Fabrication of a novel ZnO–CoO/rGO nanocomposite for nonenzymatic detection of glucose and hydrogen peroxide

Herein, a novel nanocomposite of binary ZnO–CoO nanoparticles loaded on the graphene nanosheets (ZnO–CoO/rGO) has been successfully constructed via a facile, economical and two–step process. The obtained ZnO–CoO/rGO hybrids with high electrical conductivity and abundant active sites, could be modified on a glassy carbon electrode to detect glucose and H₂O₂ multi–functionally. The fabricated biosensor exhibits wide linear range for glucose (10 μM to 11.205 mM) and H₂O₂ (25 μM to 11.1 mM), and their corresponding sensitivity are 168.7 μA mM^?1 cm^?2 and 183.3 μA mM^?1 cm^?2. The limits of detection are 1.3 μM and 0.44 μM for the oxidation of glucose and the reduction of H₂O₂, respectively. Furthermore, remarkable selectivity, long–term stability and outstanding reproducibility of the non–enzyme biosensor prove that ZnO–CoO/rGO hybrids are the promising candidate in practical applications.     

Fabrication of efficient nanostructured Co3O4-Graphene bifunctional catalysts: Oxygen evolution,hydrogen evolution,and H2O2 sensing

Nanostructured Co₃O₄-graphene hybrid catalysts are fabricated by a one-step vacuum kinetic spray technique from microparticles of Co₃O₄ and graphite powders. The Co₃O₄-graphene hybrid catalysts with various Co₃O₄ contents are studied concerning the oxygen evolution reaction (OER), and hydrogen evolution reaction (HER) in 1.0 M KOH, as well as, H₂O₂ sensing in 0.1 M NaOH. We find that increasing graphene content in the hybrid catalysts results in an overall improvement of the OER electrocatalytic activity due to the enhancement in the charge transfer kinetics. The hybrid catalyst with 25 wt% Co₃O₄ reveals the optimum electrocatalytic activity toward the OER with the lowest overpotential (η) of 283 mV@ 10 mA cm⁻² and superior reaction kinetics with a low Tafel slope of 25 mV dec⁻¹. Besides, the OER stability at 50 mA cm⁻² for 50 h in 1.0 M KOH was verified. The hybrid catalyst with 50 wt% Co₃O₄ revealed the highest activity toward the HER with η of 108 mV@ 10 mA cm⁻², Tafel slope of 90 mV.dec⁻¹, and stability at 50 mA cm⁻² for nearly 30 h. Moreover, it reveals ultrahigh H₂O₂ amperometric detection with superior sensitivity of 18,110 μA mM⁻¹ cm⁻², linear detection range from 20 μM to 1 mM, and a limit of detection of 0.14 μM.     

In-situ growth flower-like binder-free 3D CuO/Cu2O-CTAB with tunable interlayer spacing for high performance lithium storage

Copper-based oxides are attractive anode materials for lithium-ion batteries (LIBs) due to their abundant resources, low cost, non-toxic and high capacity. However, copper-based oxides will produce a huge volume change during lithiation/delithiation, and the structural strain caused by periodic volume changes may cause the exfoliation of active materials. Herein, a flower-like binder-free three-dimensional (3D) CuO/Cu₂O-CTAB was prepared by introducing CTAB, which homogeneously grew in situ on a copper mesh framework. The binder-free 3D sample guarantees direct contact between the active material and the copper mesh, maintaining the structure stability. The flower-like CuO/Cu₂O-CTAB with a small size reveals larger active interfaces and provides more active sites. The introduction of CTAB enlarges the interlayer spacing of CuO/Cu₂O, increases the active sites for lithium storage, and adapts to the volume change of the material during lithiation/delithiation. In addition, the expanded interlayer structure helps decrease the ion diffusion energy barrier for accelerating electrochemical reaction kinetics. Therefore, CuO/Cu₂O-CTAB exhibits better lithium storage performance (2.9 mAh cm^?2 at 0.5 mA cm^?2) than bare CuO/Cu₂O (1.8 mAh cm^?2 at 0.5 mA cm^?2).     

