In situ preparation of polyimide/amino‐functionalized carbon nanotube composites and their properties

In order to improve the dispersion of carbon nanotubes (CNTs) in polyimide (PI) matrix and the interfacial interaction between CNTs and PI, 4,4′‐diaminodiphenyl ether (ODA)‐functionalized carbon nanotubes (CNTs‐ODA) were synthesized by oxidation and amidation reactions. The structures and morphologies of CNTs‐ODA were characterized using Fourier transform infrared spectrometer, transmission electron microscopy, and thermal gravimetric analysis. Then a series of polyimide/amino‐functionalized carbon nanotube (PI/CNT‐ODA) nanocomposites were prepared by in situ polymerization. CNTs‐ODA were homogeneously dispersed in PI matrix. The influence of CNT‐ODA content on mechanical properties of PI/CNT‐ODA nanocomposites was investigated. It was found that the mechanical properties of nanocomposites were enhanced with the increase in CNT‐ODA loading. When the content of CNTs‐ODA was 3 wt%, the tensile strength of PI/CNT‐ODA nanocomposites was up to 169.07 MPa (87.11% higher than that of neat PI). The modulus of PI/CNTs‐ODA was increased by 62.64%, while elongation at break was increased by 66.05%. The improvement of the mechanical properties of PI/CNT‐ODA nanocomposites were due to the strong chemical bond and interfacial interaction between CNTs‐ODA and PI matrix. POLYM. COMPOS., 35:1952–1959, 2014. © 2014 Society of Plastics Engineers     

A facile route to develop electrical conductivity with minimum possible multi‐wall carbon nanotube (MWCNT) loading in poly(methyl methacrylate)/MWCNT nanocomposites

Today, we stand at the threshold of exploring carbon nanotube (CNT) based conducting polymer nanocomposites as a new paradigm for the next generation multifunctional materials. However, irrespective of the reported methods of composite preparation, the use of CNTs in most polymer matrices to date has been limited by challenges in processing and insufficient dispersability of CNTs without chemical functionalization. Thus, development of an industrially feasible process for preparation of polymer/CNT conducting nanocomposites at very low CNT loading is essential prior to the commercialization of polymer/CNT nanocomposites. Here, we demonstrate a process technology that involves in situ bulk polymerization of methyl methacrylate monomer in the presence of multi‐wall carbon nanotubes (MWCNTs) and commercial poly(methyl methacrylate) (PMMA) beads, for the preparation of PMMA/MWCNT conducting nanocomposites with significantly lower (0.12 wt% MWCNT) percolation threshold than ever reported with unmodified commercial CNTs of similar qualities. Thus, a conductivity of 4.71 × 10^?5 and 2.04 × 10^?3 S cm^?1 was achieved in the PMMA/MWCNT nanocomposites through a homogeneous dispersion of 0.2 and 0.4 wt% CNT, respectively, selectively in the in situ polymerized PMMA region by using 70 wt% PMMA beads during the polymerization. At a constant CNT loading, the conductivity of the composites was increased with increasing weight percentage of PMMA beads, indicating the formation of a more continuous network structure of the CNTs in the PMMA matrix. Scanning and transmission electron microscopy studies revealed the dispersion of MWCNTs selectively in the in situ polymerized PMMA phase of the nanocomposites. Copyright © 2012 Society of Chemical Industry     

Dispersion of multi‐walled carbon nanotubes in poly(aryl ether ketone) obtained by in situ polymerization

BACKGROUND: Recently, much work has focused on the efficient dispersion of carbon nanotubes (CNTs) throughout a polymer matrix for mechanical and/or electrical matrices. However, CNTs used as enhancement inclusions in a high‐performance polymer matrix, especially in poly(aryl ether ketone) (PAEK), have rarely been reported. Therefore, multi‐walled carbon nanotube (MWNT)‐modified PAEK nanocomposites were synthesized by in situ polymerization of monomers of interest in the presence of pre‐treated MWNTs. RESULTS: This process enabled a uniform dispersion of MWNT bundles in the polymer matrix. The resultant MWNT/PAEK nanocomposite films were optically transparent with significant mechanical enhancement at a very low MWNT loading (0.5 wt%). CONCLUSION: These MWNT/polymer nanocomposites are potentially useful in a variety of aerospace and terrestrial applications, due to the combination of excellent properties of MWNTs with PAEK. Copyright © 2009 Society of Chemical Industry     

