共查询到20条相似文献,搜索用时 46 毫秒
1.
2.
《制冷与空调(四川)》2017,(5)
回转式空预器漏风是科研人员和电厂一直关心和急切解决的核心问题。介绍了新型的密封回收技术,通过对应用密封回收技术的空预器内流体的换热流动进行了数值模拟,得出了此回收技术可以有效降低漏风率。在华润#1机组空预器上应用此密封系统并进行漏风率测试和经济效益分析,结果证明此密封回收系统可以降低漏风,减少热损失排放以及带有可观的经济效益,为今后电厂同类空预器密封改造提供了一定指导和参考。 相似文献
3.
本文介绍了苏联对空分装置单元设备以及整个防爆系统工艺流清除爆炸性杂质和二氧化碳的效率的研究情况,从而确定在原料气流浓度下系统各设备工艺流清除杂质的程度。指出了由蓄冷器、环流气体吸附器、液体过滤器、位于过冷器后的液空吸附器和液氧流上循环回路吸附器组成的空分装置通用防爆系统,可保证设备安全运转。表1。 相似文献
4.
本讲为空分设备可逆式换热器中CO2和H2O自清除原理。讲了H2O和CO2的析出温度区域;自清除条件;冷热气体之间的传热温差,以及达到的两种方法:中抽法、环流法。图9表1。 相似文献
5.
对于中和室内的脉冲气体,用蒙特卡罗方法模拟了气体压力沿轴向的分布。并用模拟进气系统和气压瞬时测量系统,对模拟结果进行了验证。得到与模拟结果较为一致的曲线,从而为注入器真空系统的设计提供了可靠的依据。并通过实验结果,给出了气体靶厚的建立时间约为60ms。 相似文献
6.
7.
以大面积喷淋式平板电极甚高频等离子体增强化学气相沉积(VHF-PECVD)反应室为研究对象,利用FlexPDE和CFD-ACE+商业软件,对反应室电极间的电场和流场分布进行了数值模拟。根据数值模拟结果可知:对于大面积喷淋式平板电极VHF-PECVD反应室,电极间气体流速分布呈现管流特征,而气压分布和电场分布具有类似的分布规律,即在大面积电极中央区域电场较强气压较高,而电极边缘区域电场较弱气压较低;另外,反应室采用喷淋式平板电极进行反应气体馈入,气体总流量、工作气压和电极间距是调节电极间气压分布均匀性的重要参量,采用大电极间距、高工作气压,以及小的气体总流量有助于获得均匀的气压分布。 相似文献
8.
目前国内在对G6以上膜式燃气表进行检定时,采用的标准装置主要有钟罩式气体流量标准装置和标准表法气体流量标准装置两大类,而标准表法气体流量标准装置所用的标准器一般多使用临界流流量计和容积式流量计为标准器,容积式流量计中常用来做标准器的有气体腰轮流量计和湿式气体流量计,速度式流量计一般应用于较大流量(>100m3/h)的测量应用中,因而在对皮膜表的测量中很少使用.G6以上膜式燃气表流量标准装置分类如图1所示. 相似文献
9.
10.
11.
为了开发具有最佳流量分配性能的小管径空调分配器,本文采用数值仿真和空气-水实验相结合的方法评价了常用分配器的分流性能,提出分配器的结构优化方法,并利用空调整机实验验证了该结构优化方法的改进效果。对于三种比较适合于小管径空调器的分配器进行的实验和计算表明,插孔式分配器的分流性能最佳,在额定制冷和额定制热工况下流量分配不均匀度均小于6%;实验结果与仿真计算得出的分配器流量分配不均匀度结果吻合,计算结果与实验的偏差都在15%以内。利用验证过的仿真模型,对插孔式分配器进行结构优化,优化后的分配器应用于空调整机后,系统能效提高了2.2%~2.7%。 相似文献
12.
13.
:IGCC(整体煤气化联合循环 )、PFBC(增压流化床联合循环 )等新型、高效的能源清洁转换系统都需要一套运行可靠、高效、维护简单的高温或常温气体净化装置。本文利用光导纤维浓度测试仪对带有内置过滤元件的三维流化床实验台的流动进行了实验研究。运用FFT方法对颗粒浓度时间序列进行了大量的概率分析和统计。结果表明 ,局部颗粒浓度、L阀、卸料口的位置和气 -固混合特性对颗粒层的形成有重要影响 ,床内气固混合以低频为主 ,在距离布风板z =2 5 0mm附近颗粒浓度较高 ,混合较好 ;径向在壁面附近、边角处颗粒浓度较高 ,混合较好 相似文献
14.
