Dy2 AlFe13 Mn3 化合物的本征磁致伸缩

通过X-射线衍射及磁测量手段研究了Dy2AlFe13Mn3化合物的结构及磁性质。研究结果表明Dy2AlFe13Mn3化合物具有六角相的Th2Ni17型结构。通过X-射线热膨胀测定法发现Dy2AlFe13Mn3化合物在245到344K的温度范围内存在负热膨胀现象，其平均热膨胀系数为α＝-1.1×10-4K-1K-1。在105到360K的温度范围内，通过比较磁性状态下的晶胞参数和由高温顺磁状态外延得到的低温顺磁状态下的晶胞参数间的差别计算了Dy2AlFe13Mn3化合物的本征磁致伸缩。结果表明Dy2AlFe13Mn3化合物的本征体磁致伸缩ωS在105到245K的温度范围内随着温度的升高而增大，由105K时的7.0×10-3 增加到245K时的9.1×10-3。随着温度的进一步升高，ωS反而减小。沿c轴方向的本征线磁致伸缩λc随着温度的升高而减小。基面内的本征线磁致伸缩λa在105到270K的温度范围内随着温度的升高而增大，从105K时的0.8×10-3增大到270K时的3.4×10-3，然后随着温度的进一步升高而减小。     

Tb2Fe15.5Cr1.5化合物的本征磁致伸缩

通过x射线衍射及磁测量手段研究了Tb₂Fe_15.5Cr_1.5化 合物的热膨胀性质及本征磁致伸缩性质.研究结果表明Tb₂Fe_15.5Cr _1.5化合物在293—672K的温度范围内具有六角相的Th₂Ni_{17型结构.在432—522K的温度范围内具有负热膨胀 性质，其平均热膨胀系数=-157×10^-5/K.对本征磁致伸缩的研究结果表明Tb2Fe15.5Cr1.5化合物中存在着较强的各向异性的本 征磁致伸缩，293K时其本征体磁致伸缩约为84×10^-3，晶格畸变主要发生在c 轴方向上.磁测量研究结果表明Tb2Fe15.5Cr1.5化合物的居里温度约为494K，比其母 合金Tb2Fe17高约80K.}     

Ho2AlFe14Mn2化合物的负热膨胀性质

利用x射线衍射及磁测量手段研究了Ho2AlFe16-xMnx系列化合物的结构.结果表明，该系列化合物具有Th2Ni17型结构；随着x的增加，化合物的单胞体积呈现非线性的变化，结合磁测量结果分析认为，在化合物的磁相变点附近存在较大的正的本征磁致伸缩.在160—285K温度范围内对Ho2AlFe14Mn2化合物进行的变温x射线衍射研究表明，该化合物在其居里点附近(220—270K)具有负热膨胀性质，其平均热膨胀系数为-14×10-4/K. 关键词： Ho2AlFe16-xMnx化合物 负热膨胀 本征磁致伸缩     

Mn替代对Dy2AlFe16-xMnx化合物的结构和磁性的影响

通过X射线衍射及磁测量手段研究了Dy2AlFe16-xMnx化合物的结构和磁性.研究结果表明Dy2AlFe16-xMnx化合物具有六角相的Th2Ni17型结构.对x=1,2的样品采用X射线热膨胀测定法在104-647K的温度范围内测量了其热膨胀性质,发现这些化合物在低温下存在热膨胀反常现象,在居里点附近出现负膨胀性质.对自发磁致伸缩的研究结果表明Dy2AlFe16-xMnx化合物中存在着较强的各向异性的自发磁致伸缩,随着Mn含量的增加,其低温下的自发体磁致伸缩减弱.磁测量结果表明Mn的替代导致Dy2AlFe16-xMnx化合物的居里温度及自发磁化强度急剧下降.     

