Phase structure and electrical properties of La<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped BiInO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ceramics with high curie temperature

The phase structure and electrical properties of pure and La2O3-doped Bi-InO3-PbTiO3 （BI-PT） ceramics were studied respectively. In （1 -x）BI-xPT （x=0.72-0.80） ceramics, the stability of tetragonal phase increased with increasing x, and pure perovskite structure was obtained for x=-0.80 ceramics. The phase transition temperature range was between 575 ℃ and 600 ℃ for x=0.72-0.80 ceramics, higher than that of PT （-490 ℃）. The c/a ratio almost linearly decreased with increasing La2O3 content in x-0.80 ceramics. It is believed that Pb^2＋ vacancies were formed by La^3＋ substituting Pb^2＋ in La2O3-doped BI-PT ceramics. Tc shifted to lower temperature by 30 ℃/mol% La2O3. The maximum dielectric constant 8557 around 559 ℃ was exhibited in 0.5mol%-doped BI-0.80PT ceramics. La2O3-doped ceramics could be poled resulting from decreasing of c/a ratio and improving of dielectric loss and resistivity. The maximum piezoelectric coefficient d33 was 12 pC/N for 2mol%-doped BI-0.80PT ceramics.     

Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Low-temperature sintering and microwave dielectric properties of Ba<Subscript>2</Subscript>Ti<Subscript>3</Subscript>Nb<Subscript>4</Subscript>O<Subscript>18</Subscript> ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO (< 1 wt%) considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 (< 3.5 wt%) remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.B...     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

Structure and dielectric properties of ZnO and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> doped BaO-TiO<Subscript>2</Subscript> system microwave ceramics

The microwave dielectric properties and microstructure of BaTi4.3ZnyO9.6＋y ＋0.02 mol% SnO2＋0.01 mol% MnCO3＋x mol% Nb2O5（x=0-0.05, y=0-0.08） system ceramics were studied as a function of the amount of ZnO and Nb2O5 doped. Addition of （y=0-0.05） ZnO and （x=0-0.025） Nb2O5 enhanced the reactivity and decreased the sintering temperature effectively. It also increased the dielectric constant ε r and quality factor Q（=1/tan 8） of the system due to the substitution of Ti^4＋ ions with incorporating Zn^2＋and Nb^5＋ ions, which was analyzed by the reaction ZnO＋Nb2O5＋ 3 TiTxTi →ZnTi＋ 2NbTi＋3TiO2. When the system doped with （y=0.05） ZnO and （x=0.025） Nb205 were sintered at 1 160 ℃ for 6 h, the εr. Qf0 value and rfwere 36.5, 42 000 GHz, and＋1.8 ppm/℃, respectively, at 5 GHz.     

Preparation of nanocrystalline BaTiO<Subscript>3</Subscript> ceramics

The high-dense nanocrystalline BaTiO₃ (BT) ceramics with grain size smaller than 100 nm have been successfully prepared by the two step sintering and the spark plasma sintering (SPS) process. The successive transitions in nanograin BT ceramics from rhombohedral to orthorhombic, tetragonal and cubic transitions, similar to those in coarse BT ceramics, were revealed by in-situ temperature dependent Raman spectrum. The multiphase coexistence and the diffused phase transition character were demonstrated in the 8 nm nanocrystalline BT ceramics. Supported by the National Basic Research Program of China (“973” Project) (Grant No. 2002CB613301) and the National Natural Science Foundation of China (Grant No. 50872093)     

Manufacture Process of 8Y2O3 Stabilized ZrO2 from Nano Powders

The manufacture process of 8 mol% Y2O3 stabilized ZrO2 ( YSZ ) from nano powders, including the forming and sintering stages, was studied. During the forming process of YSZ powders, the relative density of YSZ increases lineally with the forming press, and the sintering linear shrinkage of YSZ to the forming press compiles to the parabola trend. When the forming press exceeding 500MPa, the samples with lower shrinkage and high density were obtained. The sintering temperature of YSZ decreases greatly because of the small size and high active surface of YSZ powders. As a result, the beginning sintering temperature of YSZ made in the experiment is as low as 825℃, and the end sintering temperature is 1300-1350℃ . The relative density of YSZ ceramic by solid sintering at 1300-1350℃ is more than 97% , with little and small pores in the uniform microstructure.     

