镍基喷焊涂层与钛合金基体界面特征的研究

考察了三种工艺制备的镍基喷焊涂层与钛合金基体结合界面的组织形貌、涂层横切面上合金元素的扩散和显微硬度的变化,分析了它们的界面特征及影响因素.结果表明:镍基喷焊涂层与基体钛合金的结合是基于合金元素扩散的冶金结合,合金元素的扩散对涂层与基体能否形成冶金结合具有决定性的影响,钛合金表面的活化处理、涂层合金重熔时液态停留时间以及喷焊后进行时效处理是影响合金元素扩散的主要因素.     

超音速电弧喷涂Ti-Al涂层抗滑动磨损性能研究

采用二次正交回归试验设计原理和钛铝双丝超音速电弧喷涂Ti-Al合金复合涂层方法，对LY12铝合金进行了表面强化研究，并采用金相、XRD、SEM、硬度和磨损试验方法，对涂层的组织结构及力学性能进行了表征，考察了喷涂工艺参数对涂层孔隙率、显微硬度和耐滑动磨损性能的影响，研究结果表明：在本文的实验条件下，涂层的体积磨损量、孔隙率、显微硬度与喷涂电压和喷涂距离之间的变化规律，可用回归模型进行描述；随喷涂电压的增大，涂层磨损量逐渐下降；喷涂距离小于220mm时，随喷涂距离的增大涂层磨损量逐渐增大；喷涂距离为220mm时，磨损量达到最大，继续增加喷涂距离，涂层的磨损量逐渐下降；在干摩擦条件下，Ti-Al合金涂层的磨损机制主要以化合物相剥落引起的磨粒磨损和氧化磨损为主。     

镍、铁基喷焊层组织与性能研究

为寻找具有耐盐酸腐蚀能力的喷焊用合金粉末,自行设计了3种喷焊粉末,并对比研究了自制粉末与商业Ni60粉氧乙炔喷焊层的显微硬度、显微组织形貌和耐盐酸腐蚀性能.结果表明,自制1号粉喷焊层的显微硬度值明显高于商业Ni60喷焊层,自制2号粉喷焊层的显微硬度和耐蚀性均优于商业Ni60喷焊层.分析认为,钼的加入可改善合金粉末的喷焊工艺性,提高喷焊层的耐盐酸腐蚀性能;铬含量的增加显著提高了喷焊层的显微硬度;喷焊层中铁含量的增加对耐盐酸腐蚀性能有不利影响.     

火焰喷涂高熵合金增强铜基复合涂层的组织和耐磨性研究

为了研究AlCoCrFeNi高熵合金(HEA)的加入对铜基复合涂层形貌、显微硬度和耐磨性的影响,以火焰喷涂法在40Cr钢表面制备了AlCoCrFeNi/Cu复合涂层,并采用X射线衍射仪、显微硬度计、扫描电镜和高速摩擦磨损试验机等对涂层的组织及耐磨性进行了测试表征.结果 表明:高熵合金(HEA)由BCC和FCC双相固溶体...     

AlCrNiFeTi高熵合金涂层的电火花沉积制备与摩擦磨损性能

采用真空电弧熔炼法制备直径为7 mm AlCrNiFeTi高熵合金(high-entropy alloy,HEA)作为电极,使用电火花沉积技术在304不锈钢表面成功制备了AlCrNiFeTi高熵合金涂层。通过XRD、OM、EDS、SEM、显微硬度计、摩擦磨损试验机对涂层的微观组织结构和摩擦磨损性能进行研究。结果表明,AlCrNiFeTi电极与涂层均以BCC1和BCC2简单固溶体为主,电极微观组织结构呈典型的树枝晶。涂层由沉积点堆叠铺展形成,表面均匀致密呈橘皮状、凸凹不平,为喷溅花样展开,涂层截面结构无宏观缺陷,厚度约为59.67μm。AlCrNiFeTi涂层最大显微硬度为587.3HV_0.2,比基材的硬度提高了约2.45倍。随着载荷的增大,涂层的磨损机制由氧化磨损和轻微磨粒磨损转变为磨粒磨损和黏着磨损。当摩擦载荷为5 N时,磨损率为1.213×10^-3 mm³/(N·m),摩擦因数仅为0.446,涂层的磨损率较基材的磨损率减小了约28.3%。     