Flash sintering of alumina/reduced graphene oxide composites

The flash sintering behavior of Al₂O₃/reduced graphene oxide (rGO) composites was investigated. rGO was used as a composite component and a conductive additive. Under the electric fields of 250–400 V cm⁻¹, the flash event occurred at extremely low temperatures of 236–249 °C. The current density limit played a significant role in the degree of densification. A larger current density resulted in a higher density of the sample. However, current densities larger than 33.33 A cm⁻² resulted in broken samples because of the localization of high current density coupled with the formation of hot spots. Flash sintering at a furnace temperature of 800 °C, electric field of 300 V cm⁻¹ and current density limit of 33.33 A cm⁻² produced nearly completely dense Al₂O₃/rGO composites. In addition to the current limit, the furnace temperature is also a key parameter that controls the degree of densification to achieve “safe” flash sintering.     

Nanoengineering of ZnCo2O4@CoMoO4 heterogeneous structures for supercapacitor and water splitting applications

A hybrid ZnCo₂O₄@CoMoO₄ heterogeneous structure deposited onto nickel foam was synthesized via a two-step hydrothermal process. The results demonstrate that the hybrid architecture exhibits excellent electrochemical performance, including the specific capacitance of 1040C g^?1 at 1 A g^?1 for hybrid structures, high energy density of 87.3 Wh kg^?1 at a power density of 2700 W kg^?1 for an as-assembled supercapacitor and excellent cycle stability with a capacity retention of 99% undergoing 8000 charge-discharge for the device. Moreover, it also shows favorable electrocatalytic activity with low overpotentials of 237 mV at 20 mA cm^?2 for oxygen evolution reaction and 114 mV at 10 mA cm^?2 for hydrogen evolution reaction, and low cell voltage of 1.54 V at 10 mA cm^?2 for overall water splitting. In addition, the stability maintains well for the long-term use of 13 h. We believe that this hybrid ZnCo₂O₄@CoMoO₄ heterogeneous structure could be a promising candidate for future energy storage and conversion.     

Vanadium doped ceramic matrix Li6.7La3Zr1.7V0.3O12 enabled PEO-based solid composite electrolyte with high lithium ion transference number and cycling stability

Solid polymer electrolytes (SPEs) have attracted much attention because of their potential in improving energy density and safety. Vanadium doped ceramic matrix Li_6.7La₃Zr_1.7V_0.3O₁₂ (LLZVO) was synthesized by high-temperature annealing, and formed a composite electrolyte with polyethylene oxide (PEO). Compared with pure PEO electrolyte membrane, the composite electrolyte membrane exhibited better ionic conductivity (30 °C: 3.2 × 10^?5 S cm^?1; 80 °C: 3.6 × 10^?3 S cm^?1). The combination of LLZVO was beneficial to improve the lithium ion transference number (t_Li⁺) of SPE, which was as high as 0.81. The Li/SPE/LiFePO₄ battery shows good cycling ability, with a specific capacity of 142 mAh g^?1 after a stable cycle of 150 cycles. Meanwhile, the symmetrical lithium battery with composite electrolyte can work continuously for 1200 h without short circuit at the current density of 0.1 mA cm^?2 at 50 °C, and the capacity is 0.176 mAh. Vanadium doped ceramic matrix LLZVO as an active ionic conductor, improved the overall performance of solid electrolyte.     

Trifunctional electrocatalysts based on feather-like NiCoP 3D architecture for hydrogen evolution,oxygen evolution,and urea oxidation reactions

Finding efficient and versatile catalysts that can both produce clean energy H₂ and treat wastewater is an important matter to solve energy shortages and wastewater pollution. Herein, a feather-like NiCoP supported on NF was synthesized via the two-step hydrothermal-phosphorization process. NiCoP/NF requires only overpotentials of 44 and 203 mV to reach 10 mA cm^?2 for HER and OER in 1 M KOH, respectively. Besides, NiCoP/NF requires only 1.13 V (vs RHE) to achieve 10 mA cm^?2 in 1 M KOH containing 0.33 M urea. DFT calculation shows that NiCoP exhibits enhanced DOS in the Fermi level attachment, which promotes charge transfer. Subsequently, the trifunctional NiCoP/NF, for overall water splitting, requires a lower potential of 1.48 V to gain 10 mA cm^?2 in 1 M KOH. For urea electrolysis, NiCoP/NF requires just 1.36 V to drive 10 mA cm^?2 in 1 M KOH with 0.33 M urea. This work provides extraordinary insights into electrolytic hydrogen production and wastewater treatment through simple preparative methods. The performance of the prepared catalyst is at a high level in non-noble metal.     