Electrical conductivity behavior of epoxy matrix nanocomposites with simultaneous dispersion of carbon nanotubes and clays

In this work, nanocomposites with simultaneous dispersion of multiwalled carbon nanotubes (MWCNT) and montmorillonite clays in an epoxy matrix were prepared by in situ polymerization. A high energy sonication was employed as the dispersion method, without the aid of solvents in the process. The simultaneous dispersion of clays with carbon nanotubes (CNT) in different polymeric matrices has shown a synergic potential of increasing mechanical properties and electrical conductivity. Two different montmorillonite clays were used: a natural (MMT‐Na⁺) and an organoclay (MMT‐30B). The nanocomposites had their electrical conductivity (σ) and dielectric constant (ε_r) measured by impedance spectroscopy. The sharp increase in electrical conductivity was found between 0.10 and 0.25 wt% of the MWCNTs. Transmission electron microscopy (TEM) of the samples showed a lower tendency of MWCNT segregation on the MMT‐30B clay surface, which is connected to intercalation/exfoliation in the matrix, that generates less free volume available for MWCNTs in the epoxy matrix. Data from electrical measurement showed that simultaneously adding organoclay reduces the electrical conduction in the nanocomposite. Moreover, conductivity and permittivity dispersion in low frequency suggest agglomeration of nanotubes surrounding the natural clay (MMT‐Na⁺) particles, which is confirmed by TEM. POLYM. COMPOS., 37:1603–1611, 2016. © 2014 Society of Plastics Engineers     

Efficient dispersion of multi‐walled carbon nanotubes by in situ polymerization

Multi‐walled carbon nanotube (MWNT)‐reinforced polyimide nanocomposites were synthesized by in situ polymerization of monomers in the presence of acylated MWNTs. The acyl groups associated with the MWNTs participated in the reaction through the formation of amide bonds. This process enabled uniform dispersion of MWNT bundles in the polymer matrix. The resultant MWNT–polyimide nanocomposite films were optically transparent with significant mechanical enhancement at a very low loading (0.5 wt%). Evidence has been obtained for improved interactions between the nanotubes and the matrix polymer. Copyright © 2006 Society of Chemical Industry     

Preparation of a functional reduced graphene oxide and carbon nanotube hybrid and its reinforcement effects on the properties of polyimide composites

The homogeneous dispersion and strong interfacial interactions of carbon nanomaterials are vital factors on enhancing the properties of polymer composites. Two‐dimensional reduced graphene oxide (rGO) and one‐dimensional carbon nanotubes (CNTs) were first grafted by 4,4′‐oxydianiline (ODA). The successful grafting of ODA onto the rGO and CNTs were confirmed by Fourier transform infrared spectroscopy, thermogravimetric analysis, and X‐ray photoelectron spectroscopy. The hybrid carbon nanomaterials of the functionalized CNTs and rGO with different ratios were prepared via a solution‐mixing method, and their dispersion state was investigated. The hybrid carbon nanomaterials with good stability were introduced to polyimide (PI) via in situ polymerization. The morphology and properties of the polymer composites were studied. The results show that much better mechanical and electrical properties of the composites could be achieved in comparison with those of the neat PI. An improvement of 100.7% on the tensile strength and eight orders for the electrical conductivity were achieved at only a 1.0 wt % hybrid content. A significant enhancement effect was attributed to the homogeneous dispersion of the filler, filler–matrix strong interfacial interactions, and unique structure of the hybrid carbon nanomaterials in the composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44575.     

