High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

Potential of producing carbon fiber from biorefinery corn stover lignin with high ash content

The possibility of producing carbon fiber from an industrial corn stover lignin was investigated in the present study. As‐received, high‐ash containing lignin was subjected to methanol fractionation, acetylation, and thermal treatment prior to melt spinning and the changes in physiochemical and thermal properties were evaluated. Methanol fractionation removed most of the impurities in the raw lignin and also selectively removed the molecules with high melting points. However, neither methanol fractionation nor thermal treatment rendered melt‐spinnable precursors. The precursors were highly viscous and decomposed easily at low temperatures, attributed to the presence of H, G phenolic units, and abundant hydroxycinnamate groups in herbaceous lignin. A two‐step acetylation of methanol fractionated lignin greatly improved the mobility of lignin, while enhancing the thermal stability of the precursor during melt‐spinning. Fourier Transform Infrared and 2D‐NMR analysis showed that the contents of phenolic and aliphatic hydroxyls, as well as the hydroxycinnamates, decreased in the acetylated precursors. The optimum precursor was a partially acetylated lignin with a glass transition temperature of 85 °C. Upon oxidative stabilization and carbonization, the carbon fibers with an average tensile strength of 454 MPa and modulus of 62 GPa were obtained. The Raman spectroscopy showed the I_D/I_G ratio of the carbon fiber was 2.53. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45736.     

Carbon fibers derived from UV‐assisted stabilization of wet‐spun polyacrylonitrile fibers

A rapid, dual‐stabilization route for the production of carbon fibers from polyacrylonitrile (PAN) precursor fibers is reported. A photoinitiator, 4,4′‐bis(diethylamino)benzophenone, was added to PAN solution before the fiber wet‐spinning step. After a short UV treatment that induced cyclization and crosslinking at a lower temperature, precursor fibers could be rapidly thermo‐oxidatively stabilized and successfully carbonized. Scanning electron microscopy micrographs show no deterioration of the microstructure or hollow‐core formation in the fibers due to UV treatment or presence of photoinitiator. Fast‐thermally stabilized pure PAN‐based carbon fibers show hollow‐core fiber defects due to inadequate thermal stabilization, but such defects were not observed in carbon fibers derived from fast‐thermally stabilized fibers that contained photoinitiator and were UV treated. Tensile testing results confirm that fibers containing 1 wt % photoinitiator and UV treated for 5 min display higher tensile modulus than all other sets of thermally stabilized and carbonized fibers. Wide‐angle X‐ray diffraction results show a higher development of the aromatic structure and molecular orientation in thermally stabilized fibers. No significant increase in interplanar spacing or decrease in crystals size were observed within the UV‐stabilized carbon fibers containing photoinitiator, but such fibers retain a higher extent of molecular orientation when compared with control fibers. These results establish for the first time, the positive effect of the external addition of photoinitiator and UV treatment on the properties of the PAN‐based fibers, and may be used to reduce the precursor stabilization time for faster carbon fiber production rate. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40623.     

Processing,structure, and properties of gel spun PAN and PAN/CNT fibers and gel spun PAN based carbon fibers

Polyacrylonitrile (PAN) and PAN/carbon nanotube (PAN/CNT) fibers were manufactured through dry‐jet wet spinning and gel spinning. Fiber coagulation occurred in a solvent‐free or solvent/nonsolvent coagulation bath mixture with temperatures ranging from ?50 to 25°C. The effect of fiber processing conditions was studied to understand their effect on the as‐spun fiber cross‐sectional shape, as well as the as‐spun fiber morphology. Increased coagulation bath temperature and a higher concentration of solvent in the coagulation bath medium resulted in more circular fibers and smoother fiber surface. as‐spun fibers were then drawn to investigate the relationship between as‐spun fiber processing conditions and the drawn precursor fiber structure and mechanical properties. PAN precursor fiber tows were then stabilized and carbonized in a continuous process for the manufacture of PAN based carbon fibers. Carbon fibers with tensile strengths as high as 5.8 GPa and tensile modulus as high as 375 GPa were produced. The highest strength PAN based carbon fibers were manufactured from as‐spun fibers with an irregular cross‐sectional shape produced using a ?50°C methanol coagulation bath, and exhibited a 61% increase in carbon fiber tensile strength as compared to the carbon fibers manufactured with a circular cross‐section. POLYM. ENG. SCI., 55:2603–2614, 2015. © 2015 Society of Plastics Engineers     

High‐temperature DSC study of polyacrylonitrile precursors during their conversion to carbon fibers