NiFe-NiFe2O4/rGO composites: Controlled preparation and superior lithium storage properties

Binary transition-metal oxides with spinel structure have great potential as advanced anode materials for lithium-ion batteries (LIBs). Herein, NiFe-NiFe₂O₄/ reduced graphene oxide (rGO) composites are obtained via a facile cyanometallic framework precursor strategy to improve the lithium storage performance of NiFe₂O₄. In the composites, NiFe-NiFe₂O₄ nanoparticles with adjustable mass ratios of NiFe₂O₄ to NiFe alloy are homogeneously deposited on rGO sheets. As anode material for LIBs, the optimized NiFe-NiFe₂O₄/rGO composite displays remarkably enhanced lithium storage performance with an initial specific capacity as high as 1362 mAh g⁻¹ at 0.1 A g⁻¹ and a decent capacity retention of ca. 80% after 130 cycles. Besides, the composite delivers a reversible capacity of 550 mAh g⁻¹ at 1 A g⁻¹ after 300 cycles. During the charge–discharge cycles, the aggregation of the NiFe-NiFe₂O₄ nanoparticles and the structural collapse of the electrode can be well alleviated by rGO sheets. Moreover, the conductivity of the electrode can be significantly improved by the well-conductive NiFe alloy and rGO sheets. All these contribute to the improved lithium storage performance of NiFe-NiFe₂O₄/rGO composites.     

Effect of optimal GDC loading on long-term stability of La0.8Sr0.2Co0.2Fe0.8O3-δ/Gd0.2Ce0.8O1.9 composite cathodes

Three types of La_0.8Sr_0.2Co_0.2Fe_0.8O_3-δ/Gd_0.2Ce_0.8O_1.9 (LSCF/GDC) composite cathodes with different optimal GDC loading are fabricated through electrospinning, screen printing and solution infiltration method. Constant current polarization with current density of 100 mA cm^?2 at 750°C is applied to test the stability of LSCF/GDC composite cathodes. After constant current polarization for 144 h, the polarization resistance (R_p) of 280 nm-nanofiber skeletal LSCF/GDC composite cathode after pore-forming exhibits the minimum increase, from 0.062 Ω cm² to 0.098 Ω cm². Scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) results show that the microstructure and surface chemical composition of the cathode maintain stable during the constant current polarization. Combined with the X-ray diffraction (XRD) result, a relationship among GDC loading, stress, Sr surface segregation and long-term stability is established.     

Microwave assisted synthesis of rGO/ZnO composites for non-enzymatic glucose sensing and supercapacitor applications

Zinc oxide (ZnO) and Graphene Oxide (GO) are known to show good electrochemical properties. In this paper, rGO/ZnO nanocomposites have been synthesised using a simple microwave assisted method. The nanocomposites are characterized using XRD, Raman, SEM and TEM. XRD reveals the wurtzite structure of ZnO and TEM shows the heterogeneous nucleation of ZnO nanocrystals anchored onto graphene sheets. The electrochemical properties of the rGO/ZnO nanocomposite enhanced significantly for applications in glucose sensors and supercapacitors. The non-enzymatic glucose sensor of this nanocomposite tested using cyclic voltammetry (CV) and chronoamperometry, exhibits high sensitivity (39.78 mA cm⁻² mM⁻¹) and a lower detection limit of 0.2 nM. The supercapacitor electrode of rGO/ZnO nanocomposite exhibits a significant increase in specific capacitance.     

