Electrosynthesis of PAni/PPy coatings doped by phosphotungstate on mild steel and their corrosion resistances

Polyaniline/polypyrrole (PAni/PPy), polyaniline-phosphotungstate/polypyrrole (PAni-PW₁₂/PPy) and PAni/PPy-PW₁₂ have been successfully electrodeposited on mild steel (MS) by cyclic voltammetry in aqueous oxalic acid solutions. It was found that the incorporation of PW₁₂ enhanced the corrosion resistance of PAni/PPy coating. Moreover, in comparison to PAni-PW₁₂/PPy, PAni/PPy-PW₁₂ coating exhibited better corrosion resistance for mild steel. After immersion of 36 h in 0.1 M HCl, for instance, the polarization resistance of PAni/PPy-PW₁₂ coating reached 1695 Ω cm², more than those of both PAni/PPy and PAni-PW₁₂/PPy.     

Corrosion behavior of polypyrrole coating doped by dodecylbenzenesulfonate for mild steel in acidic media

This paper describes the electrochemical synthesis of a dodecylbenzenesulfonate doped polypyrrole (PPy-DBS) coating on a passivated mild steel (MS) and investigation of its corrosion protection behaviors. This coating was prepared by cyclic voltammetry technique and characterized by Fourier transform infrared spectroscopy (FT-IR) and field emission scanning electron microscopy (FESEM). The corrosion protection features of the PPy-DBS coated MS were studied in different acid media (0.5?mol L^?1 H₂SO₄ and 0.5?mol L^?1 HCl solutions) using linear potentiodynamic polarization, electrochemical frequency modulation and, electrochemical impedance spectroscopy methods. Electrochemical measurements and FESEM images reveal that the PPy-DBS coating presents effective protection for the MS against corrosive species. This may be ascribed to the barrier effect of the polymer coating and utilization of the dodecylbenzenesulfonate dopant with large size during the electropolymerization process.     

Electrodeposition of polypyrrole–titanate nanotube composites coatings and their corrosion resistance

Polypyrrole (PPy) films (2 μm) containing titanate nanotubes (TiNT) were deposited from 0.5 mol dm⁻³ pyrrole (Py) and 1 g dm⁻³ of TiNT in 0.1 mol dm⁻³ aqueous oxalic acid on 904 L stainless steel (SS) 0.1 mm thickness at 298 K. Electron microscopy showed that the nanotubes were adsorbed on the PPy surface and uniformly dispersed in the polymer matrix. The PPy/TiNT composite contained <10 wt.% titanates which showed an increase of 53% hardness compared with polypyrrole alone. The TiNT provide nucleation centres to catalyze the polymerization of pyrrole and can adsorb up to 240 mg g⁻¹ of the monomer. The corrosion rates for SS, SS/PPy and SS/PPy/TiTN composites, evaluated by linear sweep voltammetry and open-circuit potential measurements in 3% w/v NaCl, were 1.61, 0.008 and 0.004 mg dm⁻² day⁻¹, respectively, indicating that corrosion rates of stainless steel decreased by up to three orders of magnitude in the presence of the composite films.     

Electrochemical synthesis of poly(indole‐co‐thiophene) on low‐nickel stainless steel and its anticorrosive performance in 0.5 mol L−1 H2SO4

The electrochemical synthesis of poly(indole‐co‐thiophene) copolymer coatings was achieved on low‐nickel stainless steel (LN SS) with the cyclic voltammetry technique using indole and thiophene monomers in acetonitrile medium containing lithium perchlorate. The optimization of synthesis parameters such as monomer feed ratio and various scan rates was studied and also their influence on the morphology of the copolymer coatings on LN SS. For the first time, a possible radical cationic electro‐copolymerization mechanism is also proposed in order to understand the electrochemical synthesis. The bonding and structure of the as‐synthesized coatings were characterized using Fourier transform infrared and ¹H NMR spectroscopies. The surface morphology and composition of the coatings were also assessed using scanning electron microscopy and energy‐dispersive X‐ray analysis. It was observed that changes in morphology occurred which had a marked and significant effect on the electrochemical behaviour of the coated LN SS confirmed using electrochemical techniques of potentiodynamic polarization and electrochemical impedance spectroscopy in aqueous 0.5 mol L^?1 H₂SO₄ solution. The obtained results revealed that the copolymer coatings on LN SS provided significant corrosion protection in the acid medium. It was also found that a 1:1 ratio of indole to thiophene yielded the most stable and corrosion‐protective copolymer coating. © 2013 Society of Chemical Industry     

