Structural and electrochemical characteristics of Li4−xAlxTi5O12 as anode material for lithium-ion batteries

Al-doped Li₄Ti₅O₁₂ in the form of Li_4−xAl_xTi₅O₁₂ (x = 0, 0.05, 0.1 and 0.2) was synthesized via solid state reaction in an Ar-flowing atmosphere. Al-doping does not change the phase composition and particle morphology, but easily results in the lattice distortion and thus the poor crystallinity of Li₄Ti₅O₁₂. Al-doping decreases the specific capacity of Li₄Ti₅O₁₂, while improves remarkably its cycling stability at high charge/discharge rate. The substitution of Al for Li site can enhance the electronic conductivity of Li₄Ti₅O₁₂ via the generation of mixing Ti⁴⁺/Ti³⁺, whereas impede the Li-ion diffusion in the lattice. Excessive Al causes large electrode polarization due to the lower Li-ion conductivity, and thus leads to low specific capacity at high current densities. Li_3.9Al_0.1Ti₅O₁₂ exhibits a relatively high specific capacity and an excellent cycling stability.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Amorphous LiCoO2 thin films on Li1+x+yAlxTi2−xSiyP3−yO12 prepared by radio frequency magnetron sputtering for all-solid-state Li-ion batteries

Amorphous LiCoO₂ thin films were deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 180 °C. The as-deposited LiCoO₂ thin films were characterized by X-ray diffraction, scanning electron microscopy and atomic force microscope. All-solid-state Li/PEO₁₈-Li (CF₃SO₂)₂N/LATSP/LiCoO₂/Au cells were fabricated using the amorphous film. The electrochemical performance of the cells was investigated by galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration technique and electrochemical impedance spectroscopy. It was found that the amorphous LiCoO₂ thin film shows a promising electrochemical performance, making it a potential application in microbatteries for microelectronic devices.     

Effects of B-site ion (M) substitution on the ionic conductivity of (Li3xLa2/3−x)1+y/2(MyTi1−y)O3 (M=Al, Cr)

Effect on the ionic conductivity of B-site ion (M) substitution in (Li_3xLa_2/3−x)_1+y/2M_yTi_1−yO₃ (M=Al, Cr) has been investigated. It has been found that partial substitution of smaller Al³⁺ for Ti⁴⁺ is effective to enhance the ionic conductivity of Li_3xLa_2/3−xTiO₃. At 300 K, the maximum bulk conductivity of (1.58±0.01)×10⁻³ S cm⁻¹ is observed from the composition of (Li_0.39La_0.54)_1−y/2Al_yTi_1−yO₃ with y=0.02 (x=0.13), that is the highest yet reported for known perovskite solutions at room temperature. The conductivity enhancement is interpreted as being due to the substitution-induced bond-strength change rather than due to bottleneck size change for Li migration, TiO₆-octahedron tilting or A-site cation ordering.     

Fabrication and characterization of Li1+x−yNb1−x−3yTix+4yO3 substrates using aqueous tape casting process

An aqueous system for tape casting Li_1+x−yNb_1−x−3yTi_x+4yO₃ (LNT) ceramics was developed using poly(vinyl alcohol) (PVA) binder, ethylene alcohol (EG) plasticizer and ammonium salt of polycarboxylate (PCA-NH₄) dispersant. The zeta potential measurement showed that the isoelectric point of the LNT particles moved slightly toward more acid region after the dispersant absorbed on the particles, while the zeta potential increased significantly. The rheological test indicated that the ceramic slurry exhibited a typical pseudoplastic behavior without thixotropy. The effect of solid loading on the properties of the green tapes was investigated. The increase in the solid loading increased the tensile strength and the green density of the tapes. TGA analysis indicated that the organic additives in the green tapes can be completely removed by heat treatment at 600 °C. SEM micrographs showed that the microstructure of the green and sintered tapes was homogeneous.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Niobium doped lithium titanate as a high rate anode material for Li-ion batteries

Niobium doped lithium titanate with the composition of Li₄Ti_4.95Nb_0.05O₁₂ has been prepared by a sol-gel method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are employed to characterize the structure and morphology of Li₄Ti_4.95Nb_0.05O₁₂. The Li₄Ti_4.95Nb_0.05O₁₂ electrode presents a higher specific capacity and better cycling performance than the Li₄Ti₅O₁₂ electrode prepared by the similar process. The Li₄Ti_4.95Nb_0.05O₁₂ exhibits an excellent rate capability with a reversible capacity of 135 mAh g⁻¹ at 10 C, 127 mAh g⁻¹ at 20 C and even 80 mAh g⁻¹ at 40 C. Electrical resistance measurement and electrochemical impedance spectra (EIS) reveal that the Li₄Ti_4.95Nb_0.05O₁₂ exhibits a higher electronic conductivity and faster lithium-ion diffusivity than the Li₄Ti₅O₁₂, which indicates that niobium doped lithium titanate (Li₄Ti_4.95Nb_0.05O₁₂) is promising as a high rate anode for the lithium-ion batteries.     

