铝合金厚板静止轴肩搅拌摩擦焊接头组织及性能

采用8.5 mm厚度2A14-T4铝合金和自主研制搅拌工具进行静止轴肩搅拌摩擦焊（stationary shoulder friction stir welding,SSFSW）实验,探讨焊接工艺参数对接头组织和力学性能的影响规律。结果表明：只有在低转速工艺参数范围内（转速ω=400~600 r/min与焊接速率v=60~120 mm/min）可获得焊缝表面光滑、无缺陷厚板铝合金SSFSW焊接接头。SSFSW焊缝区主要由焊核区（NZ）组成,周围热力影响区（TMAZ）及热影响区（HAZ）宽度明显减小,焊核区与搅拌针形状类似且由两种不同尺寸细小等轴晶构成,前进侧NZ晶粒比后退侧NZ更为细小。接头显微硬度呈"W"状分布,NZ硬度值可达到母材硬度80%~90%,TMAZ与HAZ交界处存在软化区,硬度最低为母材硬度72%左右。在给定ω=500 r/min,v=140 mm/min焊接参数下,SSFSW接头抗拉强度可达到母材的88%,断裂位置多位于后退侧TMAZ与HAZ交界处软化区,具有韧性断裂特征。     

Formation and mechanical properties of stationary shoulder friction stir welded 6005A-T6 aluminum alloy

6005A-T6 aluminum alloy is welded by stationary shoulder friction stir welding (SSFSW). At a constant rotational velocity of 2000 rpm, the effect of welding speed on mechanical properties of SSFSW joint are investigated in detail. Defect-free joint with gloss surface and small flash is attained and no cracks appear at the bending angle of 180°. Compared with traditional friction stir welding (FSW), width of rotational shoulder affected zone is relatively small because of the smaller diameter of rotational shoulder. Increasing welding speed is benefit for reducing the width of softening region and the softening degree. The fracture position of welding joint locates in thermo-mechanically affected zone and the fracture surface morphology presents the typical ductile fracture. The maximum tensile strength of joint at the welding speed of 400 mm/min reaches 82% of base metal (BM).     

水下搅拌摩擦焊对铝/铜接头组织与性能的影响

目的 采用搅拌摩擦焊,对比分析大气环境和水下环境下铝/铜接头的组织与性能,以期获得力学性能更优异的铝/铜焊接接头。方法 利用搅拌摩擦焊,在焊接速度为40 mm/min、旋转速度为1 000 r/min的条件下,分别在大气环境和水下环境下对厚度为9 mm的6061铝合金板和T2纯铜板进行焊接。然后,对铝/铜界面、焊核区进行扫描电镜及能谱分析,并对铝/铜界面及焊核区进行物相分析,确定产物相组成。最后,对铝/铜试样进行拉伸及硬度检测。结果 铝/铜接头均无裂纹、气孔等缺陷。铜颗粒弥散分布在焊核区,铝/铜界面形成金属间化合物层。水下搅拌摩擦焊下界面元素扩散距离明显变短,且金属间化合物厚度更薄。铝/铜接头的金属间化合物为AlCu和Al4Cu9。大气环境焊接下接头的抗拉强度为130.6 MPa,断裂方式为脆性断裂;水下焊接下接头的抗拉强度为199.5 MPa,断裂方式为韧性断裂。水下环境下的接头硬度值更高,其中热影响区的硬度最低值约为65HV。结论 水下搅拌摩擦焊铝/铜接头无裂纹、气孔等缺陷。组织上,水下搅拌摩擦焊的铝/铜接头界面元素扩散距离更短,硬脆的金属间化合物更少;性能上,水下搅拌摩擦焊的铝/铜接头强度更高,抗拉强度达到199.5 MPa,达到母材的74.4%。     

