Oil-Lubricated Fretting Behaviors of 304 Stainless Steels under Different Fretting Strokes and Normal Loads

The influence of oil lubrication on the fretting wear behaviors of 304 stainless steel flat specimens under different fretting strokes and normal loads has been investigated. The results proved that fretting regimes and fretting wear behaviors of 304 stainless steels were closely related to the fretting conditions. In general, the increase in normal load could increase wear damage during sliding wear. However, according to the results, a significant reduction in wear volume and increase in friction coefficient was observed when the normal load was increased to critical values of 40 and 50 N at a fretting stroke of 50 μm due to the transformation of the fretting regime from a gross slip regime to partial slip regime. Only when the fretting stroke further increased to a higher value of 70 μm at 50 N, fretting could enter the gross slip regime. There was low wear volume and a high friction coefficient when fretting was in the partial slip regime, because oil penetration was poor. The wear mechanisms were fatigue damage and plastic deformation. There was high wear volume and low friction coefficient when fretting was in the gross slip regime, because the oil could penetrate into the contact surfaces. Unlike the wear mechanisms in the partial slip regime, fretting damage of 304 stainless steels was mainly caused by abrasive wear in the gross slip regime.     

Fretting wear behaviors of steel wires under friction-increasing grease conditions

Fretting wear tests were performed on the self-made fretting wear rig to investigate fretting wear behaviors of steel wires under friction-increasing grease conditions. The results demonstrated that the fretting regimes were dependent on displacement amplitudes and normal loads. The friction coefficient exhibited different variation trends in different fretting regimes. Friction-increasing grease changed the fretting running behavior and had a very good wear resistance for steel wires. Wear was slight in partial slip regime. Mixed regime was characterized by plastic deformation, fatigue cracks and abrasive wear. Slip regime presented main damage mechanisms of abrasive wear, fatigue wear and oxidation.     

Modeling of fretting wear evolution in rough circular contacts in partial slip

This paper presents a numerical model that maps the evolution of contact pressure and surface profile of Hertzian rough contacting bodies in fretting wear under partial slip conditions. The model was used to determine the sliding distance of the contacting surface asperities for one cycle of tangential load. The contact pressure and sliding distance were used with Archard's wear law to determine local wear at each surface asperity. Subsequently, the contact surface profile was updated due to wear. The approach developed in this study allows for implementation of simulated and/or measured real rough surfaces and study the effects of various statistical surface properties on fretting wear. The results from this investigation indicate that an elastic–perfectly plastic material model is superior to a completely elastic material model. Surface roughness of even small magnitudes is a major factor in wear calculations and cannot be neglected.     

基于双重扩展自适应卡尔曼滤波的汽车状态和参数估计

准确实时地获取行驶过程中的状态信息是汽车动态控制系统研究的关键,为此提出了一种新的汽车状态估计器。建立了包含不准确模型参数和未知时变统计特性噪声的非线性汽车动力学模型,针对该非线性系统提出一种双重扩展自适应卡尔曼滤波算法（DEAKF）。该算法采用两个卡尔曼滤波器并行运算,状态估计和参数估计互相更新,同时将带遗忘因子的噪声统计估值器嵌入到状态校正过程和参数校正过程之间,以解决系统的噪声时变问题。基于ADAMS的虚拟试验和实车试验结果表明,该算法的状态估计精度高于EKF方法和DEKF方法的状态估计精度,同时具有良好的模型参数校正能力,对汽车动态控制系统中估计器的设计具有理论指导意义。
     

The effect of gross sliding fretting wear on stress distributions in thin W-DLC coating systems

The effect of fretting wear on stress evolution in a thin, hard diamond-like carbon coating deposited on a high strength steel is simulated using a finite element (FE) based method under gross sliding conditions. The effects of coating stiffness, thickness, and coefficient of friction are studied. The trailing edge tensile stress and the leading edge compressive stress are generally predicted to reduce with wear, while the shear stress at the interface is predicted to increase. An extrapolation procedure for predicting coating wear life is shown to provide accurate and slightly conservative estimates compared with explicit modelling to complete coating wear.     

