Processing of duplex stainless steel by WEDM

This study investigates the manufacturing process of 2205 duplex stainless steel by wire electrical discharge machining where the effects of pulse-on time (PONT), wire tension and pulse-off time (POFT) on surface finish, kerf width, and material removal rate (MRR). It was found that the kerf width was unchanged with the change of PONT at long pulse-of time and higher wire tension. However, it decreased initially and then increased due to the rise of PONT at low values of wire tension and POFT. Low wire tension and PONT, POFT and contributed towards widest kerf. Longer PONT increased MRR due to higher machining/processing speed. Lower wire tension and shorter POFT increased MRR more than that of higher wire tension and POFT. Craters and recast layer were on the machined surfaces at all machining conditions. Increased PONT raised surface roughness at the lower POFT and tension in the wire. The surface finish at high wire tension and longer PONT is always better than that at smaller PONT and lower tension in the wire. The microstructure underneath the recast layer remains unchanged and the failure of wire electrode occurred at higher wire tension, longer PONT and shorter POFT.     

Wire EDM Mechanism of MMCs with the Variation of Reinforced Particle Size

The size of reinforced particles notably affects the electro-discharge machining (EDM) of metal matrix composites (MMCs). This paper explores the mechanism of wire EDM of MMCs with different sizes of reinforced particles as well as the corresponding unreinforced matrix material. The mechanisms of material removal, surface generation, and taper kerf formation were investigated. This study shows that the particles’ ability to protect matrix materials from the intense heat of electric arc controls the material removal rate, surface generation, and taper of kerf. The low melting point matrix material is removed very easily, but the heat resistance reinforced particles delay the removal of material and facilitate the transfer of the workpiece material to wire electrode and vice versa. Thus, the material stays longer in touch with intense heat and affects the surface generation, wire electrode wear, and width of the kerf.     

Influence of materials and machining parameters on WEDM of Al/AlCoCrFeNiMo0.5 MMC

The current study intends to optimize the wire electric discharge machining (WEDM) parameters while machining the newer AlCoCrFeNiMo_0.5 high entropy alloy (HEA) particles-reinforced aluminum composites. AlCoCrFeNiMo_0.5 HEA particles produced through arc melting technique are reinforced here for different weight % (0%, 3%, 6%, 9%, 12%, and 15%) along with pure aluminum by the way of powder metallurgy. WEDM studies were conducted by varying the appropriate parameters, namely, pulse ON time, pulse OFF time, and wire feed. Based on the selected parameters, through Taguchi method L18 orthogonal array is designed; the optimal parameter combination for better surface finish, material removal rate (MRR), and reduced kerf width (KW) is identified. For better understanding, through ANOVA, also the effect of each input variables over these adopted response variables was analyzed. The yielded results reveal that addition of AlCoCrFeNiMo_0.5 HEA as reinforcement has considerable effect over the response variablessuch that MRR and KW reduces; surface roughness increases with increase in HEA %. ANOVA results confirm that pulse ON time has higher effect over the response variables than any other parameters involved for the study. Multi-objective optimization done through Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) methodology answers that MRR and surface finish have improved, whereas KW gets reduced noticeably.     

Electrical Discharge Machining of Functionally Graded 15-35 Vol% SiCp/Al Composites

A functionally Graded 15-35 volume% silicon carbide particulate (SiC_p) reinforced Al359 metal matrix composite (SiC_p/Al MMC) was drilled by electrical discharge machining (EDM) to assess the machinability and workpiece quality. The machining conditions were identified for both the machining performance and workpiece quality of the EDM process, including some aspects of material removal mechanisms, material removal rate (MRR), electrode tool wear, and subsequent drilled hole quality including surface texture and roundness by using surface profilometry, coordinate measuring machine (CMM), and scanning electron microscopy (SEM). It was observed that the material removal rate increases with increasing peak current and pulse-on-time up to the optimal points and drops drastically thereafter. Higher peak current and/or pulse-on-time result in both the greater tool wear and the larger average diameter error. As the percentage of the SiC particles increases, MRR was increased and electrode wear was found to be decreased. At the EDM machined subsurface layer, the fragmented and melted SiC particles were observed under the SEM and EDX-ray examination.     

