Performance of pineapple leaf fiber–natural rubber composites: The effect of fiber surface treatments

Composites of natural rubber (NR) and short pineapple leaf fiber (PALF) were prepared on a laboratory two‐roll mill. The influences of untreated fiber content and orientation on the processing and mechanical properties of the composites were investigated. The dependence of extent of orientation on fiber concentration was also established. Sodium hydroxide (NaOH) solutions (1, 3, 5, and 7% w/v) and benzoyl peroxide (BPO) (1, 3, and 5 wt % of fiber) were used to treat the surfaces of PALFs. FTIR and scanning electron microscope (SEM) observations were made of the treatments in terms of chemical composition and surface structure. The tensile strength and elongation at break of the composites were later studied. The fiber–matrix adhesion was also investigated using SEM technique. It was found that all surface modifications enhanced adhesion and tensile properties. The treatments with 5% NaOH and 1% BPO provided the best improvement of composite strength (28 and 57% respectively) when compared with that of untreated fiber. The PALF‐NR composites also exhibited better resistance to aging than its gum vulcanizate, especially when combined with the treated fibers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1974–1984, 2006     

Utilization of flyash as filler for polybutyleneterepthalate‐toughened epoxy resin

Flyash, a waste product generated in large quantities in thermal power plants, has been posing problems of disposal. The purpose of the present work was to make a meaningful utilization of flyash as filler in neat epoxy resin matrix and 2% Polybutyleneterepthalate (PBT)/epoxy blend matrix. For this purpose, the tensile, flexural, compression, impact, chemical resistance, and water absorption properties were studied. Composites were made with varying proportion of flyash in epoxy resin and 2% PBT/epoxy blend matrix. Tensile, flexural, and compression properties were measured on a computerized universal testing machine, according to ASTM procedures. Impact strength was determined using izod impact tester for un‐notched specimens. PBT (2%)/epoxy blend matrix composites showed improved mechanical properties over neat epoxy flyash composites. All the composites were found to have good chemical resistance toward acids, solvents, and alkalies. These composites showed better water resistance over neat epoxy flyash composites. POLYM. ENG. SCI. 46:946–953, 2006. © 2006 Society of Plastics Engineers     

Comparison of the role of milled glass and carbon fibers on mechanical properties of (bisphenol A)‐based epoxy composites

The main target of the current work was to study the mechanical properties of milled E‐glass, S‐glass, and high‐strength (carbon fiber)‐reinforced epoxy composites. At first, tensile behavior of the as‐received fibers was evaluated by conducting different tensile tests. Afterwards, the effects of employing an integral blended coupling agent on the performance of the pure epoxy were investigated by microhardness tests and optical microscopic images. Then, the epoxy composites were prepared simply by mixing and stirring 1, 3, and 5 wt% of the milled fibers with the epoxy resin and its hardener. The effects of mixture degassing and addition of the coupling agent to the mixture were examined based on the mechanical properties of the fabricated composites. Also, scanning electron microscope macro‐ and micrographs of the transverse and longitudinal fracture surfaces were used to study the fracture behavior and identify the active toughening mechanisms. The best results were obtained for the degassed and modified milled (carbon fiber epoxy)‐reinforced composite, which enhanced the tensile strength, elongation, Young's modulus, and toughness up to 12%, 17%, 19%, and 27%, respectively. The current study shows that the composite not only is cost effective but also offers better mechanical properties. J. VINYL ADDIT. TECHNOL., 24:130–138, 2018. © 2016 Society of Plastics Engineers     

Mechanical and anticorrosion properties of furan/epoxy‐based basalt fiber‐reinforced composites

A furan/epoxy blend applicable to composite manufacture was studied and corresponding basalt fiber‐reinforced composites were prepared. The processability, mechanical properties, and reasons for the improved mechanical properties of this blend were investigated by rheology machine, mechanical testing machine, and scanning electron microscopy. With excellent processability, furan/epoxy was suitable for manufacturing composites. Furan/epoxy with the ratio of 5/5 showed the best properties, and the impact strength, flexural strength and flexural modulus were 15.43 kJ/m², 102.81 MPa, and 3209.40 MPa, respectively. The river‐like fracture surface of the furan/epoxy system was well consistent with the mechanical properties. The mechanical and anti‐corrosive properties of basalt fiber‐reinforced furan/epoxy composites were also studied. The mechanical properties of composites changed the same as those of furan/epoxy matrix did. Furan resin effectively improved the anti‐acid but not anti‐alkali property of composites, probably because furan could be cured in acidic condition and basalt fiber was resistant to acid and alkali. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44799.     

