电感耦合等离子体发射光谱法直接测定铜矿石中银铜铅锌

采用硝酸-氢氟酸-高氯酸混合酸消化处理样品,电感耦合等离子体发射光谱法同时测定了铜矿石中的银、铜、铅和锌。较系统地研究了仪器的最佳化工作参数,采用基体匹配和校正因子相结合的办法校正样品的基体干扰和光谱干扰。方法检出限为:银3.15μg/g,铜4.00μg/g,铅12.0μg/g,锌6.00μg/g(稀释因子500),精密度(RSD,n=12)在0.38%~4.55%。方法经国家一级多金属矿石标准物质验证,测定值与标准值吻合,结果准确可靠。     

盐酸介质下火焰原子吸收光谱法测定铅精粉中的高含量银

对于铅精粉中银含量高的样品,特别是银含量大于1000μg/g和含有机质及含硫量高的铅精粉样品,在湿法处理样品过程中因存在难溶解、易包裹、易沉淀,使得银含量的测定结果偏低。针对上述问题,本文从优化样品消解方法出发,研究了铅精矿中银的最佳分析条件。即首先用盐酸除硫,再用硝酸-氢氟酸-高氯酸溶解试样,在20%盐酸介质中,用火焰原子吸收光谱仪于波长328.07 nm测定银的含量。在此实验条件下溶矿完全,提取液清澈,无沉淀。用铅精粉国家标准物质GBW07167、GBW07172和标准样品Pb-3进行验证,方法精密度(RSD,n=12)为1.0%~3.2%,银的测定结果与其标准值吻合较好。本方法制备的样品溶液稳定性较好,分析快速,可测定的银含量高达3000μg/g。     

焙烧分离-氢化物发生-原子荧光光谱法测定铜铅锌矿石中的硒

样品经艾斯卡试剂(碳酸钠和氧化锌)半熔法分解,沸水提取,使硒与主量金属元素铜、铅、锌及其他过渡金属和贵金属元素得到分离;滞留在溶液中的干扰元素,通过在酸性介质中加铁盐来掩蔽。采用焙烧分离-氢化物发生-原子荧光光谱法测定铜矿石、铅矿石和锌矿石中的硒,干扰少、灵敏度高。确定了最佳条件为盐酸浓度30%,硼氢化钾浓度20 g/L,铁盐浓度1 mg/mL;干扰元素的允许量铜为40 mg/L,铅为8 mg/L,锌为400 mg/L。同时对铜、铅、锌主量金属元素进行分离效率试验,效果好。方法检出限为0.0203μg/g,测定范围为0.15～100μg/g。经全国不同地区7家实验室采用铜矿石、铅矿石和锌矿石国家标准物质验证,精密度的重复性限和再现性良好,准确度高。建立的方法也适合于土壤及多金属矿物中硒的测定。     

电感耦合等离子体发射光谱法测定西藏矽卡岩型铜多金属富矿石中8种成矿元素

矽卡岩型铜多金属富矿石是西藏特有矿产,具有成矿元素多样且含量普遍较高的特点,矿物类型主要为硫化物型,成矿元素有Cu、Pb、Zn、Fe、Ag、Bi、Cd、Co等。采用湿法处理此类样品时常因银、铅等元素含量较高出现难溶解、易沉淀现象,导致测定结果偏低。本文采用盐酸预处理、硝酸-氢氟酸-高氯酸溶矿体系,能有效除去样品中的硫,样品分解效果好,选择稀释倍数为1000、溶液介质为10%盐酸,样品溶液不会产生沉淀,采用电感耦合等离子体发射光谱法测定各待测元素均可获得较好的准确度、精密度。方法测定范围为:Cu 0.0056%~20.0%,Pb 0.0087%~20.0%,Zn 0.0031%~20.0%,Fe 0.0090%~20.0%,Ag 5.40~3000μg/g,Bi 10.8~5000μg/g,Cd 0.69~5000μg/g,Co 2.09~5000μg/g。用国家标准物质进行验证,方法准确度小于5.40%,精密度(RSD,n=11)小于4.41%。该方法具有前处理流程简单、分析速度快、同时测定元素多、线性范围宽等优点,经实际样品测试与不同方法分析数据吻合。     

