Thermal and thermomechanical properties of hyperbranched polyurethane‐urea/cenosphere hybrids

Hyperbranched polyurethane (HBPU)‐urea/cenosphere hybrid coatings were synthesized by incorporating various concentrations of cenosphere into HB polyester matrix by ultrasonication technique, and this polyester was further used for the preparation of isocyanate terminated HBPU prepolymers by reacting with excess isophorone diisocyanate (IPDI) in a NCO/OH ratio of 1.6 : 1. The desired hybrid coating is obtained by moisture curing the excess NCO present in the prepolymer through film casting. The structure of the hyperbranched polyester (HBPE) was conformed by ¹H, ¹³C NMR and FTIR spectroscopy and the degree of branching (DB) was calculated using Frechet and Frey equations. These hybrid films were characterized by powder XRD, FTIR, SEM, DMTA, and TGA. The structure property correlation, intermolecular/intramolecular hydrogen bonding, the surface morphology, and viscoelastic properties were studied. These results showed an increase in T_g and thermal stability of the hybrid coatings than the base polymer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Hyperbranched polyurethane (HBPU)-urea and HBPU-imide coatings: Effect of chain extender and NCO/OH ratio on their properties

Effect of chain extender and NCO/OH ratio on the properties of hyperbranched polyurethane (HBPU)-urea and HBPU-imide coatings were examined. The NCO terminated pre-polymers were prepared by reacting the first (G1) and the second (G2) generation hyperbranched polyester polyols (HBP-G1 and HBP-G2) with excess diisocyanate. The excess NCO content of the prepolymer was reacted with different chain extenders viz., 3-aminopropyl triethoxysilane (APTES), pyromellitic dianhydride (PMDA) and N-hydroxyphthalimide (NHTM) to obtain HBPU-urea or HBPU-imide coatings. The structure–property relationships of the different coatings were investigated by FTIR peak deconvolution, and these data suggests the highest extent of hydrogen bonding interaction for PMDA-based coatings, which increases with increasing NCO/OH ratio. Film properties were evaluated by TGA, DMTA, UTM and contact angle measurements; these results were supported by FTIR deconvolution results. As per contact angle measurements, hydrophobicity of coatings increased by increasing NCO/OH ratio. The adhesive strength, abrasion resistance, alkali resistance, and gel content of the coatings were also evaluated.     

Thermal and dynamic mechanical characterization of polyurethane–urea–imide coatings

A series of NCO terminated polyurethane (PU)–imide copolymers were synthesized by a systematic three‐step process and were chain extended with different diol/diamine chain extenders. In the first step, isocyanate terminated PU prepolymers were prepared by reacting soft segments such as polyester (PE) polyols and polyether polyols such as polypropylene glycol (PPG‐1000) with hard segments like 2,4‐tolylene‐diisocyanate (TDI) or isophorone‐diisocyanate (IPDI) with NCO/OH ratio 2:1. In the second step, thermally stable heterocyclic imide ring was incorporated using isocyanate terminated PU prepolymers by reacting with pyromellitic dianhydride (PMDA) in a excess‐NCO:anhydride ratio of 1:0.5. The surplus NCO content after imidization was both moisture cured or partially reacted with chain extender and moisture cured. The films were characterized by thermogravimetric (TG), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) instruments. The adhesion strength of these coatings on mild steel (MS), copper (Cu), and aluminum (Al) is dependent on the nature of the substrate. The TGA analysis show good thermal stability. The DMTA results show the microphase separation between the different hard and soft segments. Finally, a structure to property correlation was drawn based on the structure of the soft, hard, and chain extender and the observed properties are useful for understanding and design of intelligent coatings. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3158–3167, 2006     

Synthesis,thermal properties,and morphology of blocked polyurethane/epoxy full‐interpenetrating polymer network