Research on torsional fretting wear behaviors and damage mechanisms of stranded-wire helical spring

Wear on the local area of steel wires’ surface is attributed to torsional fretting on the working process of stranded-wire helical spring. A mathematical model to calculate normal contact force and angular displacement amplitude among the wires is established first when the spring is impacted. With the experimental parameters obtained from the model, the torsional fretting test, which stimulates torsional fretting among the wires in the working process of the spring, is realized successfully on a newly developed fretting tester. Torsional fretting behaviors are strongly dependent upon normal contact force, angular displacement amplitude, and number of cycles. There are three basic types of T-θ curves (short for torque), angular displacement curves during the process of torsional fretting, namely, parallelogram, elliptic, and linear T-θ curves. To analyze the damage mechanisms, distribution maps of oxygen in the wear scar of spring wires under different working conditions are revealed. The damage gets slight in the partial slip region, mainly with the abrasive wear and the slight oxidative wear, whereas the wear mechanisms are mainly the abrasive wear, the oxidative wear, and the delamination, accompanied with obvious plastic deformation in the mixed fretting and slip regions.

     

中性腐蚀环境下钢丝的微动疲劳行为

在自制的微动疲劳试验机上开展中性腐蚀环境下单根钢丝的微动疲劳实验,考察在相同接触载荷下,不同振幅对钢丝的微动疲劳行为的影响,并用扫描电子显微镜观察疲劳钢丝的磨痕和断口形貌,研究钢丝微动疲劳断裂机制.结果表明:在较大的振幅下,钢丝的微动区均处于滑移状态,而在较小振幅下,钢丝的微动区从滑移状态逐渐转变为黏着状态;磨损机制主要为磨粒磨损、疲劳磨损、腐蚀磨损和塑性变形;钢丝疲劳寿命随着微动振幅的增大而减小;钢丝的疲劳断口可分为3个区域,即疲劳源区、裂纹扩展区及瞬间断裂区.     

Fretting wear of carburized titanium alloy against ZrO2 under serum lubrication

Fretting wear of carburized titanium alloys was investigated on the universal multifunctional tester (UMT) with the ball-on-flat fretting style under bovine serum lubrication. The tangential load and friction coefficient during the fretting process were analyzed, and the evolution of fretting log during the fretting process was investigated to understand the wear mechanism of the titanium alloy and carburized titanium alloy. Furthermore, the wear scar was examined using a SEM and three-dimension surface profiler. It was found that the friction coefficient of the titanium alloy increased faster than that of carburized titanium alloy in the first stage under serum lubrication, and then remained steady with a similar value in the second stage. The Ft-D curve indicated that there was wear mechanism transition from gross slip to mixed stick and slip. Finally, it was observed that there was a slight damage of the titanium alloy and carburized titanium alloy showed excellent performance during the fretting wear process under serum lubrication. All of the results suggested that carburized titanium alloy was a potential candidate for the stem material in artificial joints.     

Fretting Wear Behavior of UHMWPE—Influence of Load and Stroke

In this study, the tribological behavior of ultra-high-molecular-weight polyethylene (UHMWPE) against a GCr 15 steel ball during fretting wear conditions was investigated using an oscillating reciprocating tribometer. The aim of this study was to characterize the critical value of normal load and stroke corresponding to this transition in UHMWPE worn surface at room temperature. Results showed that there existed a critical value of load or stroke at fixed condition. The friction coefficient and wear volume loss of UHMWPE at or near the critical values of load and stroke exhibited extreme changes. Based on observation of the worn surface by scanning electron microscopy (SEM) and 3D surface profiler measurements, it can be found that damage to the worn surface can be linked to the contact load and stroke. In addition, results showed that during the process of fretting wear under different load or stroke conditions, the gross slip regime dominated throughout the whole test period.     

Development of a test device for the evaluation of fretting in point contact

Fretting wear and fatigue may occur between any two contacting surfaces, wherever short‐amplitude reciprocating sliding is present for a large number of cycles. A test device has been developed for the evaluation of fretting fatigue and wear in partial and gross slip conditions. Three similar sphere‐on‐plane contacts run at the same time. Normal force, tangential force or displacement amplitude and constant bulk stress can be controlled and measured separately. Reciprocating tangential displacement is produced with rotational motion, the amplitude and frequency of which can be adjusted and controlled accurately by an electric shaker. The number of load cycles for crack initiation and growth is determined with strain‐gauge measurements near the fretting point of contact. The contact surfaces are measured with 3D optical profilometer before fretting measurements to determine actual contact geometry. The measurements were done with quenched and tempered steel. The initial results indicate that cracks are mostly formed in partial slip conditions, whereas fretting wear is more heavily involved in gross slip conditions. The initiation of a crack occurs near the edge of the contact in the slip direction, where the calculated cracking risk has its maximum value in partial slip conditions. The number of cracks increases as the displacement amplitude, i.e. friction force, increases in partial slip conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

