共查询到19条相似文献,搜索用时 500 毫秒
1.
乙炔动火分析,严格控制动火允许指标,取样要有代表性,选择适宜的分析方法,熟练掌握分析技术,使分析结果准确可靠,严格执行《安全生产动火制度》,确保做好安全动火作业,保证企业生产安全稳定的运行。 相似文献
2.
在进入容器内部进行检修时,容器应与系统完全隔绝,并经清洗、置换,再对其内部的气体进行安全分析。分析项目有可燃气体、氧及有毒气体含量的分析。1.可燃气体含量的安全评价进入容器动火的标准要根据可燃介质的爆炸下限来确定。对于单一的可燃气体(或可燃液体的蒸汽,下同),动火分析标准如 相似文献
3.
常温下,氯乙烯为有毒、有害、可燃性气体,与空气混合后极易发生爆炸。因此,其动火分析的准确程度,直接关系到操作人员的人身安全和国家财产。氯乙烯的动火分析,以往通常使用测爆仪,由于氯乙烯具有一定的腐蚀性,所以在分析时对测爆仪中铂丝的活性有一定的影响,使用几次后,铂丝就会中毒,使仪器的灵敏度降低,进而影响分析结果的准确度。 相似文献
4.
针对目前氯化苄生产及使用单位对其动火分析没有形成统一标准的现状,作者结合自己多年的探索经验,摸索出采用气相色谱仪对微量氯化苄动火分析的方法。认为当氯化苄浓度低于0.01%时,可视为绝对安全浓度,可以满足动火要求。 相似文献
5.
6.
详细描述了动火分析中用氢火焰气相色谱法测定空气中可燃气体含量的分析方法,利用该方法测定可燃气体含量。证明该测定方法灵敏度高、快速方便、简单易行,非常适用于动火分析。 相似文献
7.
本文以奥式气体分析仪测定气体含量为基础,以燃烧法为具体测定方法,对化工企业动火区可燃气体含量的测定进行了探讨。该方法在安全动火分析中准确可靠,快速测定。并且对该方法的注意事项进行了分析。 相似文献
8.
详细介绍了美国Partridge—Raleigh油田发生火灾爆炸事故的经过,对事故调查的发现进行了简要分析,指出作业现场存在动火作业不安全和临时作业平台不合格等问题。针对API和NFPA标准中对动火作业的要求分析了事故发生的原因,详细介绍了动火作业不可缺少的过程,即风险评估、设置动火区域、隔离、气体检测、监火、动火设备、动火作业许可、实施动火、清理现场等。 相似文献
9.
10.
11.
12.
石油化工企业的生产工作,包括对油品进行的加工,都要求油品的质量.因此需要借助一些技术手段,从而全方位的对油品进行检验和分析.传统的油品质量分析法,耗费的时间比较长,检验分析结果也可能存在一定的偏差.因此,现代仪器分析技术得到了有效应用,并取得了一定的成果. 相似文献
13.
尿素生产中常量二氧化碳分析方法探讨 总被引:2,自引:0,他引:2
通过分析探讨影响二氧化碳测定结果的因素,表明在强碱性条件下,甲醛的存在会影响二氧化碳分析结果,应严格控制强碱的加入量和分析时间. 相似文献
14.
碳化物复相陶瓷及高温等静压氮化表面改性 总被引:3,自引:0,他引:3
采用高温等静压氮化表面改性技术制备高性能复相陶瓷。首先实施无包封致密化工艺技术,提出了Reaction-HIP模型从理论上给予解释;成功地制备出Si3N4-SiC梯度功能材料,并推广到一系列碳化物或含碳化物复焙,使我国碳化物复相陶瓷研究和表面改性技术处于国际领先地位。 相似文献
15.
Zhong‐Ming Li Bang‐Hu Xie Rui Huang Xiang‐Ping Fang Ming‐Bo Yang 《Polymer Engineering and Science》2004,44(12):2165-2173
An in‐situ microfibrillar blend based on poly(ethylene terephthalate) (PET) and polyethylene (PE) was fabricated through slit die extrusion, hot stretching, and quenching. The morphological characteristics of the PET phase, such as diameter and its distribution, which were observed after the matrix was etched away, appear to be dependent on the hot stretch ratio at a fixed blend composition. The increase of the hot stretching ratio makes the PET particles change from spheres and ellipsoids to rodlike particles, and finally to well‐defined microfibers. The fracture toughness of the in‐situ microfibrillar blend was evaluated using deeply double‐edge notched tension (DDENT) specimens according to the essential work of fracture procedure. Initially, the increase of hot stretch ratio makes the specific essential work of fracture (we) rise. A maximum we appears at 25.4. Further increase of hot stretch ratio causes a slightdecrease of we. On the other hand, it shows that lower hot stretch ratios make the specific non‐essential work of fracture (wp) rise slightly. As it exceeds 6.4, wp decreases substantially. It was believed that the characteristics of the PET domains were responsible for the fracture behaviors of the in‐situ microfibrillar blend. Polym. Eng. Sci. 44:2165–2173, 2004. © 2004 Society of Plastics Engineers. 相似文献
16.
This work presents modeling and numerical simulation of batch convective coal drying in a deep packed bed after a high-pressure steam treatment (a part of the Fleissner coal drying process). The process is atypical, because ambient air is used to dry and cool hot particles, while usually, e.g., in the deep packed bed drying of biomaterials, hot air is contacting cold particles. Product-specific data (intraparticle mass transfer, gas-solids moisture equilibrium) for coal (here lignite) are taken over from literature. Available data on coal drying in packed beds of medium height are used for model validation. Then, the model is applied to the considered industrial process. The design point of the process is critically reviewed, and alternatives are developed by systematically simulating the influence of inlet air conditions (temperature, humidity, flow-rate) and coal particle size. This type of analysis is necessary for efficiently scheduling plant dryers, since coal particle size may change, and air inlet temperature and humidity are changing with the ambient conditions. 相似文献
17.
18.
针对《锅炉安全技术监察规程》(征求意见稿)中没有热油炉清洗内容的问题,通过对炉型的分析与比较,为了热油炉安全运行,建议恢复相关内容。 相似文献
19.
应用热分析有限元软件模拟输送带蒸气加热热板边界的温度场,进行有限元分折,得出蒸气热板边界温度场分布图,利用MATLAB软件对数据进行拟合处理,得到数据拟合图和相应的拟合公式,为蒸气加热热板边界的温度场研究提供了参考. 相似文献