Mica/polypyrrole (doped) composite containing coatings for the corrosion protection of cold rolled steel

Micas/polypyrroles (PPys) doped with molybdate, p-toluene sulfonate, dodecyl benzene sulfonate, and 2-naphthalene sulfonate composite pigments were synthesized by chemical oxidative polymerization and characterized in coatings for corrosion protection on cold rolled steel substrate by various electrochemical techniques. Synthesized composite pigments were characterized for morphology by scanning electron microscopy, which indicated physical formation of PPy on the surface of mica. Chemical composition of the composite pigments was analyzed by X-ray photoelectron spectroscopy which chemically confirmed doped PPy formation on the mica surface. Coatings were formulated at 20% pigment volume concentration (composite pigments or as-received mica pigment) and were applied on cold rolled steel substrate. Coatings were exposed to salt spray test conditions (ASTM B117) for 30 days and were periodically assessed for corrosion with electrochemical impedance spectroscopy (EIS), open circuit potential (OCP), and potentiodynamic polarization. EIS and circuit modeling results demonstrated higher coating resistance (R _c) for mica/PPy (doped) composite coatings as compared to as-received mica pigment containing coating after 30 days of salt spray exposure. Lower current density and more positive corrosion potential values were observed for mica/PPy (doped) composite coatings as compared to mica pigment-based coating in potentiodynamic polarization measurements, indicating improved corrosion protection for cold rolled steel substrate. OCP measurements revealed more positive values for mica/PPy (doped) composite coatings as compared to mica pigment-based coating suggesting superior corrosion protection for mica/PPy (doped) composites.     

Inhibition of corrosion of mild steel by homopolymer and bilayer coatings of polyaniline and polypyrrole

Homopolymers and bilayers of polyaniline (PAni) and polypyrrole (PPy) coatings have been electropolymerized on mild steel by potentiodynamic synthesis technique in aqueous oxalic acid solutions. Characterization of coatings was carried out by cyclic voltammetry. Corrosion behavior of the polymer coated mild steel electrodes was investigated using linear anodic potentiodynamic polarization, Tafel test and electrochemical impedance spectroscopy (EIS) techniques in various aqueous corrosive solutions. Corrosion test results clearly showed that PPy and PAni/PPy bilayer coatings served as a stable host matrix on mild steel against corrosion. However, bilayers of PAni and PPy did not exhibit good combined properties of each polymer, unlike expected. PPy exhibited the best corrosion resistance among all coatings.     

A new method to determine monomer concentration in the polymer particles of emulsion polymerization systems by dynamic light scattering

In the published article cited above, by considering corrections made on the eq. (19) which will be discussed in the next section, Figure 6 should be replaced with a following new Figure 1. Hence, and values of 0.379 and 5.68 mol.dm^?3, respectively, on pages 1055, 1061, and 1062 should be changed to their accurate values of 0.426 and 5.29 mol.dm^?3, respectively.     

High‐performing dye‐sensitized solar cells based on reduced graphene oxide/PEDOT‐PSS counter electrodes with sulfuric acid post‐treatment

Four kinds of counter electrodes are prepared with polystyrene‐sulfonate doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐PSS) as basic material, reduced graphene oxide (rGO) sheets as additives and H₂SO₄ as treating agent. The cyclic voltammetry and Tafel polarization are measured to evaluate catalytic activity of these counter electrodes for /I^? redox couple. It is found that H₂SO₄ treated rGO and PEDOT‐PSS hybrid counter electrode (S/rGO/PEDOT‐PSS counter electrode) has the highest catalytic activity among these counter electrodes. Power conversion efficiency of the dye‐sensitized solar cell with S/rGO/PEDOT‐PSS counter electrode can attain to 7.065%, distinctly higher than that of the cells with the other three ones, owing to the great enhanced fill factor and short‐circuit current density. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42648.     