Flexible rGO-SnO2 supercapacitors converted from pastes containing SnCl2 liquid precursor using atmospheric-pressure plasma jet

Reduced graphene oxide (rGO)-SnO₂ nanocomposites are fabricated on carbon cloth from screen-printed pastes containing rGO nanoflakes and SnCl₂ liquid precursor by using a nitrogen atmospheric-pressure plasma jet (APPJ). RGO-SnO₂-coated carbon cloth is then used as the electrode of gel-electrolyte supercapacitors (SCs). Experiments conducted with various APPJ processing times suggest that the optimal APPJ processing time is 300 s. Cyclic voltammetry (CV) measurements indicate that 300-s APPJ processing results in the best areal capacitance of 97.53 mF/cm². The capacitance retention rate is ~85% after a 10,000-cycle CV test. Further, capacitance increases by 11% after a 1000-cycle bending test under a bending radius of 7.5 mm, possibly owing to the better electrolyte/electrode contact and decrease in the charge transport resistance after mechanical bending. This study also characterized APPJ-processed rGO-SnO₂ nanocomposites by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, X-ray diffractometry, Raman spectroscopy, and water contact angle measurements.     

In-situ synthesis of reduced graphene oxide wrapped Mn3O4 nanocomposite as anode materials for high-performance lithium-ion batteries

We report a novel in-situ symbiosis method to prepare reduced graphene oxide wrapped Mn₃O₄ nanoparticles (rGO/Mn₃O₄) with uniform size about 50 nm as anodes for lithium-ion batteries (LIBs), which can simplify the preparation process and effectively reduce pollution. The rGO/Mn₃O₄ nanocomposite exhibited a reversible specific capacity of 795.5 mAh g^?1 at 100 mA g^?1 after 200 cycles (capacity retention: 87.4%), which benefits from the unique structural advantages and the synergistic effect of rGO and Mn₃O₄. The Mn₃O₄ nanoparticles encapsulated among the rGO nanosheets exhibited good electrochemical activity, and the multilayer wrinkled rGO sheets provided a stable 3D conduction channel for Li⁺/e^? transport. The rGO/Mn₃O₄ nanocomposite is a promising anode candidate for advanced LIBs with excellent cycling performance and rate performance. Furthermore, this new preparation method can be extended to green and economical synthesis of advanced graphene/manganese-based nanocomposites.     

Investigation the sodium storage kinetics of H1.07Ti1.73O4@rGO composites for high rate and long cycle performance

Insertion type material has been attracted plenty of attentions as the anode of sodium ion batteries (SIBs) due to the low volume change induced long cycle stability. H_1.07Ti_1.73O₄ (HTO), a two-dimensional layered material, is a new insertion type anode material for SIBs reported in this study. Layered HTO composites were decorated with rGO nanosheets via an electrostatic assembly method followed by hydrothermal treatment. When adapted as the anode material of SIBs, HTO@rGO composite exhibits an enhanced sodium ion storage behavior, including high rate capability and long cycle stability. It can deliver high capacities of 142.8 and 66.7 mA h g⁻¹ at 100 and 10 000 mA g⁻¹, respectively. Moreover, it can keep a capacity of 75.1 mA h g⁻¹ at 5 A g⁻¹ after even 5000 cycles, corresponding to a high capacity retention of 70.8% (0.0058% capacity decay per cycle). HTO exhibits a small volume expansion of 19.6% by in-situ transmission electron microscopy (in-situ TEM). The diffusion coefficient of sodium ions is increased from 1.77 × 10⁻¹⁴ cm² s⁻¹ in HTO composites to 4.80 × 10⁻¹⁴ cm² s⁻¹ in HTO@rGO composites. Our designed and synthesized HTO@rGO provides a new route for high rate and long cycle stable SIBs anode materials.     

Microwave-assisted synthesis of Co-doped SnO2/rGO for indoor humidity monitoring

The evaluation of indoor humidity is challenging compared to other environmental parameters such as light intensity, temperature, sound and so forth. The proper selection of sensing materials and structural tuning will lead to high-performance humidity sensors. Herein, the SnO₂/rGO and SnO₂/rGO doped with Co nanocomposite were produced by microwave route. The obtained nanocomposite was characterized by XRD, SEM, EDAX, DTA, TGA, FTIR, Raman, and HRTEM. The successful incorporation of Co onto the rGO/SnO₂ is affirmed by the XRD and supported with matching SEM and TEM outcomes where nanoscale particles exist. FTIR reveals the existence of the CC stretching band at ～1570 cm^?1 indicating graphene network sustaining upon reduction. Micro-pores presence is claimed by the adsorption-desorption isotherm curve. The humidity sensing behavior of both structures was evaluated in a wide range of humidity (11–97% RH). The obtained results confirmed that best working frequency for highest humidity change is 50 Hz. Furthermore, upon doping the SnO₂/rGO composite with Co, sensitivity, the response time and recovery time has improved reaching 52 s and 100 s respectively.     