电连接器微动磨损的超声识别与性能退化模型

针对振动环境下电连接器易产生微动磨损而接触性能降低这一问题，采用超声检测方法监测微动磨损过程中电连接器接触件间磨屑的特征值，研究了不同振动条件下接触件的磨损程度及接触性能的退化规律。结果表明，振动频率、振动加速度和振动次数对接触面磨屑的堆积和接触电阻的波动都有正向累积效应；电连接器轴向振动时，磨屑累积效应最为明显。接触电阻和磨屑特征值总量在高振频及加速度下呈现极高的相关性。以磨屑特征值构建的麻雀搜索算法优化BP神经网络性能退化模型的平均绝对误差小于5%。     

690合金材料的微动磨损特性研究

利用微动磨损试验机,在载荷50N以及位移幅值为60μm、100μm、150μm的工况下,研究了690合金材料在常温下的微动磨损行为及其动力学特性,采用激光共焦扫描显微镜(LCSM)和扫描电子显微镜(SEM)观察磨痕微观形貌。结果表明,载荷和位移幅值对微动特征有很大的影响,微动运行完全处于滑移状态。在滑移区,滑移磨损严重、磨痕面积大。690合金材料的磨损机制主要表现为磨粒磨损与剥层的共同作用。     

轿车轮毂轴承微动磨损试验分析

利用自行设计的轿车轮毂轴承径向式微动磨损试验系统,对三组轮毂轴承进行试验。试验轴承滚道上出现宏观条状磨损痕迹,轴承次表面约20 ?m处出现了连续微孔,严重微动磨损的轴承次表面出现了近似平行于滚道的微裂纹。同时,模拟径向载荷下轮毂轴承的内部3D应力分布,结果表明,轮毂轴承载荷区出现条状应力/应变峰的幅值波动。在此基础上,结合轿车行驶时轮毂轴承的承载特点,提出了轮毂轴承广义复合微动磨损机理模型。该模型为减缓轮毂轴承微动磨损程度和提高轴承可靠性提供了新的途径。     

粘结MoS2固体润滑涂层的转动微动磨损特性

采用粘结法在LZ50钢表面制备MoS2固体润滑涂层,研究MoS2涂层及LZ50钢基体在干态不同角位移幅值下的转动微动磨损行为。在分析转动微动动力学特性的同时,结合光学显微镜、扫描电子显微镜、电子能谱仪以及轮廓仪对磨痕形貌进行微观分析。结果表明:涂层和基体的转动微动运行区域仅呈现部分滑移区(Partial slip regime,PSR)和滑移区(Slip regime,SR),未观察到混合区。涂层改变基体的微动运行区域,使得PSR缩小,SR运行区域向小角位移幅值方向移动。由于MoS2涂层的固体润滑作用,涂层的摩擦因数在整个试验过程都明显低于基体。在PSR,涂层损伤轻微;在SR,涂层的转动微动磨损机制主要表现为剥层和摩擦氧化。研究表明粘结MoS2固体润滑涂层具有明显的防护作用,显著降低LZ50钢的转动微动磨损。     

Fretting wear behavior of superelastic nickel titanium shape memory alloy

The fretting behavior of superelastic nickel titanium (NiTi) shape memory alloy was studied at various displacement amplitudes on a serve-hydraulic dynamic test machine. The results showed that the superelastic properties of the material played a key role in the observed excellent fretting behavior of NiTi alloy. Due to the low phase transition stress (only 1/4 the value of its plastic yield stress) and the large recoverable phase transition strain (5%) of NiTi, the friction force of NiTi/GCr15 stainless steel pair is smaller than the value of GCr15/GCr15 pair and at the same time the Rabinowicz wear coefficient of NiTi plate is about 1/9 the value of GCr15 plate under the same fretting conditions. For NiTi/GCr15 pair, even NiTi has a much lower hardness than GCr15, the superelastic NiTi alloy exhibits superior fretting wear property than GCr15 steel. It was found that the weak ploughing was the main wear mechanism of NiTi alloy in the partial slip regime. While in the mixed regime and gross slip regime, the wear of NiTi was mainly caused by the abrasive wear of the GCr15 debris in the three-body wear mode.     