Effects of electrode materials on performance measures of electrical discharge micro-machining

The main objective of this study is to investigate the effects of various electrode materials and their influences on electrical discharge micro-machining performance attributes. The performance attributes are determined in terms of tool wear rate (TWR), material removal rate (MRR), taper angle, overcut, and surface roughness by drilling micro-holes on SS 316?L material. It is noticed that, for high discharge energy the MRR, TWR, taper angle, and overcut are more and also when the thermal conductivity, boiling point, and melting point of the electrode material are high, the TWR is low. The surface finish is good at low discharge energy and low spindle speed. If the tool electrode is rotating at minimum speed during machining, a centrifugal effect is created on the dielectric so that debris at the inter-electrode gap is evacuated efficiently. If the tool is stationary, then the machining conditions are unstable due to improper flushing of debris.     

WEDM of layered composite: analyzing material removal and cut quality issues

The use of cladded bimaterial composites has grown in the recent past as they offer a combination of properties at low cost. But the heterogeneity which is the inherent attribute of these composites makes it challenging to accurately cut via conventional means. Therefore, thermal cutting is commonly employed for their cutting which not only produce poor cut quality and deeper heat affected zones but also demand subsequent finishing operations. Wire electric discharge cutting (WEDM) is a proficient alternate but low material removal (MRR) and widen kerf slot (KW) due to sideways sparking limit its application. Moreover, both layers of material have different thermoelectric properties and are subjected to simultaneous cutting by a single moving wire electrode which lead to produce different spark strength against both layers. In this regard, the present study aims to investigate the cutting potential of WEDM for cladded bimaterial with a prior focus on both the aforesaid issues, i.e. MRR and KW. Considering the thermoelectric nature of the WEDM, workpiece-related parameters like orientation of work surface and layer thickness of each layer are taken as control variables in addition to the WEDM process parameters. Experimental results are thoroughly analyzed using statistical and SEM analysis.     

Machinability of Nickel-Based Superalloy by Abrasive Water Jet Machining

This paper deals with the machinability of nickel-based superalloys using abrasive water jet machining process. The machining studies were carried out with three different parameters such as water jet pressure, traverse speed of jet nozzle, and standoff distance at three different levels. The performances of the process parameters are evaluated by measuring difference in kerf width, kerf wall inclination, and material removal rate (MRR). Further, the surface morphology and material removal mechanisms are analyzed through scanning electron microscope (SEM) images. It is found that water jet pressure is the most influencing factor related to surface morphology and surface quality.     

Experimental investigation on low-frequency vibration-assisted µ-ED milling of Inconel 718

The microelectric discharge (µ-ED) milling is a competent process for the fabrication of complex 3-D shapes, but longer machining time limits the wide applications of the process. Therefore, in this work, a novel approach of low-frequency workpiece vibration-assisted µ-ED milling has used intending to improve the process performance. The experimental investigation has been performed using Taguchi L-16 orthogonal array to examine the effects of low-frequency workpiece vibration assistance in the µ-ED milling while fabricating microchannels on Inconel 718. The gap voltage, capacitance, and vibration frequency were selected as input parameters while material removal rate (MRR) and frontal electrode wear (FEW) were chosen as response variables. It has been observed that the MRR increases and FEW decreases with an increase in vibrational frequency up to an optimal value and then decreases for further increase in vibration frequency. The results disclose a positive influence of the low-frequency workpiece vibration of both MRR and FEW during µ-ED milling of Inconel 718. Finally, the effects of vibration and discharge energy on surface quality of fabricated microchannels were analyzed using field emission scanning electron microscopic images.     