High-rate characteristics of novel anode Li4Ti5O12/polyacene materials for Li-ion secondary batteries

In recent years, spinel lithium titanate (Li₄Ti₅O₁₂) as a superior anode material for energy storage battery has attracted a great deal of attention because of the excellent Li-ion insertion and extraction reversibility. However, the high-rate characteristics of this material should be improved if it is used as an active material in large batteries. One effective way to achieve this is to prepare electrode materials coated with carbon. A Li₄Ti₅O₁₂/polyacene (PAS) composite were first prepared via an in situ carbonization of phenol-formaldehyde (PF) resin route to form carbon-based composite. The SEM showed that the Li₄Ti₅O₁₂ particles in the composite were more rounded and smaller than the pristine one. The PAS was uniformly dispersed between the Li₄Ti₅O₁₂ particles, which improved the electrical contact between the corresponding Li₄Ti₅O₁₂ particles, and hence the electronic conductivity of composite material. The electronic conductivity of Li₄Ti₅O₁₂/PAS composite is 10⁻¹ S cm⁻¹, which is much higher than 10⁻⁹ S cm⁻¹ of the pristine Li₄Ti₅O₁₂. High specific capacity, especially better high-rate performance was achieved with this Li₄Ti₅O₁₂/PAS electrode material. The initial specific capacity of the sample is 144 mAh/g at 3 C, and it is still 126.2 mAh/g after 200 cycles. By increasing the current density, the sample still maintains excellent cycle performance.     

Synthesis of sawtooth-like Li4Ti5O12 nanosheets as anode materials for Li-ion batteries

Hierarchical layered hydrous lithium titanate and Li₄Ti₅O₁₂ microspheres assembled by nanosheets have been successfully synthesized via a hydrothermal process and subsequent thermal treatment. The electrochemical properties of the two samples have been investigated by galvanostatic methods. The former, with the obvious layered structure and a large surface area, delivers a reversible capacity of 180 mA h g⁻¹ after 200 cycles at 200 mA g⁻¹. As for Li₄Ti₅O₁₂, with the intriguing and unique sawtooth-like morphology, it presents exceptional high rate performance and excellent cycling stability. Up to 132 mA h g⁻¹ is obtained after 200 cycles at 10,000 mA g⁻¹ (57 C), proving itself promising for high-rate applications.     

Effect of particle dispersion on high rate performance of nano-sized Li4Ti5O12 anode

Nano-sized Li₄Ti₅O₁₂ powders with high dispersivity were fabricated by a sol-gel process using P123 as surfactant, which exhibited much better high rate performance towards Li⁺ insertion/extraction as compared to the densely aggregated Li₄Ti₅O₁₂ particles although the primary grain sizes of both samples were almost the same. The Li₄Ti₅O₁₂ electrode prepared from the well-dispersed nanopowders can preserve 88.6% of the capacity at 0.1 A g⁻¹ when being cycled at 1 A g⁻¹, which is obviously higher than that of the densely aggregated sample, in which only 30% capacity can be retained. By improving the dispersivity, the specific surface area of the Li₄Ti₅O₁₂ nanoparticles, hence the electrode-electrolyte contact area was increased; meanwhile, more homogeneous mixing of the active materials with carbon black was achieved. All these factors might have resulted in the better high rate performance.     

Spray-drying synthesized lithium-excess Li4+xTi5−xO12−δ and its electrochemical property as negative electrode material for Li-ion batteries

Li₄Ti₅O₁₂ (Fd-3m space group) materials were synthesized by controlling the lithium and titanium ratios (Li/Ti) in the range of 0.800-0.900 by using a spray-drying method, followed by calcination at several temperatures between 700 and 900 °C for large-scale production. Chemical and structure studies of the final products were done by X-ray diffraction (XRD), neutron diffraction (ND), X-ray photon electron spectroscopy (XPS), scanning electron microscopy (SEM) and inductively coupled plasma mass spectrometry (ICP-MS). The optimum synthesis condition was examined in relation to the electrochemical characteristics including charge-discharge cycling and ac impedance spectroscopy. It was found that when the spray-drying precursors at the Li/Ti ratio of 0.860 were calcined at 700-900 °C for 12 h in air, a pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase with a lithium-excess composition was obtained. Based on the structural studies, it was found that the excess lithium is located at the lithium and titanium layer of the 16d site in the spinel structure (Fd-3m). These pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase materials showed a higher discharge capacity of ∼164 mAh g⁻¹ at 1.55 V (vs. Li/Li⁺), between the cut-off voltage of 1.2-3.0, with an excellent cyclability and superior rate performance in comparison with the Li₄Ti₅O₁₂ phase containing impurity phases.     