Effect of Ca2+ induced crosslinking on the mechanical and barrier properties of cast alginate films

The use of alginate as a coating material for packaging applications is currently limited due to its difficult processability and high moisture sensitivity. Therefore, this study addresses the crosslinking and scale‐up to a continuous application. Three different crosslinking agents were applied: CaCl₂ with ethylene diamine tetraacetic acid and two low soluble salts (CaHPO₄ and CaCO₃). Those were incorporated by internal setting in an alginate matrix with varying Ca²⁺ concentration ( ) and ratio. With the addition of Ca²⁺, the tensile strength and elongation at break of the cast alginate films increased. This was optimal for a of 0.010–0.015 g (g alginate)^?1 dependent on the crosslinking agent. The decrease in water vapor and oxygen permeability due to crosslinking was independent of the crosslinking agent. However, the optimal aiming to decrease permeability was different for the crosslinking agents: CaHPO₄ showed best results at a of 0.010 g (g alginate)^?1, CaCl₂ at 0.012 g (g alginate)^?1, and CaCO₃ at 0.027 g (g alginate)^?1. Upon all analyzed properties CaHPO₄ was the most promising crosslinking agent for alginate. Moreover, selected alginate formulations were successfully processed in a continuous lacquering plant. The produced two‐layer systems have very low oxygen permeabilities which can be further reduced by crosslinking. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45754.     

Adsorption of Hg(II) in aqueous solutions using mercapto‐functionalized alkali lignin

A novel adsorbent for Hg(II), mercapto‐functionalized alkali lignin (AL‐SH) was synthesized by Friedel–Crafts alkylation reaction and nucleophilic substitution reactions. The adsorbent was characterized by the techniques of Fourier transform‐infrared spectroscopy (FT‐IR), elementary analysis and thermogravimetric analysis, and N₂ adsorption techniques. The effect of various parameters on Hg(II) adsorption process such as initial pH, contact time, ionic strength, initial Hg(II) concentration, temperature, and adsorbent dosage were investigated in detail through batch static experiments. The results indicated that the adsorption process of Hg(II) on AL‐SH was mainly dependent on the pH and the optimal pH value was at pH ranging from 4.0 to 6.0. The adsorption process was found to follow pseudosecond‐order kinetics and the main process was chemical adsorption, which equilibrated at 8 h. The adsorption isotherm was better described by Langmuir and Temkin isotherm equations compared to Freundlich isotherm equation and the maximum adsorption capacity obtained was 101.2 mg g^?1 (pH = 4.0, 20°C, initial Hg(II) concentration was 200 mg L^?1). The thermodynamic parameters of and were positive while was negative, revealed that the adsorption of Hg(II) onto AL‐SH was a spontaneous and endothermic process with increased entropy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40749.     

Synthesis and characterization of PEDOT derivative with carboxyl group and its chemo sensing application as enhanced optical materials

Poly(4‐(((2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methoxy)methyl)benzoic acid) (PEDOT‐Ph‐COOH) was facilely synthesized by the direct electropolymerization of 4‐(((2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methoxy)methyl)benzoic acid (EDOT‐Ph‐COOH) in CH₂Cl₂‐Bu₄NPF₆ (0.10 M) system, and the PEDOT‐Ph‐COOH films were systematically investigated. The results displayed that the film had excellent reversible redox activities, good electrochemical performance, and rough and compact surface. Finally, the PEDOT‐Ph‐COOH film was used as an optical chemo‐sensor for the highly selective and sensitive detection of F^?, , , , Cu²⁺, and Fe³⁺ in dimethyl sulfoxide. Satisfactory results indicated that optical chemo‐sensor based on PEDOT‐Ph‐COOH possessed an excellent sensing performance and enhanced optical response, and it might be as potential promising materials, such as electrochromic devices, supercapacitors and so on. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41559.     