异种铝合金回填式搅拌摩擦点焊工艺的研究

目的 研究搅拌头转速和轴套下压量对异质铝合金回填式搅拌摩擦点焊接头的组织及力学性能的影响。方法 采用回填式搅拌摩擦点焊技术对7050铝合金和2524铝合金进行搭接焊试验,焊接完成后利用光镜、体式显微镜、扫描电镜对组织进行观察,另外,测试拉伸剪切载荷和显微硬度分布,最后对断裂行为进行了研究。结果 接头区域可以分为焊核区、热力影响区、热影响区、母材4个区域,焊核区晶粒呈细小等轴状,热力影响区晶粒呈粗大长条状。随搅拌头转速的增大,拉剪载荷降低,当转速为1500 r/min时拉剪载荷值最高,其值为7.499 44 kN。热影响区的显微硬度比母材低,最小值为HV106。接头的断裂方式可以分为剪切型断裂、塞型断裂、剪切-半环型断裂。结论 在一定工艺参数范围内,通过适当降低搅拌头转速能显著提高接头的拉剪载荷,轴套下压量对接头的断裂方式影响显著。     

Evaluation of the microstructure and mechanical properties of friction stir welded 6005 aluminum alloy

Abstract

The microstructural change related with the hardness profile has been evaluated for friction stir welded, age hardenable 6005 Al alloy. Frictional heat and plastic flow during friction stir welding created fine and equiaxed grains in the stir zone (SZ), and elongated and recovered grains in the thermomechanically affected zone (TMAZ). The heat affected zone (HAZ), identified only by the hardness result because there is no difference in grain structure compared to the base metal, was formed beside the weld zone. A softened region was formed near the weld zone during the friction stir welding process. The softened region was characterised by the dissolution and coarsening of the strengthening precipitate during friction stir welding. Sound joints in 6005 Al alloys were successfully formed under a wide range of friction stir welding conditions. The maximum tensile strength, obtained at 507 mm min^-1 welding speed and 1600 rev min^-1 tool rotation speed, was 220 MPa, which was 85% of the strength of the base metal.     

铝合金薄板搭接高速 FSW 缺陷及断裂行为

目的 为了拓展搅拌摩擦焊技术应用,对薄板搭接结构高速搅拌摩擦焊工艺优化与工程应用提供 借鉴与指导。方法 采用圆锥无螺纹搅拌针,进行了 6061 铝合金薄板搭接高速搅拌摩擦焊接,对接头界 面缺陷及其断裂模式进行分析,探讨了转速对 6061 铝合金薄板搭接接头成形及性能的影响规律。结果 发现在无螺纹圆锥搅拌针、高转速（6000~9000 r/min）条件下,接头塑性金属在后退侧易形成飞边流出, 导致下板前进侧出现孔洞缺陷,且随转速增大,界面缺陷尺寸逐渐增大,当转速达到 10 000 r/min 时, 孔洞尺寸有所减小,此时接头拉剪强度最高,为 123 MPa。对试样拉剪断裂位置分析发现,高速搭接接 头断裂位置主要有两种,分别断裂在结合界面处或在前进侧下板,且转速在 9000 r/min 以上越趋向于在 结合界面断裂。结论 高转速搭接焊接必须协调轴肩相貌、焊接工装约束等条件,保证接头塑性金属充 分流动而不流失,才能获得成形良好无缺陷的接头。     

Influence of a non-rotating shoulder on heat generation,microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints

Friction stir welding (FSW) and stationary shoulder friction stir welding (SSFSW) were carried out for the butt joining of dissimilar AA2024-T3 and AA7050-T7651 aluminium alloys with thicknesses of 2 mm. A comparison between the two processes was performed by varying the welding speed while keeping the rotational speed constant. Through the analysis of the force and torque produced during welding and a simple analytical model, it was possible to show that in SSFSW there is more effective coupling with the tool and the heat produced is more efficiently distributed. This process decreases both the welding area and the diffusion at the interface of the two alloys compared with FSW. The minimum microhardness occurred at the advancing side (AS) at the interface between the thermo-mechanically affected zone (TMAZ) and the stir zone (SZ) in both processes, although the decrease was more gradual in SSFSW. This interface is also where all specimens failed for both welding technologies. An increase in tensile strength was measured in SSFSW compared with standard FSW. Furthermore, it was possible to establish the mechanical performance of the material in the fracture zone using digital image correlation.     

