Ni-B-C对La_(0.94)Mg_(0.06)Ni_(3.49)Co_(0.73)Mn_(0.12)Al_(0.20)储氢合金电化学性能的影响

为提高新型AB_3型储氢合金La_(0.94)Mg_(0.06)Ni_(3.49)Co_(0.73)Mn_(0.12)Al_(0.20)的电化学性能,将球磨法制备的Ni-B-C粉末按不同质量分数添加到合金中。采用X射线粉末衍射仪(XRD)和扫描电子显微镜(SEM)分析合金的相结构和表面形貌。结果表明,添加Ni-B-C粉末后,合金相结构没有变化,仍由LaNi_5相和La_2Ni_7相2个相组成,但合金表面出现了细小颗粒。添加Ni-B-C粉末后,合金电极的最大放电容量和放电容量保持率均提高。当添加质量分数为10%的Ni-B-C粉末后,电极的最大放电容量从346 mAh/g增加到363 mAh/g,50个循环后的放电容量保持率从70%提高到77%,交换电流密度I0与极限电流密度IL分别为106和987 mA/g。动电位极化测试表明,电极的抗腐蚀能力也有所增强。综上,Ni-B-C可以提高AB_3型储氢合金的综合电化学性能。     

复合储氢合金Mg1.8Zr0.2Ni- (1.2-x)Ni -xMgTi3结构和电化学性能研究

为改善Mg₂Ni储氢合金电化学性能,采用机械合金化法(Mechanical Alloying,MA),分别制备出改性合金Mg_1.8 Zr Ni以及MgTi₃,按一定比例和Ni混合球磨,制备出纳米晶或非晶化的Mg_1.8Zr_0.2Ni- (1.2-x)Ni -xMgTi₃复合储氢合金。研究结果表明,经部分取代改性和包覆修饰后的复合储氢合金,其表面和内部形成较多的纳米级褶皱、空隙层状和多相结构缺陷。随着MgTi₃含量增加,Mg_1.8Zr_0.2Ni- (1.2-x)Ni -xMgTi₃复合储氢合金初始放电比容量也逐渐增加,当MgTi₃含量为x=0.5时,合金初始放电比容量为973.3 mAh.g_-1。但MgTi3含量超过x=0.5时,其初始放电比容量又有所下降,研究表明添加MgTi₃却不利于复合储氢合金的循环稳定性和高倍率放电性能。通过对Mg_1.8Zr_0.2Ni- (1.0-x)Ni -xMgTi₃复合储氢合金进行线性极化、阳极极化和交流阻抗测试,进一步研究了系列合金电极的表面电化学反应、电荷转移过程、氢在合金中的扩散情况以及它们的电化学性能。     

热处理对包含正二十面体准晶相Ti1.4V0.6Ni合金电极的电化学性能的影响（英文）

研究了热处理前后Ti1.4V0.6Ni合金的结构和电化学性能。采用X射线粉末衍射(XRD)方法分析合金的结构。电化学特性包括放电容量、循环稳定性和高倍率放电性能等。XRD衍射分析表明,在590°C热处理30min的合金,主要包含正二十面体准晶相、Ti2Ni(FCC)相、V基固溶相(BCC)和C14Laves相(Hex)。电化学测试显示,热处理后在30°C和放电电流密度为30mA/g的条件下,合金电极的最大放电容量可达330.9mA·h/g,并且循环稳定性和高倍率放电性能也得到改善。此外,通过电化学阻抗和合金内部氢的扩散系数研究了合金电极的动力学性能。     

碳纳米管对LaNi5稀土合金电化学性能的影响

采用LaNi5稀土合金作为催化剂，用化学气相沉积法(CVD)制备了碳纳米管。研究了含有5％碳纳米管的LaNi5稀土合金电极样品的电化学性能。测定了碳纳米管电极的电化学储氢性能。实验发现：含有碳纳米管的LaNi5稀土合金的电化学放电容量更高，当放电电流密度为100mA／g时，其电化学储氢量高达385mAh／g。其循环寿命也得到了较大改善。循环100次，放电容量仅下降15％。     

La2O3含量对搅拌摩擦加工制备Ni /Al复合材料组织和性能的影响

采用搅拌摩擦加工方法在Al基体中添加不同La₂O₃含量的混合粉末(Ni+La₂O₃),制备 (Ni+La₂O₃)/Al复合材料。采用SEM、EDS、 EPMA及XRD对复合区微观结构及相组成进行分析,采用室温拉伸试验对 (Ni+La₂O₃)/Al复合材料力学性能进行了测试。结果表明,随着La₂O₃含量的增加,(Ni+La₂O₃)/Al复合材料的组织和性能先变好后变差。当La₂O₃添加量达到5%时,复合材料中Al₃Ni增强颗粒分布均匀、颗粒数量最多,块状的Ni粉团聚减少,其抗拉强度达到最大值215MPa,相比Ni/Al复合材料(抗拉强度176MPa),其抗拉强度提高了22%;当La₂O₃的添加量为7%时,复合材料中Al₃Ni增强颗粒含量减少,块状Ni粉团聚重新出现,抗拉强度下降至201MPa。     