金属橡胶内螺旋金属丝微动磨损预测模型研究*

目前金属丝微动磨损预测模型多适用于垂直接触，而锐角交叉下的模型存在计算过程繁琐、表征不全面等不足，难以便捷有效地预测金属橡胶内部复杂无序的金属丝磨损情况。基于有限元分析，确定螺旋曲率对磨损结果的影响极小，因此将金属橡胶内部螺旋金属丝接触对微元理想化为直金属丝接触对，探究无序接触下金属丝磨损特征的演化规律。结果表明，无序接触状态下的磨损特征演化规律与金属丝接触夹角大小密切相关。依据几何学分析，得到任意锐角接触下磨损磨痕位于金属丝1/2接触夹角处的特殊位置关系，据此建立任意接触形态下的微动磨损演化预测模型，并利用已有文献中的金属丝微动磨损试验结果对预测模型进行验证。结果显示，建立的任意锐角下的磨损演化模型能够较准确地预测金属丝的磨损结果，误差均在15%以内。研究结果为预测金属橡胶内部金属丝微动磨损和使用寿命提供一定理论基础。     

钛合金球与骨水泥界面之间的微动磨损机制研究

采用钛合金球与自制骨水泥试样以球/平面接触方式,在自制的微动摩擦磨损试验机上开展干摩擦和25%小牛血清介质中切向微动磨损试验研究,考察钛合金球与骨水泥界面之间的微动运行特性,并采用S-3000N型扫描电镜观察磨痕形貌来分析其微动磨损机制。结果表明:随着微动振幅的增加,微动运行由部分滑移区向混合区转变。随着接触载荷的增加,试样接触面之间更容易发生黏着。与干摩擦相比,在小牛血清溶液中部分滑移区向较大振幅区扩展。部分滑移区摩擦因数值较低且保持稳定,混合区的摩擦因数先增大后保持不变。稳定摩擦因数随着接触载荷的增加而减小,随微动振幅增大而增大。骨水泥试样的磨损量在小牛血清介质中比在空气中大,并且随接触载荷增大而增大。骨水泥在小牛血清介质中微动磨损的损伤机制主要为黏着磨损和疲劳磨损,溶液分子在应力作用下对骨水泥基体有削弱作用。     

不锈钢焊接区金属微动磨损行为研究

以1Cr18Ni9Ti不锈钢材料为母材,采用焊条电弧焊方法制备焊件。在焊接检验合格的焊态试件上从焊缝区、熔合区和焊接热影响区金属中分别截取并制备微动磨损试验用试样。将制备好的焊接区不同位置金属试样在相同条件下进行微动磨损试验,研究焊接区金属微动磨损行为。研究结果表明,在选定的微动磨损试验参数下,微动处在完全滑移区;焊接区不同部位金属的微动磨痕形貌存在差异,具有不同的微动磨损行为。焊缝区金属磨痕最大深度差异不明显,但磨痕平面投影面积差异显著。焊接热影响区金属磨痕最大深度差异显著,而磨痕平面投影面积差异不明显。     

AZ91D镁合金微动磨损特性研究

采用液压高精度材料试验机考察了平面一球面接触的AZ91D镁合金摩擦副的微动磨损行为，分析了位移幅值、法向载荷和频率等参数对摩擦因数和磨损体积的影响，考察了不同实验条件下的磨斑形貌，并探讨了其磨损机理。结果表明：AZ91D镁合金的微动区域可分为部分滑移区、混合区和滑移区3个区域，粘着磨损、疲劳磨损和磨粒磨损分别是3个区域的主要磨损机制；磨损体积随着位移幅值和法向载荷的增加而增大，但却随着频率的增大而减小。在微动部分滑移区和混合区，摩擦因数随着位移增大迅速增加；在微动滑移区，摩擦因数随法向载荷的增大而减小，而位移幅值和频率对摩擦因数的影响较小。     

Measurement, analysis and prediction of fretting wear damage in a representative aeroengine spline coupling

A methodology to predict fretting wear in complex couplings is described and validated against results obtained from a reduced scale aeroengine-type spline coupling subjected to complex cyclic load cases. The methodology uses three-dimensional finite element analysis, together with coefficient of friction data obtained from stroke controlled round-against-flat fretting tests, to determine spline tooth contact pressure and slip distributions; the latter as a function of number of loading cycles. A modified Archard equation is used to calculate wear depths from the contact pressure and slip distributions using wear coefficients obtained from the round-against-flat fretting tests. The slip distributions, and, concomitantly, the wear distributions, are found to depend strongly on the coefficient of friction, which, in turn, depends on the state of lubrication and number of loading cycles. For constant coefficient of friction, the slip distributions stabilise quickly with increasing numbers of loading cycles. The methodology predicts greater wear under lightly lubricated conditions than without added lubrication for the essentially load-controlled tests on the reduced scale aeroengine-type coupling. The wear depth trends are predicted correctly, both axially along the spline teeth and around the tooth flank, and the predicted wear depths bracket the measured values, dependent on the lubrication conditions considered; the latter attributable to the sensitivity of spline wear to the evolving coefficient of friction during testing. The methodology provides a basis for further development.