Blocked polyurethane (PU)/epoxy full‐interpenetrating polymer network (full‐IPN) were synthesized from blocked NCO‐terminated PU prepolymer, with 4,4‐methylene diamine as a chain extender and epoxy prepolymer, with 4,4‐methylene diamine as a curing agent, using simultaneous polymerization (SIN) method. From FTIR spectra analysis it was found that the major reactions in the blocked PU/epoxy IPN system are the self‐polymerization of block PU/chain extender and the self‐polymerization of epoxy/curing agent. Meanwhile, from reaction mechanisms the copolymerization of IPN may have occurred at the same time. The weight loss by thermogravimetric analysis decreased with increasing epoxy and filler content. It was confirmed from scanning electron micrography (SEM) that when the blocked PU content increased, the microstructure of IPN became rougher. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 323–328, 2006     

Chain‐linked lactic acid polymers by benzene diisocyanate

Chain‐linked lactic acid polymers with high molecular weight were synthesized by two‐step polymerization method, including polycondensation and chain extending reactions. The effects of chain extender toluene diisocyanate (TDI) on the chain‐linked lactic acid polymers were studied. The polymers obtained were characterized by gel permeation chromatography, fourier transform infrared spectroscopy, ¹H NMR, and differential scanning calorimeter. Reactions between 1,4‐butanediol and lactic acid oligomers led to hydroxyl‐terminated prepolymer, which provided significant increase of molecular weight in the chain extending reaction. In addition, the glass transition temperature (T_g) and the melting temperature (T_m) were increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1045–1049, 2006     

Studies on chain extension of a novel bio‐based engineering elastomer using 4,4‐diphenyl methane diisocyanate as a chain extender

A novel hydroxyl‐terminated bio‐based engineering elastomer (BEE) was synthesized from four bio‐based monomers by adding excess diol. Then the BEE was chain extended in Haake torque rheometer with 4,4‐diphenyl methane diisocyanate (MDI) as chain extender. The molar ratio of NCO/OH, reaction temperature and reaction time of the chain‐extension reaction were studied, and the optimum condition was determined by the gel permeation chromatography (GPC), soxhlet extraction, and fourier transform infrared spectroscopy (FTIR) results. After chain extension, (i) the number‐average molecular weight of BEE became about 3.5 times of the original BEE, (ii) the thermal stability was improved and the crystallization rate was lower, (iii) and the mechanical properties were significantly improved with nano‐SiO₂ as reinforcing filler. The chain‐extended BEE would have potential wide applications in engineering field. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40756.     

Properties of isocyanate‐reactive waterborne polyurethane adhesives: Effect of cure reaction with various polyol and chain extender content

Three series of isocyanate‐reactive waterborne polyurethane adhesives were prepared with various contents of chain extender (4.25/8.25/12.50 mol %) and polyol (20.75/16.75/12.50 mol %). Each series had a fixed amount of excess (residual) NCO group (0.50–2.00 mol %). FTIR and ¹H‐NMR spectroscopy identified the formation of urea crosslink structure mainly above 80°C of various cure temperatures (20–120°C) with excess diisocyanate. The molecular weight, tensile strength, Young's modulus, and adhesive strength depend on excess NCO content and cure temperature and also varied with polyol and chain extender content. The optimum cure temperature was 100°C for all the samples. The tensile strength, Young's modulus, and adhesive strength increased with increasing cure temperature above 60°C up to the optimum temperature) (100°C) and then almost leveled off. Among all the samples, the maximum values of tensile strength, Young's modulus, and adhesive strength were found with 63.22 wt % polyol, 0.93 wt % chain extender, and 1.50 mol % excess (residual) NCO content at 100°C optimum cure temperature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of novel thermoplastic poly(oligophosphazene‐urethane)s