Reinforcement of polysiloxane/silica elastomer composite by introduction of sacrificial bonds

It is a challenge to improve tear strength of silicone rubber, especially at high filler loading circumstances. A method is offered here to introduce sacrificial bonds into the system. In particular, amide group was introduced onto the phenyl group of monomer methyl phenyl cyclosiloxane ( first, and this functionalized monomer ( was further used for copolymerization with octamethylcyclotetrasiloxane (D₄) and 2,4,6,8‐tetravinyl‐2,4,6,8‐tetramethyl‐cyclotetrasiloxane ( ). Vulcanizates composed by this new copolymer (1A‐50) which amide group‐containing is 1 wt % and with 50 phr TS‐530 exhibit high tear strength of about 54 N ? mm^?1, which is three times higher than that composed by polydimethylsiloxane (PDMS)/TS‐530 (50 phr). The mechanical test indicates this new copolymer a promising candidate for the construction of high tear resistant silicone rubber, especially at high filler loading circumstances. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46129.     

A new smart coating of polyaniline–SiO2 composite for protection of mild steel against corrosion in strong acidic medium

Organic coating approaches for corrosion protection with inherently conducting polymers have become important because of restriction on the use of heavy metals and chromates in coatings due to their environmental problems. The present work is directed towards the synthesis of polyaniline (PANI) and polyaniline–SiO₂ composites (PSCs) by chemical oxidation polymerization in the presence of phosphoric acid and evaluation of synthesized PANI and PSCs for protection of mild steel from corrosion in a strong aggressive medium (i.e. 1.0 mol L^–1 HCl). A suitable coating with PSC was formed on mild steel using epoxy resin by the powder coating technique. A comparative study of the corrosion protection efficiency of mild steel coated with PANI and PSC in 1.0 mol L^–1 HCl solution was evaluated using the Tafel extrapolation, chrono‐amperometry and weight loss methods. The PSC coating showed that a significant reduction in the corrosion current density reflects the better protection of mild steel in an acidic environment. Higher protection efficiency up to 99% was achieved by using PSC‐coated mild steel at 6.0 wt% loading of PSC in epoxy resin. The coating performance and corrosion rate of mild steel were investigated by using immersion of polymer‐coated mild steel in 1.0 mol L^–1 HCl for 60 days and indicated that PSC‐coated mild steel showed better performance from corrosion than PANI in an acidic medium.© 2012 Society of Chemical Industry     

Synthesis and characterization of dendritic polypyrrole silver nanocomposite and its application as a new urea biosensor

Polypyrrole and its silver nanocomposite were electrochemically synthesized from aqueous solutions containing pyrrole, potassium chloride (KCl) (system A); pyrrole, KCl, and an anionic surfactant sodium dodecyl sulphate (NaDS) (system B); and pyrrole, silver nitrate, NaDS (system C). Compact and dendritic patterns were observed depending on experimental conditions. The aggregates were characterized by powder X‐ray diffraction, energy‐dispersive X‐ray spectroscopy, scanning electron microscopy, high resolution transmission electron microscopic (HRTEM), and thermal studies (TG/DTG). HRTEM studies indicate that the particle size of PPy‐Ag nanocomposite is ～30 nm. TG studies revealed that systems B and C, have different thermal behavior. Potassium ion selective electrodes were constructed using systems A, B, and C. The electrode prepared with PPy‐Ag nanocomposite showed nernstian behavior with maximum slope of 57 mV. ion‐selective electrode was also constructed for this system based on nonactin‐impregnated PVC matrix membrane. Urease enzyme was immobilized at the surface of as made ion‐selective electrode to develop urea biosensor showing good detection limit. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45705.     

