Online tool condition monitoring in turning titanium (grade 5) using acoustic emission: modeling

This paper presents an online prediction of tool wear using acoustic emission (AE) in turning titanium (grade 5) with PVD-coated carbide tools. In the present work, the root mean square value of AE at the chip–tool contact was used to detect the progression of flank wear in carbide tools. In particular, the effect of cutting speed, feed, and depth of cut on tool wear has been investigated. The flank surface of the cutting tools used for machining tests was analyzed using energy-dispersive X-ray spectroscopy technique to determine the nature of wear. A mathematical model for the prediction of AE signal was developed using process parameters such as speed, feed, and depth of cut along with the progressive flank wear. A confirmation test was also conducted in order to verify the correctness of the model. Experimental results have shown that the AE signal in turning titanium alloy can be predicted with a reasonable accuracy within the range of process parameters considered in this study.     

Experimental investigation of the three-component forces in finish dry hard turning of hardened tool steel at different hardness levels

In this paper, the effects of cutting speed, depth of cut, feed, workpiece hardness (51, 55, 58, 62, and 65?±?1 HRC), tool flank wear, and nose radius on three-component forces in finish dry hard turning (FDHT) of the hardened tool steel AISI D2 were experimentally investigated by utilizing the PCBN inserts. Experimental results showed that the feed force is the lowest in three-component forces and influence of cutting parameters on it is less than two others in the FDHT of AISI D2. Values of the radial force are higher than those of the cutting force when cutting speed, depth of cut, and feed range from 75 to 301 m/min, and 0.10 to 0.40 and 0.05 to 0.20 mm, respectively, but lower in the range between 0.8- and 1.6-mm nose radius. Values of the cutting force are higher than those of the radial force as the workpiece hardness varies from 51 to 58?±?1 HRC while lower in the range between 62 and 65?±?1 HRC. Besides, there are relations between the changing laws of three-component forces and the softening effect of chip, cohesion effect in the tool–chip junction zone, and intenerating effect of metal in the workpiece surface. The high flank wear formation increases the contact with workpiece surface and hence induces tearing–drawing and welding effect duo to instantaneous high temperature.     

Influence of machining parameters on the machinability of particulate reinforced Al/SiC–MMC

The paper presents the result of an experimental investigation on the machinability of silicon carbide particulate aluminium metal matrix composite during turning using a rhombic uncoated carbide tool. The influence of machining parameters, e.g. cutting speed, feed and depth of cut on the cutting force has been investigated. The influence of the length of machining and cutting time on the tool wear and the influence of various machining parameters, e.g. cutting speed, feed, depth of cut on the surface finish criteria has been analyzed through the various graphical representations. The combined effect of cutting speed and feed on the flank wear has also been investigated. The influence of cutting speed, feed and depth of cut on the tool wears and built-up edge is analyzed graphically. The job surface condition and wear of the cutting tool edge for the different sets of experiments have been examined and compared for searching out the suitable cutting condition for effective machining performance during turning of Al/SiC-MMC. Test results show that no built-up edge is formed during machining of Al/SiC-MMC at high speed and low depth of cut. From the test results and different SEM micrographs, suitable range of cutting speed, feed and depth of cut can be selected for proper machining of Al/SiC-MMC.     

A new approach to investigate tool condition using dummy tool holder and sensor setup

The industrial demand for automated machining systems to enhance process productivity and quality in machining aerospace components requires investigation of tool condition monitoring. The formation of chip and its removal have a remarkable effect on the state of the cutting tool during turning. This work presents a new technique using acoustic emission (AE) to monitor the tool condition by separating the chip formation frequencies from the rest of the signal which comes mostly from tool wear and plastic deformation of the work material. A dummy tool holder and sensor setup have been designed and integrated with the conventional tool holder system to capture the time-domain chip formation signals independently during turning. Several dry turning tests have been conducted at the speed ranging from 120 to 180?m/min, feed rate from 0.20 to 0.50?mm/rev, and depth of cut from 1 to 1.5?mm. The tool insert used was TiN-coated carbide while the work material was high-carbon steel. The signals from the dummy setup clearly differ from the AE signals of the conventional setup. It has been observed that time-domain signal and corresponding frequency response can predict the tool conditions. The rate of tool wear was found to decrease with chip breakage even at higher feed rate. The tool wear and plastic deformation were viewed to decrease with the increased radius of chip curvature and thinner chip thickness even at the highest cutting speed, and these have been verified by measuring tool wear. The chip formation frequency has been found to be within 97.7 to 640?kHz.     