BACKGROUND: Polyurethanes are some of the most popular polymers used in a variety of products, such as coatings, adhesives, flexible and rigid foams, elastomers, etc. Despite the possibility of tailoring their properties, polyurethanes suffer a serious disadvantage of poor thermal stability. Many attempts have been made in order to improve the thermal stability of polyurethanes. RESULTS: A new hydroxyl‐terminated oligomer containing sulfone groups, 2,2‐bis(4‐hydroxy‐4,4‐sulfonyldiphoneloxy)tetraphenoxyoligocyclotriphosphazene (HSPPZ), was synthesized. HSPPZ was characterized using Fourier transform infrared (FTIR), NMR and gel permeation chromatography analyses. A series of novel thermoplastic poly(oligophosphazene‐urethane)s were then synthesized via the reaction of NCO‐terminated polyurethane prepolymer with HSPPZ containing chain‐extender diols. Their structure and properties were investigated using FTIR spectroscopy, thermogravimetric analysis, differential scanning calorimetry, X‐ray diffraction, water contact angle measurement and tensile measurements. CONCLUSION: Compared to conventional thermoplastic polyurethanes, poly(oligophosphazene‐urethane)s exhibit better thermal stability, low‐temperature resistance and hydrophobicity, but their mechanical properties are slightly poorer. Copyright © 2009 Society of Chemical Industry     

FT-IR and XPS studies of polyurethane-urea-imide coatings

A series of polyurethane (PU)-urea-imide coatings were synthesized by a systematic three-step reaction process. Initially isocyanate terminated PU prepolymers were prepared by reacting soft segments such as polyester polyols (prepared from neopentyl glycol, adipic acid, isophathalic acid and trimethylol propane) or polyether polyols (polypropylene glycol-1000) with hard segments such as 2,4-toluene diisocyanate or isophorone diisocyanate with NCO/OH ratio of 2:1. Heterocyclic imide ring into the PU backbone was incorporated by co-polymerization with pyromellitic dianhydride (PMDA) from the excess NCO groups in the PU prepolymer with an NCO/anhydride ratio of 1:0.5 and the surplus NCO content after imidization was moisture cured. PU-urea-imide coatings were also obtained by partial chain extension of the excess NCO groups in the NCO terminated PU-imide copolymers, and the remaining excess NCO groups were completely reacted with atmospheric moisture. The obtained polymers were analyzed with Fourier transform-infrared (FT-IR) and angle resolved X-ray photoelectron spectroscopy (AR-XPS). The type and change in intermolecular H-bonding interaction in the PU-urea-imide films with structural variables was identified by deconvolution of the FT-IR spectra using Origin 6.0 software through Gaussian curve-fitting method. The FT-IR analyses of the PU-urea-imide coating films show dependence of phase separation on the nature of chain extender. Surface characterization data from AR-XPS suggests the dependence of phase segregation behaviour on the nature of the chain extender, which also supports the FT-IR observations.     

Synthesis,characterization, and application of novel amphiphilic poly(D‐gluconamidoethyl methacrylate)‐b‐polyurethane‐b‐ poly(D‐gluconamidoethyl methacrylate) triblock copolymers

Novel amphiphilic ABA‐type poly(D ‐gluconamidoethyl methacrylate)‐b‐polyurethane‐b‐poly(D ‐gluconamidoethyl methacrylate) (PGAMA‐b‐PU‐b‐PGAMA) tri‐block copolymers were successfully synthesized via the combination of the step‐growth and copper‐catalyzed atom transfer radical polymerization (ATRP). Dihydroxy polyurethane (HO‐PU‐OH) was synthesized by the step‐growth polymerization of hexamethylene diisocyanate with poly(tetramethylene glycol). PGAMA‐b‐PU‐b‐PGAMA block copolymers were synthesized via copper‐catalyzed ATRP of GAMA in N, N‐dimethyl formamide at 20°C in the presence of 2, 2′‐bipyridyl using Br‐PU‐Br as macroinitiator and characterized by ¹H‐NMR spectroscopy and GPC. The resulting block copolymer forms spherical micelles in water as observed in TEM study, and also supported by ¹H NMR spectroscopy and light scattering. Miceller size increases with increase in hydrophilic PGAMA chain length as revealed by DLS study. The critical micellar concentration values of the resulting block copolymers increased with the increase of the chain length of the PGAMA block. Thermal properties of these block copolymers were studied by thermo‐gravimetric analysis, and differential scanning calorimetric study. Spherical Ag‐nanoparticles were successfully synthesized using these block copolymers as stabilizer. The dimension of Ag nanoparticle was tailored by altering the chain length of the hydrophilic block of the copolymer. A mechanism has been proposed for the formation of stable and regulated Ag nanoparticle using various chain length of hydrophilic PGAMA block of the tri‐block copolymer. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chain‐extended polyurethane–acrylate ionomer for UV‐curable waterborne coatings