介绍了60000m3/h空分设备空冷塔激冷水分配器故障现象和故障具体部位的确认过程;分析了激冷水分配器故障的原因,最后简述了预防措施。 相似文献
15.
Abdallah S. Berrouk Allen Huang Shivkumar Bale Priyanka Thampi Krishnaswamy Nandakumar 《Advanced Powder Technology》2017,28(11):2947-2960
Catalyst regeneration process has recently been the subject of comprehensive research investigations focusing mainly on the chemistry of the regeneration while overlooking the bed hydrodynamics and its effects on the regeneration performance. For this purpose, an industrial Fluid Catalytic Cracking (FCC) regenerator is simulated using a Multi-Phase Particle-In-Cell (MP-PIC) approach. The simulation is performed using a three-dimensional regenerator design with complex internals in order to study bed hydrodynamics, thermal effects, and chemical kinetics. The numerical model is then used to study typical industrial issues linked to the operation of industrial regenerators such as erosion areas, standpipe drainage, and CO emission levels. It is noticed that total outlet gas flow exceeds total inlet flow due to the formation of coke combustion products, an undersized standpipe, and inefficient placement of the air distributor rings. Highest erosion occurs in the feed line and plate. A low-temperature column exists in the center of the unit, and the highest temperatures are outside of the diplegs in the periphery of the freeboard. Elevated CO levels are present in the outlet gas because of poorly designed air distributor rings and lower than optimal temperatures in the unit. These simulation results show the numerous modeling capabilities of the MP-PIC approach to identify possible performance and reliability issues of an industrial process. Some redesign proposals have been made to enhance the FCC regenerator operations. 相似文献
16.
采用德国德图testo-410多功能风速仪,对终南餐厅的室内空气温度、相对湿度以及气流速度进行了实测。并对结果进行了数据分析,来探究蒸发式冷气机通风降温系统在该餐厅的应用效果。结果表明如果能够对排风系统进行优化改善,蒸发式冷气机系统在终南餐厅的应用效果会更好。 相似文献
17.
冷却吊顶空调系统运行能耗的模拟与算例 总被引:1,自引:0,他引:1
提出冷却吊顶空调系统运行能耗的计算机动态模拟评价方法。在建立系统数学模型的基础上。编制计算机模拟程序,对某建筑物采用冷却吊顶系统的实际运行过程进行逐时模拟,以此来判断冷却吊顶系统应用的可行性及合理性,分析表明,冷却吊顶水系统与新风水系统相独立这一新的系统形式具有良好的节能效果。 相似文献
18.
针对国内散装水泥车罐体设计中不能充分利用流体软件Fluent的情况,利用VB 6.0编程语言编程开发人机交互界面,对Fluent软件进行二次开发,实现散装水泥车罐体卸料过程的数值模拟的专用功能;通过一个实例模拟散装水泥罐车在卸料过程中布风板对卸料过程的影响。结果表明,把Gambit和Fluent内部封装,界面直观、操作简单,能够很好地模拟水泥罐车流态化与卸料过程,并应用到水泥车罐体的开发中;增大布风板的直径能够有效地减少卸料时间,提高卸料效率,并且提高卸料过程的平稳性,在条件允许的情况下应增大布风板的直径。 相似文献
19.
20.
《Advanced Powder Technology》2014,25(1):281-291
Blast cap is the key component of air distributor in circulating fluidized bed (CFB) boilers. Its configuration and performance affects the fluidization quality of the bed, as well as the boiler performance. With the advantage of controlling the jet penetration characteristics and the resistance coefficient individually, bell type blast cap has been widely applied in big-scale utility CFB boilers. Moreover, the inner circuitous gas pass of the bell-type blast cap is able to prevent the bed material from flowing backward into the air chamber effectively, and its tube shield is also convenient to be maintained and replaced. Consequently, the bell-type blast cap is also fit for the small scale industrial CFB boilers with lower operation and maintenance levels in spite of higher manufacturing cost. At present, bell type blast cap is mainly applied in the large scale utility CFB boilers, seldom employed in the small scale industrial CFB boilers with lower bed pressure drop. In the study, aim to acquire favorable fluidization quality and reasonable pressure drop of the bed of small scale industrial CFB boiler, the air jet penetration characteristics of the bell type blast cap were investigated in static beds composed of two typical solids in CFB individually, and the impacts of the inner configuration on blast cap’s resistance characteristics were studied via numerical simulation. The detailed design principle and approach of bell type blast cap was proposed finally based on the study results. 相似文献