Solid Solution Characteristics of Pb（B1/3Nb2/3）O3-bascd Composite Ceramics

The solid solution characteristics of Pb（B1/3Nb2/3）O3-based （B=Zn^2＋, Mg^2＋, Ni^2＋） composite ceramics prepared by two-phase mixed-sintering method were developed based on dielectric measurements. Results show that there are double dielectric peaks for PZN-based composite ceramic, implying two phases coexist. However single dielectric peak was presented in PMN- and PNN-based composite ceramics, respectively. It is indicated that obvious solid solution reaction exists during the sintering process of these two systems. The effects of B-site ion difference on the solid solution characteristics were discussed by crystal chemistry. SEM was employed to investigated the microstructures of composite ceramics. The influences of solid solution reaction on grain growth were discussed.     

Effects of NaNbO3-Co2O3 Co-additive on the Properties of PZN-PZT Ceramics

NaNbO3-Co2O3 co-added PZN-PZT （PZCNNT） ceramics were prepared using conventional solid state reaction. The piezoelectric and dielectric properties were measured. The experimental results show that the addition of 0.3mo1% Co2O3 leads to low dielectric loss （tgδ） in PZCNNT ceramics and the proper addition of NaNbO3 not only improves piezoelectric properties but also decreases intensively dielectric loss and mechanical loss. The optimal ceramic having d33=310 pC/N, kp=0.59, εr=985, tgδ=0.0034, Qm=1380 was obtained.     

Measurement of refractive indices and thermal refractive index coefficients of Cr<Superscript>3+</Superscript>: Be<Subscript>3</Subscript>Al<Subscript>2</Subscript>Si<Subscript>6</Subscript>O<Subscript>18</Subscript> by auto-collimation method

The principal refractive indices and the thermal refractive index coefficients for Be₃Al₂Si₆O₁₈ crystal doped with 1.01wt% Cr₂O₃ have been accurately measured by the auto-collimation method at wavelengths of 0.488, 0.53975, 1.064, 1.0795 and 1.3414 μm, and temperatures of 308.2, 328.6, 359.1 and 395.4 K respectively. Based on the measured results of principal indices of 0.488, 0.6328, 1.0795 and 1.3414μm, the Sellmeier’s equations and the thermal refractive index coefficients have been obtained, and the result has been proven to be accurate by error analysis.     

Preparation, Characterization and Dielectric Property of Sr5 LaTi3 Nb7O30 Ceramic

Sr5LaTi3Nb7O30 ceramic was prepared by the conventional high temperature solid-state reaction route. The sintered samples were characterized by X-ray diffraction, scanning electron microscopy ( SEM ), differential thermal calorimetry ( DSC ) and dielectric measurements. The results show Sr5LaTi3Nb7O30 belongs to paraclectric phase of filled tetrngonal TB structure at room temperature, and undergoes a diffuse phase transition in the temperature range of -54-34℃ . And Sr5LaTi3Nb7O30 ceramic shows a high dielectric constant of 479 with a low dielectric loss of 0.005 at 1MHz . In comparison with Ba-based ceramics with TB structure, the temperature coefficients of the dielectric constant ( τt ) is significantly reduced.     

Dielectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramics by impedance spectroscopic method

Various lead-free ceramics have been investigated in search for new high-temperature dielectrics. In particular, Bi₄Ti₃O₁₂ is a type of ferroelectric ceramics, which is supposed to replace leadcontaining ceramics for its outstanding dielectric properties in the near future. Ferroelectric ceramics of Bi₄Ti₃O₁₂ made by conventional mixed oxide route have been studied by impedance spectroscopy in a wide range of temperature. X-ray diffraction patterns show that Bi₄Ti₃O₁₂ ceramics are a single-phase of ferroelectric Bi-layered perovskite structure whether it is calcined at 800 °C or after sintering production. This study focused on the effect of the grain size on the electric properties of BIT ceramics. The BIT ceramics with different grain sizes were prepared at different sintering temperatures. Grain becomes coarser with the sintering temperature increasing by 50 °C, relative permittivity and dielectric loss also change a lot. When sintered at 1 100 °C, r values peak can reach 205.40 at a frequency of 100 kHz, the minimum dielectric losses of four different frequencies make no difference, all close to 0.027. The values of E _a range from 0.52 to 0.68 eV. The dielectric properties of the sample sintered at 1 100 °C are relatively better than those of the other samples by analyzing the relationship of the grain, the internal stresses, the homogeneity and the dielectric properties. SEM can better explain the results of the dielectric spectrum at different sintering temperatures. The results show that Bi₄Ti₃O₁₂ ceramics are a kind of dielectrics. Thus, Bi₄Ti₃O₁₂ can be used in high-temperature capacitors and microwave ceramics.     

