock due to fluorescence from the surrounding minerals and dye binding to ambiguous features of the substrate. The use of fluorescence lifetime imaging (FLIM) can disambiguate these signals and allow for improved detection of bacteria in environmental samples.     

Multiphoton versus confocal high resolution z-sectioning of enhanced green fluorescent microtubules: increased multiphoton photobleaching within the focal plane can be compensated using a Pockels cell and dual widefield detectors

Multiphoton excitation was originally projected to improve live cell fluorescence imaging by minimizing photobleaching effects outside the focal plane, yet reports suggest that photobleaching within the focal plane is actually worse than with one photon excitation. We confirm that when imaging enhanced green fluorescent protein, photobleaching is indeed more acute within the multiphoton excitation volume, so that whilst fluorescence increases as predicted with the square of the excitation power, photobleaching rates increase with a higher order relationship. Crucially however, multiphoton excitation also affords unique opportunities for substantial improvements to fluorescence detection. By using a Pockels cell to minimize exposure of the specimen together with multiple nondescanned detectors we show quantitatively that for any particular bleach rate multiphoton excitation produces significantly more signal than one photon excitation confocal microscopy in high resolution Z‐axis sectioning of thin samples. Both modifications are readily implemented on a commercial multiphoton microscope system.