Conventional and chain‐extended UV‐curable waterborne polyurethane–acrylate (PUA) ionomers were prepared from diisocyanate, polyethylene glycol (PEG), dimethylolpropionic acid, and hydroxyethyl methacrylate, and identified with FTIR spectra and 500‐MHz ¹H‐NMR spectra. The number‐average molecular weight (M_n) and polydispersity of chain‐extended PUA were determined by gel permeation chromatography. For the synthesis of chain‐extended PUA, water was employed as the chain extender. The two kinds of PUA prepolymer could be easily dispersed in water in the form of self‐emulsified latex after the carboxyl group attaching to the backbone of PUA was neutralized with tertiary amine. The effects of M_n of PEG, carboxyl content, and type of diisocyanate on the interfacial tension and rheological behavior of PUA dispersions were investigated. The chain‐extended PUA prepolymer could photopolymerize to a greater extent than the conventional PUA, as indicated by differential photocalorimetry. The photopolymerization kinetics of chain‐extended PUA, based on different substrates, were also investigated. The differential scanning calorimetry analysis for the photo‐cured films from PUA dispersions suggested that lower M_n of PEG tended to favor phase mixing between soft and hard segment phases, and higher M_n of PEG would provoke phase separation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1818–1831, 2002; DOI 10.1002/app.10384     

Synthesis and characterization of poly[(1‐vinyl‐1,2,4‐triazole)‐co‐(monomer with carboxylic acid group(s))] and determination of monomer reactivity ratios: I. Acrylic acid

Copolymers of 1‐vinyl‐1,2,4‐triazole (VTAz) and acrylic acid (AA) having different mole ratios were synthesized using free radical‐initiated solution polymerization in dimethylformamide at 70 °C with α,α′‐azobisisobutyronitrile as initiator in nitrogen atmosphere. The compositions of the synthesized copolymers for a wide range of monomer feeds were determined using Fourier transform infrared (FTIR) spectroscopy through recorded absorption bands for VTAz (1510 cm^?1, C?N (triazole ring) stretching mode) and AA (1710 cm^?1, C?O stretching mode) units. The structures of the copolymers were characterized using FTIR and ¹H NMR spectroscopy. The copolymer compositions were also determined from ¹H NMR analysis following proton signals of carboxyl group at 11.8–12.5 ppm of AA and of triazole ring at 7.5–8.1 ppm of VTAz. Monomer reactivity ratios for the VTAz‐AA pair were estimated using linear methods, i.e. Fineman–Ross (FR) and Kelen–Tüdös (KT). From FTIR evaluation, monomer reactivity ratios were calculated as r₁ = 0.404 and r₂ = 1.496 using the FR method and r₁ = 0.418 and r₂ = 1.559 using the KT method. These values were found to be very close to those obtained from NMR evaluation. The two cases r₁r₂ < 1 and r₁ < r₂ indicated the random distribution of the monomers in the final copolymers and the presence of a greater amount of AA units in the copolymer than in the feed, respectively. The observed relatively high activity of complexed growing radical‐AA^? … VTAz was explained by the effect of complex formation between carbonyl groups and triazole fragments in chain growth reactions. Thermal behaviours of copolymers with various compositions were investigated using thermogravimetric and differential scanning calorimetric analyses. It was observed that thermal stabilities and glass transition temperatures of the copolymers increased resulting from complex formation between acid and triazole units. © 2012 Society of Chemical Industry     

Structure–property correlation study of hyperbranched polyurethane–urea (HBPU) coatings