Alignment and properties of carbon nanotube buckypaper/liquid crystalline polymer composites

Carbon nanotubes (CNTs) have been recognized as a potential superior reinforcement for high‐performance, multifunctional composites. However, non‐uniform CNT dispersion within the polymer matrix, the lack of adequate adhesion between the constituents of the composites, and lack of nanotube alignment have hindered significant improvements in composite performance. In this study, we present the development of a layer‐by‐layer assembly method to produce high mechanical performance and electrical conductivity CNT‐reinforced liquid crystalline polymer (LCP) composites using CNT sheets or buckypaper (BP) and self‐reinforcing polyphenylene resin, Parmax. The Parmax/BP composite morphology, X‐ray diffraction, mechanical, thermal, and electrical properties have been investigated. SEM observations and X‐ray diffraction demonstrate alignment of the CNTs due to flow‐induced orientational ordering of LCP chains. The tensile strength and Young's modulus of the Parmax/BP nanocomposites with 6.23 wt % multi‐walled carbon nanotube content were 390 MPa and 33 GPa, respectively, which were substantially improved when compared to the neat LCP. Noticeable improvements in the thermal stability and glass transition temperature with increasing CNT content due to the restriction in chain mobility imposed by the CNTs was demonstrated. Moreover, the electrical conductivity of the composites increased sharply to 100.23 S/cm (from approximately 10^?13 S/cm) with the addition of CNT BP. These results suggest that the developed approach would be an effective method to fabricate high‐performance, multifunctional CNT/LCP nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of CNT‐polyurethane nanocomposites using ester‐based polyols with different molecular structure: Mechanical,thermal, and electrical properties

Polyurethanes (PUs) were prepared by in situ polymerization of three diisocyanate with three synthesized low cost ester‐based polyols. The effect of diisocyanate type, diol structure, and molar ratio of diisocyanate to polyol on the mechanical properties was examined and the optimum chemical structure was introduced regarding the superior mechanical properties. Also, in presence of well dispersed hydroxylated multiwalled carbon nanotubes (CNT), PU/CNT nanocomposites were synthesized and fully characterized. The results showed that PU synthesized based on 1,4‐butane diol (BDO) has the best mechanical properties and thermal stability. Also, the PU samples synthesized from 1,6‐hexamethylene diisocyanate (HDI) were more profitable than aromatic diisocyanate structures due to higher crystallinity and microstructure packing. The nanocomposite sample containing 1.5% CNT was the optimum composition for the maximum tensile strength and electrical conductivity. This result was related to the uniform dispersion and bonding of CNTs to PU chains at this composition, while aggregates were formed at higher concentration of CNTs which increased the defects and reduced the uniformity of the structure. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44567.     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study on the properties of multi-walled carbon nanotubes reinforced poly (vinyl alcohol) composites

Nanocomposite films based on polyvinyl alcohol(PVA) and multi-walled carbon nanotubes (MWCNTs) at different weight ratios (i.e.0.0,0.5, 1.0,1.5, 2.0 wt%), were prepared by dispersion techniques. Cationic geminisurfactant and its monomeric form (0.01 wt%) were used as dispersants to achieve homogeneous and stable dispersionof CNTs in water and subsequent PVA/CNTs nanocomposites. Surface charge of CNTs in aqueous suspension with addition of the used dispersants were investigated by measuring its zeta potential. The structural and interaction studies have been analyzed from X-ray diffraction (XRD) and Raman spectroscopy. The effect of the used surfactantson the separation and distribution of CNTs in PVA matrix was studied by visual characterization based on scanning electron microscopy (SEM). Thermal, mechanical and electrical properties of the prepared nanocomposites were evaluated and the results were discussed in relation with the CNTs content and surfactant type as dispersant. Surfactant effect improved the dispersion homogeneity of CNTs (at 1.0 wt%) within the polymer matrix. The physical interaction between. CNTs and PVA macromolecular chains resulting in nanocomposites with largely enhanced properties compared to those prepared with higher filler loading by avoiding the agglomeration phenomenon of nanotubes. On the other hand, the addition of CNTs by content up to 2 wt%, increases the electrical conductivity to be 10^?6 Scm^?1 at room temperature which highly recommends such composites to be used in electrostatic dissipation applications upon using gemini surfactant. Furthermore, useful nanosized capacitor structure based onnanocomposites containing its monomeric form, characterized by high permittivity and low dielectric loss, can be formed.     