全反射X射线荧光光谱法同时测定复混肥料中钒铬锰铁镍铜锌铅

样品经硝酸微波消解,以镓为内标,采用全反射X射线荧光光谱法(TXRF)同时测定复混肥料中的钒、铬、锰、铁、镍、铜、锌、铅,方法检出限从铅的1.0μg/g到钒的7.0μg/g,精密度(RSD)铬为2.5%,铅为16%,除铅以外,其余元素的RSD均小于10%;方法回收率为80%～120%,Pb的回收率略低主要是由于化肥中As Kα谱线对Pb Lα谱线的干扰导致测定结果偏低。用TXRF和电感耦合等离子体发射光谱法(ICP-AES)测定不同复混肥料中各元素的含量,经统计检验,两种方法测定结果在95%置信区间内无显著性差异。对于金属元素含量较高的样品,TXRF法测定结果的相对标准偏差小于ICP-AES法。对于不同的复混肥料,在微量、痕量元素检测范围内,TXRF法具有较高的准确度和适用性,仪器使用和维护成本低,方法快速准确。     

王水溶矿-等离子体光谱法测定砷矿石和锑矿石中砷锑硫铜铅锌

建立了王水溶矿-电感耦合等离子体发射光谱法测定砷矿石和锑矿石中主、次量元素砷、锑、硫及含量范围在100μg/g以上的铜、铅、锌等元素的方法。研究了放置时间、溶液酸度、氧化剂与络合剂对砷、锑、硫及其他元素测定的影响。不同王水浓度酸度对可同时测定的其他元素的影响不明显;当溶液酸度较小时,不能放置,应及时测定;如需放置,应在溶液定容前加入酒石酸防止水解。样品中砷、锑、硫的含量在0.74%～39.7%时,相对误差(RE)在-0.17%～7.74%,5次独立测定的相对标准偏差(RSD)均小于2%;含量在100～500μg/g以下的Sb,RE在-2.5%～4.79%,5次独立测定的RSD均小于2%。由于稀释倍数较大(DF=1000),不能准确测定含量在100μg/g以下的铜、铅、锌;含量在100μg/g以上的铜、铅、锌的RE在-10.3%～10.3%,5次独立测定的RSD基本小于5%。经标准物质验证获得满意结果。方法也可应用于砷、锑含量较高的硫化矿的测定。     

电感耦合等离子体质谱法同时测定铜铅锌矿石中微量元素镓铟铊钨钼的干扰消除

对电感耦合等离子体质谱法同时测定铜矿石、铅矿石和锌矿石中镓、铟、铊、钨和钼量时,基体效应和主量元素铜、铅、锌对测量的干扰情况及可能的消除方法进行试验,结果表明,溶液中共存小于200μg/mL锌对上述微量元素的测量没有干扰;溶液中共存大于50μg/mL的铜对镓、铟、铊、钨、钼的测量有负干扰,共存大于100μg/mL铅对钨的测量有正干扰,对钼的测量有负干扰,采用钪、铼、镧混合内标或基体匹配可以消除这些干扰;溶液中共存大于20μg/mL的铅对铊的测量有正干扰,选择203Tl为测量质量数,可使耐受铅的干扰浓度提高到50μg/mL,铅对铊测量的干扰可以采用校正系数法或基体匹配进行校正或消除。     

封闭溶样-电感耦合等离子体质谱法测定硫化铅矿石中40种微量元素

铅矿石在电感耦合等离子体质谱测定中,元素Pb的双电荷离子206Pb~(2+)干扰内标元素103Rh而影响其他元素的测定结果。本文建立了用~(105)Pd和~(187)Re的混合溶液为内标溶液,封闭酸溶-电感耦合等离子体质谱测定硫化铅矿石中的铍、钪、钛、铬、钴、镍、铜、锌、镓、锗、砷、锑和稀土等40种微量元素分析方法,提高了电感耦合等离子体质谱分析铅矿石中低质量的元素(质量为133Cs以下的元素)测定数据的准确度。通过大量的实验确定了该方法的检出限为0.04~5.00μg/g,对国家一级标准物质GBW07235(铅矿石)、GBW07236(铅矿石)、GBW07286(铜铅锌矿石)、GBW07287(铅锌矿石)、GBW07165(富铅锌矿石)、GBW07172(铅矿石)进行分析测定,其准确度(RE)均小于10%,加标回收率为90%~120%。     

电感耦合等离子体发射光谱法同时测定钒钛磁铁矿中钒钛钴镍

钒钛磁铁矿样品经过氧化钠熔融,盐酸提取,溶液分取稀释后用电感耦合等离子体发射光谱法同时测定其中的V2O5、TiO2、Co、Ni。实验确定过氧化钠的用量为1.5 g,盐酸的用量为10 mL,选择干扰元素较少和背景干扰较小的V、Ti、Co、Ni分析谱线分别为292.4 nm、334.9 nm、230.7 nm、231.6 nm,在稀释因子为10(总稀释因子5000)的条件下进行分析,方法检出限为0.05～0.17μg/g。用国家一级钒钛磁铁矿标准物质GBW 07225(原矿)、钒钛磁铁矿标准物质GBW 07226a(精矿)、钒钛磁铁矿标准物质GBW 07227(尾矿)验证方法精密度和准确度,方法精密度(RSD,n=12)为0.41%～1.91%;除含量较低的Ni和Co外,相对误差(RE,n=4)均小于5%。通过安装氩气加湿器有效地解决了盐分较大带来的影响,在标准系列中加入等量空白溶液,保持基体与试样一致,消除了基体效应。方法分解样品彻底完全,分析流程简单,易于掌握,一次熔样可以同时测定多种元素,可适用于大批量样品分析。     