Experimental Investigations of Abrasive Mixed Electro Discharge Diamond Grinding of Nimonic 80A

This paper presents a novel hybrid machining process (HMP) called abrasive mixed electro discharge diamond grinding (AMEDDG) in which abrasive powder is mixed in dielectric fluid to perform electro discharge diamond grinding (EDDG) action on a workpiece. In-house-fabricated AMEDDG setup was used to experimentally evaluate the performance of the process during the machining of Nimonic 80A. The effects of wheel speed, powder concentration, current, and pulse-on-time (POT) were investigated on the material removal rate (MRR). The surface morphological properties of the machined workpiece were investigated based on some quality surface indicators. The experimental results show that MRR of the workpiece was influenced by wheel speed, current, and powder concentration, and optimum MRR can be achieved at a wheel speed of 1400 RPM, a powder concentration of 4 g/L, a current of 10 A, and a POT of 26 µs.     

An investigation on cutting quality by adding polymer in abrasive water jet

ABSTRACT

An experimental investigation is presented to improve the cutting quality in abrasive water jet (AWJ) cutting of marble by an addition of polyacrylamide (PAM). Considering experimental data, the kerf widths have a remarkable change when the PAM concentration approaches to 400 ppm. The deviation between top and bottom kerf width reaches the minimal value when PAM concentration is equal to about 600 ppm. In addition, the surface topography analyses illustrate that an addition of PAM can broaden the cutting wear zone and make the cutting quality better. Furthermore, the effects of PAM on the surface roughness are assessed by a profilometer. It is eventually found that the surface roughness decreases initially and then increases greatly with the increase of the depth of cut. Additionally, the minimum surface roughness occurs when the PAM concentration is 600 ppm, which agrees well with the experimental result of kerf width. An increasing stand-off distance or traverse speed produces a higher surface roughness.     

Performance of Additive Mixed Kerosene–Servotherm in Electrical Discharge Machining of Monel 400™

In general, kerosene and commercial grade EDM oils are conventional dielectric fluids in electrical discharge machining (EDM), despite their poor performance measures being major drawbacks. The aim of this study was to develop a dielectric fluid offering good performance measures in the EDM process, by determining the appropriate proportion of kerosene–servotherm and analyzing its performance with and without the additive concentration in EDM of monel 400?. Sixteen samples of kerosene–servotherm of varying proportions were used in this study. The optimum proportion of kerosene–servotherm was found to be 75:25, which resulted in the highest material removal rate (MRR) as compared with tool wear rate (TWR), and surface finish was found to be poorer than when using kerosene alone. In addition, 1 l of kerosene–servotherm concentrated with 6 g of graphite powder (one micron) exhibited substantial improvement in MRR, surface finish, and TWR compared with conventional dielectric fluids. Therefore kerosene–servotherm (75:25) concentrated with 6 g/l of graphite powder can be accepted as a potential dielectric fluid offering high MRR along with enhanced surface finish in EDM.     

Examinations concerning the electric discharge machining of AZ91/5B4CP composites utilizing distinctive electrode materials

In this study, investigation has been conducted in the focus of obtaining better surface finish in the electro discharge machining (EDM) of AZ91/5B₄C_p magnesium composites using distinctive sort of anode viz. copper, tungsten–copper, brass, aluminum and 20Gr/AA6061 (GRAL-20) composites. The process parameters, pulse on time and current were performed to research the machining qualities through material removal rate (MRR) and tool wear rate (TWR). The machined composites were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The formation of black spots was observed on machining with copper–tungsten and these black spots were not found when GRAL-20 was used as electrode. Machined with GRAL-20 electrode leads to the increase in spark gap, hence adequate flushing occurs; it eliminates re-melted layers on machined surface results in better surface roughness value. The results revealed that GRAL-20 electrodes posses better MRR followed by copper electrode whereas tungsten–copper exhibits better TWR followed by GRAL-20 electrode.     