Er2AlFe16－xMnx化合物的磁性及反常热膨胀

通过X射线衍射及磁测量手段研究了Er₂AlFe_16-xMn_x(x=1，2，3，4，6，8)化合物的结构和磁性. 研究结果表明Er₂AlFe_16-xMn_x化合物具有六角相的Th₂Ni₁₇型结构. 采用X射线热膨胀测定法在103—654K的温度范围内测量了Er₂AlFe_16-xMn_x(x=1，2，3，4)化合物的热膨胀性质，发现这些化合物在低温下存在热膨胀反常现象，在居里点附近具有负膨胀性质. 对自发磁致伸缩的研究结果表明Er₂AlFe_16-xMn_x化合物中存在着较强的各向异性的自发磁致伸缩，低温下自旋重取向的出现使得化合物的自发体磁致伸缩有所增强. 磁测量结果表明Mn的替代导致Er₂AlFe_16-xMn_x化合物的居里温度及自发磁化强度急剧下降，并且使得化合物的磁晶各向异性发生显著改变. 关键词： 2AlFe_16-xMn_x化合物')" href="#">Er₂AlFe_16-xMn_x化合物 反常热膨胀 自发磁致伸缩     

Mn替代对Dy2AlFe16－xMnx化合物的结构和磁性的影响

通过X射线衍射及磁测量手段研究了Dy₂AlFe_16-xMn_x化 合物的结构和磁性.研究结果表明Dy₂AlFe_16-xMn_x化合 物具有六角相的Th₂Ni₁₇型结构.对x=1，2的样品采用X射线热膨胀 测定法在104—647K的温度范围内测量了其热膨胀性质，发现这些化合物在低温下存在热膨 胀反常现象，在居里点附近出现负膨胀性质.对自发磁致伸缩的研究结果表明Dy₂AlFe_16-xMn_x化合物中存在着较强的各向异性的自发磁致伸缩，随 着Mn含量的增加，其低温下的自发体磁致伸缩减弱.磁测量结果表明Mn的替代导致Dy_{2< /sub>AlFe16-xMnx化合物的居里温度及自发磁化强度急剧下降. 关键词： 2}AlFe_16-xMn_x化合物')" href="#">Dy₂AlFe_16-xMn_x化合物 反常热膨胀 自发磁致伸缩 自发磁化强度     

Tb0.3Dy0.7(Fe1-xAlx)1.95合金的磁致伸缩、自旋重取向和穆斯堡尔谱研究

系统研究了室温下Tb0.3Dy0.7(Fe1-xAlx)1.95(x=0,0.05,0.1,0.15,0.2,0.25,0.3,0.35)合金中金属Al替代Fe对晶体结构、磁致伸缩、各向异性和自旋重取向的影响.结果发现,x<0.4时,Tb0.3Dy0.7(Fe1-xAlx)1.95完全保持MgCl2立方Laves相结构,晶格常量a随Al含量x的增加而增大.磁致伸缩测量发现,随着替代量x的增多磁致伸缩减小,x>0.15时超磁致伸缩效应消失;x<0.15时磁致伸缩在低场下(H≤4kA/m)有小幅增加,高场下迅速减小,而且易趋于饱和,说明添加少量Al有助于减小磁晶各向异性.内禀磁致伸缩λ111随Al替代量x的增加大幅度降低.对于0≤x<0.15,穆斯堡尔效应表明,随Al含量的增加Tb0.3Dy0.7(Fe1-xAlx)1.95合金中发生了自旋重取向,易磁化方向经历了[111]→[u v 0]→[u v w]的转变.由相对磁化率随温度的变化关系可以看出,Al替代Fe使自旋重取向温度降低.当x=0.15时,Tb0.3Dy0.7(Fe1-xAlx)1.95合金中出现了少量非磁性相;x>0.15时,合金在室温下呈现顺磁性.     