K比例H点标准加入吸光光度法同时测定矿样中铌和钽

从样品分解方法入手,探讨了最佳测试条件。用盐酸-氟化氢铵-硝酸-高氯酸溶解试样,在10%的盐酸介质中,用火焰原子吸收光谱仪于波长328.1 nm处,以空气-乙炔火焰测定铅精粉中的银量,克服了用铅析或灰吹法测定的步骤冗长等缺点。用铅精粉国家一级标准物质GBW 07167分析验证,测定结果与标准值吻合。方法精密度(RSD,n=12)为2.2%~4.3%,方法检出限为1.2μg/g。方法分析快速,简单。     

Determination of Zirconium, Niobium, Hafnium and Tantalum at ng g-1 Levels in Geological Materials by Direct Nebulisation of Sample HF Solution into FI-ICP-MS

We have developed a rapid and accurate method to determine Zr, Nb, Hf and Ta (denoted as HFSE) in geological samples by inductively coupled plasma-mass spectrometry fitted with a flow injection system (FI-ICP-MS). The method involves sample decomposition by HF followed by HF dissolution of HFSE coprecipitated with insoluble M and Ca fluoride residues formed during the initial HF attack. This HF solution was directly nebulized into an ICP mass spectrometer. An external calibration curve method and an isotope dilution method (ID) were applied for the determination of Nb and Ta, and of Zr and Hf, respectively. Recovery yields of HFSE were > 96% for peridotite, basalt and andesite compositions, apart from Zr and Hf for peridotite (> 85%). No matrix effects for either signal intensities of HFSE or isotope ratios of Zr and Hf were observed in basalt, andesite and peridotite solutions down to a dilution factor of 100. Detection limits in silicate rocks were 40, 2, 1 and 0.1 ng g-1 for Zr, Nb, Hf and Ta, respectively. This technique required only 0.1 ml of sample solution, and thus is suitable for analysing small and/or precious samples such as meteorites, mantle peridotites and their mineral separates. We also present newly determined data for the Zr, Nb, Hf and Ta concentrations in USGS silicate reference materials DTS-1, PCC-1, BCR-1, BHVO-1 and AGV-1, GSJ reference materials JB-1, -2, -3, JA-1, -2 and -3, and the Smithsonian reference Allende powder.     

Determination of Ge, As, Se and Te in Silicate Samples Using Isotope Dilution-Internal Standardisation Octopole Reaction Cell ICP-QMS by Normal Sample Nebulisation

A method for the determination of Ge, As, Se and Te in silicate samples using isotope dilution-internal standardisation (ID-IS) octopole reaction cell (ORC) ICP-QMS by normal sample nebulisation was developed. The method does not involve either hydride generation or ion exchange. Germanium, Se and Te were determined by isotope dilution (ID), and As was determined by ID-IS. A silicate sample with an added Ge-Se-Te spike was digested with an HF-HNO₃-HBr mixture, dried, re-dissolved with HF and the supernatant liquid was directly aspirated into an ORC-ICP-QMS instrument with He or H₂ gas. No matrix effects were observed down to a dilution factor (DF) of ∼ 70 for Ge, Se and Te and DF of ∼ 1000 for As, which resulted in 3s detection limits in silicates of 2, 1, 0.1 and 4 ng g⁻¹, respectively. Advantages of the method are the simple sample introduction as well as a capability of determining S, Ti, Zr, Nb, Mo, Sn, Sb, Hf and Ta by ID-IS-ICP-QMS/SFMS from the same solution. Furthermore, the total sample solution consumption was only 0.253 ml with DF = 2000. Therefore, only a 0.13 mg test portion was required. To demonstrate the applicability of this technique, Ge, As, Se and Te in eight silicate reference materials were determined, as well as S, Ti, Zr, Nb, Mo, Sn, Sb, Hf and Ta in four carbonaceous chondrites.     