2219铝合金搅拌摩擦焊接头组织和性能的不均匀性研究

目的 针对2219铝合金搅拌摩擦焊接头受焊接热作用和机械搅拌作用的影响,极易产生组织和力学性能不均匀的情况,深入研究接头的局部力学性能,为焊接工艺优化提供理论指导.方法 采用显微组织分析与数字图像相关(DIC)技术测试相结合的方法,对2219铝合金搅拌摩擦焊接头的组织和局部力学性能进行表征,并建立搅拌摩擦焊接头各区域的局部力学性能模型.结果 2219铝合金搅拌摩擦焊接头的力学性能薄弱区为热机影响区.试样断裂前该区域局部应力达到345 MPa,局部应变为18.9％,而此时母材应变仅为1.91％.结论 热机影响区的组织在焊接热作用和机械搅拌的双重作用下发生了粗化和软化,导致该区的力学性能降低,是整个焊接接头的薄弱区域.     

Effect of welding parameters on microstructure and mechanical properties of AA6061-T6 butt welded joints by stationary shoulder friction stir welding

Stationary shoulder friction stir welding (SSFSW) butt welded joints were fabricated successfully for AA6061-T6 sheets with 5.0 mm thickness. The welding experiments were performed using 750–1500 rpm tool rotation speeds and 100–300 mm/min welding speeds. The effects of welding parameters on microstructure and mechanical properties for the obtained welds were discussed and analyzed in detail. It is verified that the defect-free SSFSW welds with fine and smooth surface were obtained for all the selected welding parameters, and the weld transverse sections are obviously different from that of conventional FSW joint. The SSFSW nugget zone (NZ) has “bowl-like” shapes with fairly narrow thermal mechanically affected zone (TMAZ) and heat affected zone (HAZ) and the microstructures of weld region are rather symmetrical and homogeneous. The 750–1500 rpm rotation speeds apparently increase the widths of NZ, TMAZ and HAZ, while the influences of 100–300 mm/min welding speeds on their widths are weak. The softening regions with the average hardness equivalent 60% of the base metal are produced on both advancing side and retreating side. The tensile properties of AA6061-T6 SSFSW joints are almost unaffected by the 750–1500 rpm rotation speeds for given 100 mm/min, while the changing of welding speed from 100–300 mm/min for given 1500 rpm obviously increased the tensile strength of the joint and the maximum value for welding parameter 1500 rpm and 300 mm/min reached 77.3% of the base metal strength. The tensile fracture sites always locate in HAZ either on the advancing side or retreating side of the joints.     

Effect of friction stir welding process parameters on the tensile strength of dissimilar aluminum alloy AA2024-T3 and AA7075-T6 joints

This work investigates the influence of friction stir welding parameters on the mechanical properties of the dissimilar joint between AA2024-T3 and AA7075-T6. Experiments are conducted consistent with the three-level face-centered composite design. Response surface methodology is used to develop the regression model for predicting the tensile strength of the joints. The analysis of variance technique is used to access the adequacy of the developed model. The model is used to study the effect of key operating process parameters namely, tool rotation speed, welding speed and shoulder diameter on the tensile strength of the joints. The results indicate that friction stir welding of aluminum alloys at a tool rotation speed of 1050 min⁻¹, welding speed of 40 mm/min and a shoulder diameter of 17.5 mm would produce defect less joint with high tensile strength.     

转速对6061铝合金搅拌摩擦搭接焊接头组织和力学性能的影响

目的 研究不同转速条件下6061铝合金搅拌摩擦搭接焊接头组织和力学性能的变化规律,为工程实践应用提供参考。方法 在不同旋转速度(800、1 200、1 500 r/min)下对4 mm厚的6061铝合金进行搅拌摩擦搭接焊实验,固定进给速度和轴肩下压量,研究搅拌头转速对接头宏观组织、微观组织和力学性能的影响。结果 所有接头均没有出现明显缺陷,当转速为1 500 r/min时,搅拌区晶粒尺寸细化明显,最大失效载荷达到母材的75%,上板和下板的硬度曲线都呈“W”形;当转速为800 r/min和1 200 r/min时,下板硬度曲线呈“V”形。随着转速的增大,有效搭接宽度逐渐增大,接头的平均拉剪强度也在增大,所有接头都在前进侧断裂,断裂形式均为拉伸断裂。结论 转速的提升增加了焊接热输入量和机械搅拌作用,促进了有效搭接宽度的增大和晶粒尺寸的细化,但未能改变钩状缺陷的形成及延伸方向。当转速为1 500 r/min时,热输入量较大,搅拌区范围相对较大,下板存在更大面积的搅拌区,其硬度规律与上板的相似。所有接头均为拉伸断裂,断裂位置在热影响区附近,说明搭接接头连接良好。     