This paper deals with the structure–property relation of different HBPU coatings based on the variation of parameters like, NCO/OH ratio, generation number and type of diisocyanates used. For this, the NCO terminated HBPU prepolymers were synthesized first by reacting the different generation hyperbranched polyesters (HBPs) with excess diisocyanates. In the next step, these HBPU prepolymer coated films were completely moisture cured to get the desired HBPU coatings. The synthesized polymers were confirmed by ¹H, ¹³C NMR and FT-IR spectroscopy methods whereas structure–property relation was drawn from the FT-IR peak deconvolution technique. The degree of branching (DB) and percent composition of different structural units present in the HBPs were calculated from the ¹H and ¹³C NMR data by using Fretch equation. The melt viscosity study of different HBP samples suggests that most polyester sample showed Newtonian behavior. The coating film properties were studied by DMTA, TGA, UTM, and contact angle measurement instruments. DMTA and TGA data shows that the increase of NCO/OH ratio and generation number had a favorable impact on storage modulus (E′), glass transition temperature (T_g), onset degradation temperature (T_1ON) and char residue values of the coatings. The contact angle and UTM data suggest that the hydrophobicity and tensile strength increases but flexibility decreases with increasing the NCO/OH ratio.     

Cast polyurethane elastomers obtained with N,N′‐ethyleneurea and 1,4‐butanediol as chain extenders

Tensile properties and dynamic mechanical thermal properties for polyurethane elastomers extended with N,N′‐ethyleneurea (EU) and 1,4‐butanediol (1,4‐BD) were investigated. Also gel permeation chromatography and extraction experiments for selected elastomers were performed. EU residues were introduced into polyurethane during prepolymer synthesis at 140°C. Such prepolymers with built‐in EU residues were extended with 1,4‐BD for different [NCO]/[OH] molar ratios. The use of EU chain extender produces in general polymers with inferior mechanical properties compared to the typical 1,4‐BD based polyurethanes, although some of the EU‐based polymers show improved strain‐stress parameters. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 728–733, 2000     

Organically modified montmorillonite hyperbranched polyurethane–urea hybrid composites

The synthesis and characterization of hyperbranched polyurethane/clay (HBPu/o-clay) hybrid coatings prepared from HB aliphatic polyester polyols (HPs) and isophorone diisocyanate (IPDI) is reported. The HPs are prepared by reacting adipic acid (AA) separately with pentaerythritol (PE), trimethylol propane (TMP) and glycerol (Gly) in different mole ratios of 0.6:1.0, 0.8:1.0 and 1.0:1.0, respectively. K⁺-montmorillonite (K10) modified with cetyltrimethyl ammonium bromide (CTAB) is used to increase the compatibility between the clay and polymer matrix. The clay is well-dispersed into the polyester matrix by ultrasonication method. Later on, NCO capped HBPU prepolymer (NCO–HBPu) is synthesized from the clay-dispersed polyester by reacting with IPDI at NCO/OH ratio of 1.6:1.0. In the next step, excess NCO content in the binder is cured with moisture. The properties of different HBPu/o-clay hybrid coatings were studied by FTIR, TGA and DMTA instruments and a structure to property correlation is drawn. The deconvolution technique is used to identify the amount of hydrogen bonding present in the hybrid coatings. The TGA and DMTA result showed an enhancement of the thermal stability, room temperature modulus (E′) and glass transition value (T_g) for the clay modified hybrid coatings, and increases with increasing clay content. TGA results also suggest that the PE-based HBPu/o-clay hybrid coatings have higher thermal stability than TMP or Gly-based systems, which are in close agreement to the FTIR analysis.     

A novel synthesis of reactive nano‐clay polyurethane and its physical and dyeing properties