Hydrothermal synthesis of Li4Ti5O12 microsphere with high capacity as anode material for lithium ion batteries

Lithium titanate (Li₄Ti₅O₁₂) microsphere has been successfully synthesized by a hydrothermal method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology of the prepared Li₄Ti₅O₁₂ crystallites. The results show that the as-synthesized powders exhibit outstanding rate capacities and excellent cycling performance. The first discharge capacity at 0.1 C is 172.5 mAh g⁻¹, which is close to the theoretical capacity of 175 mAh/g. After 50 cycles, the efficiency of the synthesized Li₄Ti₅O₁₂ still retains up to 92.8% at 0.1 C and 95.2% at 0.5 C of its initial value, which present a promising applications as anode materials for lithium ion batteries in hybrid and plug-in hybrid electric vehicles.     

Preparation and electrochemical performance of Li4Ti5O12/carbon/carbon nano-tubes for lithium ion battery

A Li₄Ti₅O₁₂/carbon/carbon nano-tubes (Li₄Ti₅O₁₂/C/CNTs) composite was synthesized by using a solid-state method. For comparison, a Li₄Ti₅O₁₂/carbon (Li₄Ti₅O₁₂/C) composite and a pristine Li₄Ti₅O₁₂ were also synthesized in the present study. The microstructure and morphology of the prepared samples are characterized by XRD and SEM. Electrochemical properties of the samples are evaluated by using galvanostatic discharge/charge tests and AC impedance spectroscopy. The results reveal that the Li₄Ti₅O₁₂/C/CNTs composite exhibits the best rate capability and cycling stability among the samples of Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C and Li₄Ti₅O₁₂/C/CNTs. At the charge-discharge rate of 0.5 C, 5.0 C and 10.0 C, its discharge capacities were 163 mAh/g, 148 mAh/g and 143 mAh/g, respectively. After 100 cycles at 5.0 C, it remained at 146 mAh/g.     

Improving the electrochemical performance of Li4Ti5O12/Ag composite by an electroless deposition method

Nano-sized silver particle (<20 nm) was highly dispersed on the surface of Li₄Ti₅O₁₂ particles by an electroless deposition method. The Ag additive played a positive role in improving the electrical contact between Li₄Ti₅O₁₂ particles and the current collector and therefore improved the high rate capacity of Li₄Ti₅O₁₂, but it did not take part in the electrochemical reactions with Li⁺ in Li₄Ti₅O₁₂/Ag composite during the cycling. The experimental results showed that the smaller the silver particles and the more homogeneous dispersion of silver particles in the Li₄Ti₅O₁₂ matrix, the better the cycling performance we obtained.     

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12

A series of spinel Li₄Ti₅O₁₂ samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li₄Ti₅O₁₂. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li₄Ti₅O₁₂ with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li₄Ti₅O₁₂ with L = 1.5 has an initial discharge capacity of 169 mAh g⁻¹ and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good rate performances from 0.2 C to 5 C.     

High-performance Li4Ti5−xVxO12 (0 ≤ x ≤ 0.3) as an anode material for secondary lithium-ion battery

Powders of spinel Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were successfully synthesized by solid-state method. The structure and properties of Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were examined by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electronic microscope (SEM), galvanostatic charge–discharge test and cyclic voltammetry (CV). XRD shows that the V⁵⁺ can partially replace Ti⁴⁺ and Li⁺ in the spinel and the doping V⁵⁺ ion does almost not affect the lattice parameter of Li₄Ti₅O₁₂. Raman spectra indicate that the Raman bands corresponding to the Li–O and Ti–O vibrations have a blue shift due to the doping vanadium ions, respectively. SEM exhibits that Li₄Ti_5−xV_xO₁₂ (0.05 ≤ x ≤ 0.25) samples have a relative uniform morphology with narrow size distribution. Charge–discharge test reveals that Li₄Ti_4.95V_0.05O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 1.0 and 2.0 V; Li₄Ti_4.9V_0.1O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 0.0 and 2.0 V or between 0.5 and 2.0 V. This excellent cycling capability is mainly due to the doping vanadium. CV reveals that electrolyte starts to decompose irreversibly below 1.0 V, and SEI film of Li₄Ti₅O₁₂ was formed at 0.7 V in the first discharge process; the Li₄Ti_4.9V_0.1O₁₂ sample has a good reversibility and its structure is very advantageous for the transportation of lithium-ions.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.