Gold‐nanoparticle‐decorated thermoplastic polyurethane electrospun fibers prepared through a chitosan linkage for catalytic applications

Thermoplastic polyurethane (TPU)‐electrospun‐fiber‐mat‐supported gold catalysts were prepared by the adsorption of gold nanoparticles (AuNPs) onto a TPU electrospun fiber mat after functionalization with chitosan (CS) by a dip‐coating method. The mechanism for the adsorption of AuNPs was electrostatic interaction between the positive charge of CS (? N ) and the negative charge of the AuNP surface (? COO^?) and coordination between the amine groups of CS and gold. The mat was crosslinked with glutaraldehyde vapor to strengthen the adhesion between the CS coating and TPU fibers after the adsorption of AuNPs. The catalytic activity of the supported gold catalyst was evaluated with the reduction of 4‐nitrophenol by NaBH₄ to demonstrate the excellent catalytic performance and its reusability for at least 10 cycles without a loss in activity. The rate constant increased with both an increase in the amount of supported catalyst and an increase in the ratio of the mat surface area to AuNP within the investigated scope. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133 , 44336.     

Synthesis of a novolac‐based 3‐aminopropylsiloxane resin and its application for the removal of Cu2+, Cr3+, and Ni2+ from electroplating wastewater

Novolac resin was modified with 3‐aminopropyltrimthoxysilane to obtain phenol‐formaldehyde‐aminopropylsiloxane resin (PF‐APS). Fourier transformation infra‐red spectra, thermogravimetric analysis, elemental analysis, and pH‐metric titration were used to characterize PF‐APS. Its chemical formula was suggested to be C₁₄H_12.49N_0.1O₂Si_0.1. The resin shows high experimental metal ions uptake capacity within short time of equilibration. The metal capacity was determined by atomic absorption spectrometry to be 0.787 mEq Cu/g. Maximum separation efficiencies of Cu²⁺, Cr³⁺, and Ni²⁺ from aqueous solutions on PF‐APS were at pH 8.0 and time of stirring 60 min; 94.0%, 90.8%, 83.2%, respectively. No significant interference from the background ions Na⁺, Cl^?, and was observed on the separation process. The heavy metal ions were eluted using 0.01 mol L^?1 EDTA at 65°C releasing >94% of the separated metal ions. The method of separation was applied successfully to remove the heavy metal ions Cu²⁺, Cr³⁺, and Ni²⁺ from electroplating wastewater from Dekirnis, Dakahlia Governorate, Egypt. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40993.     

Electrochemical biosensor for detection of formaldehyde in rain water

BACKGROUD: This study describes the construction of an electrochemical formaldehyde biosensor based on poly(glycidyl methacrylate‐co‐3‐methylthienyl methacrylate)/formaldehyde dehydrogenase/polypyrrole [poly(GMA‐co‐MTM)/FDH/PPy] composite film electrode. Formaldehyde dehydrogenase (FDH) was chemically immobilized via the epoxy groups of the glycidyl methacrylate (GMA) side chain of the polymer. Formaldehyde measurements were conducted in 0.1 mol L^?1, pH 8 phosphate buffer solution (PBS) including 0.1 mol L^?1 KCl, 0.5 mmol L^?1 of NAD⁺ (cofactor of the enzyme) and 1 mmol L^?1 of 1,2‐napthoquinone‐4‐sulfonic acid sodium salt (NQS) as mediator with an applied potential of ? 0.23 V (vs. Ag/AgCl, 3 mol L^?1 NaCl). Analytical parameters of the biosensor were calculated and discussed. The biosensor was tested in rain water samples. RESULTS: Sensitivity was found to be 15 000 per mmol L^?1 (500 nA ppm^?1) in a linear range between 0.1 ppm and 3 ppm (3.3–100 µmol L^?1). A minimum detectable concentration of 4.5 ppb (0.15 µmol L^?1) (S/N = 3) with a relative standard deviation (RSD) of 0.73% (n = 5) was obtained from the biosensor. Response time of the biosensor was very short, reaching 99% of its maximum response in about 4 s. The biosensor was also tested for formaldehyde measurements in rain water samples. Formaldehyde concentrations in samples were calculated using the proposed biosensor with recovery values ranged between 92.2 and 97.7% in comparison with the colorimetric Nash method. CONCLUSION: The poly(GMA‐co‐MTM)/FDH/PPy) electrode showed excellent measurement sensitivity in comparison with other formaldehyde biosensor studies. Strong chemical bonding between the enzyme and the copolymer was created via the epoxy groups of the composite film. The proposed biosensor could be used successfully in rain waters without a pretreatment step. © 2012 Society of Chemical Industry     