The effect of surface treatments on the mechanical properties of basalt‐reinforced epoxy composites

Basalt fiber is an emerging alternative reinforcement to glass or carbon depending upon the application. An important contributing parameter to ultimate performance of any composite is the fiber–‐matrix interface, to which toughness and compressive strength are intimately related. To better understand this matrix fiber interaction in controlling properties, we compared different modification strategies and the impact upon the properties of composites. Strategies focussing upon mechanical interlocking through increased surface roughness and covalent chemical bonding using sol/get methods were explored. Combined methods were also used to explore synergistic behavior as well as the use of aliphatic triethylenetetramine (TETA) to react with any covalently attached epoxy groups. Results from single ply composites showed that when the properties were fiber or fiber/matrix dominated, the sol/gel or epoxy silane method gave the largest improvement in ultimate tensile strength increasing 66% and 27% for uni‐weave 0° and 45° laminas. The combined surface modification methods exhibited increases of 45% and 13% for the same laminas. When properties were matrix dominated, the combined strategies produced the highest improvements in ultimate tensile strength of about 55% compared with 37% for sol/gel modification. For 16‐ply plain weave laminates, epoxy silane surface treatments produced the greatest improvements in compressive and interlaminar shear strengths, increasing 52% and 21%, respectively. This correlated with fiber‐ and fiber/matrix‐dominated results from single ply laminas. The combined treatment using TETA however decreased shear and compressive strength by about 20%, while scanning electron microscopy (SEM) evaluation and dynamic mechanical thermal analysis (DMTA) attributed this to increased resin ductility and plasticization. © 2013 Society of Plastics Engineers     

Effect of layering pattern on the physical,mechanical, and thermal properties of jute/bagasse hybrid fiber‐reinforced epoxy novolac composites

In this study, randomly oriented short jute/bagasse hybrid fiber‐reinforced epoxy novolac composites were prepared by keeping the relative volume ratio of jute and bagasse of 1:3 and the total fiber loading 0.40 volume fractions. The effect of jute fiber hybridization and different layering pattern on the physical, mechanical, and thermal properties of jute/bagasse hybrid fiber‐reinforced epoxy novolac composites was investigated. The hybrid fiber‐reinforced composites exhibited fair water absorption and thickness swelling properties. To investigate the effect of layering pattern on thermomechanical behavior of hybrid composites, the storage modulus and loss factor were determined using dynamic mechanical analyzer from 30 to 200°C at a frequency of 1 Hz. The fracture surface morphology of the tensile samples of the hybrid composites was performed by using scanning electron microscopy. The morphological features of the composites were well corroborated with the mechanical properties. Thermogravimetric analysis indicated an increase in thermal stability of pure bagasse composites with the incorporation of jute fibers. The incorporation of hybrid fibers results better improvement in both thermal and dimensional stable compared with the pure bagasse fiber composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

碳纤维湿法缠绕用环氧树脂基体研究

以TDE-85树脂和AFG-90树脂为主体树脂,混合芳香胺为固化剂,研究了一种适合于碳纤维复合材料湿法缠绕成型的树脂配方。结果表明,该树脂的黏度低(＜550 mPa·s)、适用期长,其浇铸体具有优异的力学性能,其拉伸强度为107 MPa,拉伸模量为4．09 GPa,弯曲强度为161 MPa,弯曲模量为3．88 GPa,断裂伸长率超过6%。用其制备的T-700碳纤维缠绕复合材料界面粘接好,NOL环层间剪切强度达到66．8 MPa,拉伸强度达到2．44 GPa。     

Mechanical properties of carbon fiber/epoxy composites: Effects of number of plies,fiber contents,and angle‐ply layers

Multi‐axial multi‐ply fabric (MMF) composites are becoming increasingly popular as reinforcing materials in high‐performance composites due to their high mechanical properties. This work aimed to study the effects of three variable parameters including fiber contents, numbers of plies, and layer orientations on the mechanical properties of MMF composites. Unidirectional carbon fibers and a two‐part epoxy resin were employed to produce the composite laminates using the manual lay‐up process. It was found that the mechanical properties of composites made with 5‐ply were slightly greater than 3‐ply composites. However, there was no highly significant difference between them. Generally, the angle‐ply of the composites showed the greatest effect on the mechanical properties compared with number of plies and layer orientations. The significant improvements in mechanical properties of the composites were further supported using scanning electron microscopy (SEM). Morphologies of the tensile fracture surfaces of composites revealed that the presence of fiber pulled out results in the creation of voids between the fibers and matrix polymer. This causes the mechanical properties of the composites to be reduced. Finally, the enhancement of mechanical properties of composites clearly confirmed that angle‐ply layer (0°,?35°,0°,+35°,0°) had the most significant reinforcing effect among other parameters evaluated. POLYM. ENG. SCI., 54:2676–2682, 2014. © 2013 Society of Plastics Engineers     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Epoxy‐modified cyanate ester resin and its high‐modulus carbon‐fiber composites

