Lithium-ion battery anode properties of TiO2 nanotubes prepared by the hydrothermal synthesis of mixed (anatase and rutile) particles

From mixed (anatase and rutile) bulk particles, anatase TiO₂ nanotubes are synthesized in this study by an alkaline hydrothermal reaction and a consequent annealing at 300-400 °C. The physical and electrochemical properties of the TiO₂ nanotube are investigated for use as an anode active material for lithium-ion batteries. Upon the first discharge-charge sweep and simultaneous impedance measurements at local potentials, this study shows that interfacial resistance decreases significantly when passing lithium ions through a solid electrolyte interface layer at the lithium insertion/deinsertion plateaus of 1.75/2.0 V, corresponding to the redox potentials of anatase TiO₂ nanotubes. For an anatase TiO₂ nanotube containing minor TiO₂(B) phase obtained after annealing at 300 °C, the high-rate capability can be strongly enhanced by an isotropic dispersion of TiO₂ nanotubes to yield a discharge capacity higher than 150 mAh g⁻¹, even upon 100 cycles of 10 C-rate discharge-charge operations. This is suitable for use as a high-power anode material for lithium-ion batteries.     

Enhanced high rate capability of dual-phase Li4Ti5O12–TiO2 induced by pseudocapacitive effect

The dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite is successfully synthesized by a hydrothermal route with adding thiourea. The electrochemical performance of the dual-phase nanocomposite as anode for lithium-ion batteries is investigated by the galvanostatic method, cyclic voltammetry and electrochemical impedance spectra. It is demonstrated that the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite presents the improved electrochemical performance over individual single phase Li₄Ti₅O₁₂ and anatase TiO₂ samples. After 300 cycles at 1 C, the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite can still maintain the large discharge capacity of 116 mAh g⁻¹. It indicates that the as-prepared nanocomposite can endure great changes of various discharge current densities to retain a good stability. The large discharge capacity of 132 mAh g⁻¹ is also obtained at the large current density of 1600 mA g⁻¹ upon cycling. In particular, as verified by the cyclic voltammetry, the pseudocapacitive effect is induced due to the presence of abundant phase interfaces in the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite, which is beneficial to the enhanced high rate capability and good cycle stability.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Enhanced electrochemical properties of LiFePO4/C synthesized with two kinds of carbon sources,PEG-4000 (organic) and Super p (inorganic)

Olivine structured LiFePO₄/C cathode was synthesized via a freeze-drying route and followed by microwave heating with two kinds of carbon sources: PEG-4000 (organic) and Super p (inorganic). XRD patterns indicate that the as-prepared sample has an olivine structure and carbon modification does not affect the structure of the sample. Image of SEM shows a uniform and optimized particles size, which greatly improves the electrochemical properties. TEM result reveals the amorphous carbon around the surface of the particles. At a low rate of 0.1 C, the LiFePO₄/C sample presents a high discharge capacity of 157.8 mAh g⁻¹ which is near the theoretical capacity (170 mAh g⁻¹), and it still attains to 149.1 mAh g⁻¹ after 200 cycles. It also exhibits an excellent rate capacity with high discharge capacities of 143.2 mAh g⁻¹, 137.5 mAh g⁻¹, 123.7 mAh g⁻¹ and 101.6 mAh g⁻¹ at 0.5 C, 1.0 C, 2.0 C and 5.0 C, respectively. EIS results indicate that the charge transfer resistance of LiFePO₄ decreases greatly after carbon coating.     

Synthesis and electrochemical studies of a layered spheric TiO2 through low temperature solvothermal method

This paper demonstrates a low temperature solvothermal method for the synthesis of a layered spheric TiO₂. The crystal structure and morphology of the material were characterized by using X-ray diffraction (XRD) and scanning electron miscopy (SEM). Electrochemical performances of the TiO₂ when used as anode material in lithium ion batteries were investigated by galvanostatic charge/discharge and cyclic voltammetry experiments. A discharge capacity of 179 mAh g⁻¹ was obtained in the potential range between 3.0 and 1.5 V. No significant capacity decay was observed in the successive 30 cycles showing satisfactory cycling performance of the electrode.     