Cu添加对La0.7Ce0.3Fe11.54-xCuxMn0.16Si1.3合金及其氢化物磁性能的影响

La(Fe, Si)₁₃系合金是具有一级相变大磁热效应的磁制冷合金,被认为是极具应用前景的磁热效应材料之一。本文采用高频感应悬浮炉制备了添加不同Cu元素比例的La_0.7Ce_0.3Fe_11.54-xCu_xMn_0.16Si_1.3(x=0, 0.05, 0.1, 0.15)合金。并利用粉末XRD衍射仪,扫描电镜(SEM)对合金的相组成、微观组织结构进行了研究,采用多功能振动样品磁强计VersaLab对合金的磁性能进行了分析。添加Cu元素后,合金的居里温度提高,但氢化后添加Cu的合金居里温度反而偏低。随着Cu元素提高磁热性能下降,但La_0.7Ce_0.3Fe_11.44Cu_0.1Mn_0.16Si_1.3H_1.68合金的最大等温磁熵变仍高达8.5 J/kg.K(0 ~ 2 T),相对制冷能力RCP提高(118 J/kg),磁滞明显降低。     

Cr3+掺杂LiNi0.5Mn1.5O4材料的制备及性能研究

采用高温固相法合成了Cr₃₊掺杂的LiNi_0.5Mn_1.5O₄正极材料,研究了掺杂量对材料物理性能和电化学性能的影响。利用XRD、SEM对材料的结构和形貌进行了表征,结果显示样品具有棱边清晰的尖晶石形貌。讨论了不同Cr₃₊掺杂量对LiCr_xNi_0.5-0.5xMn_1.5-0.5xO₄(x=0,0.05,0.1,0.15,0.2)正极材料性能的影响。充放电测试、循环伏安和交流阻抗测试结果表明：当Cr₃₊的掺杂量为x=0.1时(LiCr_0.1Ni_0.45Mn_1.45O₄)正极材料的性能最好,0.1C、0.5C、1C、2C及5C的首次放电比容量依次为131.54mAh g_-1、126.84mAh g_-1、121.28mAh g_-1、116.49mAh g_-1和96.82mAh g_-1,1C倍率下循环50次,容量保持率仍为96.5%。     

非水体系中钒酸锂/聚吡咯复合正极材料的制备及性能研究

采用乙醇作为介质,FeCl₃为氧化剂,对甲苯磺酸钠为掺杂剂,通过吡咯单体在钒酸锂表面的氧化聚合制备出了钒酸锂/聚吡咯(LiV₃O₈/PPy)复合材料。采用X-射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)对复合材料的结构与形貌进行表征。用恒流充放电测试、循环伏安(CV)和交流阻抗(EIS)等研究了聚吡咯包覆量对材料电化学性能的影响。结果表明：在钒酸锂表面均匀地包覆了一层厚度约10nm的聚吡咯,但并没有改变钒酸锂的晶型结构。当聚吡咯包覆量为6% 时,复合材料的电化学性能最好,在0.1C充放电倍率下,首次放电比容量为274mAh/g,循环100次后样品的放电比容量为239.4mAh/g,容量保持率为87.4%,而未包覆PPy的LiV₃O₈,其首次放电比容量为227.4mAh/g,循环100次后样品的放电比容量为160.1mAh/g,容量保持率仅为70.4%。LiV₃O₈/PPy复合正极材料的电化学性能得到了明显提高。     

石墨烯对La_(0.94)Mg_(0.06)Ni_(3.49)Co_(0.73)Mn_(0.12)Al_(0.20)储氢合金电化学性能的影响

为了提高La_(0.94)Mg_(0.06)Ni_(3.49)Co_(0.73)Mn_(0.12)Al_(0.20)储氢合金的电化学性能,利用石墨烯与储氢合金研磨混合来对其进行表面改性处理。采用X射线粉末衍射仪(XRD)和扫描电子显微镜(SEM)分析合金的相结构和表面形貌。结果表明:添加石墨烯后合金的相结构并没有发生改变,石墨烯包覆在了合金的表面,增大了合金的比表面积,提高了合金的电化学性能。当添加质量分数为5%的石墨烯时,电极的最大放电容量可达到380.6mAh/g,容量保持率S50从69.5%提高到71.1%。添加石墨烯后,交换电流密度、极限电流密度和腐蚀电位均变大、电化学反应阻抗降低,说明电极的动力学性能得到改善。     