Experimental Investigations into the Effects of Microelectric-Discharge Milling Process Parameters on Processing Ti–6Al–4V

Microelectric-discharge milling is acquiring more importance in micromanufacturing because of its unique ability to produce three-dimensional microcavities with high aspect ratio in electrically conductive advanced materials regardless of its mechanical properties. The present study investigates the effects of major microelectric-discharge milling process variables [voltage (V), capacitance (C), electrode rotational speed (ERS), and feed rate (FR)] on Ti–6Al–4V. The output performance measures were identified as material removal rate (MRR) and tool wear rate (TWR) to assess the machinability of Ti–6Al–4V. Experiments were designed and carried out based on response surface methodology-Box-Behnken statistical design. The most influencing parameters for responses (MRR, TWR) were found to be capacitance and FR. At a capacitance of 0.4 µF and FR of 18 mm/min, maximum MRR of 0.9756 mg/h, and TWR of 0.6342 mg/h were observed. Similarly at 0.01 µF and 6 mm/min, minimum MRR of 0.2308 mg/h, and TWR of 0.1259 mg/h were obtained.     

Wire electrical discharge machining characteristics of AA6061/cenosphere as-cast aluminum matrix composites

Machining of metal matrix composites (MMCs) reinforced with low-density waste byproduct particulates using nonconventional processes is relatively new in the field of material science. However, more attention has been paid for investigations on nontraditional machining of such MMCs currently as the conventional machining may generate additional complexity. This study investigates the wire electro-discharge machining behavior of compo-casted cenosphere-reinforced AA6061 alloys. Cu₆₀Zn₄₀-coated copper wire was used as electrode material. The investigation demonstrates that melting and vaporization are the dominant machining mechanisms. The weight fraction of cenosphere was observed to be the most substantial process variables affecting the cutting rate, on-time, and the wire speed of tool were the next in the order of importance. The presence of nonconductive cenosphere particles along with thermal degradation of the aluminum matrix composites leads to degrading processed machined surface quality. The issues related to wire breakage and poor quality of the machined surface, surface finish, and dimensional accuracy are described in detail.     

Multi‐response optimization of the machining characteristics in electrical discharge machining (EDM) using span‐20 surfactant and chromium (Cr) powder mixed

Effects of Chromium (Cr) powder concentrations (C_p) and Span‐20 surfactant concentrations (C_s) on AISI D2 hardened steel were evaluated using response surface methodology (RSM) and parameter processing parameter were optimized for optimal parameter conditions using multi‐response desirability function. Responses taken involved material removal rate (MRR), electrode wear rate (EWR) and surface roughness (R_a). The experimental plan was based on the face centered, central composite design (CCD) using version 10.0 of the Design Expert software. The results identified that C_p is the most important parameter to maximize material removal rate (MRR) and minimize electrode wear rate (EWR) and surface roughness (R_a). With the topmost desirability solution, the suggested optimum parameter condition of C_p and C_s were 2.155 g/L and 10.000 g/L, respectively.     

Investigations on surface quality of WEDM-manufactured meso bevel and helical gears

This article presents investigations on and analysis of surface finish of meso bevel and helical gears made of stainless steel (SS 304) manufactured by wire electric discharge machining (WEDM) process using thin soft plain brass wire of 0.25?mm diameter. Effects of eight WEDM process parameters, namely, peak current, pulse-on time, pulse-off time, wire feed rate, wire tension, servo-gap voltage, dielectric pressure, and cutting speed on average and maximum surface roughness of the meso bevel and helical gears have been studied by conducting 31 experiments using one-factor-at-a-time approach to identify their optimum ranges/values for further experiments. Tooth profile, microstructure, microhardness, and topography of tooth flank surface have been studied for the best quality meso gears. Average and maximum surface roughness of tooth flank surfaces of meso bevel and helical gears increase with increase in peak current, servo-gap voltage, pulse-on time, wire feed rate, wire tension and cutting speed, and decrease with increase in pulse-off time while dielectric pressure does not significantly influence surface roughness. This work establishes that WEDM process can be an economic and sustainable manufacturing alternative for net-shaped meso-sized bevel and helical gears having better surface finish which will eliminate need of any subsequent finishing processes.     