The evolution of structure, the changes of properties during the preoxidation, precarbonization, and carbonization of different polyacrylonitrile (PAN) precursors were firstly studied in detail by means of using high‐temperature differential scanning calorimetry (DSC) to characterize with continuous heating from 25 to 1400°C. It was essential to study the thermal behavior of PAN precursors so that proper temperature was determined. Three precursors with different composition, P1: acrylonitrile/itaconic acid (AN/IA) = 98/2 (wt/wt); P2: acrylonitrile/acrylamide (AN/AM) = 98/2 (wt/wt); P3: acrylonitrile/ammonium salt of itaconic acid (AN/AIA) = 98/2 (wt/wt) were, respectively, selected in this study. Comparative results of the DSC curves showed that the heating history influenced greatly the heat quantities released and exothermic position at low temperature of DSC curve, but influenced slightly at higher temperature. Aromatic index, carbon yield (W_c) and weight loss (η) can be calculated. After adjusting the temperature in preoxidation and precarbonization and carbonization technology depending on high‐temperature DSC, the high performance carbon fibers were obtained that tensile strength is 3.56–4.16 GPa, modulus is 235–243 GPa. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Characteristics of wet‐spun and thermally treated poly acrylonitrile fibers

The performance of carbon fibers depends on the quality of the precursor and the conditions of the thermal treatment. In detail, for a PAN precursor fiber the viscosity of a spinning dope and the draw ratio during the spinning process needs to be considered. Through wet spinning, different types of PAN precursor fibers with defined spinning parameters, including solid content, solvent content in a bath, and especially draw ratio resulting in defined cross section diameters, were fabricated and analyzed with tensile tests, density investigations, SEM, TGA‐MS, FTIR, and XRD. The results show that the mechanical properties of the fibers correlate to crystallinity. The cross section diameter is strongly related to the morphology of the fibers after thermal treatment. By extending the postdrawing of PAN fibers high tenacities were obtained at the cost of the cross section shape. In addition, TGA measurements reveal trapped residues of the wet spinning process as well as show several chemical reactions takes place at the same time at different temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43698.     

Effect of the solvent type on the formation and physical properties of polyacrylonitrile fibers via a solvent‐free coagulation bath

Polyacrylonitrile (PAN) fibers were fabricated via a dry‐jet wet‐spinning technique, and a solvent‐free coagulation bath system was adopted. The effects of different types of dope solvent on the formation and physical properties of the PAN fibers were investigated. Dimethylformamide and dimethyl sulfoxide (DMSO) were selected as the solvents and were added to a spinning solution consisting of 18 wt % PAN. The PAN fibers were examined with field emission scanning electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The field emission scanning electron micrographs revealed that the PAN fibers with the DMSO solvent exhibited a more circular shape and a smoother skin. The PAN fibers with the DMSO solvent had their glass‐transition temperature (T_g) at 121°C. This study indicated that the different types of dope solvent used in the dope preparation did not affect T_g of the PAN fibers because of the solvent‐free coagulation bath system; however, they significantly affected the physical formation of the PAN fibers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The novel alginate/N‐succinyl‐chitosan antibacterial blend fibers

Alginate/ N‐Succinyl‐chitosan (SCS) blend fibers, prepared by spinning their mixture solution through a viscose‐type spinneret into a coagulating bath containing aqueous CaCl₂, were studied for structure and properties with the aid of infrared spectroscopy (IR) and X‐ray diffraction (XRD). The results indicated a good miscibility between alginate and SCS, because of the strong interaction from the intermolecular hydrogen bonds. The best values of the dry tensile strength and breaking elongation were obtained when SCS content was 30 wt %. The wet tensile strength decreased with the increase of SCS content, and the wet breaking elongation achieved maximum value when the SCS content was 30 wt %. Introduction of SCS in the blend fiber improved water‐retention properties of blend fiber compared to pure alginate fiber. Antibacterial fibers, obtained by treating the fibers with aqueous solution of silver nitrate, exhibited good antibacterial activity to Staphylococcus aureus. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The index of dry‐jet wet spinning for polyacrylonitrile precursor fibers

A new spinning index for a PAN precursor fiber is proposed that includes the viscosity of a spinning dope, the thermodynamic affinity, and the draw ratio during the spinning process. Through dry‐jet wet spinning, six types of PAN precursor fibers with different spinning parameters, including solid content, solvent content in a bath, and draw ratio, were fabricated and analyzed with tensile tests, SEM, and XRD. The results show that the spinning index can reflect the mechanical properties of the fibers but is less indicative of crystallinity. Hence, the current spinning index is recommended for use as an indicator for the mechanical properties of PAN precursor fibers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41265.     