Effect of tool edge wear on the cutting forces and vibrations in high-speed finish machining of Inconel 718: an experimental study and wavelet transform analysis

High-speed machining has been receiving growing attention and wide applications in modern manufacture. Extensive research has been conducted in the past on tool flank wear and crater wear in high-speed machining (such as milling, turning, and drilling). However, little study was performed on the tool edge wear??the wear of a tool cutting edge before it is fully worn away??that can result in early tool failure and deteriorated machined surface quality. The present study aims to fill this important research gap by investigating the effect of tool edge wear on the cutting forces and vibrations in 3D high-speed finish turning of nickel-based superalloy Inconel 718. A carefully designed set of turning experiments were performed with tool inserts that have different tool edge radii ranging from 2 to 62???m. The experimental results reveal that the tool edge profile dynamically changes across each point on the tool cutting edge in 3D high-speed turning. Tool edge wear increases as the tool edge radius increases. As tool edge wear dynamically develops during the cutting process, all the three components of the cutting forces (i.e., the cutting force, the feed force, and the passive force) increase. The cutting vibrations that accompany with dynamic tool edge wear were analyzed using both the traditional fast Fourier transform (FFT) technique and the modern discrete wavelet transform technique. The results show that, compared to the FFT, the discrete wavelet transform is more effective and advantageous in revealing the variation of the cutting vibrations across a wide range of frequency bands. The discrete wavelet transform also reveals that the vibration amplitude increases as the tool edge wear increases. The average energy of wavelet coefficients calculated from the cutting vibration signals can be employed to evaluate tool edge wear in turning with tool inserts that have different tool edge radii.     

Effects of Cutting Parameters on Tool Insert Wear in End Milling of Titanium Alloy Ti6A14V

Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6Al4 V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6Al4 V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as: feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6Al4 V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.     

Investigations of flank wear, cutting force, and surface roughness in the machining of Al-6061�CTiB2 in situ metal matrix composites produced by flux-assisted synthesis

This paper presents the results of an experimental investigation on the machinability of in situ Al-6061?CTiB₂ metal matrix composite (MMC) prepared by flux-assisted synthesis. These composites were characterized by scanning electron microscopy, X-ray diffraction, and micro-hardness analysis. The influence of reinforcement ratio of 0, 3, 6, and 9?wt.% of TiB₂ on machinability was examined. The effect of machinability parameters such as cutting speed, feed rate, and depth of cut on flank wear, cutting force and surface roughness were analyzed during turning operations. From the test results, we observe that higher TiB₂ reinforcement ratio produces higher tool wear, surface roughness and minimizes the cutting forces. When machining the in situ MMC with high speed causes rapid tool wear due to generation of high temperature in the machining interface. The rate of flank wear, cutting force, and surface roughness are high when machining with a higher depth of cut. An increase in feed rate increases the flank wear, cutting force and surface roughness.     

Effects of cutting parameters on tool insert wear in end milling of titanium alloy Ti6Al4V

Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6Al4V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6Al4V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as: feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6Al4V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.     

Pre-evaluation on surface profile in turning process based on cutting parameters

Traditional online or in-process surface profile (quality) evaluation (prediction) needs to integrate cutting parameters and several in-process factors (vibration, machine dynamics, tool wear, etc.) for high accuracy. However, it might result in high measuring cost and complexity, and moreover, the surface profile (quality) evaluation result can only be obtained after machining process. In this paper, an approach for surface profile pre-evaluation (prediction) in turning process using cutting parameters and radial basis function (RBF) neural networks is presented. The aim was to only use three cutting parameters to predict surface profile before machining process for a fast pre-evaluation on surface quality under different cutting parameters. The input parameters of RBF networks are cutting speed, depth of cut, and feed rate. The output parameters are FFT vector of surface profile as prediction (pre-evaluation) result. The RBF networks are trained with adaptive optimal training parameters related to cutting parameters and predict surface profile using the corresponding optimal network topology for each new cutting condition. It was found that a very good performance of surface profile prediction, in terms of agreement with experimental data, can be achieved before machining process with high accuracy, low cost, and high speed. Furthermore, a new group of training and testing data was also used to analyze the influence of tool wear on prediction accuracy.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

Integration of cutting force control and chatter suppression control into automatic cutting feed adjustment system design

Abstract

This study designed an automatic cutting feed adjustment system for computer numerical control (CNC) turning machine tools, which integrate the operational characteristics of cutting force control and chatter suppression control to shorten the machining time and maintain the quality of workpieces. The setting of appropriate machining conditions (such as cutting feed, spindle speed and depth of cut) to consider both machining quality and efficiency often causes difficulties for machine tool operators. Therefore, this study uses cutting force control to design an automatic cutting feed adjustment method for cutting tools, and then, the chatter suppression control design is used to modify the cutting force command to suppress cutting chatter. The experimental results of the CNC turning machine tool show that the use of the cutting force control to adjust the cutting feed can shorten the machining time; however, the cutting chatter results in larger surface waviness on the workpiece surface. When the cutting force command is properly modified by actuating the chatter suppression control, the workpiece shows better surface roughness with prolonged machining time. Therefore, the cutting tests demonstrate that the proposed system is feasible for satisfying the machining requirements of the manufacturing processes of mechanical parts for high speed and high accuracy.     