Ti-Al双丝超音速电弧喷涂涂层的滑动磨损特性研究

为了提高铝合金(LY12)的表面耐磨性,采用钛、铝金属丝材和SAS-Ⅰ型超音速电弧喷涂设备,利用二次回归正交试验方法、有润滑滑动磨损试验、涂层显微组织和磨损表面形貌观察、XRD分析,定量分析了喷涂电压和喷涂距离对涂层滑动磨损体积的影响规律,并进行了喷涂工艺参数的优化及其与基体滑动磨损的对比试验.结果表明:在特定的磨损和喷涂条件下,当喷涂距离较小时,随喷涂电压的增大,涂层的体积磨损量逐渐减小;随着喷涂距离的增加,涂层的体积磨损量随喷涂电压的升高逐渐增大,并且喷涂距离越大,涂层的体积磨损量随喷涂电压增大的速率愈大.当喷涂电压比较低时,涂层的体积磨损量随喷涂距离的增大而降低,但是,随喷涂电压的逐渐升高,涂层的体积磨损量随喷涂距离的增大逐渐上升,并且,喷涂电压愈高,其随喷涂距离而增加的速率越快.当喷涂电压和喷涂距离分别为26V和0 236m时,涂层具有最佳的耐滑动磨损性能,根据该工艺参数制成的涂层,其滑动磨损体积仅为LY12铝合金的1/38.84.即在适当的工艺条件下,Ti-Al双丝超音速电弧喷涂涂层对LY12铝合金具有显著的表面耐磨强化作用.     

Parametric Evaluation on Near-Dry Electric Discharge Machining

Near-dry electric discharge machining (EDM) is an eco-friendly process. It does not produce toxic fumes and consequent health hazards. The near-dry EDM generally utilizes a mixture of two phase (liquid and air) dielectric for machining. This investigation reports the influence of four processing parameters, viz. current, flushing pressure, duty factor, and lift on three responses. The responses measured were material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The work material chosen was high speed steel (HSS). Mathematical models have been proposed herein for evaluation of the effect of processing parameters in near-dry EDM. These models were developed using response surface methodology (RSM). The experimental results reveal that the process parameters taken into consideration were significant for MRR. The TWR was negligible in near-dry EDM. This process gives a finer surface finish with thinner recast layer even at higher discharge energies as compared to conventional EDM.     

Investigation into the Effect of Voltage Excitation of Pre-Ignition Spark Pulse on the Electro-Discharge Machining (EDM) Process

Studying the variation of the electro-discharge machining (EDM) process outputs due to the change in shape of the generated pulse is one research aspect in the EDM process. In this study, the effects of voltage excitation of the pre-ignition spark pulse on the process outputs material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (Ra) have been investigated. Experiments were designed using design of experiments (DOE), and the results were analyzed using analysis of variance (ANOVA). Based on the results, it has become clear that applying voltage excitation of the pulse produces effective pulses, which in turn lessens EWR, increases MRR, and improves surface quality. Hence, the suitability of this method has been verified for EDM.     

Fiber laser cutting of CFRP composites and process optimization through response surface methodology

In this experimental study, the effects of major laser process control parameters, such as the laser power, beam scanning speed and assisting gas flow rate, on cut surface integrity defined by the kerf width, taper percentage, and the extent of heat affected zone (HAZ) were investigated. Response surface methodology (RSM) along with central composite design (CCD) of the experiment was used to optimize the process parameters to get better-cut surface quality. The optimum values of process parameters corresponding to cut surface with minimum defects are laser power 260?W, cutting speed 4500?mm per min, and assistance gas flow rate 14.23?l/min and the corresponding kerf width, taper percentage, and the width of HAZ are found to be 163.7?µm, 5.75%, and 573.28?µm. The confirmation experiments have been conducted that provide favorable results with an error of 2.70%, 1.87%, and 0.36%, for kerf width, taper percentage, and width of HAZ, respectively.