Wet-spinning assembly of continuous and macroscopic graphene oxide/polyacrylonitrile reinforced composite fibers with enhanced mechanical properties and thermal stability

Polyacrylonitrile (PAN) composite microfibers with different contents of graphene oxide (GO) were fabricated via wet-spinning route in this work. Based on nonsolvent-induced phase separation theory, N,N-dimethyl formamide/water mixture system was employed as coagulation bath, nonsolvent (water) diffused into PAN spinning solution and led to a quick PAN fiber solidification. Nematic liquid crystal state of GO dispersions and GO/PAN spinning solutions were determined via polarized optical microscopy images, and the morphology and structure of the composite fibers were characterized via scanning electron microscope, Transmission electron microscopy, Fourier transform infrared spectra, and X-ray diffraction. 1 wt % GO/PAN composite fibers exhibited outstanding mechanical properties, 40% enhancement in tensile strength and 34% enhancement in Young's modulus compared with pure PAN fiber. The results of dynamic mechanical analysis indicated that the composite fiber with 1 wt % GO performed the best thermal mechanical property with 5.5 GPa and 0.139 in storage modulus and loss tangent, respectively. In addition, thermogravimetric analysis showed that thermal stability of the composite fibers enhanced with the increasing GO contents. GO/PAN composite fibers can be as the candidate of carbon fiber precursor, high performance fibers, and textiles applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46950.     

Dry jet‐wet spinning of bagasse/N‐methylmorpholine‐N‐oxide hydrate solution and physical properties of lyocell fibres

Sugarcane bagasse, a cheap cellulosic waste material, was investigated as a raw material for producing lyocell fibers at a reduced cost. In this study, bagasse was dissolved in N‐methylmorpholine‐N‐oxide (NMMO) 0.9 hydrate, and fibers were prepared by the dry jet‐wet spinning method with coagulation in an aqueous NMMO solution. The effects of NMMO in 0 to 50% concentrations on the physical properties of fibers were investigated. The coagulating bath contained water/NMMO (10%) solution produced fiber with the highest drawability and highest physical properties. The cross‐section morphology of these fibers reveals fibrillation due to the high degree of crystallinity and high molecular orientation. In the higher NMMO concentrated baths (30 to 50%), the prepared fibers were hollow inside, which could be useful to make highly absorbent materials. The lyocell fibers prepared from bagasse have a tensile strength of 510 MPa, initial modulus of 30 GPa, and dynamic modulus of approximately 41 GPa. These properties are very comparable with those of commercial lyocell fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

High‐performance copoly(benzimidazole‐benzoxazole‐imide) fibers: Fabrication,structure, and properties

Novel high‐performance copolyimide (co‐PI) fibers containing benzimidazole and benzoxazole ring in the main chain were prepared by a two‐step spinning via the poly(amic acid)s. Effects of the incorporated benzimidazole and benzoxazole units on the micro‐structure and properties of co‐PI fibers were investigated. Fourier transform infrared (FTIR) results indicated that hydrogen bonding is formed in the co‐PI fibers. The co‐PI fibers exhibited discernible crystallization peaks at 14°～15° and 23°～26° (2θ), showing crystalline‐like structure. Moreover, the packing type of benzimidazole‐imide units determined the macromolecules packing of co‐PIs. It was amazedly found that the co‐PI fibers exhibited higher tensile strength and initial modulus than those of corresponding homo‐PI fibers, reaching tensile strength of 2.2–2.6 GPa, initial modulus of 99.1–113.2 GPa. The results of dynamic mechanical analysis (DMA) indicated co‐PI2 fiber had a positive T_g deviation due to the presence of strong intermolecular hydrogen bonding between benzimidazole‐imide and benzoxazole‐imide units, which maybe lead to the effective stress transfer between benzimidazole‐imide units and benzoxazole‐imide units. In addition, the obtained PI fibers exhibited excellent thermal properties with the 10% weight loss temperatures under N₂ in the range of 574–585°C. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42001.     