Effect of CuBr2 salt treatment on the performance of nanocolloidal PPy:PSS multilayer thin film counter electrodes of dye‐sensitized solar cells

A thin Pt layer on fluorine‐doped tin oxide (FTO) glass is commonly used as the counter electrode (CE) for dye‐sensitized solar cells (DSCs). We have investigated thin layers on FTO glass made from spherical polypyrrole (PPy)–poly(styrene sulfonate) (PSS) nanocolloidal particles with and without treatment of CuBr₂ and used them as CEs. The colloidal polymer composite (PPy:PSS) was spin‐coated at 4000 rpm, and PPy:PSS multilayer (one, three, five) films were employed as the CEs. Aqueous solutions of CuBr₂ (0.5 M and 1 M) were coated onto the multilayer CEs, which increased the efficiency of DSCs. When compared with the untreated PPy:PSS counter electrodes, the CuBr₂‐treated PPy:PSS films showed lower charge‐transfer resistance, higher surface roughness, and improved catalytic performance for the reduction of . The enhanced catalytic performance is attributed to the interaction of the superior electrocatalytic activity of PPy:PSS and CuBr₂ salt. Under standard AM 1.5 sunlight illumination, the counter electrodes based on a single‐layer PPy:PSS composite with 0.5 M and 1 M CuBr₂ salt treatment demonstrated power conversion efficiencies (PCE) of 5.8% and 5.6%, respectively. These values are significantly higher than that of the untreated PPy:PSS CE and are comparable with that of a Pt CE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43772.     

Cross‐linked chitosan beads for phosphate removal from aqueous solution

Chitosan beads were cross‐linked with glutaraldehyde (GA) and epichlorohydrin (EP), respectively, at variable composition. The general features of the adsorptive and textural properties of the bead systems were characterized using p‐nitrophenolate (PNP) at pH 8.5. As well, a systematic adsorption study of phosphate dianion (phosphate ( ) species was carried out in aqueous solution at pH 8.5 and 295 K. The Sips isotherm model yielded adsorption parameters for the chitosan bead systems: (i) monolayer adsorption capacity (Q_m) for PNP ranged from 0.30 to 0.52 mmol g^?1 and (ii) Q_m values for the bead systems with ranged from 22.4–52.1 mg g^?1 for these conditions. GA cross‐linked beads reveal greater Q_m values for PNP while EP cross‐linked beads showed greater Q_m values for , in accordance with the surface chemistry and the materials design described herein. The EP cross‐linked beads show favorable adsorption–desorption properties and represents a promising tunable adsorbent system for the effective removal of phosphate dianion species in aqueous solution. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42949.     

Reactive compatibilization of poly(styrene‐ran‐acrylonitrile)/poly(ethylene) blends through the acid–epoxy reaction

Two families of acid functional styrene/acrylonitrile copolymers (SAN) for application as dispersed phase barrier materials in poly(ethylene) (PE) were studied. One type is SAN made by nitroxide mediated polymerization (NMP), which was subsequently chain extended with a styrene/tert‐butyl acrylate (S/tBA) mixture to provide a block copolymer (number average molecular weight M_n = 36.6 kg mol^?1 and dispersity ? = 1.34, after which the tert‐butyl protecting groups were converted to acid groups (SAN‐b‐S/AA). The other acid functional SAN is made by conventional radical terpolymerization (SAN‐AA). SAN‐AA and SAN‐b‐S/AA were each melt blended with PE grafted with epoxy functional glycidyl methacrylate (PE‐GMA) at 160 °C in a twin screw extruder (70:30 wt % PE‐GMA:SAN co/terpolymer). The non‐reactive PE‐g‐GMA/SAN blend had a volume to surface area diameter = 3.0 μm while the reactive blends (via epoxy/acid coupling) (PE‐GMA/SAN‐b‐SAA and PE‐GMA/SAN‐AA) had = 1.7 μm and 1.1 μm, respectively. After thermal annealing, the non‐reactive blend coarsened dramatically while the reactive blends showed little signs of coarsening, suggesting that the acid/epoxy coupling was effective for morphological stability. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44178.