Optimization of surface roughness,cutting force and tool wear of nitrogen alloyed duplex stainless steel in a dry turning process using Taguchi method

In this work, the dry turning parameters of two different grades of nitrogen alloyed duplex stainless steel are optimized by using Taguchi method. The turning operations were carried out with TiC and TiCN coated carbide cutting tool inserts. The experiments were conducted at three different cutting speeds (80, 100 and 120 m/min) with three different feed rates (0.04, 0.08 and 0.12 mm/rev) and a constant depth of cut (0.5 mm). The cutting parameters are optimized using signal to noise ratio and the analysis of variance. The effects of cutting speed and feed rate on surface roughness, cutting force and tool wear were analyzed. The results revealed that the feed rate is the more significant parameter influencing the surface roughness and cutting force. The cutting speed was identified as the more significant parameter influencing the tool wear. Tool wear was analyzed using scanning electron microscope image. The confirmation tests are carried out at optimum cutting conditions. The results at optimum cutting condition are predicted using estimated signal to noise ratio equation. The predicted results are found to be closer to experimental results within 8% deviations.     

高速车削Inconel 718切削力的试验研究

为了研究高速切削Inconel 718的切削力经验公式和各切削参数对切削力的影响显著程度,应用涂层硬质合金刀具对Inconel 718进行了正交车削试验,得到了硬质合金刀具车削Inconel 718的切削力经验公式。分析结果表明:对切削力影响最大的因素是进给量,切削深度和切削速度对试验结果的影响依次减弱。用涂层硬质合金刀具KC5510精车Inconel 718时,采用小进给量、小切削深度、高切削速度可以得到小的切削力,取得良好的切削效果。     

Micro cutting of tungsten carbides with sem direct observation method

This paper describes the micro cutting of wear resistant tungsten carbides using PCD (Poly-Crystalline Diamond) cutting tools in performance with SEM (Scanning Electron Microscope) direct observation method. Turning experiments were also carried out on this alloy (V50) using a PCD cutting tool. One of the purposes of this study is to describe clearly the cutting mechanism of tungsten carbides and the behavior of WC particles in the deformation zone in orthogonal micro cutting. Other purposes are to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, machined surface and tool wear rates by the outer turning of this alloy carried out using the PCD cutting tool during these various cutting conditions. A summary of the results are as follows : (1) From the SEM direct observation in cutting the tungsten carbide, WC particles are broken and come into contact with the tool edge directly. This causes tool wear in which portions scrape the tool in a strong manner. (2) There are two chip formation types. One is where the shear angle is comparatively small and the crack of the shear plane becomes wide. The other is a type where the shear angle is above 45 degrees and the crack of the shear plane does not widen. These differences are caused by the stress condition which gives rise to the friction at the shear plane. (3) The thrust cutting forces tend to increase more rapidly than the principal forces, as the depth of cut and the cutting speed are increased preferably in the orthogonal micro cutting. (4) The tool wear on the flank face was larger than that on the rake face in the orthogonal micro cutting. (5) Three components of cutting force in the conventional turning experiments were different in balance from ordinary cutting such as the cutting of steel or cast iron. Those expressed a large value of thrust force, principal force, and feed force. (6) From the viewpoint of high efficient cutting found within this research, a proper cutting speed was 15 m/min and a proper feed rate was 0.1 mm/rev. In this case, it was found that the tool life of a PCD tool was limited to a distance of approximately 230 m. (7) When the depth of cut was 0.1 mm, there was no influence of the feed rate on the feed force. The feed force tended to decrease, as the cutting distance was long, because the tool was worn and the tool edge retreated. (8) The main tool wear of a PCD tool in this research was due to the flank wear within the maximum value of V_max being about 260 μ.     