铝/镁搅拌摩擦焊-钎焊焊接接头微观组织结构

目的研究不同工艺参数下钎料Zn的添加对Al/Mg异种金属搅拌摩擦焊-钎焊焊接接头组织和性能的影响。方法以厚度为0.05 mm的纯Zn作为钎料,对3 mm厚的2A12-T4态铝合金和4 mm厚的AZ31变形镁合金,进行搅拌摩擦焊-钎焊的复合焊接,分析锌夹层的添加对接头微观组织与力学性能的影响。结果当添加Zn中间层时,接头钎焊区缓解了拉伸断裂趋势,在焊接速度为23.5 mm/min,旋转速度为375 r/min时,接头抗拉剪力达到5.5 k N,复合焊接接头的钎焊焊缝由搭接区、固相扩散区、钎焊区组成。结论钎料的添加有效阻止了Al-Mg系金属间化合物的形成。     

基于响应面法的5052铝合金搅拌摩擦焊接工艺参数研究

目的 建立搅拌摩擦焊接工艺参数与焊接接头抗拉强度之间关系的响应曲面模型,并依此模型研究焊接工艺参数变化对接头抗拉强度所产生的影响,得到最佳工艺参数,提高焊接接头强度。方法 以5052-H112铝合金为研究对象,基于响应面法优化设计试验方法,以转速、焊接速度、轴肩压入深度为因素,焊接接头的抗拉强度为响应值设计试验,建立对应的响应函数与回归模型,对模型进行方差分析,根据模型得到最佳工艺参数值,并与试验结果作比较。结果 成功建立了响应模型,在分析模型和试验验证后发现,在选定的工艺参数范围内,当转速为737 r/min、焊接速度为60 mm/min、轴肩压入深度为0.3 mm时,接头抗拉强度达到最优值227 MPa。结论 通过响应面分析得到,转速和焊接速度对抗拉强度的影响最大,且两者交互作用显著,在给定范围内随着转速和焊接速度的提高,抗拉强度增大至峰值后下降,轴肩压入深度单独对接头抗拉强度的影响较小,其与转速交互影响显著。通过响应曲面法优化后的焊接工艺参数明显提高了5052-H112铝合金搅拌摩擦焊焊接头抗拉强度。     

Joint properties of dissimilar Al6061-T6 aluminum alloy/Ti–6%Al–4%V titanium alloy by gas tungsten arc welding assisted hybrid friction stir welding

Hybrid friction stir butt welding of Al6061-T6 aluminum alloy plate to Ti–6%Al–4%V titanium alloy plate with satisfactory acceptable joint strength was successfully achieved using preceding gas tungsten arc welding (GTAW) preheating heat source of the Ti alloy plate surface. Hybrid friction stir welding (HFSW) joints were welded completely without any unwelded zone resulting from smooth material flow by equally distributed temperature both in Al alloy side and Ti alloy side using GTAW assistance for preheating the Ti alloy plate unlike friction stir welding (FSW) joints. The ultimate tensile strength was approximately 91% in HFSW welds by that of the Al alloy base metal, which was 24% higher than that of FSW welds without GTAW under same welding condition. Notably, it was found that elongation in HFSW welds increased significantly compared with that of FSW welds, which resulted in improved joint strength. The ductile fracture was the main fracture mode in tensile test of HFSW welds.     

焊接速度对 7A52 铝合金 FSW 组织及力学性能的影响

目的在保证搅拌速度一定时,针对8 mm厚的7A52铝合金,在不同焊接速度下采用搅拌摩擦焊(FSW)进行焊接试验,研究其焊接接头的显微组织及力学性能。方法利用搅拌摩擦焊机进行对接焊接,焊后制取金相试样观察焊接接头宏观形貌和显微组织,并测定其力学性能。结果7A52铝合金FSW焊接接头焊核区的面积随着焊接速度的增大而增大,当焊接速度为250mm/min时,焊接接头的焊核区面积最大,焊核区的显微组织都为细小的等轴晶,焊接接头横截面的焊核区呈明显"洋葱环"的形貌,而热力影响区的结构特征则呈现出了较高的塑性变形流线层。焊接接头显微硬度分布都呈现出"W"形变化,在焊接速度为150 mm/min时,焊接接头的平均抗拉强度能达到452 MPa,达到了母材抗拉强度的89%。结论通过对不同焊接速度下7A52铝合金FSW焊接接头的组织和性能进行研究,得到了不同焊接速度下焊接接头组织和力学性能。     