氢醌滴定法测定金矿石中金的不确定度评定

以氢醌滴定法测定金矿石中贵金属金的实例进行不确定度评定。测量结果的不确定度由配制金标准母液、金标准工作液、氢醌滴定液浓度、称样质量、滴定样品所用氢醌溶液体积等所引入的不确定度分量组成。在对各个不确定度分量进行量化的基础上，通过合成得到测量结果的标准不确定度，再乘以95％置信概率下的扩展因子2，得到测量结果的扩展不确定度。     

福建长乐地区海水入侵(上溯)对水化学变化的影响

海水入侵是沿海地区主要环境地质问题,分析沿海地下水和河水水化学特征,对圈定海水入侵范围及判断影响程度具有重要意义。通过在福建长乐市海水入侵含水层和闽江口海水上溯区采取23件水样进行室内常规离子测试,获得了海水入侵(上溯)区水中主要离子含量。利用海水稀释线分析主要离子与Cl离子之间的相对变化,对比离子实际浓度与理想浓度的差异,分析海水入侵对水化学变化的影响。研究结果显示,随着海水与淡水混合,水化学类型从海水到淡水依次为Na-Cl型水-Na-Cl·HCO₃型水-Na·Ca-HCO₃·Cl型水-Ca-HCO₃型水;引起水化学类型和TDS变化的主要因素为Na⁺和Cl^-的增加;Ca²⁺、Mg²⁺高于海水稀释线和理想浓度线,Na⁺、K⁺在海水稀释线和理想浓度线上下跳跃：Br^-/Cl^-与海水稀释线吻合较好,可以作为判断海水入侵范围的依据。     

称重法配制标准溶液研究及其不确定度评估

在标准溶液配制及稀释的过程中放弃了传统的定量移液管,采用精密电子天平作为定量工具。精密电子天平准确度高,重复性好,不需考虑溶液黏度、管口流速等因素对不确定度的影响,而且明显地降低了在标准溶液逐级稀释过程中由于读数、操作等原因产生的误差,可实现大比例稀释,操作简便。根据《化学分析中不确定度的评估指南》(CNAL/AG07:2002)评定了此方法与传统溶液配制方法的不确定度。利用电感耦合等离子体原子发射光谱法(ICP-AES)验证了其准确性和线性,均获得满意结果。本法适用于ICP-AES法测定样品中的主元素(含量在x%~xx%)时的标准溶液配制,也可应用于原子荧光光谱、原子吸收光谱等仪器系列标准溶液的配制。     

Determination of Molybdenum, Antimony and Tungsten at sub μg g−1 Levels in Geological Materials by ID-FI-ICP-MS

We have developed a rapid and accurate method for the determination of Mo, Sb and W in geological samples using isotope dilution inductively coupled plasma-mass spectrometry with a flow injection system (ID-FI-ICP-MS). The chemical procedure requires HF digestion of the sample with a Mo-Sb-W mixed spike, subsequent evaporation and dissolution of Mo, Sb and W from Mg and Ca fluorides with HF. Recovery yields of Mo, Sb and W in the extraction were > 94% for samples of peridotite, basalt and andesite composition, with the exception of W in samples of peridotite composition for which recovery was 81%. No matrix effects were observed in the determination of the isotope ratios of Mo, Sb and W in solutions prepared from peridotite, basalt and andesite samples down to a dilution factor of 100. Detection limits of Mo, Sb and W in silicate materials were at the several ng g⁻¹ level. Analysis of the silicate reference materials PCC-1, DTS-1, BCR-1, BHVO-1, AGV-1 from the US Geological Survey and JP-1, JB-1, -2, -3, JA-1, -2, and -3 from the Geological Survey of Japan as well as the Smithsonian reference Allende powder yielded reliable Mo, Sb and W concentrations. The repeatability in the analysis of basalts and andesites was < 9%. This technique requires only 0.2 ml sample solution, and is therefore suitable for analyzing small and/or precious samples such as meteorites, mantle peridotites and their mineral separates.     

微波消解—冷原子荧光光谱法测定植物样品中的汞

为了简化测量植物中汞含量的方法,提高灵敏度及结果的可信度,实验采用微波消解植物样品的办法,使样品经氯化亚锡还原,再用冷原子荧光测定出植物样品中汞的含量。确定了消解样品的方法和微波消解样品的条件,优化了仪器的最佳工作参数。方法检出限0.30×10-9(稀释因子100倍),精密度(n=12)在2.09%~6.05%,加标回收率94.1%~105.5%,方法经生物国家一级标准物质验证方法准确可靠。     

Determination of Ruthenium,Palladium and Iridium in 27 In ternational Reference Silicate and I Ron-Formation Rocks,Ores and Related Materials By Isotope Dilution Inductively-Coupled Plasma Mass Spectrometry*

Ruthenium, palladium and iridium have been determined in 27 international reference rocks, ores and related materials by inductively-coupled plasma mass spectrometry using isotope dilution and sample introduction by solution nebulization and electrothermal vaporization, after chemical separation by co-precipitation with tellurium. The accuracy of the procedure is discussed by comparison of the results obtained with synthetic solutions and standard samples.