激光熔覆Fe60Nb20Ti20非晶合金粉末及组织性能研究

采用激光熔覆工艺在45钢表面对Fe60Nb20Ti20非晶合金粉末进行不同工艺参数熔覆试验,获得无裂纹且呈冶金结合的涂层。利用扫描电镜、X射线衍射仪、显微硬度计、摩擦磨损试验机对涂层的微观形貌、组成相、显微硬度和摩擦磨损性能进行分析。结果表明,涂层组织为细小的α-Fe过饱和固溶体等轴晶和少量的非晶相。涂层平均硬度为857HV,为基体材料的4倍,耐磨性也明显优于基体材料。     

CoCrFeNiTix高熵合金涂层的显微组织和耐磨性能

用激光熔覆工艺在40Cr钢表面制备CoCrFeNiTi_x (x=0、0.2、0.5、0.8)高熵合金涂层并计算其热力学参数,使用X射线衍射仪(XRD)、扫描电镜(SEM)、能谱仪(EDS)、显微硬度仪、摩擦磨损试验机等手段检测合金的物相组成、组织、元素分布、硬度及耐磨性,研究了Ti元素含量对其显微组织和耐磨性能的影响。结果表明：随着Ti元素含量的提高,合金物相在面心立方(FCC)结构的基础上形成了体心立方(BCC)结构,熔覆层中部的组织由晶界明显、晶粒分布均匀的等轴晶组成,最后形成了柱状树枝晶;随着Ti元素含量的提高,合金横截面的硬度逐渐提高,最高为412.32 HV_0.2,比基体的硬度提高了1.8倍;涂层的磨损量和摩擦系数均随之降低,Ti含量为0.8时涂层其耐磨性能最优,磨损量最小为6.8 mg,摩擦系数为0.35。涂层的磨损机制,以磨粒磨损、粘着磨损和氧化磨损为主。     

几种火焰喷焊自熔性合金层的耐磨性能

研究了不同自熔性合金粉末火焰喷焊层的显微组织与抗磨粒磨损性能，并对其磨面形貌进行了ＳＥＭ观察分析。结果表明，在Ｎｉ６０自熔性合金中加入适量的镍包ＷＣ粉末可明显提高其喷焊层的抗磨粒磨损性能。当ＷＣ的加入量为３５％（ｗｔ）左右时，该喷焊层与６０Ｓｉ２Ｍｎ调质钢相比，相对的耐磨性可提高６倍以上。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

Cr12MoV钢表面激光熔覆Ni60合金制备无开裂涂层及摩擦磨损性能研究

为了实现损伤Cr12MoV钢激光再制造,采用激光熔覆Ni60合金制备无开裂涂层。利用着色探伤剂、硬度计、光学显微镜(OM)、X射线衍射仪(XRD)和摩擦磨损仪对所制备Ni60合金涂层的表面开裂、硬度、金相组织进行分析,并用摩擦磨损试验机对比研究了Ni60合金涂层和Cr12MoV钢的摩擦磨损性能。结果表明,当Ni60合金涂层长度L≤9 mm时,涂层表面无开裂;当Ni60合金涂层长度L>9 mm时,开裂区出现在母材邻近区,且随着涂层长度增大,开裂区也出现在涂层表面。要抑制激光熔覆过程中Ni60合金近母材区开裂,关键在于减少热输入对母材区的作用时间。最后,通过优选表面硬度相近的Ni60合金涂层和Cr12MoV钢进行摩擦磨损性能测试,发现两者的摩擦系数与耐磨性能相近,可望为损伤Cr12MoV钢激光再制造提供参考。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.