(Zr55All0Ni5Cu30)0.97Ce0.03非晶合金在含Cl-介质中的腐蚀电化学行为研究

  用电化学技术方法研究了Zr₅₅Al_l0Ni₅Cu₃₀和(Zr₅₅Al_l0Ni₅Cu₃₀)_0.97Ce_0.03非晶合金在含Cl^-介质中的腐蚀电化学行为及添加稀土Ce的影响.结果表明：随Cl^-浓度增加,两种非晶合金的腐蚀速度加快;添加稀土Ce后提高合金耐蚀性;随极化电位的提高,两种非晶合金在0.05 mol/L Na₂SO₄及含Cl^-介质中均出现钝化特征,维钝电流密度随Cl^-浓度增加而减小;Zr₅₅Al_l0Ni₅Cu₃₀非晶合金的电化学阻抗谱由单容抗弧组成(Zr₅₅Al_l0Ni₅Cu₃₀)_0.97Ce_0.03非晶合金的交流阻抗谱在Cl^-浓度较低时呈单容抗弧特征,而随Cl^-浓度的增加,单容抗弧变为双容抗弧.     

Structure and Electrochemical Properties of Rapidly Quenched Mm0.3Ml0.7Ni3.55Co0.75Mn0.4Al0.3 Hydrogen Storage Alloy

The as-cast Mm_0.3Ml_0.7Ni_3.55Co_0.75Mn_0.4Al_0.3 alloy has been treated using rapid-quenching technique at different quenching speeds to improve the electrochemical hydrogen storage properties of the alloys. The morphologic and microstructural characterizations of alloys were studied using x-ray diffraction and transmission electron microscopy. It is observed that the quenched alloy is composed of two main phases, LaNi₅ and LaNi₃, and one minor phase of La₂Ni₃. The microstructures of the alloys vary with the quenching speeds, as well as contain microcrystalline, nanocrystalline, and amorphous structures. The electrochemical hydrogen storage properties were measured using a battery test system. The results indicate that the discharge capacity of the alloy increases initially and then decreases with the rising quenching speeds. The quenched alloy at a speed of 15 m/s exhibits the maximum discharge capacity (388 mAh/g), which is much higher than that of the AB₅-type rare earth-based hydrogen storage alloy reported in previous studies. However, the stability of the electrochemical cycle of the quenched alloy exhibits inverse trends compared with the discharge capacity. The best electrochemical cyclic stability of the quenched alloy can be obtained at a speed of 25 m/s.     

AB3 型 Mm0.78 Mg0.22 Ni2.48 Mn0.09 Al0.23 Co0.47储氢合金的表面氟化处理

目的提高AB3型储氢合金的电化学性能,扩大其应用范围。方法运用HF和NaF组成的溶液对AB3型合金Mm0.78Mg0.22Ni2.48Mn0.09Al0.23Co0.47(Mm由82.3%La和17.7%Nd(均为原子数分数)组成)进行表面处理,考察改性处理对合金相结构、电化学性能以及动力学性能的影响。结果氟化处理后有MgF2相生成,合金电极的最大放电容量得到提高,50次循环后的容量保持率由83.3%提高到92.8%。此外,合金的动力学性能也得到一定改善。结论氟化处理改变了合金的表面结构,提高了其电化学性能。     

Electrochemical hydrogen storage properties of non-stoichiometric La0.7Mg0.3−xCaxNi2.8Co0.5 (x = 0-0.10) electrode alloys

The microstructure and electrochemical hydrogen storage characteristics of La_0.7Mg_0.3−xCa_xNi_2.8Co_0.5 (x = 0, 0.05 and 0.10) alloys prepared by arc-melting and subsequent powder sintering method are investigated. The electrochemical measurement results show that the cycle stability after 100 charge/discharge cycles first increases from 46.4% (x = 0) to 54.3% (x = 0.05), then decreases to 43.2% (x = 0.10), and the high rate dischargeability increases from 64.5% (x = 0) to 68.5% (x = 0.10) at the discharge current density of 1200 mA/g. The electrochemical impedance spectroscopy analysis indicates that the electrochemical kinetics of the alloy electrodes is improved by increasing Ca. The entire results exhibit that a suitable content of Ca (x = 0.05) can improve the overall electrochemical hydrogen storage characteristics of the alloys.     