Tb0.3Dy0.7(Fe1-xAlx)1.95合金的磁致伸缩、自旋重取向和穆斯堡尔谱研究

系统研究了室温下Tb0.3Dy0.7(Fe1-xAlx)1.95(x=0,0.05,0.1,0.15,0.2,0.25,0.3,0.35)合金中金属Al替代Fe对晶体结构、磁致伸缩、各向异性和自旋重取向的影响.结果发现,x<0.4时,Tb0.3Dy0.7(Fe1-xAlx)1.95完全保持MgCl2立方Laves相结构,晶格常量a随Al含量x的增加而增大.磁致伸缩测量发现,随着替代量x的增多磁致伸缩减小,x>0.15时超磁致伸缩效应消失 x<0.15时磁致伸缩在低场下(H≤4kAm)有小幅增加,高场下迅速减小,而且易趋于饱和,说明添加少量Al有助于减小磁晶各向异性.内禀磁致伸缩λ111随Al替代量x的增加大幅度降低.对于0≤x<0.15,穆斯堡尔效应表明,随Al含量的增加Tb0.3Dy0.7(Fe1-xAlx)1.95合金中发生了自旋重取向,易磁化方向经历了[111]→[uv0]→[uvw]的转变.由相对磁化率随温度的变化关系可以看出,Al替代Fe使自旋重取向温度降低.当x=0.15时,Tb0.3Dy0.7(Fe1-xAlx)1.95合金中出现了少量非磁性相 x>0.15时,合金在室温下呈现顺磁性 关键词： 磁致伸缩 立方Laves相 自旋重取向 各向异性 穆斯堡尔谱     

电弧炉制备的Sm2Fe17-χCrχ化合物的结构与磁性

通过X射线衍射、磁测量等手段对电弧炉制备的不同热处理条件的Sm2Fe17-χCrχ(χ=1-3)化合物的结构和磁性进行了研究.结果表明1050℃下退火5 d的Sm2Fe17-χCrχ(χ=1-3)化合物具有菱方相的Th2Zn17型结构,同样温度下退火7 d的Sm2Fe17-χCrχ(χ=2.5,3.0)化合物具有单斜晶系的Nd3(Fe,Ti)2型结构.分析表明与重稀土元素的E2Fe17-χCrχ化合物不同,较长的退火时间以及高含量的Cr可以使得Sm-Fe-Cr化合物的3:29相更加稳定.对晶胞体积及晶胞参数的分析结果表明在Sm2Fe17-χCrχ化合物中存在着较强的各向异性的磁体积效应.磁测量研究结果表明在Th2Ni17型结构及Th2Zn17型结构中,Cr对哑铃晶位上的Fe原子的替代无论是对居里温度还是对磁晶各向异性的影响都是不同的,在Th2Ni17型结构中的影响比较大,在Th2Ni17型结构中的影响比较小.     

Tb0.3Dy0.7Fe2合金的本构参数辨识方法研究

建立了一种简便的、适用于磁畴模型应用的Tb0.3Dy0.7Fe2合金本构参数辨识方法.针对Tb0.3Dy0.7Fe2合金磁畴模型中本构参数不明确且直接实验测试困难的问题,提出了一种数值计算与实验测试相结合的参数辨识方法.采用坐标变换与绘制自由能等势曲线相结合的方法,简化了载荷作用下Tb0.3Dy0.7Fe2合金内磁畴角度偏转的数值计算,研究了合金磁畴角度偏转模型的参数依赖性.在此基础上,结合简单的实验测试,建立了Tb0.3Dy0.7Fe2合金各向异性常数K1和K2、能量分布因子ω、晶轴取向分布的辨识及修正方法.该方法能够简单、快速地完成Tb0.3Dy0.7Fe2合金磁畴模型中本构参数的辨识,对完善磁致伸缩材料磁畴偏转的数值计算模型非常有意义.理论分析可为类磁致伸缩材料磁机耦合模型的建立、完善,以及材料本构参数的辨识、获取提供参考.     