Thermal and thermomechanical behavior of amino functionalized and metal decorated MWCNTs/PMMA nanocomposite films

The homogeneous nanocomposites (NC) films of amino modified and metal decorated multiwall carbon nanotubes (MWCNTs) with polymethylmethacrylate (PMMA) were synthesized through in‐situ free radical polymerization. Silver metal nanohybrids (Ag/MWCNTs) were prepared by two strategies, that is, reduction of metal salt in presence of sodium dodecyl sulfate and in‐situ growth from AgNO₃ aqueous solution. The amino functionalization by ball milling enhanced the dispersion of MWCNT in monomer and produced a new class of radiation resistant NC. These synthesized films were characterized by FTIR, TGA, TEM, EDX, TC, DMA, and optical microscopy to ascertain their structural morphologies, thermal stability, and mechanical strength. Microscopic studies reflect the homogeneous mixing of amino functionalized and metal decorated MWCNTs in polymer matrix contributing in the enhancement of thermal stability, thermo‐mechanical strength, glass transition temperatures, and thermal conductivity of NC even at 0.25 wt% addition of modified nanofiller. The thermal stability of NC film at 0.25 wt% loading was increased around ≂50°C and the raise of thermo‐mechanical properties was observed up to 85% at 100°C in the presence of adsorbed surfactant. Thermal and thermomechanical behavior of pre and post UV/O₃ irradiated NC films has been compared with neat polymer. The results revealed that amino modified nanofiller embedded network in polymer matrix can effectively disperse the radiation and has a dramatic reinforcement effect on the nature of degradation of PMMA matrix. POLYM. COMPOS., 35:1807–1817, 2014. © 2013 Society of Plastics Engineers     

From carbon nanotube coatings to high‐performance polymer nanocomposites

Since their discovery at the beginning of the 1990s, carbon nanotubes (CNTs) have been the focus of considerable research by both academia and industry due to their remarkable and unique electronic and mechanical properties. Among numerous potential applications of CNTs, their use as reinforcing materials for polymers has recently received considerable attention since their exceptional mechanical properties, combined with their low density, offer tremendous opportunities for the development of fundamentally new material systems. However, the key challenge remains to reach a high level of nanoparticle dissociation (i.e. to break down the cohesion of aggregated CNTs) as well as a fine dispersion upon melt blending within the selected matrices. Therefore, this contribution aims at reviewing the exceptional efficiency of CNT coating by a thin layer of polymer as obtained by an in situ polymerization process catalysed directly from the nanofiller surface, known as the ‘polymerization‐filling technique’. This process allows for complete destructuring of the native filler aggregates. Interestingly enough, such surface‐coated carbon nanotubes can be added as ‘masterbatch’ in commercial polymeric matrices leading to the production of polymer nanocomposites displaying much better thermomechanical, flame retardant and electrical conductive properties even at very low filler loading. Copyright © 2007 Society of Chemical Industry     

Poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) multi-bonded carbon nanotube (CNT): Preparation and formation of PPO/CNT nanocomposites

Poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) multi-bonded carbon nanotube (CNT) (CNT-PPO) was prepared using brominated PPO under the condition of atom transfer radical polymerization. The structure and properties of CNT-PPO were characterized with FTIR, Raman spectroscopy and thermal analyzer. The PPO layer in a thickness of about 4.5 nm was observed covering on the side wall of CNT with a high-resolution TEM. The PPO modification warrants the good dispersion of CNTs in PPO in the formation of PPO/CNT nanocomposites, which demonstrated enhanced mechanical properties and increases in electrical conductivity. The developed approach of CNT modification with engineering plastics can be applied to other polymers and preparation of functional polymer/CNT nanocomposites.     