Epoxy E51‐modified bisphenol A dicyanate (BADCy) and its high‐modulus carbon fiber (M40) reinforced composites were prepared in this research. The carbon‐fiber composites were prepared by autoclave molding. Differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy of BADCy‐E51 blend systems showed that polycyclotrimerization of BADCy primarily took place at low temperature. Epoxy group reacted with triazine ring group and produced oxazolidinone at high temperature. The data of mechanical properties, water absorption, and heat deflection temperature (HDT) of cured castings showed that the matrix system containing 95 wt% BADCy and 5 wt% E51 had optimum characteristics. Scanning electron microscopy (SEM) analysis of M40 fiber and the fracture surfaces of M40/BADCy‐E51 composite displayed that the adhesion between M40 fiber and BADCy was good though the surface of M40 was inert. The high retention of mechanical properties of M40/BADCy‐E51 composite after long‐term exposure to environmental conditions indicated that the M40/BADCy composite was suitable for space applications. POLYM. COMPOS., 27:402–409, 2006. © 2006 Society of Plastics Engineers     

Mechanical properties of poly(styrene‐co‐acrylonitrile)‐modified epoxy resin/glass fiber composites

Poly(styrene‐co‐acylonitrile) was used to modify diglycedyl ether of bisphenol‐A type epoxy resin cured with diamino diphenyl sulfone and the modified epoxy resin was used as the matrix for fiber‐reinforced composites (FRPs) to get improved mechanical properties. E‐glass fiber was used as fiber reinforcement. The tensile, flexural, and impact properties of the blends and composites were investigated. The blends exhibited considerable improvement in mechanical properties. The scanning electron micrographs of the fractured surfaces of the blends and tensile fractured surfaces of the composites were also analyzed. The micrographs showed the influence of morphology on the properties of blends. Results showed that the mechanical properties of glass FRPs increased gradually upon fiber loading. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of MWCNTs/poly(acrylonitrile‐ styrene‐butadiene)/epoxy hybrid composites

Poly(acrylonitrile‐styrene‐butadiene) (ABS) was used to modify diglycidyl ether of bisphenol‐A (DGEBA) type epoxy resin, and the modified epoxy resin was used as the matrix for making multiwaled carbon tubes (MWCNTs) reinforced composites and were cured with diamino diphenyl sulfone (DDS) for better mechanical and thermal properties. The samples were characterized by using infrared spectroscopy, pressure volume temperature analyzer (PVT), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), thermo mechanical analyzer (TMA), universal testing machine (UTM), and scanning electron microscopy (SEM). Infrared spectroscopy was employed to follow the curing progress in epoxy blend and hybrid composites by determining the decrease of the band intensity due to the epoxide groups. Thermal and dimensional stability was not much affected by the addition of MWCNTs. The hybrid composite induces a significant increase in both impact strength (45%) and fracture toughness (56%) of the epoxy matrix. Field emission scanning electron micrographs (FESEM) of fractured surfaces were examined to understand the toughening mechanism. FESEM micrographs reveal a synergetic effect of both ABS and MWCNTs on the toughness of brittle epoxy matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

In this work, solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. The effect of chemical treatment on aramid fiber has been studied in a composite system. The surface characteristics of aramid fibers were characterized by Fourier transform infrared spectroscopy (FTIR). The interfacial properties of aramid/epoxy composites were investigated by means of the single fiber pull‐out tests. The mechanical properties of the aramid/epoxy composites were studied by interlaminar shear strength (ILSS). As a result, it was found that RES surface treatment is superior to ECP grafting treatment in promoting the interfacial adhesion between aramid fiber and epoxy matrix, resulting in the improved mechanical properties of the composites. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. This was probably due to the presence of reactive functional groups on the aramid fiber surface, leading to an increment of interfacial binding force between fibers and matrix in a composite system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4165–4170, 2006     

快速固化环氧树脂/碳纤维复合材料的性能

利用差示扫描量热分析仪研究了一种快速固化环氧树脂体系的固化工艺参数,确定了以真空辅助树脂灌注工艺制备快速固化环氧树脂/碳纤维复合材料的成型方法,并与常规固化环氧树脂体系制备的碳纤维复合材料进行对比,采用傅里叶变换红外光谱仪对两种材料的树脂基体进行了分析,考察了两种复合材料的纤维含量、孔隙率及力学性能,最后通过扫描电子显微镜观察了快速固化树脂基体与碳纤维的界面结合性。结果表明,快速固化树脂在99℃下固化6 min后固化度可达96%,能够大幅缩减碳纤维复合材料的成型时间,以其制备的碳纤维复合材料拉伸强度比常规固化环氧树脂复合材料高11.20%,弯曲强度高16.92%,纵横剪切强度高7.44%,快速固化树脂与碳纤维界面结合性良好。     