ASE Noise-Reduced Optical Receiver Based on MZI Diversity Scheme

A novel method is proposed that reduces the bit error rate (BER) in an optically amplified system by using a Mach–Zender interferometer coherence manipulation at the receiver. Exact analysis is presented, which shows that the signal-to-noise ratio can be improved by 3 dB. Resulting BER improvements are presented.     

Design of adaptive spatial filter at uniform standard for automatic analysis of digital holographic microscopy

The spatial filtering method is a useful technique for the dynamic and automatic analysis in digital holographic microscopy. It has been shown that the proper selection of the spatial filter would improve the quality of the reconstructed image. However different results would be obtained by employing the spatial filter with different parameter threshold decided at different standard. This paper, according to the histogram analysis of the distribution of the +1 term spectrum of each hologram, gropes for the uniform standard for the decision of the threshold of the adaptive filter. It helps the adaptive spatial filtering method to be more advantageous for the dynamic and automatic analysis.     

Er0.1La0.9P5O14非晶的双光子上转换发光

本文研究了全浓度ＥｒＬａＰ５Ｏ１４非晶在波长λ为６４９．０ｎｍ脉冲染料激光激发下的上转换发光现象，并对其进行了简要的分析。     

Effects of Montmorillonite on the Nonisothermal Crystallization Behavior of the Poly(trimethylene terephthalate)/Polypropylene/Montmorillonite Nanocomposites

Organic montmorillonite (MMT) reinforced poly(trimethylene terephthalate) (PTT)/ polypropylene (PP) nanocomposites were prepared by melt blending. The effects of MMT on the nonisothermal crystallization of the matrix polymers were investigated using differential scanning colorimetry (DSC) and analyzed by the Avrami equation. The DSC results indicated that the effects of MMT on the crystallization processes of the two polymers exhibited great disparity. The PTT's crystallization was accelerated significantly by MMT no matter whether PTT was the continuous phase or not, but the thermal nucleation mode and three-dimensional growth mechanism remained unchanged. However, in the presence of MMT, the PP's crystallization was slightly retarded with PP as the dispersed phase, and was influenced little with PTT as the dispersed phase. When the MMT content was increased from 2_wt% to 7_wt%, the crystallization of the PTT phase was slightly accelerated, whereas the crystallization of the PP phase was severely retarded, especially at lower temperatures. Moreover, the nucleation mechanism for the PP's crystallization changed from a thermal mode to an athermal one. In the polypropylene-graft-maleic anhydride (PP-g-MAH) compatibilized PTT/PP blends, with the addition of 2_wt% MMT during melt blending, the T _c (PTT) shifted 7.8°C to lower temperature and had a broadened exotherm, whereas the T _c (PP) shifted 17.1°C to higher temperature, with a narrowed exotherm. TEM analysis confirmed that part of the PP-g-MAH was combined with MMT during blending.     

卟啉铜接枝SiO2有机-无机复合材料及强的非线性折射率

通过卟啉配合物Meso-四(4-羧基苯基)卟啉铜(简称Cu(Ⅱ)-TCPP)中的羧基与γ-氨基丙基三乙氧基硅烷(NH₂(CH₂)₃Si(OC₂H₅)₃,KH550)中的氨基的相互化学作用,成功地把卟啉配合物接枝到KH550中,随着KH550中乙氧基的水解与聚合反应的进行,卟啉铜连接到固体介质中,从而大幅度提高了卟啉在无机固体介质中的掺杂浓度. 将反应产物与γ-(2,3-环氧丙氧基)丙基三甲氧基硅烷(CH₂CHCH₂O(CH₂)₃Si(OCH₃)₃,KH560) 相杂化,形成物化性能良好、连接卟啉的有机-无机复合材料. 用红外光谱表征了Cu(Ⅱ)-TCPP与KH550的化学反应产物,用紫外—可见吸收光谱研究Cu(Ⅱ)-TCPP的分子状态. 应用Z扫描技术研究不同Cu(Ⅱ)-TCPP掺杂浓度的复合材料的非线性光学性质,其三介非线性折射率n₂达-1.1161×10^-16 m²/W. 关键词： 非线性折射率 有机-无机复合材料 接枝 Meso-四(4-羧基苯基)卟啉铜     