On the characterization and spinning of an organic‐purified lignin toward the manufacture of low‐cost carbon fiber

A Kraft hardwood lignin (HWL) and an organic‐purified hardwood lignin (HWL‐OP) were evaluated as potential precursors for the production of low‐cost carbon fibers. It was found that the unpurified HWL exhibited poor spinnability while the HWL‐OP exhibited excellent spinnability characteristics. Fibers of various diameters were obtained from the HWL‐OP. Thermostabilization studies showed that oxidative stabilization can only be used to convert HWL‐OP‐based fibers into carbon fibers if extremely low heating rates are applied. Carbonized lignin‐based fibers had tensile strength of 0.51 GPa and tensile modulus of 28.6 GPa. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of coagulation conditions on solvent diffusions and the structures and tensile properties of solution spun polyacrylonitrile fibers

Polyacrylonitrile (PAN) fibers were spun by solution spinning. In this work, two coagulation compositions, dimethyl sulfoxide (DMSO)/water and methanol, were used, and coagulation temperatures were varied from ?20 to 0 to 20 °C. The coagulation compositions and temperatures strongly affected the solvent diffusion processes, the structures of as‐spun fibers, and the tensile properties of final drawn fibers. When DMSO/water was used as coagulation bath, non‐solvent (water) diffused into PAN fibers and led to a quick PAN solidification. By comparison, when methanol was used as coagulation bath, no or minimal amount of methanol diffused inward to the fibers. The different solvent diffusion behaviors in DMSO/water and methanol baths led to different structures of as‐spun PAN fibers. It was observed that the tensile properties of final drawn fibers strongly depended on the coagulation conditions. When methanol was used as coagulation bath and the bath temperature was ?20 °C, PAN fibers was found to possess the best tensile properties, a tensile strength of 0.89 GPa and young modulus of 20.4 GPa. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44390.     

Chitin nanocrystal reinforced wet‐spun chitosan fibers

Chitosan (CS) has been extensively studied and found wide applications in the field of biomedicine because of its favorable biological properties. Normal CS fibers are manufactured either by wet‐spinning or by dry‐jet wet‐spinning. However, the poor tensile strength of CS fibers raises much concern. The present study uses chitin nanocrystal (ChiNC), a stiff rod‐like nanofiller, to enhance the mechanical properties of wet‐spun CS fibers. Owing to the good compatibility between CS and ChiNC, the nanoparticles are well distributed in the CS matrix. When the ChiNCs loading is 5 wt %, the optimal mechanical properties of CS fibers are obtained, and the peak stress is 2.2 cN/dtex and modulus is 145.6 cN/dtex, which are increased by 57% and 84.5%, respectively, compared to that of nonfilled CS fibers under the same processing condition. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40852.     

Polyacrylonitrile/acrylamide‐based carbon fibers prepared using a solvent‐free coagulation process: Fiber properties and its structure evolution during stabilization and carbonization

Polyacrylonitrile (PAN)/acrylamide (AM) fibers were fabricated via dry‐jet wet spinning process using a solvent‐free coagulation bath. The effects of AM loading as comonomer on the mechanical and thermal properties of PAN‐based carbon fiber have been studied. The thermal stability and mechanical stability of the fibers were characterized using differential scanning calorimetry (DSC) and tensile testing. Fibers fabricated from PAN with 5 wt% AM had the highest Young Modulus at 5.54 GPa. It also showed better exothermic trend process with broader exothermic peak and lower initiation stabilization temperature compared with homopolymer PAN. The elemental composition and chemical structure evolution of the fibers during the heat treatment processes were evaluated by elemental analyzer and Fourier Transform Infrared Spectroscopy. Crystal structure evolution of the fibers during the heat treatment process was elucidated by X‐ray diffraction (XRD) analysis. The elemental analyzer, XRD and FTIR results revealed that pyrolysis process used had successfully transformed PAN/AM fibers produced from solvent free coagulation bath into carbon fibers that were comparable with the conventional coagulation bath. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Polyacrylonitrile solution homogeneity study by dynamic shear rheology and the effect on the carbon fiber tensile strength