Preparation and ferroelectric properties of Bi<Subscript>3.4</Subscript>Ce<Subscript>0.6</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films grown by sol-gel method

We have investigated the preparation and properties of Bi_3.4Ce_0.6Ti₃O₁₂ thin films. The Bi_3.4Ce_0.6Ti₃O₁₂ thin films were fabricated on the Pt/Ti/SiO₂/Si substrates using sol-gel method. The structure and morphology of the films were characterized using X-ray diffraction and atomic force microscopy. The thin films showed a perovskite phase and dense microstructure. The dielectric constant and the dissipation factor of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were about 172 and 0.031 at 1 kHz, respectively. The 2P _r and 2E _c of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were 67.1 μC/cm² and 299.7 kV/cm, respectively, under an applied field of 600 kV/cm. The Bi_3.4Ce_0.6Ti₃O₁₂ film did not show fatigue up to 4.46×10⁹ switching cycles at a frequency of 1 MHz, and showed good insulating behavior according to the test of leakage current. Supported by the Natural Science Foundation of Hubei Province (Grants No. 2004ABA082)     

Molten Salt Synthesis of Ba（ Mgl／3Nb2／3 ）O3 Powder

The single-phrase Ba(Mgl/3Nb2/3)O3(BMN) powder was saccessfully prepared by the KCImolten salt synthesis(MSS) method. The temperature for single-phase BMN powders by MSS was about 400℃ lower than that by the solid-phase method. The average particle size (APS) was about 0.91,u.m at 900℃ and increased with increasing synhesis temperature. Based on the APS, the activation energy for particle growth in theMSS, whose value was 64. 1kJmol^-1.was attained. The sinterability of the powder prepared by MSS method wasbetter than that pretared by solid-phase method.     

Self-Propagating High-Temperature Reduetive Synthesis of TiB2-Al2O3 Composite Powders

TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM） analyses show the presence of TiB2 and Al2O3 only in the composite powders produced by SHS. The powders are uniform and free-agglomerate. Transmission electron microscopy （TEM） and high resolution electron microscopy （HREM） observation of microstructure of the composite powders indicate that the interfaces of the TiB2-Al2O3 bond well, without any interfacial reaction products. It is proposed that the good interfacial bonding of the composite powders can be resulted from the TiB2 particles crystallizing and growing on the Al2O3 particles surface with surface defects acting as nucleation centers.     

Nanocomposite films of V<Subscript>2</Subscript>O<Subscript>5</Subscript>−MoO<Subscript>3</Subscript> xerogel with poly ethylene oxide intercalation

Poly ethylene oxide (PEO)_x−V₂O₅−V₂O₅−MoO₃ (x=0, 0.5, 1) films were prepared by the sol-gel method. The synthesis and structure of the films were investigated by XRD, TG-DTA, FTIR, etc. The results show that V₂O₅−MoO₃ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1. 7898 nm at x=1 after the nanocomposite films were dried, and PEO in the interlayer changes the interface structure by forming hydrogen bonds with V=0 bands. CV measurement indicates that the intercalation of PEO improves insertion/extration properties of Li⁺ ions in the interlayer. ZHENG Jin-xia: Born in 1976 Funded by the National Natural Science Foundation of China (No. 50172036) and Natural Science Foundation of Hubei Province(No. 2001ABB083)     