Electrical and mechanical behaviors of carbon nanotube‐filled polymer blends

Four carbon nanotube (CNT)‐filled polymer blends, i.e., CNT‐filled polyethylene terephthalate (PET)/polyvinylidene fluoride, PET/nylon 6,6, PET/polypropylene, and PET/high‐density polyethylene blends, have been injection‐molded and characterized in terms of their microstructures, electrical conductivities, and mechanical properties. The distribution of CNTs in the polymer blends has been examined based on their wetting coefficients and minimization of the interfacial energy. The electrical conductivity and mechanical properties have been related to the cocontinuous polymer blends, the conductive path formed by CNTs, the CNT distribution, and the intrinsic properties of the constituent polymers. It is found that to obtain a CNT‐filled polymer composite with both high electrical conductivity and good mechanical properties, it is preferred that most CNTs distribute in one polymer phase, while the other polymer phase(s) remain neat. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 477–488, 2006     

Polyimide‐carbon nanotubes nanocomposites: electrical conduction behavior under cryogenic condition

This study is aimed to investigate the electrical conduction behavior of polyimide (PI)/multiwall carbon nanotubes (CNTs) nanocomposites in cryogenic environment (temperature from 10 to 300 K) prepared by in situ polymerization technique. The experimental results of direct current (DC) electrical conductivity have been fitted with different theoretical models to check their applicability and to understand the conduction behavior for the present nanocomposite system. The PI/CNT nanocomposites show low electrical percolation threshold. Negative temperature coefficient effect of resistivity is observed for all the composites under investigation. The analysis shows that Mott's variable range hopping (VRH) model is more applicable compared to Arrhenius and Kivelson models for the present composites over the entire range of measurement temperature. The electronic transport behavior in each composite at temperature above 70 K can be ascribed to thermally activated tunneling of charge carriers through insulating barriers between CNTs; however, the electronic transport behavior at temperature below 70 K can be attributed to three dimensional VRH of charge carriers through the networks of CNTs in the polymer composite. The current–voltage characteristics of the composite show non‐ohmic behavior for temperature below 60 K and become ohmic in nature as temperature rises to 300 K. POLYM. ENG. SCI., 57:291–298, 2017. © 2016 Society of Plastics Engineers     

Structure‐property relationship of substituted pyrrolidine functionalized CNT epoxy nanocomposite

Carbon nanotubes (CNTs) based polymer nanocomposites hold the promise of delivering exceptional mechanical properties and multifunctional characteristics. However, the realization of exceptional properties of CNT based nanocomposites is dependent on CNT dispersion and CNT‐matrix adhesion. To this end, we modified MWCNTs by Prato reaction to yield aromatic (phenyl and 2‐hydroxy‐4‐methoxyphenyl) substituted pyrrolidine functionalized CNTs (fCNT1 and fCNT2) and aliphatic (2‐ethylbutyl and n‐octyl) substituted pyrrolidine functionalized CNTs (fCNT3 and fCNT4). The functionalization of CNTs was established by Thermogravimetric analysis (TGA), Raman Spectroscopy, and XPS techniques. Optical micrographs of fCNT epoxy mixture showed smaller aggregates compared to pristine CNT epoxy mixture. A comparison of the tensile results and onset decomposition temperature of fCNT/epoxy nanocomposite showed that aliphatic substituted pyrrolidine fCNT epoxy nanocomposites have higher onset decomposition temperature and higher tensile toughness than aromatic substituted pyrrolidine fCNT epoxy nanocomposites, which is consistent with the dispersion results of fCNTs in the epoxy matrix. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42284.     

Ultrasound assisted twin screw extrusion of polymer-nanocomposites containing carbon nanotubes

The unique morphology and strong intertube attraction between carbon nanotubes (CNTs) make the dispersion of CNTs challenging and hence limit its effective use. A novel method for the continuous dispersion of multi-walled carbon nanotubes (MWNTs) in a polymer matrix for manufacturing high performance nanocomposites was developed using an ultrasonically assisted twin screw extrusion process. Reduction of the die pressure and variation of the ultrasonic power consumption as a function of amplitude were measured at various MWNT loadings. The effect of ultrasound on rheological, electrical, morphological and mechanical properties of polyetherimide (PEI) matrix and PEI-filled with 1-10 wt% MWNTs was studied. In the treated nanocomposites, the complex viscosity, storage and loss moduli were increased and damping characteristics were decreased as compared to untreated ones. Rheological and electrical percolations were found to be between 1 and 2 wt% MWNT loading. Ultrasonic treatment does not affect the electrical conductivity of nanocomposites. Mechanical properties such as Young's modulus and tensile strength were significantly increased with MWNT loading but moderately with ultrasonic treatment at high loadings and certain ultrasonic amplitudes. The morphology and state of dispersion of MWNTs were investigated by means of HRSEM. In the ultrasonically treated nanocomposites, the obtained micrographs showed excellent dispersion of MWNTs in PEI matrix.     