A new As3Mo8V4/PANi/rGO composite for high performance supercapacitor electrode

Herein, [As₂^IIIAs^VMo₈^VIV₄^IVO₄₀]₂[Cu^ICu₂^II(pz)₄]₂·9H₂O/polyaniline/reduced graphene oxide (pz = pyrazine, abbreviated to As₃Mo₈V₄/PANi/rGO) composite is first assembled, characterized and systematically explored for its supercapacitor performance. As₃Mo₈V₄/PANi/rGO composite shows a exceptional specific capacitance (2351 F g^?1 at 1 A g^?1) and outstanding cyclic stability (96.9% after 5000 cycles). The symmetric supercapacitor exhibits high specific capacitance of 1295 F g^?1 at 1 A g^?1 and excellent energy density of 88.1 Wh kg^-1 at power density of 349.6 W kg^-1, while maintaining a notable capacitance retention of 85.7% after 5000 cycles at 2 A g^-1. The above results confirm the potential application of As₃Mo₈V₄/PANi/rGO composite in energy storage devices.     

Al-doping driven electronic structure of α-NiS hollow spheres modified by rGO as high-rate electrode for quasi-solid-state capacitor

Developing an optimized electronic structure of α-NiS electrode material is critical for its high-rate electrochemical performance of quasi-solid-state capacitor. Herein, Al³⁺ have been doped into α-NiS lattice and the reduced graphene oxide (rGO) is employed to modify Al-doping α-NiS, to alleviate the low-mobility charge of α-NiS. The electronic structure and electrochemical properties of α-NiS hollow spheres induced by Al-doping and rGO modification are investigated, both experimental characterization and theoretical results confirm Al-doping affect the electronic structure and electrochemical performance of α-NiS hollow spheres. In the composite of Al-doping α-NiS and rGO (named as Al_xNi_1-xS/rGO), the doped heteroatom improves the intrinsic electronic structure of α-NiS and the rGO provides a good electric conducting network, leading to an enhanced electrochemical performance of α-NiS as high-rate electrode material. After evaluation, the optimized Al_0.2Ni_0.8S/rGO composite shows a superior reversible capacity of 1096 C g^?1 at 2 A g^?1, and retains a capability of 471 C g^?1 at a high-rate of 30 A g^?1. Moreover, an asymmetric quasi-solid-state hybrid capacitors assembled by Al_0.2Ni_0.8S/rGO and activated carbon presents a high energy density of 30.6 Wh kg^?1. This work provides a foundational strategy for the modification of α-NiS through Al-doping and combining with rGO, which has a positive effect on α-NiS electrode material in quasi-solid-state hybrid capacitors.     

Iron oxide supercapacitor of high volumetric energy and power density using binder-free supersonic spraying and self-healing rGO

Iron oxide (Fe₂O₃) nanoparticles and reduced graphene oxide (rGO) sheets were supersonically sprayed onto a nickel substrate to fabricate flexible supercapacitors. The supersonic impact velocity was adjusted by varying the air chamber pressure from 2 to 6 bar, which facilitated the self-healing of Stone-Wall defects in rGO sheets. Supersonic spraying caused exfoliation of the rGO sheets, which in turn increased the surface area and adherence of the Fe₂O₃ nanoparticles. The optimal case exhibited a specific capacitance of 1.44 F?cm^-2 at a current rate of 1.5 mA?cm^-2 and the energy density was 14.23 mWh?cm^-3 at 250 mW?cm^-3. The width of the potential window increased to 1.4 V, implying a significant increase in the energy storage capability. The energy density of the supersonically sprayed Fe₂O₃/rGO electrode also showed no signs of deterioration even when the increased current density interfered with the electrode performance.     