Performance prediction of high-pressure coolant assisted turning of Ti-6Al-4V

The present study focuses on the development of predictive models of average surface roughness, chip-tool interface temperature, chip reduction coefficient, and average tool flank wear in turning of Ti-6Al-4V alloy. The cutting speed, feed rate, cutting conditions (dry and high-pressure coolant), and turning forces (cutting force and feed force) were the input variables in modeling the first three quality parameters, while in modeling tool wear, the machining time was the only variable. Notably, the machining environment influences the machining performance; yet, very few models exist wherein this variable was considered as input. Herein, soft computing-based modeling techniques such as artificial neural network (ANN) and support vector machines (SVM) were explored for roughness, temperature, and chip coefficient. The prediction capability of the formulated models was compared based on the lowest mean absolute percentage error. For surface roughness and cutting temperature, the ANN and, for chip reduction coefficient, the SVM revealed the lowest error, hence recommended. In addition, empirical models were constructed by using the experimental data of tool wear. The adequacy and good fit of tool wear models were justified by a coefficient of determination value greater than 0.99.     

TiAlN涂层刀具对40CrNi钢干切削性能的影响

采用电弧离子镀在YT15硬质合金可转位车刀上沉积TiAlN涂层,用该涂层刀具对40CrNi钢进行干切削试验,并对切削过程中的切削力、切削温度、切屑形态进行了分析研究。结果表明:切削速度对切削温度的影响最大,其次是进给量和背吃刀量;随着切削用量的改变,切向力比轴向力、径向力的变化趋势更明显;长环形螺旋屑排屑顺畅,不易缠绕刀具,散热性好,是粗、精加工较理想的切屑形态;随着切削温度的升高,切屑颜色逐渐变为深蓝色。     

硬质合金刀具车削Cr12Mn5Ni4Mo3Al不锈钢的试验研究

使用硬质合金刀具YW2进行Cr12Mn5Ni4Mo3Al不锈钢的干车削试验。分析了切削速度对车削力及表面粗糙度的影响,并采用扫描电子显微镜(SEM)观察刀具的磨损形貌。研究结果表明:使用硬质合金刀具YW2干车削Cr12Mn5Ni4Mo3Al不锈钢时,在小进给量和小背吃刀量切削的条件下,车削三向力的大小顺序为:径向力轴向力切向力;受积屑瘤的影响,表面粗糙度呈现出随车削速度的变化先减小后增大的变化趋势;硬质合金刀具后刀面磨损较轻微,而沿刀尖周围出现了较严重的粘结现象,前刀面上出现了较严重的划痕现象,低速时,前刀面还出现了贝壳状的剥落现象。     

Parametric tool wear estimation solution of HSC appropriate machining

New strategies are used in manufacturing enterprises due to global competition. High-speed cutting offers a very appropriate opportunity to reduce run times since the high cutting speeds and feed rates involved permit the reduction of production times and minimise rework. There are, however, difficulties in judging tool wear [1]. This paper analyses the formation mechanism of tool wear and presents a complete solution to calculate wear using a ball end cutter for high-speed cutting. Chip geometry generated to calculate tool wear is affected by machining conditions such as turning speed, cutting depth and geometries of tool and work piece which in turn determine the key parameters of chip sections such as length of cut and mean chip thickness. An improved algorithm and a knowledge-based decision model developed to calculate effective tool contact are also discussed to help reduce calculation time and improve calculation efficiency. The calculation results include output form and a 3D wear model showing wear data distributed on the tool contour.     

Al2O3基陶瓷刀具车削300M超高强度钢的刀具寿命研究

采用对角正交回归试验法,求得Al2O3基陶瓷刀具切削300M超高强度钢的刀具寿命经验公式,并分析了切削用量对刀具寿命的影响.通过扫描电子显微镜的观察和能谱分析仪的分析,对Al2O3基陶瓷刀具的损坏形态和磨损机理进行了研究.研究表明:Al2O3基陶瓷刀具车削300M超高强度钢时,粘结磨损和磨粒磨损是主要的磨损机理;合理的切削参数为:切削速度200～300 m/min、切削深度0.1～0.15 mm、进给量0.05～0.1 mm/r.     

HIGH SPEED MILLING OF GRAPHITE ELECTRODE WITH ENDMILL OF SMALL DIAMETER

Graphite becomes the prevailing electrode material in electrical discharging machining (EDM)currently.Orthogonal cutting experiments are carried out to study the characteristics of graph- ite chip formation process.High speed milling experiments are conducted to study tool wear and cutting forces.The results show that depth of cut has great influence on graphite chip formation.The removal process of graphite in high speed milling is the mutual result of cutting and grinding process. Graphite is prone to cause severe abrasion wear to coated carbide endmills due to its high abrasive- ness nature.The major patterns of tool wear are flank wear,rake wear,micro-chipping and breakage. Cutting forces can be reduced by adoption of higher cutting speed,moderate feed per tooth,smaller radial and axial depths of cut,and up cutting.