Structure and Electric Properties of （1-x）（Bi1/2Na1/2） TiO3-xBaTiO3 Systems

The structural, dielectric and piezoelectric properties of （1-x）（Bi1/2Na1/2） TiO3-xBaTiO3 ceramics were investigated for the compositional range, x=0.02, 0.04, 0.06, 0.08, 0.10. The samples were synthesized by a conventional solid-state reaction technique. All compositions show a single perovskite structure, and X-ray powder diffraction patterns can be indexed using a rhombohedral structure. Lattice constants and lattice distortion increase while the amount of BaTiO3 increases. The X-ray diffraction results show the morphotropic phase boundary （MPB） of （1-x）（Bi1/2Na12） TiO3-xBaTiO3 exists in near x=0.06-0.08. Temperature dependence of dielectric constant eT33/ε0 measurement reveals that all compositions experience one structural phase and two ferroelectric phases transition below 400℃： rhombohedral （or rhombohedral plus tetragonal） ferroelectric phase ←→ tetragonal antiferroelectric phase ←→ tetragonal paraelectric phase. Relaxor behaviors exist in the course of ferroelectric to antiferroelectric phase transition. Dielectric and piezoelectric properties are enhanced in the MPB range for （ 1-x）（Bi1/2Na1/2）TiO3-xBaTiO3.     

Dielectric tunable properties of BaTi<Subscript>4</Subscript>O<Subscript>9</Subscript>-doped Ba<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>TiO<Subscript>3</Subscript> microwave composite ceramics

BaTi₄O₉-doped Ba_0.6Sr_0.4TiO₃ (BST) composite ceramics were prepared by the conventional solid-state reaction and their structure, dielectric nonlinear characteristics and microwave dielectric properties were investigated. The secondary phase of the orthorhombic structure Ba₄Ti₁₃O₃₀ is formed among BST composite ceramics with the increase of BaTi₄O₉. At the same time, a duplex or bimodal grains size distribution shows fine grains in a coarse grain matrix. The degree of frequency dispersion of dielectric permittivity below T _m is increased initially and then decreased with respect to BaTi₄O₉. As the BaTi₄O₉ content increases, the tunability of composite ceramics decreases, while the Q value increases. Interestingly, 70 wt% BaTi₄O₉-doped BST has a tunability ∼4.0% (under 30 kV/cm biasing) versus a permittivity ∼68 and quality factor ∼134.1 (at ∼3.2 GHz). Supported by the Ministry of Science and Technology of China through 973-project (Grant No. 2009CB623302), the Cultivation Fund of the Key Scientific and Technical Innovation Project, Ministry of Education of China (Grant No.707024), Shanghai Committee of Science and Technology (Grant No. 07DZ22302), and Shanghai Foundation Project under 06JC14070     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> content on residual stress and properties of CAS glass-ceramics

The structure and properties of the glass-ceramics were tested with X-ray diffraction testing instrument,correlative software,and other modern testing means.Then the effect of Al2O3 content on internal stresses in CaO-Al2O3-SiO2 glass-ceramics was studied deeply.In order to study the relationship of Al2O3 to the residual stress of CaO-Al2O3-SiO2 glass-ceramics,X-ray diffraction ＂sin2ψ＂ was used.The means utilized the x radial incidence produced from cathode radial tube,and took the space between crystals as measurement of strain.When the stresses produced,the space between crystals changed and the diffraction peak moved during Bragg diffraction.The magnitude of movement is related to the stresses.The experimental results show the residual stress is considerably high and Al2O3 can influence the mechanical properties of this material hugely.     

Low-temperature sintering and microwave dielectric properties of Li2MgTi3O8 ceramics doped with BaCu（B2O5）

The influences of BaCu(B₂O₅) (BCB) addition on sintering, microstructure and microwave dielectric properties of Li₂MgTi₃O₈ ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu(B₂O₅) addition can effectively reduce the sintering temperature to 900 °C, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of ɛ _r=24.5, Q×f =24 622 GHz, τ _f=4.2×10⁻⁶ °C⁻¹ are obtained for 1.0% BCB-doped Li₂MgTi₃O₈ ceramics sintered at 900 °C for 3 h. The BCB-doped Li₂MgTi₃O₈ ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.