This study is about polyurea prepolymer, which was synthesized from the extender (N‐(2‐hydroxyethyl) ethylene diamine, HEDA or ethylene diamine, EDA) with 4,4′‐diphenylmethane diisocyanate (MDI), as an intercalative agent to intercalate the organic modified montmorillonite clay. Then, it is further reacted with the polyurethane prepolymer, which is polymerized from the polytetramethylene glycol (PTMG) and MDI, to proceed the intercalative polymerization to form a polyurethane/clay nanocomposite polymer. The experimental parameters contain the use of polyurea intercalative prepolymer extender and also the contents of organo‐clay in the prepolymer etc. We expect to get better mechanical property and also to improve the dyeing properties of nano‐clay polyurethane. The polyurethane/clay polymer is synthesized using two‐step method: synthesizing the polyurethane prepolymer from PTMG and MDI and then extended with the polyurea prepolymer modified with the organo‐clay. Because the extender HEDA contains side chain of hydroxyl groups, the modified PU can further react with the reactive dye. From the experimental results of the fine structure (X‐ray and FT‐IR) and mechanical analysis, it is found that the intercalation is successfully achieved. Thedistance of interlayer spacing is manifestly enlarged. The mechanical properties are significantly improved as the content of organo‐clay is increased. Besides, although thedye up‐take is decreased with the increasing content oforgano‐clay, but the water‐resistant fastness is improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of isocyanic acid,m‐phenylenediiso‐propylidene based poly(urethane‐urea) dispersions containing different amount of 2,2‐Bis(hydroxyl methyl)propionic acid

Isocyanic acid, m‐phenylenediiso‐propylidene (m‐TMXDI)‐based anionic poly(urethane‐urea) dispersions were prepared by the prepolymer mixing process. The equivalent ratio of NCO/OH was kept constant at 1.8, while 2,2‐bis(hydroxyl methyl) propionic acid (DMPA) used was varied from 3 to 10 wt %. The colloidal stability of poly(urethane‐urea) dispersions arose entirely from the presence of ionized carboxylic acid groups. The chemical structure of poly(urethane‐urea) dispersions with various amount of DMPA were identified by FTIR and ¹³C NMR analysis. The test results showed that the hydrophilicity of poly(urethane‐urea) dispersions were increased with increase in DMPA content. The degree of chain extension was much lower than the values predicted theoretically due to the side reaction of a small amount of hydrophilic isocyanate‐terminated prepolymer with water. The average particle size of poly(urethane‐urea) dispersions were decreased with an increase in DMPA content, and this lead to an increase in viscosity. Also, the thermal degradation behavior were measured and was shown that the initial degradation temperature shifted to lower temperature with an increase in DMPA content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5737–5746, 2006     

Novel reactive diluents for UV/moisture dual‐curable coatings

The novel silicone‐modified polyacrylate reactive diluents for UV/moisture dual‐curable coatings were synthesized from N,N‐bis[3‐(trimethoxysilyl)propyl]amine and multifunctional acrylates such as ethoxylated trimethylolpropane triacrylate and polyethyleneglycol diacrylate through Michael addition reaction. Their structures were characterized by NMR and FTIR and their average molecular weights were determined by vapor pressure osmometry. With FTIR, it was found that the obtained diluents could be cured both by UV radiation and moisture mode. The ²⁹Si‐NMR showed that dimer was the main condensation product at the initial stage of moisture curing. The rheological behavior of the diluents investigated by rotary viscometer indicated they were very close to Newtonian fluid, and the viscosity of coatings decreased evenly with increasing concentration of reactive diluents in the coatings. In particular, they were found to be highly efficient in diluency and reactivity for UV polymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1500–1504, 2005     

Synthesis and characterization of biodegradable polyurethanes based on L‐cystine/cysteine and poly(ϵ‐caprolactone)

Tunable biodegradable polyurethanes (PUs) with favorable mechanical properties were synthesized from 1,6‐hexamelthylene diisocyanate (HDI) as the hard segment, poly(?‐caprolactone) (PCL) as the soft segment, and L ‐cystine ester as chain extender. The structure of PUs was confirmed by FTIR and ¹H‐NMR. The results of differential scanning calorimeter, thermogravimetric analysis, dynamic mechanical analysis, and tensile test revealed that the thermal and mechanical properties of PUs were strongly influenced by the molecular weight of soft segment PCL. In the presence of glutathione, the disulfide group cleaved into thiols, realizing the PUs degraded and the molecular weight decreased. For PU [550], it remained only 50% of the original M_w. Evaluation of cell viability demonstrated the nontoxicity of the PUs, which facilitated their potential in biomedical applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013