TiO2 nanotube arrays annealed in CO exhibiting high performance for lithium ion intercalation

Anatase titania nanotube arrays were fabricated by means of anodization of Ti foil and annealed at 400 °C in respective CO and N₂ gases for 3 h. Electrochemical impendence spectroscopy study showed that CO annealed arrays possessed a noticeably lower charge-transfer resistance as compared with arrays annealed in N₂ gas under otherwise the same conditions. TiO₂ nanotube arrays annealed in CO possessed much improved lithium ion intercalation capacity and rate capability than N₂ annealed samples. At a high charge/discharge current density of 320 mA g⁻¹, the initial discharge capacity in CO annealed arrays was found to be as high as 223 mAh g⁻¹, 30% higher than N₂ annealed arrays, ∼164 mAh g⁻¹. After 50 charge/discharge cycles, the discharge capacity in CO annealed arrays remained at ∼179 mAh g⁻¹. The improved intercalation capacity and rate capability could be attributed to the presence of surface defects like Ti-C species and Ti³⁺ groups with oxygen vacancies, which not only improved the charge-transfer conductivity of the arrays but also possibly promoted phase transition.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Nanostructured Si/TiC composite anode for Li-ion batteries

Si/TiC nanocomposite anode was synthesized by a surface sol-gel method in combination with a following heat-treatment process. Through this process, nanosized Si was homogeneously distributed in a titanium carbide matrix. The electrochemically less active TiC working as a buffer matrix successfully prevented Si from cracking/crumbling during the charging/discharging process. The interspaces in the Si/TiC nanocomposite could offer convenient channels for Li ions to react with active Si. The Si/TiC composite exhibited a reversible charge/discharge capacity of about 1000 mAh g⁻¹ with average discharge capacity fading of 1.8 mAh g⁻¹ (0.18%) from 2nd to 100th cycle, indicating its excellent cyclability when used as anode materials for lithium-ion batteries.     

Anatase TiO2 spheres with high surface area and mesoporous structure via a hydrothermal process for dye-sensitized solar cells

Spherical pure anatase TiO₂ spheres with a mesoporous structure and high surface area of up to 116.5 m² g⁻¹ were prepared by a simple urea-assisted hydrothermal process and investigated as dye-sensitized solar-cell electrodes. Although the particle diameters of the prepared TiO₂ spheres ranged from 0.4 to 1.3 μm, due to the high specific surface area, mesoporous TiO₂ sphere electrode was obtained with enhanced light harvesting and a larger amount of dye loading. An overall light conversion efficiency of 7.54% under illumination of simulated AM 1.5G solar light (100 mW cm⁻²) was achieved using the mesoporous TiO₂ spheres electrode, which was significantly higher than a commercial Degussa P25 TiO₂ nanocrystals electrode (5.69%).     

Performance evaluation of printed LiCoO2 cathodes with PVDF-HFP gel electrolyte for lithium ion microbatteries

In order to improve the discharge capacity in lithium ion microbatteries, a thick-film cathode was fabricated by a screen printing using LiCoO₂ pastes. The printed cathode showed a different discharge curves when the cell was tested using various (liquid, gel and solid-state) electrolytes. When a cell test was performed with organic liquid electrolyte, the maximum discharge capacity was 200 μAh cm⁻², which corresponded to approximately 133 mAh g⁻¹ when the loading weight of LiCoO₂ was calculated. An all-solid-state microbattery could be assembled using sputtered LiPON electrolyte, an evaporated Li anode, and printed LiCoO₂ cathode films without delamination or electrical problems. However, the highest discharge capacity showed a very small value (7 μAh cm⁻²). This problem could be improved using a poly(vinylidene fluoride-hexafluoro propylene) (PVDF-HFP) gel electrolyte, which enhanced the contact area and adhesion force between cathode and electrolyte. The discharge value of this cell was measured as approximately 164 μAh cm⁻² (≈110 mAh g⁻¹). As the PVDF-HFP electrolyte had a relatively soft contact property with higher ionic conductance, the cell performance was improved. In addition, the cell can be fabricated in a leakage-free process, which can resolve many safety problems. According to these results, there is a significant possibility that a film prepared using the aforementioned paste with screen printing and PVDF-HFP gel electrolyte is feasible for a microbattery.     