短切CF增强TPEE热塑性复合材料的注射成型及力学性能研究

以热塑性聚酯弹性体(TPEE)为基体材料,8 mm短切碳纤维(CF)为增强材料,制备CF/TPEE复合材料。材料通过双螺杆挤出系统混合塑化、挤出造粒后,再经过注塑成型制备成标准拉伸试样,通过力学性能测试及微观结构观察,系统研究了碳纤维含量和等离子表面处理对CF/TPEE复合材料拉伸性能的影响。结果表明,当碳纤维含量为20%时,CF/TPEE复合材料的拉伸强度最大,为39.08 MPa;相比于纯TPEE,其拉伸强度提高了217%;经过等离子表面处理后,拉伸强度进一步提高了5%。结合拉伸后断面的SEM图发现,注塑试样表层碳纤维取向度高,而近中区和中心层取向度相对较低,这是注射CF/TPEE复合材料拉伸性能提高效应不明显的主要原因。     

Permeability and mechanical property correlation of bio based epoxy reinforced with unidirectional sisal fiber mat through vacuum infusion molding technique

The present investigation is focused to study the permeability of natural fiber during vacuum infusion (VI) process and the effect of the surface treatments of natural fiber, fiber loading direction, resin flow direction and process parameter on the tensile properties of developed composites (sisal/bio based epoxy). The bio based resin exhibits good flow characteristics in NaOH and isocyanate treated fibers which may be attributed to change in polarity. The surface treatments appear to provide an appreciable enhancement in tensile strength through enhanced bonding between fiber and matrix. The longitudinal tensile strength has been found to be higher than that of the transverse direction and the flow along the fiber provides maximum tensile strength. It has also been demonstrated that VI process provides improved mechanical properties as compared to hand‐layup process. Morphological studies of fractured developed composites were performed by scanning electron microscopy (SEM) to understand the de‐bonding of fiber/matrix adhesion. POLYM. COMPOS., 38:2192–2200, 2017. © 2015 Society of Plastics Engineers     

表面处理对玻纤/碳纤增强橡胶基密封复合材料性能的影响

采用压延成张工艺制备碳纤维和玻璃纤维混杂增强非石棉橡胶基密封复合材料(NAFC),以横向抗拉强度作为表征混杂增强橡胶基密封材料中纤维与橡胶界面粘结性能的指标.通过扫描电镜(SEM)对材料横向拉伸试样断口进行形貌分析,及对材料的耐油、耐酸、耐碱性能进行测试,探讨了不同表面处理工艺对纤维与基体界面粘结效果的影响.研究结果表明,对玻璃纤维采用偶联剂KH-550浸渍后涂覆环氧树脂涂层,对碳纤维在空气氧化后涂覆环氧树脂涂层,可有效增强纤维、基体的界面粘结,所制得的混杂纤维增强复合材料具有较好的机械性能和耐介质性能.     

Effect of fiber loading and orientation on mechanical and erosion wear behaviors of glass–epoxy composites

For a composite material, its mechanical behavior and surface damage by solid particle erosion depend on many factors. One of the most important factors is the fiber content. Similarly, these properties are also greatly affected by the fiber orientation. In this work, a series of experiments were carried out to investigate the influence of fiber loading and fiber orientation on mechanical and erosion behavior of glass fiber‐reinforced epoxy composites. The composites were fabricated with three different fiber loadings (20, 30, and 40 wt%) and at four different fiber orientations (15°, 30°, 45°, and 60°). The conclusions drawn on the basis of the experimental findings are discussed, and composite with 30° fiber orientation shows better microhardness compared with other fiber orientations irrespective of fiber loading. Similar observations are also noticed for other mechanical properties of the composites, such as tensile strength, flexural strength, interlaminar shear strength, impact strength, etc. Finally, the morphology of eroded surfaces is examined using scanning electron microscopy (SEM), and possible erosion mechanisms are identified. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Temperature effect on graphene‐filled interface between glass–carbon hybrid fibers and epoxy resin characterized by fiber‐bundle pull‐out test

The overall mechanical performance of glass–carbon hybrid fibers reinforced epoxy composites depends heavily upon fiber–matrix interfacial properties and the service temperatures. Fiber‐bundle pull‐out tests of glass (GF) and/or carbon fiber (CF) reinforced epoxy composites were carried out at room and elevated temperatures. Graphene nanoplatelets were added in the interfacial region to investigate their influence on the interfacial shear strength (IFSS). Results show that IFSS of specimens with fiber‐bundle number ratio of GF:CF = 1:2 is the largest among the hybrid composites, and a positive hybridization effect is found at elevated temperatures. IFSS of all the specimens decreases with the increasing of test temperatures, while the toughness shows a contrary tendency. As verified by scanning electron microscopy observations, graphene nanoplatelets on fiber surface could enhance the IFSS of pure glass/carbon and hybrid fibers reinforced epoxy composites at higher temperatures significantly. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46263.