Identification of the pin offset effect on the friction stir welding (FSW) via Taguchi – Grey relational analysis: A Case study for AA 7075 – AA 6013 alloys

The aim of this work is to present a case study relating to the dissimilar friction stir welding (FSW) ability of AA 7075‐T651 and AA 6013‐T6 by applying pin offset technique. An orthogonal array L18 was conducted to perform the overlapped weld seams using three different values of pin offset, welding speed and tool rotational speed along with two different pin profiles determine the impact of welding parameters on the tensile properties of friction stir welded joints. The nugget zone for each of overlapped weld seams exhibited a complex structure and also, the pin offset and profile also were found to have a great impact on the microstructural evolution of the nugget zone. The ultimate tensile strength, elongation at the rapture and bending strength of welded joints were measured in the ranges of 194–215 MPa, 1.79–3.34 % and 203–352 MPa. From the Taguchi based Grey relational analysis, the optimum welding condition was determined for the welded joint performed using a single fluted pin profile with the zero pin offset, tool rotational speed of 630 min^?1 and welding speed of 63 mm/min. Microstructural and macro‐structural observations revealed that welded joints exhibiting lower tensile strength are consistent of various types of defects (e. g. cracks, tunnels and cavities). The fracture location of welded joints was found to be on the heat affected zone and between the heat affected zone and AA 6013‐base metal. The tool and pin wear was not observed during the welding applications     

Effect of pin offset on the mechanical properties of friction stir welded AA 6013 aluminum alloy plates

In this study, AA 6013 aluminum plates were butt‐welded with friction stir welding via pin offset technique. Macrostructural observations revealed that kissing bonds, originated from the broken oxide layers, were found to occur in the welded joints. The fracture location of welded joints after tensile tests was found to be outside the joint area, revealing that kissing bonds which were formed in the stir zone exhibited no detrimental effect on the mechanical properties of joints. Microstructural observations revealed that phases belonging to Mg₂Si, Al₄Cu₂Mg₈Si₇ and Al(MnFe)Si were observed in the x‐ray diffraction pattern of friction stir welded joints. The highest tensile strength with a value of 206 MPa was achieved with the process parameters of 1.5 mm pin offset towards the advancing side and 500 min^?1 tool rotational speed, leading the ratio of tensile strength of joint to ultimate tensile strength of base metal, also known as joint efficiency, to reach 74 %.     

Effect of welding speed on microstructure and mechanical properties of friction stir welded copper

The 3-mm-thick copper plates were friction stir welded at a low tool rotation rate of 600 rpm. The influence of welding speed on microstructure and mechanical properties of the joints was investigated. As the welding speed increased, the grain size of nugget zone first increased and then decreased, the thermo-mechanically affected zone became narrow and the boundary between these two zones got distinct, but the heat affected zone was almost not changed. The ultimate tensile strength and elongation of the joints increased first and decreased finally with increasing welding speed, but the effect was little when the welding speed is in the range of 25–150 mm/min. The defect-free joints were produced at lower welding speeds, and the fracture locations were outside the nugget zone on the retreating side. With increasing welding speed, the average hardness of nugget zone decreased first and then increased, but welding speed had little effect on the hardness of the other regions within the joints.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

2A12铝合金筋板件T型搅拌摩擦焊工艺及焊后热处理

为评价2A12铝合金筋板件搅拌摩擦焊工艺并探寻提高接头强度的途径,进行了2A12铝合金筋板件的T型搅拌摩擦焊焊接工艺试验,并对不同人工时效热处理下焊接接头的微观组织及性能进行了研究.研究表明:采用T型搅拌摩擦焊即可实现2A12铝合金筋板件的成形,当搅拌头旋转速度为750 r/min、焊接速度60mm/min时,接头的抗...