Uniform dispersion of CuO nanoparticles on mesoporous TiO2 networks promotes visible light photocatalysis

Here, we focus our efforts on synthesizing a uniform dispersion of CuO nanoparticles on mesoporous TiO₂ networks for the first time. H₂PtCl₆ was added through a photocatalytic reaction to produce 0.5% Pt/CuO–TiO₂ nanocomposites. XRD patterns confirmed that the prepared TiO₂ formed the anatase phase. TEM images showed close contacts between CuO and TiO₂ with 5–10 nm particle sizes. One of the advantages of the synthesized mesoporous CuO–TiO₂ nanocomposites was the high pore volume (0.540 cm³ g⁻¹) and large surface area (300 m² g⁻¹). The H₂ evolution over the mesoporous 3 wt% CuO–TiO₂ nanocomposites using a glucose hole scavenger [10 vol%] was determined to be ~13000 μmol/g, a value that was 1300 times greater than that of mesoporous TiO₂. The H₂ evolution rate was increased by up to 1300 and 20 times for 3 wt% CuO–TiO₂ and 0.1 wt% CuO–TiO₂ nanocomposites, respectively, compared with that of mesoporous TiO₂. The increase in H₂ evolution over mesoporous CuO–TiO₂ nanocomposites was explained by the increased light harvesting capacity, high glucose molecule diffusion and efficient charge carrier separation. Moreover, the construction of a heterostructure with a p–n CuO–TiO₂ heterojunction expedited the separation of charge carriers and promoted the evolution of H₂. In addition, H₂ evolution was substantially increased by the synergistic effects of Pt and CuO on the mesoporous TiO₂ networks. Photoelectrochemical and photoluminescence measurements were employed to prove the H₂ evolution mechanism over the CuO nanoparticles deposited on the mesoporous TiO₂ networks.     

In-situ generation Cu2O/CuO core-shell heterostructure based on copper oxide nanowires with enhanced visible-light photocatalytic antibacterial activity

As visible light-driven photocatalysts in wastewater treatment, Cu₂O/CuO composites have garnered considerable attention. Herein, Cu₂O/CuO core–shell nanowires were fabricated directly on a Cu mesh using a simple two-step synthesis process involving a wet chemical method and rapid annealing. Unlike conventional composite nanowires, controllable core–shell nanowires exhibit high photoelectrochemical properties and overcome the problems associated with the recovery of powder-based photocatalysts. The presence and structural distribution of the Cu₂O/CuO core–shell nanowires were confirmed using X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. Among the samples subjected to different rapid annealing temperatures for 180 s, the sample exposed to rapid annealing at 350 °C achieved the highest photocurrent density of ?6.96 mA cm^?2. In the core–shell nanowires fabricated on the samples, the ratio of Cu₂O/CuO was 1:1. The photocatalytic activity of the Cu₂O/CuO nanowire samples was also determined by measuring methyl blue degradation to determine their applicability in wastewater treatment. A remarkable photocatalytic degradation rate of 91.6% was achieved at a loading bias voltage of ?0.5 V. The Cu₂O/CuO heterojunction enhanced the photodegradation of the samples because the different bandgaps improved the dissociation of the photogenerated electron–hole pairs. Furthermore, the antibacterial activity of the Cu₂O/CuO nanowires exhibited considerable resistance against Escherichia coli and photocatalytic antibacterial treatment for only 20 min under visible light killed 10⁶ CFU/mL of E. coli. Therefore, the Cu₂O/CuO controllable core–shell nanowires with a high photodegradation performance and excellent antibacterial activity under general illumination show diverse applications in water treatment.     

Synthesis of CuGeO3/reduced graphene oxide nanocomposite by hydrothermal reduction for high performance Li-ion battery anodes

Nowadays, Lithium-ion batteries (LIBs) are prevalently applied in numerous areas, leading to increasing demand of innovative electrodes with high specific capacities. An advanced CuGeO₃/reduced graphene oxide (rGO) structure is designed and fabricated as the anode material taking the advantage of considerable capacity offered by CuGeO₃ and stable framework constructed by rGO. The as-prepared CuGeO₃ with 30 wt% GO addition exhibits the best electrochemical performance. Specifically, a reversible charge capacity of 909 mAh·g⁻¹ with high coulombic efficiency of 91.49% at the current density of 100 mA g⁻¹ after 200 cycles is demonstrated, and the rate capacity retains 747.6 mAh·g⁻¹ with 91.59% capacity retention. These results indicate that the CuGeO₃/rGO composite holds great potential in next-generation LIBs.