The effect of fluorosilicone modifiers on the carbon nanotube networks in epoxy matrix

Structure and properties of polymer compositions based on carbon nanotubes (CNTs) filled epoxy matrix containing fluorosilicone copolymers as additives is discussed. Electrical conductivity and dielectric (microwave) permittivity of the composites can be varied by approximately one order of magnitude without changing the CNT concentration, by careful selection of the additive type and concentration. The mutual solubility of the modifiers and epoxy is a key factor determining both rheological properties of the uncured compositions and electrical properties of cured CNT‐nanocomposites. CNT‐nanocomposites modified with amino‐functional (i.e., epoxy crosslinkable) copolymers demonstrate improved electrical conductivity values at increased additive concentration, connected with the formation of specific segregated microstructure. Fluorosilicone additives added in a specific amount also allow for a decrease of the viscosity of uncured epoxy CNT‐nanocomposites, improving their processability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46539.     

In situ polymerization of polyimide‐based nanocomposites via covalent incorporation of functionalized graphene nanosheets for enhancing mechanical,thermal, and electrical properties

In this study, we report an effective method to fabricate high‐performance polyimide (PI)‐based nanocomposites using 3‐aminopropyltriethoxysilane functionalized graphene oxide (APTSi‐GO) as the reinforcing filler. APTSi‐GO nanosheets exhibit good dispersibility and compatibility with the polymer matrix because of the strong interfacial covalent interactions. PI‐based nanocomposites with different loadings of functionalized graphene nanosheets (FGNS) were prepared by in situ polymerization and thermal imidization. The mechanical performance, thermal stability, and electrical conductivity of the FGNS/PI nanocomposites are significantly improved compared with those of pure PI by adding only a small amount of FGNS. For example, a 79% improvement in the tensile strength and a 132% increase in the tensile modulus are achieved by adding 1.5 wt % FGNS. The electrical and thermal conductivities of 1.5 wt % FGNS/PI are 2.6 × 10^?3 S/m and 0.321 W/m·K, respectively, which are ～10¹⁰ and two times higher than those of pure PI. Furthermore, the incorporation of graphene significantly improves the glass‐transition temperature and thermal stability. The success of this approach provides a good rationale for developing multifunctional and high‐performance PI‐based composite materials. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42724.     

Mechanical,thermal and electrical properties of multi‐walled carbon nanotube/aluminium nitride/polyetherimide nanocomposites

A series of polyimide‐based nanocomposites containing polyimide‐grafted multi‐walled carbon nanotubes (PI‐g MWCNTs) and silane‐modified ceramic (aluminium nitride (AlN)) were prepared. The mechanical, thermal and electrical properties of hybrid PI‐g MWCNT/AlN/polyetherimide nanocomposites were investigated. After polyimide grafting modification, the PI‐g MWCNTs showed good dispersion and wettability in the polyetherimide matrix and imparted excellent mechanical, electrical and thermal properties. The utilization of the hybrid filler was found to be effective in increasing the thermal conductivity of the composites due to the enhanced connectivity due to the high‐aspect‐ratio MWCNT filler. The use of spherical AlN filler and PI‐g MWCNT filler resulted in composite materials with enhanced thermal conductivity and low coefficient of thermal expansion. Results indicated that the hybrid PI‐g MWCNT and AlN fillers incorporated into the polyetherimide matrix enhanced significantly the thermal stability, thermal conductivity and mechanical properties of the matrix. Copyright © 2012 Society of Chemical Industry