RE-Mg-Ni系储氢电极合金“电化学相图”的构建

将相图计算和RE-Mg-Ni(RE=Nd,Ce,Y)系储氢电极合金的最大放电容量测试相结合,然后通过矩阵运算的方式构建了合金"电化学相图",提出了一种储氢电极合金设计的新方法,可快速定位高放电容量区域,为储氢电极合金设计提供指导,缩短研发周期。结果表明,Nd-Mg-Ni体系具有较高的最大放电容量,Y-Mg-Ni体系次之,其中NdMgNi4合金的最大放电容量为271.06 mAh·g~(-1)。     

Electrochemical hydrogen absorbing properties of graphite/AB5 alloy composite electrode

Graphite is an inexpensive carbon material, but its hydrogen absorbing performance has attracted little attention. In this paper, in order to lower the cost of nickel metal-hydride (Ni-MH) battery, graphite is used as a hydrogen absorbing material in its negative electrode. The results of charge-discharge tests show that the graphite electrode has poor electrochemical hydrogen absorbing performance. The capacity of the graphite/AB₅ alloy (90 wt%) composite electrode is close to AB₅ alloy (298 mAh/g), but it has higher charge-discharge polarization and difficulty in activation. When graphite is modified with metal nickel powder by a simple ball milling process, the capacity of the composite electrode reaches to 315 mAh/g and its activation is accelerated. The results of electrochemical impedance spectroscopy (EIS) tests show that hydrogen diffusion in the modified composite electrode is more rapid than in AB₅ alloy, thereby resulting in lower charge-discharge polarization and better discharge performance at large currents.     

Ni对非晶态Co-B合金电化学储氢性能的影响

通过化学还原共沉积法引入元素Ni制备了三元非晶态Co-Ni-B合金,并研究了元素Ni对非晶Co-B合金电化学储氢性能的影响。结果表明,含镍23.8at%非晶态Ni-Co-B合金的可逆放电容量约为250mAh/g,较非晶Co-B合金下降约20mAh/g,但循环稳定性二者相同,即在650mA/g的高电流密度下循环60次容量几乎保持不变。但进一步增加Ni含量,含镍35.8at%的非晶态Ni-Co-B合金的放电容量和循环稳定性都较不掺杂时发生大幅下降。但是,元素Ni的引入能有效抑制高电流密度充电过程中Co-B合金表面大量氢气的析出,减小电极放电电压平台和容量在循环过程中的波动。这可能得益于以下2个原因:(1)非晶Ni-Co-B合金对水分解的电催化活性降低;(2)吸附态氢原子在非晶Ni-Co-B合金基体中的扩散速度高于在Co-B合金中的扩散速度。     

Hydrogen storage characteristics of nanocrystalline and amorphous Mg2Ni-type alloys prepared by melt spinning

In order to improve the hydrogen storage characteristics of the Mg₂Ni-type alloys, Ni in the alloy is partially substituted by element Mn, and melt-spinning technology is used for the preparation of the Mg₂Ni_1−xMn_x (x = 0, 0.1, 0.2, 0.3, 0.4) hydrogen storage alloys. The microstructures of the as-cast and spun alloys are characterized by XRD, SEM and HRTEM. The hydrogen absorption and desorption kinetics of the alloys are measured by an automatically controlled Sieverts apparatus. The electrochemical performances are tested by an automatic galvanostatic system. The results show that the as-spun Mn-free alloy holds typical nanocrystalline structure, whereas the as-spun alloys containing Mn displays a nanocrystalline and amorphous structure. The hydrogen absorption and desorption capacities and kinetics of the alloys increase with rising spinning rate. Additionally, melt spinning markedly improves the electrochemical hydrogen storage capacity and cycle stability of the alloys containing Mn. With an increase in the spinning rate from 0 (As-casts is defined as spinning rate of 0 m/s) to 30 m/s, the discharge capacity of the (x = 0.3) alloy mounts up from 92.3 to 211.1 mAh/g, and its capacity retaining rate at 20th charging and discharging cycle grows from 36.21% to 76.02%.     

Improving the performance of hydrogen storage electrodes based on mechanically alloyed Mg61Ni30Y9

Amorphous Mg₆₁Ni₃₀Y₉ powder was produced by mechanical alloying using a Retsch planetary ball mill under liquid nitrogen cooling. Additional gentle milling with graphite powder resulted in a thin graphite coating of powder particles. Further milling with a high energy SPEX mill transferred the alloy into a fully nanocrystalline state. The morphological and microstructural changes were followed by means of XRD, SEM, TEM and DSC. Hydrogen storage electrodes based on those alloy powders were fabricated and their cathodic and anodic polarization behaviour and their charge–discharge cycling behaviour in 6 M KOH solution were investigated. It was found that the alloy modification from a non-defective amorphous to a highly defective nanocrystalline state is more effective for improving the hydrogen sorption properties of the alloy than the graphite coating, but is detrimental for the alloy passivation. Accordingly, a SPEX-milled powder electrode exhibits with C_max = 570 mAh/g a higher maximum discharge capacity than a coated Retsch-milled powder electrode with C_max = 435 mAh/g, but degrades faster during repeated cycling. Using graphite powder supporting material for electrode preparation on a nickel foam carrier was found to be much more beneficial than nickel powder for achieving maximum discharge performance.