Poly(acrylonitrile‐co‐methacrylic acid) (PAN‐co‐MAA)/N,N‐dimethylformamide (DMF) solutions were prepared and dynamic shear rheology of these solutions were investigated. With increasing stirring time up to 72 h at 70°C, the polymer solution became less elastic (more liquid‐like) with a ～60% reduction in the zero‐shear viscosity. Relaxation spectra of the PAN‐co‐MAA/DMF solutions yield a decrease in relaxation time (disentanglement time, τ_d), corresponding to an about 8% decrease in viscosity average molecular weight. The log‐log plot of G′ (storage modulus) versus G″ (loss modulus) exhibited an increase in slope as a function of stirring time, suggesting that the molecular level solution homogeneity increased. In order to study the effect of solution homogeneity on the resulting carbon fiber tensile strength, multiple PAN‐co‐MAA/DMF solutions were prepared, and the precursor fibers were processed using gel‐spinning, followed by continuous stabilization and carbonization. The rheological properties of each solution were also measured and correlated with the tensile strength values of the carbon fibers. It was observed that with increasing the slope of the G′ versus G″ log‐log plot from 1.471 to 1.552, and reducing interfilament fiber friction during precursor fiber drawing through the addition of a fiber washing step prior to fiber drawing, the carbon fiber strength was improved (from 3.7 to 5.8 GPa). This suggests that along with precursor fiber manufacturing and carbonization, the solution homogeneity is also very important to obtain high strength carbon fiber. POLYM. ENG. SCI., 56:361–370, 2016. © 2016 Society of Plastics Engineers     

Lignin-based carbon fibers for composite fiber applications

Carbon fibers have been produced for the first time from a commercially available kraft lignin, without any chemical modification, by thermal spinning followed by carbonization. A fusible lignin with excellent spinnability to form a fine filament was produced with a thermal pretreatment under vacuum. Blending the lignin with poly(ethylene oxide) (PEO) further facilitated fiber spinning, but at PEO levels greater than 5%, the blends could not be stabilized without the individual fibers fusing together. Carbon fibers produced had an over-all yield of 45%. The tensile strength and modulus increased with decreasing fiber diameter, and are comparable to those of much smaller diameter carbon fibers produced from phenolated exploded lignins. In view of the mechanical properties, tensile 400–550 MPa and modulus 30–60 GPa, kraft lignin should be further investigated as a precursor for general grade carbon fibers.     

Investigation the jet stretch in PAN fiber dry‐jet wet spinning for PAN‐DMSO‐H2O system

The jet stretch of dry‐jet wet spun PAN fiber and its effects on the cross‐section shape of fibers were investigated for a PAN‐DMSO‐H₂O system. Clearly, the spinning parameters, such as dope temperature, bath concentration, bath temperature, and air gap, all influenced the jet stretch. Also, under uniform conditions, the postdrawing ratio as well as that of jet stretch changed. Under given conditions, as the bath temperature was below 30°C or above 45°C, jet stretch had little effect on the cross‐sectional shapes of PAN fiber. Within the temperature of 30–45°C, fiber's cross‐section shapes change obviously from round over an approximate circular shape into to an elliptical or a flat shape. The scope of jet stretch produced PAN fiber with circular cross‐section was bigger than that in wet spinning. These results indicated that appropriate air gap height, under milder formation conditions in dry‐jet wet spinning, could result in higher jet stretch and higher postdrawing ratio. The appropriate jet stretch and postdrawing ratio could result in circular profile of PAN fiber, which were helpful to produce round PAN precursor with finer size and better properties for carbon fiber. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

High‐performance fibers based on copolyimides containing benzimidazole and ether moieties: Molecular packing,morphology, hydrogen‐bonding interactions and properties

High‐performance copolyimide (co‐PI) fibers were prepared via the wet spinning process of co‐polyamide acid precursors based on 3,3′,4,4′‐biphenyldianhydride (BPDA) and a mixture of three diamines namely p‐phenylene diamine (p‐PDA), 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (BIA), and 4,4′‐oxidianiline (ODA), followed by drawing and imidization at high temperatures. Effects of the ODA and BIA contents on the molecular packing, morphology, hydrogen‐bonding interactions, mechanical and thermal properties of the prepared fibers were investigated. The mechanical properties of the co‐PI fibers were improved with the addition of ODA and BIA, and they reached the optimum tensile strength of 2.7 GPa and modulus of 94.3 GPa. Wide‐angle X‐ray diffraction results (WAXD) showed that the co‐PI fibers exhibited highly oriented structure along the fiber direction with low degree of lateral packing orders in the transverse direction. Two‐dimensional small‐angle X‐ray scattering (2D‐SAXS) revealed that the incorporation of ODA resulted in the reduction in radius, length, misorientation, and internal surface roughness of the microvoids in the fibers. Fourier transform infrared (FTIR) results indicated that hydrogen‐bonding formed between the BIA and cyclic imide units effectively strengthened the intermolecular interactions. The co‐PI fibers exhibited excellent thermal and thermal‐oxidative stability, with a 5%‐weight‐loss temperature of 578°C under N₂ and 572°C in air. POLYM. ENG. SCI., 55:2615–2625, 2015. © 2015 Society of Plastics Engineers