A novel micro-spherical CoSn2/Sn alloy composite as high capacity anode materials for Li-ion rechargeable batteries

Micro-scaled spherical CoSn₂/Sn alloy powders synthesized from oxides of Sn and Co via carbothermal reduction at 800 °C were examined for use as anode materials in Li-ion battery. The phase composition and particle morphology of the CoSn₂/Sn alloy composite powders were investigated by XRD, SEM and TEM. The prepared CoSn₂/Sn alloy composite electrode exhibits a low initial irreversible capacity of ca. 140 mAh g⁻¹, a high specific capacity of ca. 600 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and a good rate capability. The stable discharge capacities of 500-515 mAh g⁻¹ and the columbic efficiencies of 95.8-98.1% were obtained at current density of 500 mA g⁻¹. The relatively large particle size of CoSn₂/Sn alloy composite powder is apparently favorable for the lowering of initial capacity loss of electrode, while the loose particle structural characteristic and the Co addition in Sn matrix should be responsible for the improvement of cycling stability of CoSn₂/Sn electrode.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

An optimized Ni doped LiFePO4/C nanocomposite with excellent rate performance

Both Ni doping and carbon coating are adopted to synthesize a nano-sized LiFePO₄ cathode material through a simple solid-state reaction. It is found that the Ni²⁺ has been successfully doped into LiFePO₄ without affecting the phospho-olivine structure from the XRD result. The images of SEM and TEM show that the size of particles is distributed in the range of 20-60 nm, and all the particles are coated with carbon completely. The results of XPS show the valence state of Fe and Ni in the LiFePO₄. The electronic conductivity of the material is as high as 2.1 × 10⁻¹ S cm⁻¹, which should be ascribed to the coefficient of the conductive carbon network and Ni doping. As a cathode material for lithium-ion batteries, the Ni doped LiFePO₄/C nanocomposite delivers a discharge capacity of 170 mAh g⁻¹ at 0.2 C, approaching the theoretical value. Moreover, the material shows excellent high-rate charge and discharge capability and long-term cyclability. At the high rates of 10 and 15 C, this material exhibits high capacities of 150 and 130 mAh g⁻¹, retaining 95% after 5500 cycles and 93% after 7200 cycles, respectively. Therefore, the as-prepared material is capable of such large-scale applications as electric vehicles and plug-in hybrid electric vehicles.     

LiFePO4 cathode power with high energy density synthesized by water quenching treatment

A water quenching (WQ) method was developed to synthesize LiFePO₄ and C-LiFePO₄. Our results indicate that this synthesis method ensures improved electrochemical activity and small crystal grain size. The synthetic conditions were optimized using orthogonal experiments. The LiFePO₄ sample prepared at the optimized condition showed a maximum discharge capacity of 149.8 mAh g⁻¹ at a C/10 rate. C-LiFePO₄ with a low carbon content of 0.93% and a high discharge specific capacity of 163.8 mAh g⁻¹ has also been obtained using this method. Water quenching treatment shows outstanding improvement of the electrochemical performance of LiFePO₄.     

Synthesis and electrochemical performance of novel loose structured submicro/micro-sized NiSnx alloy composites for lithium batteries

An effective method of carbothermal reduction was employed to prepare spherical microcrystal NiSn_x alloy powders from oxides of Sn and Ni used as anode materials for Li-ion battery. According to XRD, SEM and TEM analysis, the synthesized spherical NiSn_x powders show a loose submicro/micro-sized structure and a multi-phase composition. The prepared NiSn_x alloy composite electrode exhibits a stable discharge capacity of electrode is ca. 380 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and can be retained at 350 mAh g⁻¹ after 25 cycles. Moreover, NiSn_x alloys exhibit excellent high rate performance, i.e. stable discharge capacities of 300-310 mAh g⁻¹ and the coulombic efficiencies of 97.5-99.5% have been obtained at the current density of 500 mA g⁻¹. The loose submicro-sized particle structural characteristic and the Ni addition in Sn matrix should be responsible for the improvement of cycling stability of NiSn_x electrode. The carbothermal reduction method is simple, low-cost and mass-productive, which should be viable to other alloy composite materials system of rechargeable lithium ion batteries.     