Phase-matched third-harmonic UV generation using low-order modes in a glass micro-fiber

We observe phase-matched third-harmonic generation at 355 nm in a low-order mode of a sub-micron diameter glass fiber. The third-harmonic signal exhibits a sharp resonance for a fiber diameter d = 0.49 ± 0.02 μm, in excellent agreement with the value d = 0.506 μm predicted by theory. The third-harmonic conversion efficiency is 2 × 10⁻⁶, and is limited by the pump power (1 kW) and effective fiber length (100 μm).     

(ZnSe)n(n=1,2)团簇结构及ZnSe分子热力学性质的理论计算

用密度泛函B3LYP方法、6-311 G基组对(ZnSe)n(n=1,2)分子体系进行了理论研究,得到(ZnSe)n(n=1,2)分子体系的基态电子状态的平衡几何Re、谐振频率、偶极矩和离解能De及不同温度、压力下的热力学函数值;设用总能量中的电子和振动能量近似代表ZnSe分子处于固态时的能量,用总熵中的电子和振动熵近似代表ZnSe分子处于固态时的熵,进而计算了Zn与Se反应的ΔH0、ΔS0、ΔG0,并由此计算出不同温度的反应平衡常数Kp.结果表明:在298~1150 K温度范围内,Zn与Se反应的自由能值均为负,且随着温度的升高,ΔG0值负的越多,表明在这个温度范围内反应能自发发生,而且自发趋势随温度的升高逐渐增大;平衡常数逐渐减小,即反应进行程度随温度的升高逐渐减小;ZnSe分子材料的导电性随压力增大而增强.     

Imprinting the nanostructures on the high refractive index semiconductor glass

The centimeter range one- and two-dimensional nanostructures of 70 nm pitch have been imprinted by hot pressing with a quartz, silicon or nickel mold, at 240 °C, onto the surface of Ge₂₀As₂₀Se₁₄Te₄₆ semiconductor glass. Excellent glass stability of this glass allows multiple re-pressing of the nano-structures. With increasing the Te/Se ratio in the glass formula, the refractive index reaches a value of 3.5 with an option of free electron absorption at elevated temperatures pointing out the use of such nanostructures in submicron and micron scale electronic devices/chips, moth eye structures and photonic crystals.     

Tip-surface interactions at redox responsive poly(ferrocenylsilane) (PFS) interface by AFM-based force spectroscopy

Poly(ferrocenylsilanes) (PFS) belong to the class of redox responsive organometallic polymers. Atomic force microscopy (AFM)-based single molecule force spectroscopy (SMFS) was used earlier to study single chain PFS response and redox energy driven single chain PFS molecular motors. Here we present further AFM investigations of force interactions between tip and a grafted PFS surface under potential control in electrochemical redox cycles. Typical tip-Au interaction is considered as reference in the force measurements. First the electrostatic component in the diffused double layer (DL) in NaClO₄ electrolyte environment was considered for a “grafted to” PFS, which dominated the interplay between the tip and sample surface. The DL forces can also hinder the physisorption of PFS chain onto the tip when the voltage was applied at −0.1 V. On the other hand, if the tip contacted the PFS surface prior to the electrochemical process, physisorption of PFS chains governed the overall interaction regardless of subsequently applied surface potential. In addition, prolonged contact time, t_c, may also contribute to the stability of tip-PFS bridging and detection of electrostatic forces between the tip-PFS interface. The results showed that tip-substrate interaction forces without PFS grafts have negligibly small force contributions under similar, electrochemically controlled, conditions used in single PFS chain based molecular motors.