LiNi0.8Co0.15Al0.05O2 cathode materials prepared by TiO2 nanoparticle coatings on Ni0.8Co0.15Al0.05(OH)2 precursors

Synthesis, electrochemical, and structural properties of LiNi_0.8Co_0.15Al_0.05O₂ cathodes prepared by TiO₂ nanoparticles coating on a Ni_0.8Co_0.15Al_0.05(OH)₂ precursor have been investigated by the variation of coating concentration and annealing temperature. TiO₂-coated cathodes showed that Ti elements were distributed throughout the particles. Among the coated cathodes, the 0.6 wt% TiO₂-coated cathode prepared by annealing at 750 °C for 20 h exhibited the highest reversible capacity of 176 mAh g⁻¹ and capacity retention of 92% after 40 cycles at a rate of 1C (=190 mA g⁻¹). On the other hand, an uncoated cathode showed a reversible first discharge capacity of 186 mAh g⁻¹ and the same capacity retention value to the TiO₂-coated sample at a 1C rate. However, under a 1C rate cycling at 60 °C for 30 cycles, the uncoated sample showed a reversible capacity of 40 mAh g⁻¹, while a TiO₂-coated one showed 71 mAh g⁻¹. This significant improvement of the coated sample was due to the formation of a possible solid solution between TiO₂ and LiNi_0.8Co_0.15Al_0.05O₂. This effect was more evident upon annealing the charged sample while increasing the annealing temperature, and at 400 °C, the coated one showed a more suppressed formation of the NiO phase from the spinel LiNi₂O₄ phase than the uncoated sample.     

Electrochemical study of NiO nanoparticles electrode for application in rechargeable lithium-ion batteries

Nickel oxide nanoparticles were synthesized via a simple and inexpensive microwave-assisted synthesis method within a fast reaction time of less than 20 min. The calcination of as-prepared precursor at 600 °C produces single phase nickel oxide. The lattice structure and morphology of the sample were investigated by X-ray diffraction, field-emission scanning electron microscopy and field-emission transmission electron microscopy. The particle size range of the nickel oxide nanoparticles varied from 50 to 60 nm. Nickel oxide nanoparticles exhibited good electrochemical performances as an anode material for lithium-ion batteries. The prepared nickel oxide anode revealed a large initial discharge capacity of 1111.08 mAh g⁻¹ at 0.03 C rate and retained 80% of initial capacity (884.30 mAh g⁻¹) after 20 cycles. Furthermore, at elevated rate of 3.7 C, the charge capacity of the nickel oxide electrode was as high as 253.1 mAh g⁻¹, which was 35% greater than that of commercial bulk nickel oxide (188 mAh g⁻¹). The enhancement of the electrochemical performance was attributed to the high specific surface area, good electric contact among the particles and easier lithium ion diffusion.     

Enhanced cycling performance of Fe3O4-graphene nanocomposite as an anode material for lithium-ion batteries

Fe₃O₄-graphene nanocomposite was prepared by a gas/liquid interface reaction. The structure and morphology of the Fe₃O₄-graphene nanocomposite were characterized by X-ray diffraction, scanning electron microscopy and high-resolution transmission electron microscopy. The electrochemical performances were evaluated in coin-type cells. Electrochemical tests show that the Fe₃O₄-22.7 wt.% graphene nanocomposite exhibits much higher capacity retention with a large reversible specific capacity of 1048 mAh g⁻¹ (99% of the initial reversible specific capacity) at the 90th cycle in comparison with that of the bare Fe₃O₄ nanoparticles (only 226 mAh g⁻¹ at the 34th cycle). The enhanced cycling performance can be attributed to the facts that the graphene sheets distributed between the Fe₃O₄ nanoparticles can prevent the aggregation of the Fe₃O₄ nanoparticles, and the Fe₃O₄-graphene nanocomposite can provide buffering spaces against the volume changes of Fe₃O₄ nanoparticles during electrochemical cycling.     

Submicron-sized cube-like α-Fe2O3 agglomerates as an anode material for Li-ion batteries

Submicron-sized cube-like α-Fe₂O₃ agglomerates were successfully fabricated via hydrothermal technique. The material showed a high reversible capacity of 900.2 mAh g⁻¹ and excellent capacity retention of 88.9% after 35 cycles at a current density of 40 mA g⁻¹. The initial columbic efficiencies of the as-prepared powder were 82.65 and 80.57% at current densities of 40 and 80 mA g⁻¹, respectively, which is higher than that of other α-Fe₂O₃ electrodes reported so far. We believe that the small crystal size and the high structure stability are responsible for the drastic improvement in initial coulombic efficiency and reversibility.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.